Search

Molecularly imprinted polymer (MIP) nanofilms for transferrin (Trf) have been synthesized on gold surfaces by electro-polymerizing the functional monomer scopoletin in the presence of the protein target or around pre-adsorbed Trf. As determined by atomic force microscopy (AFM) the film thickness was comparable with the molecular dimension of the target. The target (re)binding properties of the electro-synthesized MIP films was evaluated by cyclic voltammetry (CV) and square wave voltammetry (SWV) through the target-binding induced permeability changes of the MIP nanofilms to the ferricyanide redox marker, as well as by surface plasmon resonance (SPR) and surface enhanced infrared absorption spectroscopy (SEIRAS) of the immobilized protein molecules. For Trf a linear concentration dependence in the lower micromolar range and an imprinting factor of ~5 was obtained by SWV and SPR. Furthermore, non-target proteins including the iron-free apo-Trf were discriminated by pronounced size and shape specificity. Whilst it is generally assumed that the rebinding of the target or of cross-reacting proteins exclusively takes place at the polymer here we considered also the interaction of the protein molecules with the underlying gold transducers. We demonstrate by SWV that adsorption of proteins suppresses the signal of the redox marker even at the bare gold surface and by SEIRAS that the treatment of the MIP with proteinase K or NaOH only partially removes the target protein. Therefore, we conclude that when interpreting binding of proteins to directly MIP-covered gold electrodes the interactions between the protein and the gold surface should also be considered., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Here we introduce microelectrospotting as a new approach for preparation of protein-selective molecularly imprinted polymer microarrays on bare gold SPR imaging chips. During electrospotting both the gold chip and the spotting tip are electrically connected to a potentiostat as working and counter electrodes, respectively. The spotting pin encloses the monomer-template protein cocktail that upon contacting the gold surface is in-situ electropolymerized resulting in surface confined polymer spots of ca. 500 µm diameter. By repeating this procedure at preprogrammed locations for various composition monomer-template mixtures microarrays of nanometer-thin surface-imprinted films are generated in a controlled manner. We show that the removal and rebinding kinetics of the template and various potential interferents to such microarrays can be monitored in real-time and multiplexed manner by SPR imaging. The proof of principle for microelectrospotting of electrically insulating surface-imprinted films is made by using scopoletin as monomer and ferritin as protein template. It is shown that microelectrospotting in combination with SPR imaging can offer a versatile platform for label-free and enhanced throughput optimization of the molecularly imprinted polymers for protein recognition and for their analytical application., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Pathogens such as viruses and bacteria use their envelope proteins and their adhesin lectins to recognize the glycan residues presented on the cell surface of the target tissues. This principle of recognition is used in a new electrochemical displacement sensor for the protein concanavalin A (ConA). A gold electrode was first modified with a self-assembled monolayer of a thiolated mannose/OEG conjugate and a ferrocene boroxol derivative was pre-assembled as reporter molecule onto the mannose surface. The novel tracer molecule based on a 2-hydroxymethyl phenyl boronic acid derivative binds even at neutral pH to the saccharides which could expand the application towards biological samples (i.e., urine and feces). Upon the binding of ConA, the tracer was displaced and washed away from the sensor surface leading to a decrease in the electrochemical signal. Using square wave voltammetry (SWV), the concentration of ConA in the sample solution could be determined in the dynamic concentration range established from 38nmolL(-1) to 5.76µmolL(-1) with a reproducible detection limit of 1µgmL(-1) (38nmolL(-1)) based on the signal-to-noise ratio (S/N=3) with fast response of 15min. The new reporter molecule showed a reduced non-specific displacement by BSA and ribonuclease A. The sensor was also successfully transferred to the first proof of principle for the detection of Escherichia coli exhibiting a detection limit of approximately 6×10(2)cells/mL. Specificity of the displacement by target protein ConA and E. coli was demonstrated since the control proteins (i.e., BSA and RNaseA) and the control E. coli strain, which lack of type 1 fimbriae, were ineffective., (Copyright © 2014 Elsevier B.V. All rights reserved.)

