Search

Copper-based catalysts are widely used in methanol steam reforming to produce hydrogen. In this paper, the supportive effect of the crystal phase of ZrO2 on Cu-based catalysts in methanol steam reforming is discussed. Monoclinic(m-), Tetragonal(t-) and mixed ZrO2 phases were prepared, and structure–activity relationships were investigated with XRD, H2-TPR, BET, HR-TEM and XPS. It was found that the catalyst with a 81.4% monoclinic ZrO2 crystal phase exhibited the highest methanol conversion (88.5%) and the highest hydrogen production rate (104.6 μmol/gcat·s) at 275 °C as it displayed the best reducing properties and more oxygen vacancies on the catalyst surface. Oxygen vacancies can produce more Cu1+ + Cu0, which is the active species for methanol steam reforming on the catalyst surface, and therefore affect catalytic activity. [ABSTRACT FROM AUTHOR]

Photoelectrocatalytic hydrogen production was studied by using a photoelectrochemical cell where the photoanode was made by depositing on FTO electrodes either a nanoparticulate WO3 film alone or a bilayer film made of nanoparticulate WO3 at the bottom covered with a nanoparticulate TiO2 film on the top. Both the electric current and the hydrogen produced by the photoelectrocatalysis cell substantially increased by adding the top titania layer. The presence of this layer did not affect the current-voltage characteristics of the cell (besides the increase of the current density). This was an indication that the flow of electrons in the combined semiconductor photoanode was through the WO3 layer. The increase of the current was mainly attributed to the passivation of the surface recombination sites on WO3 contributing to the limitation of charge recombination mechanisms. In addition, the top titania layer may have contributed to photon absorption by back scattering of light and thus by enhancement of light absorption by WO3. Relatively high charge densities were recorded, owing both to the improvement of the photoanode by the combined photocatalyst and to the presence of ethanol as the sacrificial agent (fuel), which affected the recorded current by "current doubling" phenomena. Hydrogen was produced under electric bias using a simple cathode electrode made of carbon paper carrying carbon black as the electrocatalyst. This electrode gave a Faradaic efficiency of 58% for hydrogen production. [ABSTRACT FROM AUTHOR]

Hydrogen production by the electrolysis of water is a green and efficient method, which is of great significance for achieving sustainable development. Molybdenum disulfide (MoS2) is a promising electrocatalyst for hydrogen evolution reaction (HER) due to its high electrochemical activity, low cost, and abundant reserves. In comparison to the noble metal Pt, MoS2 has poorer hydrogen evolution performance in water electrolysis. Therefore, further modifications of MoS2 need to be developed aiming at improving its catalytic performance. The present work summarizes the modification strategies that have been developed in the past three years on hydrogen evolution from water electrolysis by utilizing MoS2 as the electrocatalyst and following the two aspects of internal and external modifications. The former includes the strategies of interlayer spacing, sulfur vacancy, phase transition, and element doping, while the latter includes the heterostructure and conductive substrate. If the current gap in this paper's focus on modification strategies for electrocatalytic hydrogen evolution in water electrolysis is addressed, MoS2 will perform best in acidic or alkaline media. In addition to that, the present work also discusses the challenges and future development directions of MoS2 catalysts. [ABSTRACT FROM AUTHOR]

Anion modification and trace metal doping have been widely demonstrated to have unique advantages in regulating both electrocatalytic activity and the electronic structure of non-precious metal materials. Developing a simple and practical preparation strategy is critical, but it still faces challenges. In this paper, a novel type of dual-modification approach is put forward to rationally design the S, Pt-CoNi material, which can be grown directly on the nickel foam (NF) in a one-step electrodeposition process. The multiple advantages of having plenty of active sites, high conductivity, and a faster charge transfer endow the optimized reaction kinetic for HER. The prepared S, Pt-CoNi/NF catalyst displays excellent catalytic performance, and a low overpotential of 116 mV at 50 mA cm−2 and a small Tafel slope of 75 mV dec−1 are achieved. The coupled S, Pt-CoNi/NF||FeOOH/NF electrolyzer delivers a high current density of 100 mA cm−2 at the potential of 1.61 V as well as superior stability under alkaline conditions. Our work experimentally confirms the feasibility of constructing a dual-regulation strategy via one-step electrodeposition, and it also provides ideas for the controllable design of other high-performance electrodes for electrocatalysis. [ABSTRACT FROM AUTHOR]

The electrolysis of water is an efficient and environmentally friendly technology for large-scale hydrogen production. However, the oxygen evolution reaction (OER) involves a multi-electron–proton coupling transfer step that limits the efficiency of water splitting. Therefore, there is an urgent need to develop electrocatalysts with expected activity and stability to accelerate the kinetics of the oxygen evolution reaction. In this paper, hierarchically porous Cu(OH)2@(Fe, Co, Ni)MOF/CF nanosheet (denoted as Cu(OH)2@FCN MOF/CF) arrays were successfully prepared by the hydrothermally induced in situ growth of FCN MOF nanosheets using modified Cu(OH)2 nanowires as carriers; herein, the tuned active species of metal ligands in the FCN MOF composition structure are used as the main catalytic reaction size in the OER. The synergistic effect of a unique porous structure and the active metal-ligand species in the MOF render the catalyst a large electrochemically active surface area and more active species. Then, the active material is fully contacted with the electrolyte to expose more electrochemically active sites, thus greatly improving the electrocatalytic activity and durability of the OER. Specifically, the Cu(OH)2@FCN MOF/CF delivers a minimum overpotential of 290 mV and low Tafel slope of 96.15 mV·dec−1 at 10 mA·cm−2 as well as ultra-long cycling stability. The resulted OER performance is superior to most reported MOF-based electrocatalysts. This novel structural design not only provides a new strategy for the facile preparation of low-cost and high-efficiency OER electrocatalysts but also paves an avenue for the development of other MOF-based composite electrocatalysts with excellent electrocatalytic performances. [ABSTRACT FROM AUTHOR]

Environmental issues related to greenhouse gases (GHG) emissions have pushed the development of new technologies that will allow the economic production of low-carbon energy vectors, such as hydrogen (H2), methane (CH4) and liquid fuels. Dry reforming of methane (DRM) has gained increased attention since it uses CH4 and carbon dioxide (CO2), which are two main greenhouse gases (GHG), as feedstock for the production of syngas, which is a mixture of H2 and carbon monoxide (CO) and can be used as a building block for the production of fuels. Since H2 has been identified as a key enabler of the energy transition, a lot of studies have aimed to benefit from the environmental advantages of DRM and to use it as a pathway for a sustainable H2 production. However, there are several challenges related to this process and to its use for H2 production, such as catalyst deactivation and the low H2/CO ratio of the syngas produced, which is usually below 1.0. This paper presents the recent advances in the catalyst development for H2 production via DRM, the processes that could be combined with DRM to overcome these challenges and the current industrial processes using DRM. The objective is to assess in which conditions DRM could be used for H2 production and the gaps in literature data preventing better evaluation of the environmental and economic potential of this process. [ABSTRACT FROM AUTHOR]

