Search

This research investigated the influence of the layered structure of paper on its selected strength properties. Two types of cellulose pulp were used: unbleached kraft pine pulp (UBSK) and unrefined bleached birch kraft pulp (BHK). Multi-ply papers were obtained from layers of appropriate grammage formed separately and bonded in a wet state. Paper layers were formed from primary pulps (UBSK and BHK) or their mixtures (three-ply UBSK-BHK paper and three-ply UBSK-BHK-UBSK paper), from which various variants of laboratory paper samples were made. This work focused on three-layer papers. The obtained laboratory sheets were analysed for changes in tear resistance, tensile strength, bursting strength, short span compression strength (SCT), and corrugating medium test (CMT). In most cases, three-layer structures were characterised by higher strength parameters than single-layer papers. The tear strength and SCT of papers consisting of three layers formed from both mixed pulps were slightly lower than those of solid papers. The results demonstrate the feasibility of producing three-ply paper with significantly reduced variability in parameters such as elongation and bursting strength, which are inherently subject to high variability.

The potential of paper and paperboard as fiber-based materials capable of replacing conventional polymer-based materials has been widely investigated and evaluated. Due to paper’s limited extensibility and inherent heterogeneity, local structural variations lead to unpredictable local mechanical behavior and instability during processing, such as mechanical forming. To gain a deeper understanding of the impact of mechanical behavior and heterogeneity on the paper forming process, the Finite Element Method (FEM) coupled with continuum modeling is being explored as a potential approach to enhance comprehension. To achieve this goal, utilizing experimentally derived material parameters alongside stochastic finite element methods allows for more precise modeling of material behavior, considering the local material properties. This work first introduces the approach of modeling heterogeneity or local material structure within continuum models, such as the Stochastic Finite Element Method (SFEM). A fundamental challenge lies in accurately measuring these local material properties. Experimental investigations are being conducted to numerically simulate mechanical behavior. An overview is provided of experimental methods for material characterization, as found in literature, with a specific focus on measuring local mechanical material structure. By doing so, it enables the characterization of the global material structure and mechanical behavior of paper and paperboard.

The potential of paper and paperboard as fiber-based materials capable of replacing conventional polymer-based materials has been widely investigated and evaluated. Due to paper's limited extensibility and inherent heterogeneity, local structural variations lead to unpredictable local mechanical behavior and instability during processing, such as mechanical forming. To gain a deeper understanding of the impact of mechanical behavior and heterogeneity on the paper forming process, the Finite Element Method (FEM) coupled with continuum modeling is being explored as a potential approach to enhance comprehension. To achieve this goal, utilizing experimentally derived material parameters alongside stochastic finite element methods allows for more precise modeling of material behavior, considering the local material properties. This work first introduces the approach of modeling heterogeneity or local material structure within continuum models, such as the Stochastic Finite Element Method (SFEM). A fundamental challenge lies in accurately measuring these local material properties. Experimental investigations are being conducted to numerically simulate mechanical behavior. An overview is provided of experimental methods for material characterization, as found in literature, with a specific focus on measuring local mechanical material structure. By doing so, it enables the characterization of the global material structure and mechanical behavior of paper and paperboard. [ABSTRACT FROM AUTHOR]

This research investigated the influence of the layered structure of paper on its selected strength properties. Two types of cellulose pulp were used: unbleached kraft pine pulp (UBSK) and unrefined bleached birch kraft pulp (BHK). Multi-ply papers were obtained from layers of appropriate grammage formed separately and bonded in a wet state. Paper layers were formed from primary pulps (UBSK and BHK) or their mixtures (threeply UBSK-BHK paper and three-ply UBSK-BHK-UBSK paper), from which various variants of laboratory paper samples were made. This work focused on three-layer papers. The obtained laboratory sheets were analysed for changes in tear resistance, tensile strength, bursting strength, short span compression strength (SCT), and corrugating medium test (CMT). In most cases, three-layer structures were characterised by higher strength parameters than single-layer papers. The tear strength and SCT of papers consisting of three layers formed from both mixed pulps were slightly lower than those of solid papers. The results demonstrate the feasibility of producing three-ply paper with significantly reduced variability in parameters such as elongation and bursting strength, which are inherently subject to high variability. [ABSTRACT FROM AUTHOR]

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage. [ABSTRACT FROM AUTHOR]

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage.

Hemp hurd fiber, a low-value waste stream from the hemp industry, has potential downstream applications as an alternative to non-renewable plastics for single-use food service ware and packaging applications. Packaging paper substrates made from chemically pulped hemp hurd, mixed in varying ratios with bleached thermomechanical radiata pine pulp were developed and tested. Handsheets were characterized using several mechanical property tests including tensile strength, tearing resistance, burst strength, short-span compression, ring crush, together with Gurley air resistance, contact angle, and Cobb60 tests. Generally, addition of hemp hurd fibers significantly improved handsheet mechanical properties. Hot-pressing of the handsheets so as to approximate molded fiber thermoforming further enhanced their performance, with pure hemp hurd handsheets having the highest mechanical properties and barrier performance. A prototype was successfully thermoformed from hemp fiber, demonstrating overall feasibility of this fibre source for molded fibre objects.