Microperoxidase-11 (MP-11) which has been immobilised in a matrix of chitosan-embedded gold nanoparticles on the surface of a glassy carbon electrode catalyzes the conversion of aromatic substances. This peroxide-dependent catalysis of microperoxidase has been applied in an enzyme electrode for the first time to indicate aromatic compounds such as aniline, 4-fluoroaniline, catechol and p-aminophenol. The electrode signal is generated by the cathodic reduction of the quinone or quinoneimine which is formed in the presence of both MP-11 and peroxide from the substrate. The same sensor principle will be extended to aromatic drugs., (Copyright © 2011 Elsevier B.V. All rights reserved.)

We report on the redox behaviour of the peroxygenase from Agrocybe aegerita (AaeAPO) which has been electrostatically immobilized in a matrix of chitosan-embedded gold nanoparticles on the surface of a glassy carbon electrode. AaeAPO contains a covalently bound heme-thiolate as the redox active group that exchanges directly electrons with the electrode via the gold nanoparticles. The formal potential E°' of AaeAPO in the gold nanoparticles-chitosan film was estimated to be -(286±9) mV at pH 7.0. The heterogeneous electron transfer rate constant (k(s)) increases from 3.7 in the scan rate range from 0.2 to 3.0 V s(-1) and level off at 63.7 s(-1). Furthermore, the peroxide-dependent hydroxylation of aromatic compounds was applied to develop a sensor for naphthalene and nitrophenol. The amperometric measurements of naphthalene are based on the indication of H(2)O(2) consumption. For the chitosan-embedded gold nanoparticle system, the linear range extends from 4 to 40 μM naphthalene with a detection limit of 4.0 μM (S/N=3) and repeatability of 5.7% for 40 μM naphthalene., (Copyright © 2010 Elsevier B.V. All rights reserved.)

Novel molecularly imprinted polymers (MIPs) for the recognition of nitrofurantoin (NFT) were prepared by photoinitiated polymerisation in polar solvent using 2,6-bis(methacrylamido) pyridine (BMP) as the functional monomer and carboxyphenyl aminohydantoin (CPAH) as the analogue of the template. The binding constants of the complex between BMP and nitrofurantoin or CPAH in DMSO were determined with 1H NMR titration to be 630+/-104 and 830+/-146 M(-1), respectively. To study the influence of the functional monomer, two polymer compositions were prepared containing the template, the functional monomer and the crosslinker in the molar ratio 1:1:12 for MIP1 and 1:4:20 for MIP2, respectively. The imprinting factor at saturation concentration of nitrofurantoin, which is the ratio of the amount bound to the MIP and the non-imprinted control polymer (NIP), was determined to be 2.47 for MIP1 and 2.49 for MIP2. The cross reactivity of the imprinted polymers seems to be determined by the ability to form hydrogen bonds to the functional monomer while the shape of the molecule has no real influence.

We developed a dual piezoelectric/amperometric sensor for the detection of two unrelated analytes in one experiment that uses propidium to anchor acetylcholinesterases (AChE) at the surface. This mass-sensitive sensor does not only allow the examination of the interaction between AChE and the modified surface but also the detection of in situ inhibition of the surface-bound AChE. Here we describe the application of the propidium-based sensor in combination with a modified AChE. For this reason the cocaine derivative benzoylecgonine (BZE) was coupled via a 10A long hydrophilic linker - 1,8-diamino-3,4-dioxaoctane - to carboxylic groups of the AChE after EDC/NHS activation. Thus the modified AChE (BZE-AChE) possesses an additional recognition element besides the inhibitor binding site. After the deposition of BZE-AChE on the sensor surface the binding of an anti-BZE-antibody to the BZE-AChE can be monitored. This makes it possible to determine two analytes - cocaine and organophosphate - in one experiment by measuring antibody binding and decrease in enzymatic activity, respectively. Furthermore it was also shown that other cocaine-binding enzymes, e.g., butyrylcholinesterase, can bind to the modified BZE-AChE. The competitive immunoassay allowed the detection of cocaine with a dynamic range from 10(-9) to 10(-7)M. The organophosphate chlorpyrifos-oxon could be detected in concentrations from 10(-6) down to 10(-8)M after 20 min of injection time (equals to 500 microL sample volume.