With the final purpose of manufacturing electrochemically-based devices that produce chloride dioxide efficiently, this paper focuses on the production of chlorates and hydrogen peroxide in two different electrochemical cells, in which operation conditions are selected to obtain high efficiencies, and in the subsequent combination of both electrochemically manufactured solutions to produce chlorine dioxide. Results demonstrate that suitable reagents can be produced by electrolyzing 20 g L−1 sodium chloride solutions at 50 mA cm−2 and 50 °C, and 3000 mg L−1 NaClO4 solutions at 5.0 mA cm−2 and 15 °C with current efficiencies of 30.9% and 48.0%, respectively. Different tests performed with these electrolyzed solutions, and also with commercial hydrogen peroxide and chlorate solutions, demonstrate that the ratio between both reagents plays a very important role in the efficiency in the production of chlorine dioxide. Results clearly showed that, surplus chlorate should be contained in the reagent media to prevent further reduction of chlorine dioxide by hydrogen peroxide and consequently, loses of efficiency in the process. During the reaction, a gas with a high oxidation capacity and consisting mainly in chloride dioxide is produced. The results contributed to the maximum conversion reached being 89.65% using electrolyzed solutions as precursors of ClO2, confirming that this technology can be promising to manufacture portable ClO2 devices. [ABSTRACT FROM AUTHOR]

In this study, original titanium dioxide (TiO2) and cerium (Ce)-doped TiO2 nanorod array photoanodes are prepared by hydrothermal method combined with high-temperature annealing, and their morphology, photoelectrochemical properties, and photocatalytic hydrogen production ability are systematically evaluated. X-ray diffraction (XRD) analysis shows that as the Ce content increases, the diffraction peak of the rutile phase (110) shifts towards lower angles, indicating the successful doping of different contents of Ce into the TiO2 lattice. Photoelectric performance test results show that Ce doping significantly improves the photocurrent density of TiO2, especially for the 0.54wt% Ce-doped TiO2 (denoted as CR5). The photocurrent density of CR5 reaches 1.98 mA/cm2 at a bias voltage of 1.23 V (relative to RHE), which is 2.6 times that of undoped TiO2 (denoted as R). Photoelectrochemical hydrolysis test results show that the hydrogen yield performance under full-spectrum testing conditions of Ce-doped TiO2 photoanodes is better than that of original TiO2 as well, which are 37.03 and 12.64 µmol·cm−2·h−1 for CR5 and R, respectively. These results indicate that Ce doping can effectively promote charge separation and improve hydrogen production efficiency by reducing resistance, accelerating charge transfer, and introducing new electronic energy levels. Our findings provide a new strategy for designing efficient photocatalysts with enhanced photoelectrochemical (PEC) water-splitting performance. [ABSTRACT FROM AUTHOR]

A key research focus at present is the exploration and innovation of electrode materials suitable for energy storage and conversion. Molybdenum-based sulfides/selenides (primarily MoS2 and MoSe2) have garnered attention in recent years due to their intrinsic two-dimensional structures, which are conducive to ion/electron transfer or insertion/extraction, making them promising candidates in electrocatalytic hydrogen production and sodium-ion battery applications. However, their inherently poor electronic structures have led most research efforts to concentrate on modifications aimed at enhancing their performance in hydrogen evolution reactions (HERs) and sodium-ion batteries (SIBs). Owing to their remarkable chemical inertness, expansive specific surface areas, and tunable pore architectures, carbon-based materials have garnered significant attention in research. The utilization of biomass as a renewable and environmentally sustainable precursor offers considerable benefits, including abundant availability, ecological compatibility, and cost-effectiveness. Consequently, recent scholarly endeavors have concentrated intensively on the synthesis of valuable carbon materials derived from renewable biomass sources. This review addresses the scientific challenges related to the development of electrode materials for HERs and SIBs in electrochemical energy storage and conversion. It delves into the recent focus on the two-dimensional transition-metal chalcogenides, particularly MoS2 and MoSe2, and the difficulties encountered in modulating their electronic structures when applied to HERs and SIBs. The review proposes the use of eco-friendly and widely sourced biomass-derived carbon (BMC) as a supporting matrix combined with MoS2 and MoSe2 to regulate their structures and enhance their electrocatalytic activity and sodium storage performance. Additionally, it highlights the existing challenges faced by these BMC/MoS2 and BMC/MoSe2 composites and offers insights into future developments. [ABSTRACT FROM AUTHOR]

ZnIn2S4 has attracted extensive attention in the field of photocatalytic hydrogen production because of its suitable band gap and excellent photoelectrochemical properties. However, its lower photogenerated carrier separation efficiency and high degree of photocorrosion severely restricts its photocatalytic activity. In this work, the photocatalytic hydrogen production performance of ZnIn2S4 modified with 3-aminopropylmethoxysilane was studied. Surface modification by amino silane not only regulated the band gap and enhanced the light absorption of ZnIn2S4 but it also increased the colloidal stability of the ZnIn2S4 suspension and enhanced the adsorption of H+ on the active surface sites, thereby improving the photocatalytic hydrogen production performance. Compared with that of unmodified ZnIn2S4, the photocatalytic hydrogen production rate of surface-modified ZnIn2S4 increased by 1.46 times, and after four cycles for 12 h, the hydrogen production efficiency remained at 75.14%. [ABSTRACT FROM AUTHOR]

This paper describes the synthesis of a series of La1.4Sr0.6Ni1-xCoxO4 perovskite OCs using co-precipitation method by employing Co and Ni as the B-site components of perovskite and the synergetic effect of Co doping on chemical looping reforming of ethanol. A variety of techniques including N2 adsorption-desorption, X-ray diffraction (XRD), transmission electron microscopy (TEM) and H2 temperature-programmed reduction (TPR) were employed to investigate the physicochemical properties of the fresh and used OCs. The activity and stability in chemical looping reforming were studied in a fixed bed reactor at 600 °C and a S/C ratio of three. The synergetic effect between Ni and Co was able to enhance the catalytic activity and improve the stability of perovskite OCs. La1.4Sr0.6Ni0.6Co0.4O4 showed an average ethanol conversion of 92.4% and an average CO2/CO ratio of 5.4 in a 30-cycle stability test. Significantly, the H2 yield and purity reached 11 wt.% and 73%, respectively. The Co doping was able to significantly improve the self-regeneration capability due to the increase in the number of oxygen vacancies in the perovskite lattice, thereby enhancing the sintering resistance. Moreover, Co promotion also contributes to the improved WGS activity. [ABSTRACT FROM AUTHOR]

In this paper, the structure of Al2O3 is modified with magnesium to synthesize MgAl2O4 as an oxygen carrier (OC) support. The surface properties and structural stability of the modified support are improved by the incorporation of magnesium in the structure of the support and additionally by narrowing the pore size distribution (about 2.3 nm). Then, iron oxide is impregnated on both an Al2O3 support and a MgAl2O4 support as the oxygen transfer active site. The XRD results showed the formation of solely Fe2O3 on the MgAl2O4 support, while both Fe2O3 and Fe3O4 are detected in the synthesized Fe2O3-Al2O3 structure. The synthesized samples are investigated in chemical looping cycles, including CO reduction (as one of the most important side reactions of chemical looping reforming), at different temperatures (300-500 °C) and oxidation with steam at 700 °C for hydrogen production. The obtained results showed the inhibition of Fe-Al spinel formation in the structure of the Fe2O3-MgAl2O4 OC. In addition, H2 with a purity higher than 98% is achievable in oxidation of the OC with steam. In addition, the activity and crystalline change of the Fe2O3-MgAl2O4 OC is investigated after 20 reduction-oxidation cycles. [ABSTRACT FROM AUTHOR]

