Search

Ionic liquid modification for carbon-supported platinum (Pt/C) electrocatalysts to enhance their oxygen reduction reaction (ORR) activity has been well recognized. However, the research has only been reported on the low-Pt-loading Pt/C electrocatalysts, e.g., 20 wt%, while in practical applications, usually high-Pt-loading Pt/C electrocatalysts of 45–60 wt% are used. In this work, ionic liquid modification is systematically investigated for a Pt/C electrocatalyst with 60 wt% Pt loading for its ORR activity in the cathode in proton exchange membrane fuel cells (PEMFCs). Various adsorption amounts are studied on the catalyst surface. Different modification behavior is found. Mechanism exploration shows that the adsorption of ionic liquid mainly happens on the Pt electrocatalyst surface and in the micropores of the carbon support. The highest fuel cell power performance is achieved at an ionic liquid loading of 7 wt%, which is much higher than the 3 wt% reported for the low-Pt-loading Pt/C. [ABSTRACT FROM AUTHOR]

A proton exchange membrane fuel cell (PEMFC) is an efficient and environmentally friendly power production technology that uses hydrogen energy. The cathodic oxygen reduction electrode is a critical component in the development of PEMFC. Most techniques deposit catalyst nanoparticles in areas that are inaccessible for catalytic processes, reducing platinum utilization. The substrate used in this study was carbon paper (CP) with a self-supporting structure. First, electrochemical acidification technology was employed to modify the CP's surface, followed by nanoparticle manufacturing and fixation on the CP in a single step by electrodeposition. The Pt/C0.5V2.24CP catalyst electrode demonstrated high-quality activity in the oxygen reduction reaction (ORR), with a homogeneous particle dispersion and particle size of around 50 nm. The mass activity and electrochemical active surface area (ECSA) of the Pt/C0.5V2.24CP catalyst electrode were 1.74 and 3.98 times higher than those of the Pt/C/CP-1 electrodes made with commercial catalysts, respectively. After 5000 cycles of accelerated durability testing (ADT), the mass activity and ECSA were 1.28 times and 6.16 times more than Pt/C/CP-1. This paper successfully proved the viability of electrodepositing Pt nanoparticles on CP following acidification, and that the electrochemical acidification methods have a positive influence on improving electrode ORR activity. [ABSTRACT FROM AUTHOR]

Hydrogen peroxide is a promising substitute for fossil fuels because it produces non-hazardous by-products. In this work, a glassy carbon GC was anodized in sulphuric acid at +1.8 V to prepare the working electrode. It was utilized to investigate the oxygen reduction reaction (ORR) in a basic medium containing 0.1 M NaOH as a supporting electrolyte. The objective of this investigation was to synthesize hydrogen peroxide. X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS), linear polarization, cyclic voltammetry (CV), and rotating disk electrode voltammetry (RDE) were performed for characterization and investigation of the catalytic properties. The RDE analysis confirmed that oxygen reduction reactions followed two electrons' process at an activated GC electrode. Hence, the prepared electrode generated hydrogen peroxide from molecular oxygen at a potential of around −0.35 V vs. Ag/AgCl (sat. KCl), significantly lower than the pristine GC surface. The transfer coefficient, standard reduction potential, and standard rate constant were estimated to be 0.75, −0.27 V, and 9.5 × 10−3 cm s−1, respectively. [ABSTRACT FROM AUTHOR]

An oxygen reduction reaction (ORR) is the key half reaction of proton exchange membrane fuel cells (PEMFCs), and is highly dependent on Pt-based nanocrystals as core electrocatalysts. Despite the exceptional ORR activity from adjusting the electronic structures of surface or near-surface atoms, several serious issues, including the corrosion of carbon supports, the preferential leaching of active metal elements, the instability of surface low-coordinated atoms and the sintering/agglomeration of nanocrystals, still exist, challenging the ORR durability of developed Pt-based ORR catalysts. From the point of view of the catalyst structure design, in this review, we summarized the state-of-the-art structural regulation strategies for improving the ORR durability of Pt-based catalysts. The current limitation of Pt-based binary catalysts for ORR electrocatalysis is firstly discussed, and the detailed strategies are further classified into the optimization of supports, metal-doped alloys, core/shell structures, intermetallics and high-entropy alloys, etc. The structure–performance relationship is detailedly explained, especially emphasizing the elimination of the above restrictions. Finally, the existing challenges and future research direction are further presented, aiming at practicing the PEMFC devices of the ultradurable Pt-based catalysts. [ABSTRACT FROM AUTHOR]