Search

This article presents the results of an experimental campaign conducted on a set of four unreinforced masonry walls at full scale. The purpose of this study is to assess, using non-destructive methods, the impact of retrofitting and damage on the modal response of masonry wall systems. Each wall underwent a sequence of increasing cyclic displacements applied by an actuator at the upper end of the specimen. Modal tests based on vibrations were performed both before and after rehabilitation, as well as during the sequence of increasing displacements. It was demonstrated that frequencies can identify progressive damage when the maximum crack is about to occur, as well as the effect of wall retrofitting when mass contribution is considerable. However, the modal assurance criterion indicator (MAC) fails to properly identify a trend of decreasing correlations as progressive damage increases; instead, it is sensitive to detecting maximum crack and instability conditions. Furthermore, it was determined that the coordinated modal assurance criterion indicator (COMAC) does not identify the damage distribution as expected. However, the cumulative COMAC provides a useful tool for quick visualization and interpretation of COMAC behavior. Finally, a novel damage indicator was tested, MACVF, which improves the trend and successfully identifies the most damage-sensitive mode, especially when the maximum level of damage is reached, giving MAC values below 80%. In addition, frequency variations ranged from 70% to 110% when TRM and WWM retrofitting techniques were applied.

In the scope of this study, the strengthening of reinforced concrete beams against to shear with different types of composite materials was investigated experimentally. A total of seventeen reinforced concrete beams, one with high shear strength and sixteen with low shear strength, were fabricated. The beam with high shear strength and one of the beams with low shear strength were chosen as reference beams. The remaining fifteen beam specimens were strengthened with textile-reinforced mortar (TRM) and carbon-fiber-reinforced polymer (CFRP). While light and heavy carbon mesh were used for strengthening with TRM, unidirectional carbon textile was used for strengthening with CFRP. Other experimental parameters were the spacing of strips, the number of layers (one or two) and the way of wrapping (strip or full). Simply supported beam specimens were tested under three-point loading. Beam specimens were compared in terms of failure mode, ultimate load capacity, ductility index and energy dissipation capacity.

Sustainable solutions in the building construction industry promotes the use of innovative materials such as textile reinforced mortar (TRM) as a strengthening technique resulting in a reduced life-cycle cost. This paper presents a nonlinear finite element analysis (FEA) of TRM strengthened RC walls with cut-out openings under axial loading. FEA models were developed and validated with two experimental tests from the literature. Subsequently, a parametric study was performed to investigate the contribution of TRM in strengthening RC walls considering various opening sizes, types, numbers and orientations of window openings, and TRM strengthening configurations. The parametric study results revealed that strengthened models with smaller opening sizes had higher axial strength enhancement. Furthermore, the increase in the axial load capacities of walls with door and window openings were 34 and 26%, respectively, as compared to the corresponding control ones. TRM was more effective with a lower opening aspect ratio (Ho/Lo). In addition, confining the wall piers with U-shaped TRM jackets was the most effective configuration in improving the walls’ axial strengths with maximum enhancements of 16 and 22% as compared to the models strengthened with side-bonded sheets and strips, respectively. Finally, the axial strengths of the FEA models were also compared with the existing empirical solution and showed reasonable correlation with an average discrepancy of 15%.

Textile-reinforced mortar (TRM) is used to strengthen reinforced concrete (RC) structures using a textile and inorganic matrix. TRM is a part of textile-based composites; the basic structural behaviors, application methods, and methodologies for the extension of actual structures in TRM were studied. However, structural behavior and performance verification which depict the long-term service situation and fatigue is limited. Therefore, this study, verified the flexural behavior of TRM-strengthened beams and their fatigue performances using carbon- and alkali-resistant (AR) glass textiles through 200,000 load cycles. TRM-strengthened beams were applied to an optimization strengthening method which consisted of whether the textile was straightened. According to the test results, the strengthening efficiency of TRM-strengthened beams when subjected to cyclic loading was lower than that of the monotonic loading, except for the straightened carbon textile specimen. The average efficiency of the AR-glass textile (straightened and non-straightened) and carbon (non-straightened) was 0.86 compared to the TRM-strengthened beam subjected to monotonic loading in terms of flexural strength. In the case of deflection, the average efficiency of the AR-glass textile type was similar to the monotonic loading test results, while that of the non-straightened carbon textile was improved. The Ca-S specimen that was used to straighten the carbon textile showed a reliable structural performance with a strength efficiency of 0.99 and a deflection efficiency of 0.97 compared to the monotonic load test. Therefore, TRM strengthening using a straightened carbon textile is expected to be sufficient for the fatigue design of TRM-strengthened beams.