Photocatalytic processes offer promising solutions for environmental remediation and clean energy production, yet their efficiency under the visible light spectrum remains a significant challenge. Here, we report a novel silver–graphene (Ag-G) modified TiO2 (Ag-G-TiO2) nanocomposite photocatalyst that demonstrates remarkably enhanced photocatalytic activity for both dye wastewater degradation and hydrogen production under visible and UV light irradiation. Through comprehensive characterization and performance analysis, we reveal that the Ag-G modification narrows the TiO2 bandgap from 3.12 eV to 1.79 eV, enabling efficient visible light absorption. The nanocomposite achieves a peak hydrogen production rate of 191 μmolesg−1h−1 in deionized (DI) water dye solution under visible light, significantly outperforming unmodified TiO2. Intriguingly, we observe an inverse relationship between dye degradation efficiency and hydrogen production rates in dye solutions with tap water versus DI water, highlighting the critical role of water composition in photocatalytic processes. This work not only advances the understanding of fundamental photocatalytic mechanisms but also presents a promising photocatalyst for solar-driven environmental remediation and clean energy production. The Ag-G-TiO2 nanocomposite's enhanced performance across both visible and UV spectra, coupled with its dual functionality in dye degradation and hydrogen evolution, represents a significant step towards addressing critical challenges in water treatment and sustainable energy generation. Our findings highlight the complex interplay between light absorption and reaction conditions, offering new insights for optimizing photocatalytic systems. This research paves the way for developing more efficient and versatile photocatalysts, potentially contributing to the global transition towards sustainable technologies and circular economy in waste management and energy production. [ABSTRACT FROM AUTHOR]

Designing g-C3N4-based nanostructured photocatalysts is crucial to boosting their application in advancing clean energy and sustainable environmental solutions. In this study, cyano groups and amorphous carbon self-modified P-doped g-C3N4 (PCNx) photocatalysts were designed and prepared by one-pot calcination. Melamine phosphate was employed as a multifunctional precursor to simultaneously achieve P-doping and amorphous carbon/cyano group self-modification in the g-C3N4 photocatalyst. The molar ratio of urea to melamine phosphate regulates the content of amorphous carbon and cyano groups, which further enhances the conductivity of g-C3N4. Due to the high conductivity of amorphous carbon and cyano groups, the charge transfer process was further accelerated. As a result, the optimized P-doping and amorphous carbon/cyano-group in PCN2 photocatalyst led to an excellent H2 production rate of 157.86 µmol·g−1·h−1 under visible light, which is approximately 2.4 times and 3 times higher than those of CN and PCN. The work developed an alternative strategy for the construction of highly efficient g-C3N4-based photocatalysts. [ABSTRACT FROM AUTHOR]

The electrocatalytic oxidation of urea combined with wastewater splitting is considered a promising approach for sustainable hydrogen production, characterized by minimal energy consumption. However, its evolution is greatly hindered by the shortage of efficient and easily accessible electrocatalytic materials. Here, a facile electrochemical activation strategy was conceived and proposed to construct a Cu-doped NiOOH nanolayer encapsulated on Cu2O nanodendrites on Cu mesh substrate (Cu-NiOOH/Cu2O/CM) from the electrodeposited Ni/Cu2O/CM heterostructured precatalyst. It was verified that the incorporation of Cu not only facilitates the rapid formation of Ni(III) species but also contributes to the formation of Cu-Ni(III) bifunctional electrocatalytic active sites. Benefiting from the accessible Cu-Ni(III) dual active sites, high active surface area, good hydrophilic and aerophobic surface properties and superior electrical conductivity of the Cu mesh substrate, the as-prepared Cu-NiOOH/Cu2O/CM exhibits enhanced bifunctional electrocatalytic abilities for electrocatalytic urea oxidation reaction (UOR) and hydrogen evolution reaction (HER). Particularly, for the Cu-NiOOH/Cu2O/CM||Cu-NiOOH/Cu2O/CM configuration toward the UOR||HER coupled system, a significantly reduced cell voltage of 1.43 V vs. RHE @ 10 mA·cm−2 was obtained. The observed cell voltage for the conventional overall water splitting is approximately 190 mV higher than that observed for overall urea splitting. This study proposes a viable approach to achieve and optimize the bifunctional UOR/HER performance of NiOOH active species, which holds significant importance for efficient and stable hydrogen generation from urea-contaminated substandard water. [ABSTRACT FROM AUTHOR]

The formation of heterojunctions for efficient charge separation has been practiced for the preparation of efficient semiconductor-based photocatalysts for applications such as hydrogen production and environmental remediation. In this study, we synthesized a composite structure with a heterojunction between SnS2 and TiO2 through a microwave-assisted hydrothermal process, in which SnS2 nanoparticles grew on nanocrystalline TiO2 nanosheets preferentially at the exposed {101} facets. Appropriate exposure of the {001} and {101} facets of the TiO2 nanosheet in the composite with a preferential growth of SnS2 nanoparticles at the {101} facets was the origin of the charge separation following a direct Z-scheme mechanism to result in enhanced photocatalytic performances in photodegradation of organic dyes such as methylene blue (MB) and rhodamine B (RhB) compared to that of SnS2 and TiO2 alone. A plot of photodegradation rates vs. SnS2 ratios in the composites gave an overall volcano-shaped curve with a maximum at the SnS2 ratio of about 33% at which small SnS2 nanoparticles were populated at the {101} facets of the TiO2 nanosheets with a high surface area (118.2 m2g−1). Our results suggest the microwave-assisted hydrothermal process can be a good synthetic approach for composite-based photocatalysts with a preferential heterojunction structure. [ABSTRACT FROM AUTHOR]

The production of H2 from renewable sources represents a crucial challenge for the planet's future to achieve net zero emissions and store renewable energy. A possible alternative to water electrolysis (WE), which requires high potential (E > 1.48 V) to trigger the oxygen evolution reaction (OER), would be alcohol electrochemical reforming (ER), which implies the oxidation of short organic molecules such as methanol or ethanol. In ER, energy must be supplied to the system, but from a thermodynamic point of view, the energy request for the methanol or ethanol oxidation reaction is much lower than that of the OER. To study this process, an in-house 50 wt.% Pt1Ru1/C anodic catalyst was easily synthesized according to the Pt sulphite complex route and the impregnation of a carbon support (Ketjenblack, KB) and a Ru precursor. X-ray diffraction (XRD), X-ray fluorescence (XRF) spectroscopy, and Transmission Electron Microscopy (TEM) were used to characterize the structure, composition, and morphology of the catalyst. It appears that two distinct crystallographic phases of the Pt and Ru nanoparticles were encountered after the synthesis conducted by Ru impregnation. For the electrochemical measurements, ethanol electrooxidation (2 M CH3CH2OH) was studied first in a half cell with a rotating disc electrode (RDE) configuration under acid conditions and then in a direct ethanol electroreforming (or electrolysis) cell, equipped with a proton exchange membrane (PEM) as the electrolyte. The output current density was 0.93 A cm−2 at 1 V and 90 °C in 2 M ethanol. The remarkable current densities obtained in the alcohol electrolyzer at a low voltage are better than the actual state of the art for PEM ethanol ER. [ABSTRACT FROM AUTHOR]

To investigate the influence of Ag and the loading of Ni species, Ni-Ag type catalysts were synthesized with varying Ni/Ag ratios (1, 1.5 and 2) using the coprecipitation method. The catalysts were extensively characterized using various techniques such as TG-DSC-SM, XRD, ICP, BET, SEM-EDX and TPR and subsequently tested in the CH4/CO2 reaction without any pretreatment. Regardless of the ratio employed, a phase mixture containing NiO and Ag was observed after calcination under air between 600 °C and 1200 °C. SEM analysis confirmed the presence of a close interface between Ag and NiO. The specific surface area was found to be significantly higher for the catalyst with lower Ni content (R = 1). TPR analysis demonstrated that the inclusion of Ag facilitated the reduction of Ni at lower temperatures. XRD analyses of the spent catalyst confirmed catalyst reduction during the reaction. Among the samples, a catalyst with Ni/Ag = 1 exhibited superior catalytic activity without any pretreatment under a reduction atmosphere, in which case the conversions of methane and CO2 at 650 °C amounted to 38 and 45 mol%, respectively, with H2/CO = 0.7 and 71 mol% of H2. The presence of Ag species enhances the stability of the Ni catalyst and improves catalytic performance in the dry reforming of methane. [ABSTRACT FROM AUTHOR]