Flow and spontaneous imbibition phenomena in porous media are important for various industrial applications, including printing and medical lateral flow assays. Their quantitative characterization is important to better understand and select the appropriate raw materials. However, standard methods often require time-consuming tests, and/or expensive equipment. Different time scales must be considered, limiting the range of possible characterization tools. A novel experimental approach based on image analysis for characterizing spontaneous imbibition processes is presented. Hence, ultra-fast diffusion may be quantitatively characterized. Models are issued from the literature to consider physical phenomena at small (milliseconds) and medium range (seconds) of time scales. The obtained experimental data fit with theoretical results, providing valuable insights into the understanding of fluid flow behavior at different time scales. Furthermore, the identification of some physical properties for either the fluid, or the substrate, based on the theoretical models are possible, as the contact angle, which remains to be otherwise challenging. This study contributes to bridging the gap between spontaneous imbibition and capillary phenomena at different time scales, their modeling, and a characterization of material and/or fluid properties paving the way for enhanced understanding and control of fluid behavior in porous media. Different papers are considered to illustrate the method. [ABSTRACT FROM AUTHOR]

Flow and spontaneous imbibition phenomena in porous media are important for various industrial applications, including printing and medical lateral flow assays. Their quantitative characterization is important to better understand and select the appropriate raw materials. However, standard methods often require time-consuming tests, and/or expensive equipment. Different time scales must be considered, limiting the range of possible characterization tools. A novel experimental approach based on image analysis for characterizing spontaneous imbibition processes is presented. Hence, ultra-fast diffusion may be quantitatively characterized. Models are issued from the literature to consider physical phenomena at small (milliseconds) and medium range (seconds) of time scales. The obtained experimental data fit with theoretical results, providing valuable insights into the understanding of fluid flow behavior at different time scales. Furthermore, the identification of some physical properties for either the fluid, or the substrate, based on the theoretical models are possible, as the contact angle, which remains to be otherwise challenging. This study contributes to bridging the gap between spontaneous imbibition and capillary phenomena at different time scales, their modeling, and a characterization of material and/or fluid properties paving the way for enhanced understanding and control of fluid behavior in porous media. Different papers are considered to illustrate the method.

Wood-based paper fibers are inherently biodegradable. In contact with moist soil and in compost, papermaking fibers are readily broken down by soil microbes. Resistance to biodegradation is needed, as paper is used for special applications such as mulching in agriculture and forestry, the coating of construction materials, and for packing and wrapping under conditions where packaging materials may be exposed to contact with moist soil or other type microbial active contamination. A preceding study showed that paper chemical crosslinking with glyoxal, citric acid (CA), or methylated 1,3-dimethylol-4,5-dihydroxyethylene urea (mDMDHEU) results in substantially improved paper wet strength and lower paper water absorbency. The present study examined the efficiency of chemical crosslinking treatments with CA and with mDMDHEU to decrease the biodegradation rate of laboratory paper sheets and a sack paper, both made of kraft fibers. The biodegradation was examined using a 48-h enzymatic degradation test and a 2-month soil burial test. The results indicate that chemical crosslinking is an effective non-biocidal method for making sulphate kraft paper more resistant to biodegradation. In some end-uses, improved resistance to biodegradation, along with improved paper wet performance, can enhance paper performance comparable to plastic films.

Paper, which is in fact a very complex cellulose-based product derived from different lignocellulosic resources, is usually regarded as a simple omnipresent commodity in our lives. Wood fibers derived from trees are the most employed sources for papermaking purposes. From an environmental protection perspective, and for their essential role in our life (they give us the life itself through their foliar system supporting the photosynthesis process), trees should not be extensively cut down and they should be used less and less for papermaking. Thus, employment of non-woody alternative sources for papermaking could be exploited more as an attractive and feasible option.

Wood-based paper fibers are inherently biodegradable. In contact with moist soil and in compost, papermaking fibers are readily broken down by soil microbes. Resistance to biodegradation is needed, as paper is used for special applications such as mulching in agriculture and forestry, the coating of construction materials, and for packing and wrapping under conditions where packaging materials may be exposed to contact with moist soil or other type microbial active contamination. A preceding study showed that paper chemical crosslinking with glyoxal, citric acid (CA), or methylated 1,3-dimethylol-4,5-dihydroxyethylene urea (mDMDHEU) results in substantially improved paper wet strength and lower paper water absorbency. The present study examined the efficiency of chemical crosslinking treatments with CA and with mDMDHEU to decrease the biodegradation rate of laboratory paper sheets and a sack paper, both made of kraft fibers. The biodegradation was examined using a 48-h enzymatic degradation test and a 2-month soil burial test. The results indicate that chemical crosslinking is an effective non-biocidal method for making sulphate kraft paper more resistant to biodegradation. In some end-uses, improved resistance to biodegradation, along with improved paper wet performance, can enhance paper performance comparable to plastic films. [ABSTRACT FROM AUTHOR]

