Search

The cold compression behavior of alumina samples, with average grain sizes of 350 nm, 7.9 μm, and 18.2 μm, has been investigated under non-hydrostatic conditions by using a diamond anvil cell. After treatment with various pressures, the in situ axial X-ray diffraction patterns, transparency variations, and microstructures after decompression of the samples were also analyzed. The results showed that the submicron grains became easily translucent. The larger the grain size, the higher the pressure needed to compress the sample to transparency. On the other hand, for a similar grain size, the various geometrical shapes of the grains did not affect the pressure dependency on transparency. The elastoplastic characteristics of the alumina grains of different sizes under cold compression were found to be consistent with the transparency variation. As a conclusion, alumina particles under cold compression were found to be applicable in the pressure-assisted preparation of alumina transparent ceramics. [ABSTRACT FROM AUTHOR]

Studying the mechanical and thermal properties as well as the relationship between microstructure evolution and strengthening mechanisms is crucial for obtaining superior high-temperature refractory molybdenum disilicide-silicon carbide composites. In this study, molybdenum disilicide and silicon carbide powders with different volume ratios were used to fabricate molybdenum disilicide-silicon carbide composites via high pressure and high temperature at 5.5 GPa/1773 K. The introduction of the second phase improved the materials' mechanical properties. Transmission electron microscopy demonstrated that severe plastic deformation generated numerous micro-defects and grain refinement during the high pressure sintering process. The second phase enhancement also improved the samples' performances. Under high pressure and high temperature sintering process, the thermal and mechanical properties of the materials increased dramatically, including a well Vickers hardness (~20.6 GPa), fracture toughness (~10.3 MPa·m1/2) and thermal stability (>1673 K). [ABSTRACT FROM AUTHOR]

High-performance polycrystalline cubic boron nitride (PcBN) was sintered without binders at 1500 °C in a pressure range from 11 to 15 GPa using commercial micrometre cubic boron nitride (cBN) with a diameter of approximately 2–4 μm. The results demonstrated that the sample sintered at 12 GPa and 1500 °C had the best mechanical properties and thermal stability. Its average Vickers hardness, fracture toughness, and thermal stability was 63 GPa, 15 MPa m1/2, and 1315 °C, respectively. The considerable improvement in the mechanical properties was mostly attributed to the high compactness, close bonding between grains, and the sample's internal defect structures. The relatively small specific surface area of the micron grains provides an advantage due to its high thermal stability. The amorphous regions observed in the sample's local areas may provide a new strengthening mechanism under high pressure and temperature. [ABSTRACT FROM AUTHOR]

High pressure obviously decreased the sintering temperature of high melting point ceramics and produced bulks with excellent mechanical and thermal properties. In this study, the effect of pressure alone on the densification process of alumina ceramics was demonstrated. The translucent alumina bulks with unexpected hardness were obtained by compressing α-Al 2 O 3 powder under ultra-high pressure at room temperature. Through analyzing microstructure and hardness of cold compressed samples, the results reveal that ultra-high pressure could crush alumina grains under appropriate pressure, and initiate plastic deformation of grains when the applied pressure exceeds the yield strength of alumina. Thus to enhance the hardness of the samples by grain boundary strengthening and plastic deformation at higher pressure. [ABSTRACT FROM AUTHOR]

Abstract High-pressure strengthening is reported to be an effective approach to strengthen materials in addition to traditional nanocrystalline strengthening. Numerous studies have proven that high pressure is an important factor for improving the mechanical properties of materials. Here, we sintered high-purity sub-micron tungsten carbide (sm-WC) ceramics without any additives under a high pressure of 10 GPa and temperatures ranging from 1000 °C to 1500 °C. Numerous microdefects (stacking faults and twins) were introduced inside the grains, and the Vickers hardness of the well-sintered WC bulks reached a high value of 33 GPa, which could be compared with that of single crystal and nanocrystalline counterparts. Thus, the high-pressure strengthening can be applied to the WC system and improves the mechanical properties. The strengthening mechanism is that the high pressure can make the grains take place bulk yield, promote a severe plastic deformation, and introduce numerous microdefects. These defects act as obstacles against dislocations glide during deformation, and thus improve the mechanical properties. [ABSTRACT FROM AUTHOR]