This study presents the successful synthesis of a cesium–nickel–vanadium fluoride (CsNiVF6) pyrochlore nano-sheet catalyst via solid-phase synthesis and its electrochemical performance in green hydrogen production through urea electrolysis in alkaline media. The physicochemical characterizations revealed that the CsNiVF6 exhibits a pyrochlore-type structure consisting of a disordered cubic corner-shared (Ni, V)F6 octahedra structure and nano-sheet morphology with a thickness ranging from 10 to 20 nm. Using the CsNiVF6 catalyst, the electrochemical analysis, conducted through cyclic voltammetry, demonstrates a current mass activity of ~1500 mA mg−1, recorded at 1.8 V vs. RHE, along with low-resistance (3.25 ohm) charge transfer and good long-term stability for 0.33 M urea oxidation in an alkaline solution. Moreover, the volumetric hydrogen production rate at the cathode (bare nickel foam) is increased from 12.25 to 39.15 µmol/min upon the addition of 0.33 M urea to a 1.0 KOH solution and at a bias potential of 2.0 V. The addition of urea to the electrolyte solution enhances hydrogen production at the cathode, especially at lower voltages, surpassing the volumes produced in pure 1.0 M KOH solution. This utilization of a CsNiVF6 pyrochlore nano-sheet catalyst and renewable urea as a feedstock contributes to the development of a green and sustainable hydrogen economy. Overall, this research underscores the potential use of CsNiVF6 as a cost-effective nickel-based pyrochlore electrocatalyst for advancing renewable and sustainable urea electrolysis processes toward green hydrogen production. [ABSTRACT FROM AUTHOR]

The manipulation of trap states plays a crucial role in the development of efficient photocatalysts. An ultrathin-shelled Zn-AgIn5S8/ZnS quantum dots (QDs) photocatalyst was synthesized via in situ growth using a low-temperature hydrothermal method. The optical properties of the samples coated with ZnS shell were studied vis UV-vis absorption and fluorescence spectra. The ultrathin ZnS shell plays an important role in the Zn-AgIn5S8/ZnS core–shell heterostructure photocatalytic water splitting system, which could reduce surface defects, prolong the carrier lifetime and improve the photo-generated electron–hole pair separation effectively, resulting in the improved photocatalytic efficiency and enhanced stability of the catalyst. The results provide an effective guideline for shell thickness design in future constructions of the core–shell heterostructure photocatalyst. [ABSTRACT FROM AUTHOR]

Water splitting is widely acknowledged as an efficient method for hydrogen production. In recent years, significant research efforts have been directed towards developing cost-effective electrocatalysts. However, the management of bubbles formed on the electrode surface during electrolysis has been largely overlooked. These bubbles can impede the active sites, resulting in decreased catalytic performance and stability, especially at high current densities. Consequently, this impediment affects the energy conversion efficiency of water splitting. To address these challenges, this review offers a comprehensive overview of advanced strategies aimed at improving catalytic performance and mitigating the obstructive effects of bubbles in water splitting. These strategies primarily involve the utilization of experimental apparatus to observe bubble-growth behavior, encompassing nucleation, growth, and detachment stages. Moreover, the review examines factors influencing bubble formation, considering both mechanical behaviors and internal factors. Additionally, the design of efficient water-splitting catalysts is discussed, focusing on modifying electrode-surface characteristics. Finally, the review concludes by summarizing the potential of bubble management in large-scale industrial hydrogen production and identifying future directions for achieving efficient hydrogen production. [ABSTRACT FROM AUTHOR]

In this work, the WGS performance of a conventional Ni/CeO2 bulk catalyst is compared to that of a carbon-supported Ni-CeO2 catalyst. The carbon-supported sample resulted to be much more active than the bulk one. The higher activity of the Ni-CeO2/C catalyst is associated to its oxygen storage capacity, a parameter that strongly influences the WGS behavior. The stability of the carbon-supported catalyst under realistic operation conditions is also a subject of this paper. In summary, our study represents an approach towards a new generation of Ni-ceria based catalyst for the pure hydrogen production via WGS. The dispersion of ceria nanoparticles on an activated carbon support drives to improved catalytic skills with a considerable reduction of the amount of ceria in the catalyst formulation. [ABSTRACT FROM AUTHOR]

In the last decades, environmental crises and increasing energy demand have motivated researchers to investigate the practical techniques for the production of clean fuels through renewable energy resources. It is essential to develop technologies to utilize glycerol as a byproduct derived from biodiesel. Glycerol is known as a sustainable and clean source of energy, which can be an alternative resource for the production of value-added chemicals and hydrogen. The hydrogen production via steam reforming (SR) of glycerol using Ni-based catalysts is one of the promising approaches for the entry of the hydrogen economy. The purpose of this review paper is to highlight the recent trends in hydrogen production over Ni-based catalysts using the SR of glycerol. The intrinsic ability of Ni to disperse easily over variable supports makes it a more viable active phase for the SR catalysts. The optimal reaction conditions have been indicated as 650–900 °C, 1 bar, and 15 wt% Ni in catalysts for high glycerol conversion. In this review paper, the effects of various supports, different promoters (K, Ca, Sr, Ce, La, Cr, Fe), and process conditions on the catalytic performance have been summarized and discussed to provide a better comparison for the future works. It was found that Ce, Mg, and La have a significant effect on catalytic performance as promoters. Moreover, SR of glycerol over hydrotalcite and perovskite-based catalysts have been reviewed as they suggest high catalytic performance in SR of glycerol with improved thermal stability and coke resistance. More specifically, the Ni/LaNi0.9Cu0.1O3 synthesized using perovskite-type supports has shown high glycerol conversion and sufficient hydrogen selectivity at low temperatures. On the other hand, hydrotalcite-like catalysts have shown higher catalytic stability due to high thermal stability and low coke formation. It is vital to notice that the primary concern is developing a high-performance catalyst to utilize crude glycerol efficiently. [ABSTRACT FROM AUTHOR]

Herein, Ir/CeO2 catalysts were prepared using the deposition–precipitation method with NaOH or urea as the precipitating agent or using sol immobilization with tetrakis(hydroxymethyl)phosphonium chloride (THPC) as the protective and reducing agent. The effect of the preparation method on Ir catalyst activity was evaluated in the liquid-phase catalytic decomposition of hydrous hydrazine to hydrogen. Ir/CeO2 prepared using sol immobilization and DP NaOH showed the best activity (1740 h−1 and 1541 h−1, respectively) and yield of hydrogen (36.6 and 38.9%). Additionally, the effect of the support was considered, using TiO2 and NiO in addition to CeO2. For this purpose, the sol immobilization of preformed nanoparticles technique was considered because it allows the same morphology of the immobilized particles to be maintained, regardless of the support. Ir deposited on NiO resulted in the most selective catalyst with a H2 yield of 83.9%, showing good stability during recycling tests. The catalysts were characterized using different techniques: X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM) equipped with an X-ray detector (EDX) and inductively coupled plasma–mass spectroscopy (ICP-MS). [ABSTRACT FROM AUTHOR]