Interactions of molecularly imprinted polymers containing phenyl boronic acid residues with fructosyl valine, fructose and pinacol, respectively are analysed in aqueous solution (pH 11.4) by using a flow calorimeter. The reversible formation of (two) cyclic boronic acid diesters per fructosyl molecule generates a 40-fold higher exothermic signal as compared to the control polymer. Whereas binding of pinacol to either the MIP or the control polymer generates a very small endothermic signal reflecting a negligible contribution of the esterification to the overall process. An "apparent imprinting factor" of 41 is found which exceeds the respective value of batch binding procedures by a factor of 30. Furthermore, the MIP sensor was used to characterise the crossreactivity. The influence of shape selective molecular recognition is discussed.

Molecularly imprinted polymers (MIPs) against fructosyl valine (Fru-Val), the N-terminal constituent of hemoglobin A1c beta-chains, were prepared by cross-linking of beta-D-Fru-Val-O-bis(4-vinylphenylboronate) with an excess of ethylene glycol dimethacrylate (EDMA) or trimethylolpropane trimethacrylate (TRIM). Control MIPs were prepared in analogy by cross-linking the corresponding vinylphenylboronate esters of fructose and pinacol. After template extraction batch rebinding studies were performed using different pH values and buffer compositions. The Fru-Val imprinted TRIM cross-linked polymer binds about 1.4 times more Fru-Val than the fructose imprinted polymer and 2.7 times more Fru-Val than pinacol imprinted polymer. The highest imprinting effect was obtained in 100 mM sodium carbonate/10% methanol (pH 11.4). The TRIM cross-linked Fru-Val imprinted polymer showed a better specificity than the EDMA cross-linked polymer. The binding of valine was very low. Thermo gravimetric analysis indicated that the generated Fru-Val imprinted polymer has high thermo stability. No change in binding was observed after incubation of the polymers in buffer at 80 degrees C for 36 h. Since the functional group of the polymers (phenyl boronic acid) targets the sugar part of Fru-Val the imprint technique used should also be applicable for the development of MIPs against other glycated amino acids and peptides.

A sensor for cholinesterases (ChEs) has been developed by binding carnitine via 1,6-diaminohexane to a mixed monolayer of 11-mercaptoundecanoic acid/11-mercapto-1-undecanol on the surface of a gold-coated quartz crystal. Catalytically active and organophosphate-inhibited acetyl- and butyryl-cholinesterases of different origins were tested for their binding ability to D- and L-carnitine, respectively. The binding constants were calculated by using a one-to-one binding model. Additionally, the activity of the immobilized ChE was monitored and the operational stability was investigated amperometrically.

Cytochrome P450 (CYP) is a large family of enzymes containing heme as the active site. Since their discovery and the elucidation of their structure, they have attracted the interest of scientist for many years, particularly due to their catalytic abilities. Since the late 1970s attempts have concentrated on the construction and development of electrochemical sensors. Although sensors based on mediated electron transfer have also been constructed, the direct electron transfer approach has attracted most of the interest. This has enabled the investigation of the electrochemical properties of the various isoforms of CYP. Furthermore, CYP utilized to construct biosensors for the determination of substrates important in environmental monitoring, pharmaceutical industry and clinical practice.

Cholinesterases can be used as sensitive biorecognition elements for widely used agricultural pesticides. This requires highly purified and inhibitor-free enzyme preparations. In the present work the cocaine derivative benzoylecgonine was for the first time used as the molecular recognition element for the purification of acetylcholinesterase from Electrophorus electricus by affinity chromatography. The preparation of enriched enzyme without the contamination by an inhibitor, which is traditionally used for eluting the "affinity" bound protein, was achieved. The specific activity was 2.2-fold increased to 3100 Umg(-1). The same cocaine derivative was immobilized on the surface of a piezoelectric crystal in order to analyze the binding of acetylcholinesterases from two different species, E. electricus and Drosophila melanogaster, to the immobilized inhibitor. Evaluation of the binding curves allowed the analysis of the binding kinetics. These experiments are fundamental for the development of a (competitive) biosensor for inhibitors of cholinesterase.