Paper, which is in fact a very complex cellulose-based product derived from different lignocellulosic resources, is usually regarded as a simple omnipresent commodity in our lives. Wood fibers derived from trees are the most employed sources for papermaking purposes. From an environmental protection perspective, and for their essential role in our life (they give us the life itself through their foliar system supporting the photosynthesis process), trees should not be extensively cut down and they should be used less and less for papermaking. Thus, employment of non-woody alternative sources for papermaking could be exploited more as an attractive and feasible option. [ABSTRACT FROM AUTHOR]

The production of release coatings has been increasing in recent years because of their use in various fields. However, commercially available release coatings are regarded as non-recyclable. As a consequence, the repulping of these residues is difficult, and their presence in the recycling stream represents an important source of contamination. One solution to this problem is to use new coating materials that can replace the siliconized backing, provided that these new materials are recyclable. As a solution to this problem, the authors propose the use of alkylated phosphorylated fibers to produce an environmentally friendly and inexpensive release paper. The results show that a surface application of hydrophobic phosphorylated fibers reduces the surface free energy of the paper support, as well as the peel strength, which facilitates the separation of the adhesive tape.

An awareness of the problems associated with the use of plastics can provide new opportunities for the paper industry. We have to try to enhance the public awareness of the environmental value of papers by using diverse advertising approaches. We have to collaborate to make paper more viable to replace plastics in many uses. The collaboration not only between industry and academia but also between countries and associations is essential to advance the age of paper. [ABSTRACT FROM AUTHOR]

The production of release coatings has been increasing in recent years because of their use in various fields. However, commercially available release coatings are regarded as non-recyclable. As a consequence, the repulping of these residues is difficult, and their presence in the recycling stream represents an important source of contamination. One solution to this problem is to use new coating materials that can replace the siliconized backing, provided that these new materials are recyclable. As a solution to this problem, the authors propose the use of alkylated phosphorylated fibers to produce an environmentally friendly and inexpensive release paper. The results show that a surface application of hydrophobic phosphorylated fibers reduces the surface free energy of the paper support, as well as the peel strength, which facilitates the separation of the adhesive tape. [ABSTRACT FROM AUTHOR]

Chemical crosslinking is an established method for improving the wet performance of paper. In the chemical crosslinking process, covalent bonds are formed between cellulosic surfaces. The formed intra- and interfiber bonds increase the paper's wet strength and reduce its water absorptivity. The majority of published studies concern crosslinking treatments with glyoxal, citric acid (CA), or with 1,2,3,4-butanetetracarboxylic acid (BTCA). The most severe disadvantage of the crosslinking treatments with glyoxal, CA, and BTCA is that the formed crosslinks make the fibers and the paper more brittle. This downside effect has largely impeded the utilization of crosslinking in paper and paperboard making. In the present study, handsheets made from Nordic bleached softwood kraft pulp (NBSK) were crosslinked with methylated 1,3-dimethylol-4,5-dihydroxyethylene urea (mDMDHEU), which is commonly used in cotton fabric finishing. Similar to using glyoxal and citric acid, crosslinking with mDMDHEU notably increased the handsheet wet strength and decreased the water absorption. Compared to the use of glyoxal or CA, the crosslinking with mDMDHEU did not make the handsheets that brittle. These results suggest that mDMDHEU could be a more viable crosslinking agent for improving the wet performance of paper products. [ABSTRACT FROM AUTHOR]

Paper, nanocellulose, and other polysaccharide-based materials can be excellent candidates for food packaging barrier layers, except that they tend to be vulnerable to moisture. This article reviews published research describing various chemical treatments having the potential to render hydrophobic character to such layers. Emphasis is placed on systems in which hydrophobic monomers are used to treat either particles or sheets comprised largely of polysaccharides. A goal of this review is to identify combinations of materials and procedures having promise for scale-up to industrial production, while providing effective resistance to moisture. The idea is to protect the underlying polysaccharide-based barrier layers such that they can continue to impede the transfer of such permeants as oxygen, greases, flavor compounds, and water vapor. A further goal is to minimize any adverse environmental impacts associated with the treatments. Based on the research articles considered in this review, promising hydrophobic treatments can be achieved involving silanes, ester formation, other covalent interactions, plasma treatments, and to some extent by various treatments that do not require formation of covalent bonds. The article is designed such that readers can skip ahead to items of particular interest to them.

Paper, nanocellulose, and other polysaccharide-based materials can be excellent candidates for food packaging barrier layers, except that they tend to be vulnerable to moisture. This article reviews published research describing various chemical treatments having the potential to render hydrophobic character to such layers. Emphasis is placed on systems in which hydrophobic monomers are used to treat either particles or sheets comprised largely of polysaccharides. A goal of this review is to identify combinations of materials and procedures having promise for scale-up to industrial production, while providing effective resistance to moisture. The idea is to protect the underlying polysaccharide-based barrier layers such that they can continue to impede the transfer of such permeants as oxygen, greases, flavor compounds, and water vapor. A further goal is to minimize any adverse environmental impacts associated with the treatments. Based on the research articles considered in this review, promising hydrophobic treatments can be achieved involving silanes, ester formation, other covalent interactions, plasma treatments, and to some extent by various treatments that do not require formation of covalent bonds. The article is designed such that readers can skip ahead to items of particular interest to them. [ABSTRACT FROM AUTHOR]