Tandem photoelectrochemical cells (PECs) are devices useful for water splitting (WS) with the production of oxygen at the photoanode (PA) and hydrogen at the photocathode (PC) by adsorbing more than 75% of the solar irradiation; a portion of the UV/Vis direct solar irradiation is captured by the PA and a diffused or transmitted IR/Vis portion by the PC. Herein, Ti-doped hematite (PA) and CuO (PC) were employed as abundant and non-critical raw semiconductors characterised by proper band gap and band edge banding for the photoelectrochemical WS and absorption of sunlight. The investigation of inexpensive PEC was focused on the scalability of an active area from 0.25 cm2 to 40 cm2 with a rectangular or square shape. For the first time, this study introduces the novel concept of a glass electrode membrane assembly (GEMA), which was developed with an ionomeric glue to improve the interfacial contact between the membrane and photoelectrodes. On a large scale, the electron–hole recombination and the non-optimal photoelectrodes/electrolyte interface were optimized by inserting a glass support at the photocathode and drilled fluorine tin oxide (FTO) at the photoanode to ensure the flow of reagents and products. Rectangular 40 cm2 PEC showed a larger maximum enthalpy efficiency of 0.6% compared to the square PEC, which had a value of 0.37% at a low bias-assisted voltage (−0.6 V). Furthermore, throughput efficiency reached a maximum value of 1.2% and 0.8%, demonstrating either an important effect of the PEC geometries or a non-significant variation of the photocurrent within the scalability. [ABSTRACT FROM AUTHOR]

Hydrogen production from natural gas or biogas, at different purity levels, has emerged as an important technology with continuous development and improvement in order to stand for sustainable and clean energy. Regarding biogas, which can be obtained from multiple sources, hydrogen production through the steam reforming of methane is one of the most important methods for its energy use. In that sense, the role of catalysts to make the process more efficient is crucial, normally contributing to a higher hydrogen yield under milder reaction conditions in the final product. The aim of this review is to cover the main points related to these catalysts, as every aspect counts and has an influence on the use of these catalysts during this specific process (from the feedstocks used for biogas production or the biodigestion process to the purification of the hydrogen produced). Thus, a thorough review of hydrogen production through biogas steam reforming was carried out, with a special emphasis on the influence of different variables on its catalytic performance. Also, the most common catalysts used in this process, as well as the main deactivation mechanisms and their possible solutions are included, supported by the most recent studies about these subjects. [ABSTRACT FROM AUTHOR]

Proton exchange membrane (PEM) water electrolysis for hydrogen production has a high current density and overall efficiency, and is a very promising hydrogen production strategy. However, its application is limited by the high anodic overpotential for oxygen evolution and the instability of catalysts. Therefore, anodic catalysts with a high activity and durability under acidic conditions need further research. Herein, we first synthesized the key intermediate Ru@Ir core-shell structures by controlling nanocrystals, then loaded them onto a carbon support and calcined to obtain a RuO2@IrO2/C core-shell nanocatalyst with a size smaller than 5 nm, whose activity exceeded that of commercial RuO2 and commercial IrO2. After a 200 h stability test, the catalyst did not show significant performance degradation or structural degeneration. Finally, the prepared catalyst was assembled into a PEM electrolyzer showing the same results as the three-electrode tests, demonstrating its potential for practical applications and providing new insights for designing nanocatalysts suitable for industrialized PEM water electrolysis to produce hydrogen [ABSTRACT FROM AUTHOR]

This document discusses the development of novel photo(electro)catalysts for energy and environmental applications. It includes eleven articles that cover various topics such as photodegradation of organic matter, hydrogen production, and purification of volatile organic compounds. The articles highlight the synthesis and performance of different catalysts, including Fe-doped perovskite-type PbBi2Nb2O9, NiSe2/Ag3PO4 composites, Fe2O3/C heterojunction-based rape pollen, nitrogen-doped TiO2@SiO2 core/shell photocatalyst, and more. The document also explores the use of photocatalytic and photoelectrocatalytic processes for water splitting and the production of hydrogen and biodiesel. [Extracted from the article]

Hydrogen from biomass, as a promising alternative fuel, is becoming considerably attractive due to its high energy density and clean emissions. The aqueous phase reforming (APR) of biomass-derived oxygenated hydrocarbons and water is a renewable and efficient pathway for hydrogen production and shows great potential. However, the key to the application of this technique is to develop catalysts with high hydrogen productivity. In this work, we first synthesized polyaniline–platinum (PANI-Pt) organo-metallic hybrid precursors and then obtained a high-loaded (~32 wt.% Pt) and highly dispersed (~3 nm Pt particles) Pt@NC−400 catalyst after pyrolysis at 400 °C, and the nanoparticles were embedded in a nitrogen-doped carbon (NC) support. The Pt@NC−400 catalyst showed an almost three times higher hydrogen production rate (1013.4 μmolH2/gcat./s) than the commercial 20% Pt/C catalyst (357.3 μmolH2/gcat./s) for catalyzing methanol–water reforming at 210 °C. The hydrogen production rate of 1,2-propanediol APR even reached 1766.5 μmolH2/gcat./s over the Pt@NC−400 catalyst at 210 °C. In addition, Pt@NC−400 also exhibited better hydrothermal stability than 20% Pt/C. A series of characterizations, including ICP, XRD, TEM, SEM, XPS, N2 physisorption, and CO chemisorption, were conducted to explore the physiochemical properties of these catalysts and found that Pt@NC−400, although with higher loading than 20% Pt/C (~23 wt.% Pt, ~4.5 nm Pt particle), possessed a smaller particle size, a more uniform particle distribution, a better pore structure, and more Pt metal active sites. This study provides a strategy for preparing high-loaded and highly dispersed nanoparticle catalysts with high hydrogen productivity and sheds light on the design of stable and efficient APR catalysts. [ABSTRACT FROM AUTHOR]

Hydrogen energy is a plentiful and environmentally friendly form of secondary energy that could play a crucial role in achieving global energy sustainability. At the same time, the electrolysis of water for hydrogen production is a significant future-oriented advancement in the energy sector, whereas appropriate hydrogen evolution catalysts have always been the key to hydrogen evolution reactions. In this study, lignin was utilized as an appropriate raw material for modification in order to obtain carbon materials, which was then supported with Ru to prepare an Ru0.8@MLC catalyst. At a current density of 10 mA cm−2, the required overpotential was a mere 35.6 mV and the slope of Tafel was 31.7 mV dec−1. This study provides a feasible strategy and pathway for preparing highly efficient electrocatalysts for the hydrogen evolution reaction. [ABSTRACT FROM AUTHOR]

Electrocatalytic and photocatalytic hydrogen evolution reactions (HERs) provide a promising approach to clean energy generation. Bimetallic single-atom catalysts have been developed and explored to be advanced catalysts for HER. It is urgent to review and summarize the recent advances in developing bimetallic single-atom HER catalysts. Firstly, the fundamentals of bimetallic single-atom catalysts are presented, highlighting their unique configuration of two isolated metal atoms on their supports and resultant synergistic effects. Secondly, recent advances in bimetallic single-atom catalysts for electrocatalytic HER under acidic/alkaline conditions are then reviewed, including W-Mo, Ru-Bi, Ni-Fe, Co-Ag, and other dual-atom systems on graphene and transition metal dichalcogenides (TMDs) with enhanced HER activity versus monometallic analogs due to geometric and electronic synergies. Then, photocatalytic bimetallic single-atom catalysts on semiconducting carbon nitrides for solar H2 production are also discussed. Finally, an outlook is provided on opportunities and challenges in precisely controlling bimetallic single-atom catalyst synthesis and gaining in-depth mechanistic insights into bimetallic interactions. Further mechanistic and synthetic studies on bimetallic single-atom catalysts will be imperative for developing optimal systems for efficient and sustainable hydrogen production. [ABSTRACT FROM AUTHOR]

