Search

Composite materials comprising a mixture of shellac resin as the matrix and cellulose as the reinforcement were developed. The influence of the reinforcement content and the concentration of additives on the mechanical performance and processing were investigated. A high content of cellulose and low concentrations of ethanol and polyethylene glycol produced biocomposites with high stress resistance and a high Young's modulus, whereas a low content of cellulose and a high concentration of additives gave samples a low Young's modulus and high elasticity. Two types of cellulose-based reinforcements with different polarity, namely, mechanically refined wood pulp and cellulose acetate butyrate particles, were compared. The efficiency of the composite over the two model reinforcements, i.e., hydrophilic and hydrophobic components, respectively, was also studied. Although particle reinforcement was easier to process and evenly dispersed into the matrix, its mechanical performance was lower compared with refined fibres. Scanning electron microscopy showed that the matrix better coated the fibres than the particles, resulting in better adhesion and mechanical performance. The morphology of reinforcement played a key role; long fibres oriented in the pulling direction ensured a better mechanical resistance than particle fillers. [ABSTRACT FROM AUTHOR]

The effect of fiber surface modification by superheated steam (SHS) treatment and fiber content (30 to 50 wt.%) was evaluated relative to the mechanical, morphology, thermal, and water absorption properties of oil palm mesocarp fiber (OPMF)/polypropylene (PP) biocomposites. SHS treatment of OPMF was conducted between 190 and 230 °C for 1 h, then the SHS-treated fiber was subjected to melt-blending with PP for biocomposite production. The biocomposite prepared from SHS-OPMF treated at 210 °C with 30 wt.% fiber loading resulted in SHS-OPMF/PP biocomposites with a tensile strength of 20.5 MPa, 25% higher than untreated-OPMF/PP biocomposites. A significant reduction of water absorption by 31% and an improved thermal stability by 8% at T5%degradation were also recorded. Scanning electron microscopy images of fractured SHS-OPMF/PP biocomposites exhibited less fiber pull-out, indicating that SHS treatment improved interfacial adhesion between fiber and PP. The results demonstrated SHS treatment is an effective surface modification method for biocomposite production. [ABSTRACT FROM AUTHOR]

The objective of this work was to study the biodegradability of polylactic acid (PLA)/paddy straw powder (PSP) biocomposites. Environmental degradation was evaluated by composting the biocomposite samples into the soil. Different techniques, including mechanical tests and scanning electron microscopy (SEM), were used to obtain a view of the degradation that occurred during the soil burial of the biocomposites. Results of the mechanical tests showed that an increasing content of PSP in the biocomposites decreased the tensile strength and elongation at break (EB), while it increased the modulus of elasticity after six months of exposure. Scanning electron microscopy on the surface after soil burial showed that the filler was poorly wetted by the matrix. This explains the reduction in tensile strength and the elongation at break after soil burial. Differential scanning calorimetry results indicated that the crystallinity of the biocomposites increased with longer composting periods. [ABSTRACT FROM AUTHOR]

One of the big global, environmental, and socioeconomic challenges of today is to make a transition from fossil fuels to biomass as a sustainable supply of renewable raw materials for industry. Growing public awareness of the negative environmental effects of petrochemical-based products adds to the need for alternative production chains, especially in materials science. One option lies in the value-added upcycling of agricultural byproducts, which are increasingly being used for biocomposite materials in transport and building sector applications. Here, sunflower by-product (obtained by grinding the stems) is considered as a source of natural fibers for engineered biocomposite material. Recent results are shown for the main mechanical properties of sunflower-based biocomposites and the socioeconomic impact of their use. This paper demonstrates that sunflower stem makes a good candidate feedstock for material applications. This is due not only to its physical and chemical properties, but also to its socioeconomic and environmental rationales. [ABSTRACT FROM AUTHOR]