An eco-friendly time indicator (TI) was developed using cellulose-based materials. The TI comprises a dye, copy paper, nanofibrillated cellulose (NFC) film, and filter papers coated with NFC slurry and/or paraffin-free biowax. A suitable dye and its conditions were determined by observing the dye solutions and the migration pattern at the different concentrations. Commercial filter papers were prepared, and the dye migration rate, depending on physical properties, was evaluated. NFC was coated to control the dye migration rate of filter paper. In addition, biowax was used to impart hydrophobicity to filter papers used for supporting NFC films, storing the dye, and allowing the migration of dye. Finally, a TI was fabricated using those components. Methylene blue was selected as a dye for the TI due to its deep color and high solubility. The results showed that the key property of filter paper affecting the dye migration rate was the pore size. The migration rate could be reduced when NFC was coated on both sides of the filter paper. Since biowax modified the hydrophobicity of filter paper surface, it was used to make the NFC film-supporting paper, location for dye storage, and bottom-layer. In conclusion, a multilayered TI could be assembled using cellulose-based materials. [ABSTRACT FROM AUTHOR]

Smart, environmentally friendly alternatives, i.e., frankincense and rice starch, are recommended for usage in modern paper conservation processes during the re-sizing process treatments. Different concentrations of frankincense and rice starch were applied to paper samples before and after ageing. Multiple analysis methods were performed to ensure the effectiveness of these materials. Promising results were found, but at varying degrees according to the type and concentration of the materials. Scanning electron microscopy illustrated that the frankincense particles were completely absorbed into the cell walls after ageing. Results indicated that there was no considerable change in pH before and after treatment or ageing; the best results for decreasing the acidity utilized a treatment with a mixture of frankincense and rice starch in a 2 to 1 ratio (F2S1). Fourier transform infrared spectroscopy illustrated an increased CH2 region and decreased OH stretching as a result of the bonds formed from the starch and crystals formed by frankincense, which agreed with the increased coating and strength of the paper fibers. The total color change values of all the treated samples after ageing were less than 4.5. Frankincense was found to provide strength in supporting wood fibers. [ABSTRACT FROM AUTHOR]

The overall usefulness of the bursting energy absorption (BEA) was studied for a better analysis of paper strength properties. Additionally, the changes of the BEA during more complex deformations of paper products, e.g., preliminary or simultaneous tensile and burst, were determined. For the purpose of the research, an experimental setup was designed. The results showed that the correlation between BEA and bursting strength was linear, but the proportionality strongly depended on paper grade. Thus, a more accurate method to characterize the bursting resistance (BR) of paper was proposed. The BR parameter is described by the three following parameters: average bursting strength, average bursting energy absorption, and the slope of the fitted linear regression curve (relationship between the bursting energy absorption and the bursting strength). This method revealed new mechanical behaviors of papers related to their preloading. [ABSTRACT FROM AUTHOR]

People often think of paper as an environmentally harmful product because trees are cut down to make it. A new generation that has grown up in today’s digital society may think that the use of digital devices is a waste-free way to protect our environment. Although the pulp and paper industry is making various efforts to preserve the environment, it has not been properly recognized. Developing new technologies to produce better products at lower cost while protecting our environment is important. But it is also important to enhance the image of the pulp and paper industry in the eyes of the public. The pulp and paper industry’s efforts to reforestation for raw materials and to expand the recycling of waste paper should be more widely introduced.

Three natural extracted oils from Citrus reticulata peels, C. aurantifolia leaves, and Linum usitatissimum (linseeds) were used as antifungal agents against the growth of Aspergillus flavus and Penicillium chrysogenum. The following main compounds (determined via gas chromatography--mass spectrometry) were found. The essential oil (EO) from C. aurantiifolia leaves contained limonene (22.96%), geranyl acetal (13.53%), and geraniol acetate (13.33%); the n-hexane oil from C. reticulata peels contained methyl-13-cyclopentyltridecanoate (16.74%), and D-limonene (16.06%); and linseed oil contained linoleic acid (27.36%), and oleic acid (19.01%). The inhibition of fungal growth significantly was reached 100% against A. flavus at all tested C. aurantifolia leaf EO concentrations and at a concentration of 2000 µL/mL for linseeds oil. The growth inhibition reached 100% against P. chrysogenum with C. aurantifolia leaf EO concentrations of 125-2000 µL/mL. Citrus reticulata peel EO had 100% growth inhibition of P. chrysogenum at concentrations of 2000 µL/mL and 1000 µL/mL, while linseeds oil had 100% growth inhibition at 2000 µL/mL. Thermogravimetric analysis showed that C. aurantifolia EO yielded the greatest thermal stability and color change protection to cotton pulp, while linseed oil was found to protect wood pulpbased and historical papers. [ABSTRACT FROM AUTHOR]

During the embossing process, a fiber sandwich is compressed between embossing tools. The use of ultrasound causes a short-term increase in the material temperature in addition to causing plastic deformation. The combination of the material compression and an increase in material temperature leads to structural changes, which can be observed by the change in mechanical properties of the cardboard. This work investigated the influence of an ultrasonically induced temperature increase on the structural changes of cardboard. Using three-parameter combinations, different temperature levels were achieved with a material densification of less than 5%. Subsequently, the samples were subjected to selected physical and visual analyses to characterize the change in the fiber structure. With the increase of 124 °C material temperature there was a decrease of about 15% in the splitting resistance and 10% in the bending stiffness. [ABSTRACT FROM AUTHOR]