Given that the attempts to head toward a hydrogen economy are gathering pace, the dry reforming of methane (DRM) to produce hydrogen-rich syngas is a reaction that is worthy of investigation. Nickel-based catalysts have been extensively examined as a cost-effective solution for DRM, though they suffer from fast deactivation caused by coke accumulation. However, a number of published studies report high catalytic performance in terms of both activity and stability for La–Ni-based perovskite-derived catalysts used in DRM in comparison to other corresponding materials. In the work presented herein, a thorough analysis regarding the application of La–Ni-based perovskite catalysts for DRM is carried out. LaNiO3 is known for its anti-coking ability owing to the strong interaction between CO2 and La2O3. A further modification to improve the catalytic performance can be achieved by the partial or complete substitution of A or/and B sites of the perovskite catalysts. The latest developments with respect to this topic are also discussed in this manuscript. Even though the low surface area of perovskite catalysts has always been an obstacle for their commercialization, new supported and porous perovskite materials have recently emerged to address, at least partly, the challenge. Finally, conclusions and future outlooks for developing novel perovskite catalysts that may potentially pioneer new technology are included. [ABSTRACT FROM AUTHOR]

The proton exchange membrane water electrolyzer (PEM-WE) is a well-known green technology for hydrogen production. The main obstacle to its development, on a large scale, is the sluggish kinetics of the oxygen evolution reaction (OER). At present, the design of acid-stable electrocatalysts with low overpotential and excellent stability for the OER constitutes an important activity in electrocatalysis. This review presents an analysis of the fundamentals and strategies for the design of advanced electrocatalysts for oxygen evolution, reaction mechanisms, and OER descriptors. The scrutiny of OER electrocatalysts, with elemental composition from single- to multielemental, are presented. In addition, the purpose of high-entropy alloys (HEAs), a recent research strategy, for the design of advanced materials is summarized. Briefly, the effect of support materials, which are beneficial for modulating the electronic properties of catalysts, is presented. Finally, the prospects for the development of acidic OER electrocatalysts are given. [ABSTRACT FROM AUTHOR]

The oxy-steam reforming of liquefied natural gas reaction (OSR-LNG) is promising process for syngas generation. In this paper, the catalytic properties of NiO/La2O3 systems prepared by wet impregnation and co-precipitation methods were extensively investigated in OSR-LNG reaction. The physicochemical properties of the studied catalytic materials were determined using various techniques including Temperature programmed reduction (TPR-H2), Temperature programmed desorption (TPD-NH3), Brunauer, Emmett and Teller (BET), X-ray diffraction (XRD) and Scanning electron microscopy (SEM) with an energy dispersive X-Ray spectrometer (EDS). Reactivity measurements performed in the OSR-LNG process showed that the catalyst preparation method and the calcination temperature significantly affected the activity of NiO/La2O3 catalysts in the OSR-LNG reaction. The catalytic activity tests showed that NiO/La2O3 system prepared by a wet impregnation method and calcined at 700 °C showed the total conversion of the LNG component at 900 °C and the highest H2 yield at 700 and 900 °C. The phase composition studies confirmed the formation of the LaNiO3 structure in the case of the NiO/La2O3 catalyst prepared by wet impregnation, calcined at the temperature of 700 °C. Catalytic activity measurements showed that the reactivity of the catalysts was related to their phase composition and acidity. SEM images of spent catalysts showed that the smallest amount of carbon deposit was detected on the surface of the most active systems. [ABSTRACT FROM AUTHOR]

Hydrogen is a clean fuel for transportation and energy storage. The most used hydrogen storage technologies include compressed gas, cold/cryo-compression, liquid hydrogen storage, metal-organic frameworks, and metal hydrides. These include hydrogen production using fossil fuel (gray hydrogen); hydrogen production from fossil fuel combined with carbon capture, utilization, and storage (blue hydrogen); renewable energy-derived hydrogen (green hydrogen); bioproduction of hydrogen; nuclear hydrogen production; and hydrogen production as a by-product in various industries. [Extracted from the article]

The current study was performed for the experimental modeling of cyclic steam-air injection in a heavy oil reservoir model of dual porosity in the presence of a nickel-based catalyst for in situ oil upgrading enhanced by simultaneous hydrogen generation. The research was realized in the combustion tube setup with a sandpack core model under reservoir conditions due to the consistent injection of air followed by oil in situ combustion (ISC) and steam (water) injection. As a result, the original oil was upgraded regarding fractional composition and oil properties. In addition, simulated reservoir heterogeneity and cyclic stimulation intensified the hydrogen synthesis, which, in turn, could also contribute to oil upgrading. [ABSTRACT FROM AUTHOR]

Photocatalytic materials can effectively decompose water to produce hydrogen and degrade pollutants, ameliorating environmental issues. These materials are currently a popular research topic for addressing energy shortages and water pollution issues worldwide. Herein, we prepared composite catalysts with g-C3N4/rGO heterojunctions formed via the stacking of reduced graphene oxide (rGO) nanosheets and three-dimensional (3D) carbon nitride, and the catalysts displayed excellent photocatalytic activity in experiments for hydrogen production (4.37 mmol g−1 h−1) and rhodamine B elimination (96.2%). The results of structural characterization showed that the recombination of rGO has no effect on the morphology of g-C3N4, and the photochemical characterization results showed that the photogenerated electron migration of the prepared composite was accelerated. Additionally, a possible mechanism of enhancement involving synergy between the 3D structure of the catalyst and the g-C3N4/rGO heterojunctions was proposed on the basis of catalyst characterization and photocatalytic experiments. The prepared composite catalysts had large specific surface areas and abundant adsorption sites due to the 3D structure, and the g-C3N4/rGO heterojunction provided high electron mobility, resulting in low recombination of photoinduced electron and hole pairs and high conductivity. Moreover, free radical species that may play a substantial role in the photocatalytic process were analyzed via free radical quenching experiments, and possible catalytic mechanisms were presented in this study. [ABSTRACT FROM AUTHOR]

The synthesis of CaCO3/Cu2O/GO nanocomposites was developed by sol-gel auto-combustion method. The analysis of structure was completed on X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and environmental scanning electron microscopy (ESEM). The XRD spectra of the nanocomposites matched the crystal structure of CaCO3/Cu2O. The average crystal size was 20 nm for Cu2O and 25 nm for CaCO3 nanoparticles. FTIR data showed the absorption bands of Cu2O and GO. Raman spectroscopy data confirmed the formation of GO sheets. ESEM micrographs displayed spherical nanoparticles dispersed in GO sheets. X-ray photoelectron spectroscopy showed the peaks of Cu 2p, O 1s, C 1s, Cu 3s, and Ca 2p. The spectra of optical absorption revealed an absorption band of around 450 nm. The calcium content increase led to a decrease in the optical energy gap from 2.14 to 1.5 eV. The production of hydrogen from NaBH4 across the methanolysis reaction was accelerated by the CaCO3/Cu2O/GO nanocomposites. Therefore, these nanocomposites are superior in catalytic hydrogen production systems. [ABSTRACT FROM AUTHOR]