In this work, the surface of oil palm mesocarp fiber (OPMF) was modified via alkaline-peroxide treatment with hydrogen peroxide under alkaline conditions. The effect of the treatment on the chemical composition and microstructure of the fiber was examined using chemical analysis, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The treatment resulted in the removal of lignin, hemicellulose, and waxy substances from the fiber and increased its surface roughness and crystallinity. The eco-friendly biocomposite was made from poly(butylene succinate) (PBS) and chemically treated fiber at a weight ratio of 30:70, and was fabricated via a melt-blending technique followed by hot-pressed moulding. The results indicated that alkaline-peroxide treatment of the fiber improved the tensile strength, tensile modulus, and elongation at break of the OPMF/PBS biocomposite by 54, 830, and 43%, respectively. The SEM analysis revealed improvement of the interfacial adhesion between the chemically treated fiber and the PBS. This work demonstrates that alkaline-peroxide treatment of fiber is beneficial prior to its use in fabricating biocomposites. [ABSTRACT FROM AUTHOR]

In this work, oil palm mesocarp fiber (OPMF) was surface-treated with varying NaOH concentrations (1, 3, 5, 7, or 9%) and soaking times (1, 2, 3, or 4 h) at room temperature aiming to enhance its adhesion to the thermoplastic matrix for biocomposite application. The biocomposites from alkali treated OPMFs and poly(butylene succinate) at weight ratios of 70:30 were fabricated by a melt blending technique and hot-pressed moulding. The results indicate that NaOH treatment removed fiber's surface waxes, hemicellulose, and lignin, and produced fiber with rough surface morphology. The tensile results showed that OPMF treated in 5% NaOH solution for 3 h produced biocomposite with enhanced tensile strength (30%), tensile modulus (105%), and elongation at break (16%), as well as reduced water absorption (15%) and thickness swelling (13%) in comparison to that of untreated OPMF. Scanning electron microscopy showed improvement of interfacial adhesion between treated fiber and poly(butylene succinate). These results suggest that NaOH treatment could be an effective form of treatment for OPMF in biocomposites materials. [ABSTRACT FROM AUTHOR]

The electrical properties of chicken feather fiber (CFF) and kenaf fiber (KF) unsaturated polyester (UP) composites have been studied with reference to fiber loading and frequency. Tests were carried out to compare the suitability of the two different composites as a dielectric material. The chicken feather fiber unsaturated polyester composite exhibited an overall lower dielectric constant, dissipation factor, and loss factor compared to the kenaf fiber unsaturated polyester composites. The values were high for the composites with fiber contents at 40%. The dielectric value increments were high at low frequencies, and they gradually reached significantly lower values at higher frequencies. Based on the results it was judged that chicken feather fiber composites would be suitable for application as high speed printed circuit board (PCB) material with good frequency stability at 1 MHz. Finally, an attempt was made to correlate the experimental values with theoretical calculations. [ABSTRACT FROM AUTHOR]

This paper demonstrates the preparation of transparent biocomposites from chitin nanofiber using a series of simple mechanical treatments after the removal of proteins and minerals. Field emission scanning electron microscopy (FE-SEM) images show that the prepared chitin nanofibers are highly uniform with a width of less than 50 nm and a high aspect ratio. Due to the nano-size, the fibers are small enough to retain the transparency of the neat polymethylmethacrylate resin. Light transmission of the obtained chitin/PMMA biocomposite was 90.2%, in comparison to the neat resin, which was 92.6%. Mechanical property tests showed that chitin nanofibers significantly improved the tensile strengths and Young's modulus of the neat PMMA, which increased from 43.8 MPa to 102 MPa and 1.6 GPa to 3.43 GPa, respectively. PMMA resin was found to be well dispersed in the biocomposite and had little effect on the tensile properties of the material. The properties mentioned above qualify the chitin nanofiber as a green and high-performance candidate having potential to be applied in next-generation optical electronic and building systems as a commercially available material. [ABSTRACT FROM AUTHOR]