The Chinese national standard for paper ash measurement cannot meet the requirements for accurate and rapid ash measurement in actual production and scientific research because of the long measuring time, tedious procedures, and large human error. This paper reviews some worldwide devices and methods for rapid measurement of paper ash, including ceramic fiber muffle furnace, microwave muffle furnace, the addition of ash adjuvant, dry samples method, direct combustion of paper samples, oxygen-enriched combustion method, chemical analysis method, and ray method, etc. The differences and relationships are identified among these devices and methods. By comparing the different ash measurement methods, the rapid ash analyzer based on X-ray technology has the obvious advantages of short measuring time and small error. Lastly, the present situation and the development potential of these devices and methods are discussed in this review. [ABSTRACT FROM AUTHOR]

This paper reviews key advances in understanding the hydrodynamics of the forming section of papermaking during the years 1950 to 2000. Over this period papermaking advanced from rather slow-speed Fourdrinier machines to modern high-speed twin-wire formers. The advances are described in the context of technical problems faced at the time to increase machine speeds and improve paper properties. The scientific work and advances in machine design contributed greatly to the marvel of modern papermaking, which now includes machines 10 m wide operating at speeds over 100 km/h.

The Siamese people utilized the bark of the Coi tree (Streblus asper Lour.) to manufacture paper approximately 330 years ago. However, there are no studies yet related to the chemical properties of Coi bark as well as the morphological properties of Coi bark fiber and Coi pulp fiber. This research paper discussed such properties of Coi bark. The results indicated that Coi bark possessed a chemical composition that could potentially be used for pulp production, although it contained a high value of ash content, due to many calcium particles in the bark. Even though Coi pulp fibers were very long and stiff, with small lumens and thick cell walls, they could be felted naturally on a washing screen to make a strong wet sheet. This was due to a high felting power of fibers derived from a high value of fiber length and slenderness ratio. Therefore, the handsheets produced from Coi pulp fiber were obtained without chemical and beating treatments. These observations mean that both the archaeological and industrial applications of Coi bark, i.e., an ancient Samud Coi preservation and a new potential source of pulp fiber, are possible. [ABSTRACT FROM AUTHOR]

Functionalized layered double hydroxides (LDHs) based on a multimodifier system composed of itaconic acid (ITA) and titanate coupling agent (NDZ-201) were designed and fabricated in this paper with the aim to develop high-performance fire retardant paper. The structure of LDHs were characterized using Fourier transform infrared spectroscopic analysis, X-ray diffraction analysis, thermogravimetric analysis (TGA), scanning electron microscopic analysis, cone calorimetry, and laser particle size analysis. The results showed that carbonate anions were partially replaced by ITA, whereas the titanate coupling agent was attached to the surfaces of the hydrotalcites. The limiting oxygen index (LOI), TGA curves, total heat release rate (THR), and heat release rate (HRR) indicated that as the addition of hydrotalcites increased, the modified LDHs' LOI value and thermal stability noticeably increased compared to the unmodified hydrotalcites, and the HRR and THR of the material decreased. When the addition amount was 25%, the LOI of ITALDHs was 26.9%. However, the Mg-Al hydrotalcites adversely affected the strength index of flame-retardant paper; the modified hydrotalcites clearly reduced this effect, and the whiteness of paper increased and reached 83%. [ABSTRACT FROM AUTHOR]

Multilayer panels that have paper cores with hexagonal cells continue to have a limited application in furniture production. In contrast, there are no sandwich honeycomb panels with cores containing rectangular cells employed in this industry. Such cores should distinguish themselves by strong orthotropic advantages, in particular, for designing shelves and partitions of cabinet furniture. Hence, the objective of this study was to determine the effect of core rectangular paper cells on the mechanical properties of three-layer furniture panels. The authors decided to ascertain relative density and elasticity constants of the designed cells. The results of empirical experiments of cell elasticity moduli were compared with the results of the analytical calculations. The impact of sample width on their mechanical properties was determined. It was demonstrated that cores with hexagonal cells in furniture panels could be replaced by cores with rectangular cells. [ABSTRACT FROM AUTHOR]

Trametes versicolor and Pleurotus ostreatus were used for the biopulping from pineapple leaf fiber (PALF). PALF substrate was subjected to T. versicolor for 2 to 6 weeks and to P. ostreatus for 4 to 8 weeks. The yields, holocellulose and lignin contents, and extractives in ethanol-toluene mixture and in sodium hydroxide (NaOH) solution were evaluated. Fourier transform infrared spectroscopy (FTIR) spectra, thermogravimetric analysis (TGA), and color studies by L*a*b* systems were used for sample analysis. The results showed that the pulp yield was 55% to 70% with P. ostreatus and 35% to 50% with T. versicolor. Longer colonization periods increased the amount of holocellulose and decreased the amount of lignin and extractives in ethanol-toluene and NaOH solution. TGA showed an increase in intensity associated with cellulose, and the observed inflexion was attributed to lignin, which showed a tendency to fade. The FTIR spectrum showed high intensity between 3100 cm-1 and 3600 cm-1 (cellulose) and decreased intensity at 1730 cm-1 (lignin). For both fungi, the pulp color produced an increase in L* color parameter and decreased in yellowness, while little variation was observed in redness. The most appropriate colonization period was 5 weeks for P. ostreatus and 4 weeks for T. versicolor.