In recent years, perovskite solar cells have achieved high efficiency in small areas, but the industrialization of perovskite solar cells is still hampered by the efficiency loss of cells during area scaling. Series modules are currently the most widely used and effective modular process for perovskite solar cells, a process that requires the patterning of the layer stack in individual cells. This interconnection scheme consists of three lines, P1–P3, which are ablated using a pulsed laser beam. In this work, we developed an efficient perovskite module with a high geometric fill factor (GFF) based on a two-step spin-coating method by optimizing the laser ablation step. We constructed the entire device structure by means of a picosecond green pulsed laser, meanwhile, the dead area is greatly reduced by optimizing the parameters and process, and finally achieving an ultra-high GFF of over 99%. In addition, we investigated the effect of poor P2 and P3 ablation on the perovskite solar modules and compared the performance of the module before and after ablation optimization. We finally obtained a maximum photoelectric conversion efficiency of 22.79% with an aperture area of 12.6 cm2. Concurrently, we conducted electrocatalytic hydrogen production experiments on the prepared perovskite solar modules, and the experimental results have also shown excellent performance and good prospects. [ABSTRACT FROM AUTHOR]

The use of ammonia as a hydrogen carrier requires efficient cracking technology. A promising solution is the use of a membrane reactor (MR), which enables both ammonia decomposition and hydrogen separation to take place within the same device, providing advantages in terms of efficiency and compactness compared to conventional systems. The literature reports that ceramic-supported double-skinned Pd-Ag membranes show outstanding performance for hydrogen separation as well as good stability of the separation layer during ammonia decomposition. However, their sealing in the reactor may result in leakage increase, while their mechanical stability remains an unresolved issue. To circumvent these limitations, the use of metallic supported Pd-based membranes is recommended, due to their higher mechanical stability and ease of sealing and integration in the reactor. In this work, we propose the development of robust metallic supported hydrogen-selective membranes for integration in membrane reactors for ammonia cracking. A conventional Pd-Ag membrane was prepared on a low-cost porous Hastelloy X tubular filter, modified with α-Al2O3/γ-Al2O3 to reach the desired surface quality. The membrane was then tested for ammonia decomposition in a MR configuration, showing the ability to reach >99% NH3 conversion above 475 °C with H2 feed recovery >60%. The results achieved pave the way towards a possible substitute for the ceramic-supported alternatives. [ABSTRACT FROM AUTHOR]

In this paper, the 10 wt% Ni/Al2O3-MgO (10Ni/MA), 5 wt% Ni-5 wt% Ce/Al2O3-MgO (5Ni5Ce/MA), and 5 wt% Ni-5 wt% Co/Al2O3-MgO (5Ni5Co/MA) catalysts were prepared by an impregnation method. The effects of CeO2 and Co doping on the physicochemical properties of the Ni/Al2O3-MgO catalyst were comprehensively studied by N2 adsorption-desorption, X-ray diffraction (XRD), transmission electron microscopy (TEM), H2 temperature programmed reduction (H2-TPR), CO2 temperature programmed reduction (CO2-TPD), and thermogravimetric analysis (TGA). The effects on catalytic performance for the combined steam and CO2 reforming of methane with the low steam-to-carbon ratio (S/C ratio) were evaluated at 620 °C under atmospheric pressure. The appearance of CeO2 and Co enhanced the oxygen species at the surface that decreased the coke deposits from 17% for the Ni/MA catalyst to 11–12% for the 5Ni5Ce/MA and 5Ni5Co/MA catalysts. The oxygen vacancies in the 5Ni5Ce/MA catalyst promoted water activation and dissociation, producing surface oxygen with a relatively high H2/CO ratio (1.6). With the relatively low H2/CO ratio (1.3), the oxygen species at the surface was enhanced by CO2 activation-dissociation via the redox potential in the 5Ni5Co/MA catalyst. The improvement of H2O and CO2 dissociative adsorption allowed the 5Ni5Ce/MA and 5Ni5Co/MA catalysts to resist the carbon formation, requiring only a low amount of steam to be added. [ABSTRACT FROM AUTHOR]

Photocatalytic activity of HB2Nb3O10 perovskite nanosheets (B = Ca, Sr) has been systematically investigated in the reactions of hydrogen production, depending on the method of the photocatalyst preparation: using the pristine nanosheets in the parent suspension without reassembly, filtered nanosheets as well as nanosheets restacked by hydrochloric acid. Photocatalytic measurements were organized in such a way as to control a wide range of parameters, including the hydrogen generation rate, quantum efficiency of the reaction, potential dark activity of the sample as well as stability and pH of the reaction suspension. Exfoliation of the niobates into nanosheets allowed obtaining efficient photocatalysts surpassing the initial bulk materials in the activity up to 55 times and providing apparent quantum efficiency up to 20.8% after surface decoration with a Pt cocatalyst. Among the reassembled samples, greater hydrogen evolution activity was exhibited by simply filtered nanosheets that, unlike the HCl-restacked ones, were found to possess much lower specific surface area in a dry state but contain a perceptible amount of tetrabutylammonium cations on the surface. The activity difference, potentially, is associated with the fact that the filtered nanosheets undergo ultrasonic disaggregation before photocatalytic tests much easier than their HCl-restacked counterparts and, thanks to this, have greater active surface in the reaction suspension. In addition, the enhanced activity of the filtered nanosheets may be due to the presence of tetrabutylammonium as an organic modifier on their surface, which is consistent with the high photocatalytic performance of organically modified layered perovskites considered in our previous reports. [ABSTRACT FROM AUTHOR]

In this work, a layered double hydroxide support modified with cadmium was synthesized by a one-pot coprecipitation method. Then, it was sulfured in different percentages by a solvothermal method. Next, the samples were analyzed using various characterization techniques like XRD, DRS, FTIR, N2 physisorption, PL spectroscopy, TEM, and SEM. Finally, the synthesized and uncalcined materials were assessed in hydrogen production from water and a methanol-water solution under UV-light irradiation. The results showed that the sulphuration improves the photocatalytic activity, reaching a maximum rate constant of hydrogen production of 7403 µmol/g∙h in a methanol-water solution and 1326 µmol/g∙h in water. [ABSTRACT FROM AUTHOR]

In this study, multi-walled carbon nanotubes (MWCNTs) were prepared by chemical vapour deposition (CVD) using acetylene as a carbon source over an iron catalyst. As-prepared MWCNTs were used to support modern mono-copper, palladium, and bimetallic palladium-copper catalysts, and their feasibility for hydrogen production was tested during steam reforming of methanol (SRM) and methanol decomposition (DM). The structural characteristics of the MWCNTs were evaluated using the SEM and XRD methods. The physicochemical properties of the monometallic and bimetallic catalysts were analysed using the TPR and XRD methods. The promotion effect of palladium on methanol conversion rate and H2 productivity in the case of the copper catalysts was demonstrated. The enhanced activity of the Cu/MWCNTs after palladium promotion was due to the formation of Pd-Cu alloy compound. [ABSTRACT FROM AUTHOR]