The formulas available in the literature for predicting the projectile impact response of reinforced concrete (RC) targets are generally developed based on the results of impact tests. Recently, however, in order to avoid performing involved and challenging projectile impact tests, the impact response of RC targets was predicted using the quasi-static punching response of RC slabs. In this paper, the concept is extended to concrete slabs strengthened with textile-reinforced mortar (TRM) or carbon fiber-reinforced polymer (CFRP) sheets externally bonded to the concrete surface. In 16 groups, 96 slabs of 600 × 600 × 90 mm size were cast and tested under quasi-static and impact loads. The slabs were reinforced with two types of reinforcement: ϕ8@100 mm and ϕ4@25 mm. The singly and doubly reinforced concrete slabs with rebar spacing of 100 mm were strengthened using externally bonded CFRP and TRM on the back side of the slab specimens. Two mixes of concrete, representing normal and high-strength concretes, were used. The results of the present study reveal that the CFRP and TRM strengthening of RC slabs enhanced the energy absorption in punching by 57–130% and 20–59%, respectively. The use of WWM in singly and doubly reinforced slabs also resulted in a 30–42% and 41–63% increase in energy absorption in punching, respectively. An earlier proposed model was modified to incorporate the influence of strengthening (CFRP and TRM) in the estimation of the projectile perforation energy of the strengthened RC slabs with the help of energy absorbed in their quasi-static punching. This perforation energy was then employed for predicting the ballistic limit of CFRP- and TRM-strengthened slabs. The predictions show good agreement with the experimentally observed ballistic limits.

Textile-Reinforced Mortar (TRM) is a modern and compatible strengthening strategy for existing masonry, which consists in plastering the walls by means of mortar layers with embedded grids or textiles made of long fibers. TRM can be very useful for the reduction of the seismic vulnerability of masonry buildings, since the fiber-based reinforcement, carrying high tensile stresses, opposes the widening of cracks and provides “pseudo-ductility” to the masonry. The increasing number of available studies on the subject testifies to its relevance but also the lack of a standardized or well-establish approach to quantify the benefits of these systems on the performance of masonry. The present review is aimed at providing a broad overview of how the study of TRM-strengthened masonry elements has been addressed in the literature. In particular, the main features of the different experimental tests are compared, dealing with both in-plane and out-of-plane behavior. Moreover, the different design methods and numerical modeling strategies are presented and discussed.

Due to inadequacies of reinforcement design in older structures and changes in building codes, but also the change of building use in existing structures, reinforced concrete (RC) beams often require upgrading during building renovation. The combined shear and flexural strengthening with composite materials, fibre-reinforced polymer sheets (FRP) and textile reinforced mortars (TRM), is assessed in this study. An experimental campaign on twelve half-scale retrofitted RC beams is presented, looking at various parameters of interest, including the effect of the steel reinforcement ratio on the retrofit effectiveness, the amount of composite material used for strengthening and the effect of the shear span, as well as the difference in effectiveness of FRP and TRM in strengthening RC beams. Significant effects on the shear capacity of composite retrofitted beams are observed for all studied parameters. The experimental study is used as a basis for developing a detailed finite element (FE) model for RC beams strengthened with FRP. The results of the FE model are compared to the experimental results and used to design a parametric study to further study the effect of the investigated parameters on the retrofit effectiveness.