Biomaterials and new processes (3D printing and flexible hybrid electronics) offer opportunities to break free from a 2D paper world by allowing for the development of smart multi-dimensional structures. While there has been recent progress reported in each of these areas of technology, to date, the merger of these technologies has been very limited. We believe that their merger offers boundless opportunities and an opportunity for the paper industry to innovate a low cost, sustainable housing solution capable of promoting the well-being of its occupants while minimizing the environmental impact of its daily use.

The objective of this study was to characterize the properties of pulp and paper produced from tea (Camellia sinensis) wastes, an agricultural residue widely available in Turkey, using the kraft-anthraquinone (AQ) cooking method. The chemical components and fiber morphology of tea wastes were investigated. The results indicated that tea wastes had low holocellulose, cellulose, and α-cellulose contents and high lignin content. Also, the suitability of the fiber for pulp and paper production was examined, and the fiber length, fiber width, lumen diameter, and cell wall thickness were measured. According to these values, it was found that the strength properties of papers obtained from tea wastes were insufficient. Therefore, tea waste pulps were mixed with Turkish pine pulps at various ratios. Twelve different cooking experiments were performed on the tea wastes, and the cooking with the best pulp yield was used for mixing. The second cooking, with 0.1% AQ, gave the best yield (33.26%), an increase of about 3.51% compared to the first cooking with no AQ. The physical and optical properties of the papers were also examined. Results showed that paper properties were improved by increasing the Turkish pine pulp rate. Consequently, tea wastes can be used in pulp and paper production when combined with softwood pulps.

The aim of this study was to improve the electrical resistivity, mechanical properties, and interfacial properties between the carbon fiber (CF) and cellulose of conductive paper containing 10% CF so as to better meet the demands for electric heating wood floors. With waterborne polyurethane (WPU) treatment and nitrogen plasma modification methods, the interfacial properties between CF and cellulose were improved dramatically. Fourier transform infrared spectrometry (FTIR) revealed that the plasma modification method reduced the C-H contents and introduced numerous polar groups onto the CF surface. Scanning electron microscopy (SEM) showed that the CF modified by WPU and plasma had good adhesion with cellulose. The tensile index, tensile energy absorption index, and burst index of the paper were enhanced because of the plasma and WPU coating. The carbon fiber and WPU method presented good synergistic action with respect to mechanical properties and electrical resistivity, and the lowest electrical resistivity of conductive paper was reduced from 0.68 •cm2 to 0.44 •cm2.

Paper properties determine the product application potential and depend on the raw material, pulping conditions, and pulp refining. The aim of this study was to construct mathematical models that predict quantitative relations between the paper density and various mechanical and optical properties of the paper. A dataset of properties of paper handsheets produced with pulps of Acacia dealbata, Acacia melanoxylon, and Eucalyptus globulus beaten at 500, 2500, and 4500 revolutions was used. Unsupervised classification techniques were combined to assess the need to perform separated prediction models for each species, and multivariable regression techniques were used to establish such prediction models. It was possible to develop models with a high goodness of fit using paper density as the independent variable (or predictor) for all variables except tear index and zero-span tensile strength, both dry and wet.

Newly developed packaging paper made of biopulped pineapple leaf fiber (PALF) and poly(lactic acid)(PLA) was studied. PALF packaging sheets were solvent impregnated with PLA at different concentrations in order to improve their moisture barrier and mechanical performance. With the impregnation of PLA at a concentration of 4%, the packaging material exhibited a low moisture uptake and a high tear index. An electron micrograph of the sample at 4% impregnation revealed uniform and packed PLA reversed microsphere morphology. These results suggest that surface coating via biodegradable polymers, such as PLA, may be utilized for manufacturing packaging materials in industrial applications. This new packaging material could reduce the dependency on wood-based paper and plastic-based packaging.

The present study shows that barley straw (Hordeum vulgare) can be a supplementary raw material of softwoods and hardwoods such as Pinus sylvestris and Eucalyptus camaldulensis, respectively, for the production of cellulose and paper, reducing an agricultural residue that has no added value. Barley straw has a lower content of cellulose at 36.4% than P. sylvestris and E. camaldulensis, but it contains a lower quantity of lignin, 15.9%. After pulping with soda anthraquinone (AQ), high contents of cellulose (56.5 to 67.5%) and holocellulose (>80%) were attained. Paper sheet properties were able to reach, and even improve upon, those of wood species (Pinus and Eucalyptus) pulped with kraft. Better values of total yield (56.5%), Kappa number (8.9), and ISO brightness (36.4%), were attained for paper sheets from barley straw pulp versus E. camaldulensis and P. sylvestris, respectively, and comparable values for viscosity, tensile, and burst index were obtained.