This paper describes a new method for the sensitive detection of cholinesterase inhibitors based on real-time monitoring using a piezoelectric biosensor. The cholinesterase inhibitor paraoxon was immobilized on the sensing surface via a chelate complex as the recognition element. At first, the conjugate of N-mercaptoundecanoic acid (MUA) with Nalpha,Nalpha-bis (carboxymethyl)-L-lysine (NTA-Lys) was chemisorbed to form a self-assembled monolayer on the surface of the gold electrode of the piezosensor. In the next step, paraoxon-spacer-hexahistidine conjugate was linked to the MUA-Lys-NTA layer via the chelate complex with Ni2+. The paraoxon-modified surface thus obtained was applied for the binding of human butyrylcholinesterase (BChE). Regeneration of the sensing surface was achieved by splitting the chelate complex with EDTA and depositing a fresh layer of Ni2+ followed by addition of the paraoxon-spacer-hexahistidine. In the presence of free inhibitors like diisopropylfluorophosphate (DFP), binding of BChE to the surface-bound paraoxon was decreased. In this way, a competitive affinity assay for organophosphorus compounds was developed. The limit of detection for DFP as a model compound was 10 nmol/l (ca. 2 microg/l). This new concept seems suitable for constructing biosensors for the group-specific detection of cholinesterase-inhibiting substances like insecticides in the field.

A biosensor for detection of formate at submicromolar concentrations has been developed by co-immobilizing formate dehydrogenase (FDH, E.C. 1.2.1.2), salicylate hydroxylase (SHL, E.C. 1.14.13.1) and NAD(+) linked to polyethylene glycol (PEG-NAD(+)) in a poly(vinyl alcohol) (PVA) matrix in front of a Clark-electrode. The principle of the bi-enzyme scheme is as follows: formate dehydrogenase converts formate into carbon dioxide using PEG-NAD(+). Corresponding PEG-NADH produced is then oxidized to PEG-NAD(+) by salicylate hydroxylase using sodium salicylate and oxygen. The oxygen consumption is monitored with the Clark-electrode. The advantages of this biosensor approach are the effective re-oxidation of PEG-NADH, and the entrapment of PEG-NAD(+) resulting in avoiding the addition of expensive cofactor to the working medium for each measurement. This bi-enzyme sensor has achieved a linear range of 1-300 microM and a detection limit of 1.98 x 10(-7) M for formate (S/N=3), with the response time of 4 min. The working stability is limited to 7 days due to the inactivation of the enzymes. Only sodium salicylate was needed in milli-molar amounts.

The progesterone concentration in blood samples can be utilised as a marker for the diagnosis of early pregnancy, endocrinopathy and virilism. Here, we describe a method for progesterone detection and measurement in whole blood samples by a surface sensitive biosensor used in conjunction with an integrated optical grating coupler. This device determines refractive index changes near the biosensor's surface. Hence, biological species bound to a surface layer can be measured in real-time without any label. For the measurements, we have modified the indirect competitive immunoassay principle. The concentration of the progesterone antibody was kept at 1 microg/ml. Progesterone concentration was determined in buffer solution and whole blood in a range between 0.005 and 10 ng/ml. The detection limit was determined to be 3 pM. The relative standard deviation was calculated to be 3.5%., (Copyright 2002 Elsevier Science B.V.)

This paper describes the development of a highly sensitive competitive immunoassay with the piezoelectric sensor. The immobilized derivative of cocaine was benzoylecgonine-1,8-diamino-3,4-dioxaoctane (BZE-DADOO). For the immobilization of BZE-DADOO, the conjugate BZE-DADOO with 11-mercaptomonoundecanoic acid (MUA) was synthesized via 2-(5-norbornen-2,3-dicarboximide)-1,1,3,3-tetramethyluronium-tetrafluoroborate (TNTU), followed by the creation of the conjugate monolayer on the piezosensor electrodes. For the optimization of the competitive assay we used electrodes with rough or smooth gold areas and for the interaction with immobilized antigen different anti-cocaine sheep polyclonal (pAb, either whole IgG or Fab fragment) and mouse monoclonal (mAb, whole IgG) antibodies. The assay of cocaine developed achieved a detection limit (LOD) of 100 pmol/l (34 ng/l) using the sheep antibody (IgG) and piezoelectric sensors with a smooth gold surface. The total time of one analysis was 15 min and the measuring area of the sensor could be used more than 40 times without losing its sensitivity.