H2 production can be used as a clean and renewable energy source for various applications, including fuel cells, internal combustion engines, and chemical production. Using nickel-based catalysts for steam reforming biomass tar presents challenges related to catalyst deactivation, poisoning, heterogeneous composition, high process temperatures, and gas impurities. To overcome these challenges, adopting a nickel-based catalyst with selected oxide support and MgO and CaO promoter is a promising approach for improving the efficiency and sustainability of steam reforming for hydrogen production. The majority of studies conducted to date have focused on the steam reforming of particular tar compounds, most commonly benzene, phenol, toluene, or naphthalene, over a range of support catalysts. However, the actual biomass tar composition is complex, and each component impacts how well steam reforming works. In this research, a multi-compound biomass tar model including phenol, toluene, naphthalene, and pyrene underwent a steam reforming process. Various types with 10 wt.% of nickel-based catalysts were generated by the co-impregnation technique, which included 90 wt.% different oxide supports (Al2O3, La2O3, and ZrO2) and 10 wt.% of combination alkaline oxide earth promoters (MgO and CaO). Thermogravimetric analysis, Brunauer–Emmett–Teller (BET) method, N2 physisorption, temperature-programmed reduction (H2-TPR), temperature-programmed desorption (CO2-TPD), and X-ray diffraction (XRD) of ni-based catalyst characterized physiochemical properties of the prepared catalyst. The reaction temperature used for steam reforming was 800 °C, an S/C ratio of 1, and a GHSV of 13,500 h−1. Ni/La2O3/MgO/CaO (NiLaMgCa) produced the most carbon to-gas conversion (86.27 mol%) and H2 yield (51.58 mol%) after 5 h of reaction compared to other catalysts tested in this study. Additionally, the filamentous carbon coke deposited on the spent catalyst of NiLaMgCa does not impact the catalyst activity. NiLaMgCa was the best catalyst compared to other catalysts investigated, exhibiting a stable and high catalytic performance in the steam reforming of gasified biomass tar. In conclusion, this study presents a novel approach by adding a combination of MgO and CaO promoters to a ni-based catalyst with various oxide supports, strengthening the metal-support interaction and improving the acid-base balance of the catalyst surface. The mesoporous structure and active phase (metallic Ni) were successfully developed. This can lead to an increase in the conversion of tar to H2 yield gas and a decrease in the production of undesired byproducts, such as CH4 and CO. [ABSTRACT FROM AUTHOR]

Pt, as a common cocatalyst, has been widely used in photocatalytic H2 evolution. However, the specific role of Pt in photocatalytic H2 evolution has not been thoroughly studied. In this paper, by employing three Pt sources with different charges (positive, negative and neutral), we systematically studied the charge effect of Pt sources on photocatalytic H2 evolution via TiO2 catalyst. According to the results of Raman, X-ray photoelectron spectroscopy (XPS), recycle experiments and photocurrent characterizations, it was found that TiO2 would produce electropositive defects during photocatalytic H2 evolution, inevitably leading to the decline of H2 production activity. Thanks to the electrostatic interaction, the electronegative Pt source not only promoted charge separation, but preferential deposited on electropositive defects, which acted as the defect repair agent, and thus resulted in the increased photocatalytic stability. This work may provide a new perspective for enhancing photocatalytic stability of hydrogen production. [ABSTRACT FROM AUTHOR]

By introducing Mg, Cu, Zn, Sn, and Mn into the synthesis processes of Ni and Al based hydrotalcite, Ni–Al layered hydrotalcite-derived catalysts with different metal compositions were prepared. In this paper, the effect of metal composition on the structure of Ni–Al layered hydrotalcite-derived catalysts is investigated, and then catalytic activities of prepared catalysts with different metal compositions on ethylene glycol aqueous-phase reforming are analyzed. The physicochemical properties of the Ni–Al layered hydrotalcite-derived catalysts were characterized by X-ray diffraction (XRD), temperature-programmed reduction (TPR), and nitrogen adsorption–desorption technology. The obtained hydrotalcite-derived catalysts were applied to the process of ethylene glycol aqueous-phase reforming (APR). The XRD results confirmed that the precursors of hydrotalcite-derived catalysts with metal compositions of Ni/Mg/Al, Ni/Cu/Al, Ni/Zn/Al, and Ni/Sn/Al had hydrotalcite crystalloid morphology. During the process of ethylene glycol aqueous phase reforming, all the catalysts showed high conversion of ethylene glycol (>90%), and the optimum hydrogen yield (73.5%) was obtained when using the catalyst with metal composition of Ni/Mg/Al at 225 °C under 2.6 MPa in nitrogen atmosphere for 2.5 h. [ABSTRACT FROM AUTHOR]

The steam reforming of methane (SRM) reaction is a significant process for efficient syngas generation and for promising distributed hydrogen production. In this work, a series of LaNiO3 oxides were prepared using the Pechini method, calcined from 600 °C to 900 °C and tested for the SRM reaction. Fresh, reduced, and used samples were characterized using STA-MS-FTIR, in situ and ex situ XRD, N2 physical adsorption, H2-TPR, TEM, TPO, and Raman. The results show that LaNiO3 begins to crystallize at about 550 °C, and the increase in calcination temperature results in the following differences in the properties of the LaNiO3 samples: larger LaNiO3 grains, smaller specific surface area, higher reduction temperature, smaller Ni0 grains reduced from the bulk phase, and stronger metal–support interaction. The maximum CH4 conversion could be achieved over LaNiO3 calcinated at 800 °C. In addition, the effect of steam-to-carbon ratio (S/C) on the performance of the SRM reaction was studied, and a S/C of 1.5 was found to be optimal for CH4 conversion. Too strong a metal–support interaction and too much unreacted steam causes a loss of catalytic activity. Finally, it was also proved using TPO and Raman that an increase in calcination temperature improves the carbon deposition resistance of the catalyst. [ABSTRACT FROM AUTHOR]

In this study, a series of A-site strontium-doped La1-xSrxCeO3-δ (x = 0.2, 0.4, 0.6, 0.8) perovskite catalysts were synthesized via the ethylenediaminetetraacetic acid (EDTA) sol-gel method for hydrogen production by methanol steam reforming. The fresh and the reduced catalysts are characterized by scanning X-ray (XRD), energy dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM) techniques. Results showed that La0.6Sr0.4CeO3-δ exhibited the best performance among the La1-xSrxCeO3-δ catalysts. The operating parameters were optimized to study the catalytic performance of La0.6Sr0.4CeO3-δ, including catalytic temperature, water–methanol ratio (W/M) and liquid hourly space velocity (LHSV). However, the excessive strontium content led to a decrease in hydrogen production amount per unit time, and the high W/M promoted the reverse water–gas shift reaction (RWGS), which resulted in a decrease in CO selectivity and an increase in CO2 selectivity. In addition, the optimal reaction parameters are as follows: reforming temperature of 700 °C; W/M of 3:1; LHSV of 20 h−1. Furthermore, the methanol conversion rate of La0.6Sr0.4CeO3-δ can reach approximately 82%, the hydrogen production can reach approximately 3.26 × 10−3 mol/g(cat)/min under the optimum reaction conditions. Furthermore, La0.6Sr0.4CeO3-δ exhibits high hydrogen selectivity (85%), which is a promising catalyst for MSR application. [ABSTRACT FROM AUTHOR]

Nowadays, heterogeneous photocatalysis for water treatment and hydrogen production are topics gaining interest for scientists and developers from different areas, such as environmental technology and material science. Most of the efforts and resources are devoted to the development of new photocatalyst materials, while the modeling and development of reaction systems allowing for upscaling the process to pilot or industrial scale are scarce. In this work, we present what is known on the upscaling of heterogeneous photocatalysis to purify water and to produce green H2. The types of reactors successfully used in water treatment plants are presented as study cases. The challenges of upscaling the photocatalysis process to produce green H2 are explored from the perspectives of (a) the adaptation of photoreactors, (b) the competitiveness of the process, and (c) safety. Throughout the text, Green Chemistry and Engineering Principles are described and discussed on how they are currently being applied to the heterogeneous photocatalysis process along with the challenges that are ahead. Lastly, the role of automation and high-throughput methods in the upscaling following the Green Principles is discussed. [ABSTRACT FROM AUTHOR]