This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or better than papers made from soda-AQ delignified pulps conducted in a single step. Also, a liquid fraction with a substantial content in hemicellulosic extracts was recovered in the simplified process. Autohydrolysis of the raw material facilitates carrying out soda-AQ pulping under milder conditions. In addition, autohydrolysis improves other properties relative to paper from raw cellulose pulp. Yield, kappa number, and brightness for pulp from solid residues of autohydrolysed eucalyptus wood were similar to those for pulp from untreated eucalyptus wood.

Short carbon fibers (SCF) were modified with oxidation and coupling treatment to improve their water-wettability and bonding properties. Four types of dispersants were studied and discussed. Short carbon fibers/plant fiber (PF) composite papers were prepared by papermaking techniques. Scanning electron microscopy (SEM) and tests to determine zeta potential, absorbance, tensile index, and conductivity were carried out to investigate the modified effect of SCF and the interfacial properties. Modification experimental results showed that the surface grooves were deepened and new superficial grooves were generated by the liquid acid oxidation. The reaction with the silane coupling agent provided higher density and more uniform distribution on the SCF surface than that of organic titanate, and it obviously increased the roughness and the absolute value of zeta potential. After modification, the hydrophilic properties and dispersion in aqueous solutions were improved, the SCFs could form a good mechanical grip with plant fibers, and the conductivity and physical strength of SCF/PF composite papers were enhanced. It was shown that there was obvious adhesive binding at the fiber overlap nodes by the SEM analysis. It was confirmed that the improvement of physical properties of composite paper can be ascribed to the interfacial enhancement.

Precipitated calcium carbonate (PCC) is a filler that is widely used for papermaking, and lime sludge is a special type of PCC recovered from the black liquor from kraft pulping. There has been some concern that lime sludge may interfere with the development of paper’s hydrophobicity in comparison with commercial PCC and ground calcium carbonate (GCC) due to the presence of impurities when alkyl ketene dimer (AKD) is used as the sizing additive. In this work, fillers with different particle size distributions were prepared, and the effects of particle composition on surface chemistry of fillers, adsorption for AKD, sizing degree of final paper sheets, and retention behavior of fillers were evaluated. The results showed that, through matching different particle size distributions for lime sludge fillers, the negative zeta potential decreased from -26.2 mV to -20.8 mV, the specific surface area decreased from 15.0 m2/g to 9.1 m2/g, and total pore volume decreased from 0.037 cm3/g to 0.026 cm3/g, which was favorable for the low adsorption for AKD. Consequently the sizing effect of filled paper was improved. Moreover, the retention rate also was increased by changing the particle size distribution of lime sludge.

The pulp and paper industry in Europe produces over 11 million tons of waste per year. Given high landfill operational costs, thermal coprocessing with biomass may be a viable management and valorisation option for such wastes. In this work, the analysis of biomass (wood sawdust), mixture of primary and secondary pulp mill sludge and their respective blends (50 wt.%, 60 wt.%, 70 wt.% of sludge) was assessed by thermogravimetric analysis. One of the possibilities to ensure valorisation of paper pulp mill sludge is its combustion in the form of pellets containing a different amount of sludge. Production of pellets samples was realised on laboratory experimental device. The measurements showed that increasing the content of paper sludge in the produced pellets reduced the calorific value and increased the ash content. This research deals also with the effect of paper sludge on the ash melting temperatures. The results indicated that a higher content of paper sludge in the pellets increased the ash melting temperatures. This advantage of paper sludge can be utilized in co-combustion of biomass with a low ash melting temperature. [ABSTRACT FROM AUTHOR]

Paper is widely used as a substrate for inkjet printing, where the paper feature heavily impacts the print quality, especially the color reproduction. The unprinted area on paper is visible and applied as a background reflectance for the toner layer. Hence, it is worthwhile to understand the effects of paper whiteness on print color reproduction. In this study, the tested papers were treated with different dyes, which resulted in the change of the paper's optical properties, but not surface roughness. The print density was impacted by the paper whiteness and ISO brightness. The effect of the paper whiteness on the print density is a stronger linear correlation compared to the ISO brightness. Paper whiteness has a positive correlation with the ISO brightness. The print colorimetric values (lightness and chroma values) increased with increasing paper whiteness up to a certain level, after which the paper whiteness did not have a noticeable impact on its print lightness and chroma values. The print color (a* and b* values) was affected by its corresponding paper color. [ABSTRACT FROM AUTHOR]

The microstructure and reactivity of a novel nonwoven cellulose fiber cellular biocomposite (microbial paper) was studied relative to long-term stabilization of potentially any microorganism. Cells were incorporated during the papermaking process as an integral component of a highly porous cellular biocomposite that can be dry stabilized. Hydrogen gas production from acetate via the activity of the nitrogenases in Rhodopseudomonas palustris CGA009, entrapped at a very high concentration, in hand-made microbial paper was sustained for > 1000 h at a rate of 4.0 ± 0.28 mmol H2/m2 h-1 following rehydration. This rate is 2x and 10x greater than previously reported H2 production rates by Rps. palustris latex coatings that were dried on polyester and non-dried formulations applied to the surface of paper, respectively. By vacuumdewatering and controlled drying steps to the microbial papermaking process and incorporating blends of microfibrillar (MFC), softwood (SW), and hardwood (HW) cellulose fibers, microbial paper films were fabricated that produced H2 gas at 3.94 ± 1.07 mmol H2/m2 h-1 and retain up to 60 mg/m-2 dry cell weight (DCW) of Rps. palustris. The MFC content appears to determine the final cell load and may affect gas/moisture mass transfer properties of the biocomposite. [ABSTRACT FROM AUTHOR]

This paper reviews key advances in understanding the hydrodynamics of the forming section of papermaking during the years 1950 to 2000. Over this period papermaking advanced from rather slow-speed Fourdrinier machines to modern high-speed twin-wire formers. The advances are described in the context of technical problems faced at the time to increase machine speeds and improve paper properties. The scientific work and advances in machine design contributed greatly to the marvel of modern papermaking, which now includes machines 10 m wide operating at speeds over 100 km/h. [ABSTRACT FROM AUTHOR]

Fibre-based packaging materials are widely utilized all over the world. They have several important advantages in comparison with fossil-based packaging: biodegradability, recyclability, and renewability. However, fibre-based packaging cannot fully compete with plastic in its barrier properties. Also there are limitations regarding its shapes due to poorer formability. The deep-drawing forming process can be used for the production of advanced three-dimensional shapes from paper-based materials. Formability and related characteristics are essential for deep-drawing of paper-based materials. This paper aims to give an overview of the deep-drawing of paper-based materials with the emphasis on the experienced deformations, on the role of mechanical properties of materials in deep-drawing, and on the typical defects found in the shapes after the forming. Additionally, strategies are proposed to help mitigate common problems in deep-drawing.

Biomaterials from olive tree pruning are an abundant agricultural residue in various Mediterranean regions. A suggested use of this residue is its separation in a main fraction (trunks and stems with diameter > 1 cm) and a residual fraction (leaves and stems with diameter 1 < cm), using biorefinery procedures. The main fraction is cooked with ethanol, giving rise to a pulp, which can be used either in paper or in bioethanol production if before pulping the main fraction is subjected to a hydrothermal treatment. Pulping with 70% ethanol concentration, 185 °C for 80 min resulted in a pulp with a yield of 46.30% and a content of holocellulose, α-cellulose, and lignin of 77.17%, 62.49%, and 21.73%, respectively. The paper sheets obtained had a breaking length of 1168 m, a burst index of 0.44 kN /g, a tear index of 2.25 mN.m2/g, and a brightness of 43.66%. The pulp converted into bioethanol (by simultaneous hydrolysis and fermentation) achieved a conversion of 70 g bioethanol/100 g potential bioethanol. The residual fraction of olive tree prunings was subjected to combustion to produce thermal energy. The heating value was 18700 kJ/kg, the flame temperature range was 1094 to 2013 ºC, and the dew point temperature range of the flue gases was 47 to 53 °C.

This review describes the state-of-the-art of material derived from the forest sector with respect to its potential for use in the packaging industry. Some innovative approaches are highlighted. The aim is to cover recent developments and key challenges for successful introduction of renewable materials in the packaging market. The covered subjects are renewable fibers and bio-based polymers for use in bioplastics or as coatings for paper-based packaging materials. Current market sizes and forecasts are also presented. Competitive mechanical, thermal, and barrier properties along with material availability and ease of processing are identified as fundamental issues for sustainable utilization of renewable materials.

Release paper is a special paper grade with one or both sides coated with non-sticking materials. Silicone is currently the only material used to produce release paper at the industrial level. Its remarkable properties and availability ensure product quality and sustainability of the industrial production. Meanwhile, the stability of silicone polymers raises serious environmental problems in terms of paper substrate recyclability. Studies are currently under way to evaluate the ability of phosphate esters as a new class of compounds capable of developing non-adhesive surface properties. This paper presents initial attempts to coat the paper with phosphate esters and to assess phosphate ester / fibrous substrate and phosphate ester / adhesive interactions. The results show that this class of compounds exhibits non-adhesive properties and, when coated on paper under certain conditions, can lead to a non-sticking surface. Despite the fact that there is a long way to achieve ester anchoring to surface fibers and to control the peeling force from an adhesive tape, preliminary results are encouraging.

The tensile strength behavior and recyclability of the paper prepared with the addition of polyamideamine-epichlorohydrin (PAE) were investigated. The dry and wet tensile strengths obtained with different PAE dosage were measured. The highest wet-to-dry strength ratio of 35% was obtained at 10 mg/g; above this addition level wet strength dropped slightly and then remained constant. The repulpability of strengthened paper was correlated directly with wet strength. The effect of electrolyte on tensile strength was also quantified by varying sodium chloride and calcium chloride concentration in the furnish stock. Without PAE, high salt concentrations (100 mM) reduced the tensile strength by 15-20%. At constant PAE addition level of 10 mg/g, low levels of salt addition (of either 10 mM NaCl or 10 mM CaCl2) slightly improved the strength; paper strength decreased at high salts concentrations. The cation valency and concentration in the process water were important variables which affected the efficiency of PAE. These results present the significance of developing sustainable wet strength agents that can be applied in demanding salty conditions while maintaining the product recyclability.