Search

In order to identify faster-growing non-woody species usable for biomass and paper production, four Leucaena species (L. diversifolia, L. colinsii, L. salvadorensis and three varieties of L. leucocephala) were tested. All the Leucaena species showed a good soil and climatic adaptation to Spain Southwest except for L. salvadorensis. Studied Leucaena species showed biomass productivity ranges from 67.14 to 9.44tha−1 (o.d.b.) and 43.6 to 11.4tha−1 under Mediterranean conditions for the first and second year sprouts, respectively. The quantity of solubles and extractives shows similar values when compared with wood materials. Relatively lower lignin content in Leucaena (from 15.7% to 21.4%) species has been found with respect to other vegetal species. The α-cellulose contents (39.4–45.3%) are in the range of the normal values expected for the other non-wood raw materials. The study confirms the feasibility of organocell yield pulping process to Leucaena species. Organocell process provides an efficient delignification (kappa number 12.4 and pulp yield 42.2%) for L. leucocephala and suitably physical characteristics of paper sheet (tensile index 20.3kNm/kg for L. diversifolia). [Copyright &y& Elsevier]

Abstract: This paper examines the influence of the degree of refining of different pulps, produced from olive trimmings and eucalyptus wood, on various physical properties. Corresponding pulps were obtained by means of different cooking processes. Pulp from olive trimmings was obtained by means of an organosolv process and pulp from eucalyptus was obtained by means of a kraft process. Pulp from olive trimmings exhibited a lower specific surface area, water retention volume, breaking length, stretch and burst index, but a higher porosity, than eucalyptus pulp. On the other hand, the same degree of refining was achieved with less energy for olive pulp than for eucalyptus pulp. Mixed pulp from olive trimmings and eucalyptus provided paper sheets with acceptable physical properties but with reduced refining energy costs relative to eucalyptus pulp alone. [Copyright &y& Elsevier]

The influence of independent variables in the pulping of wheat straw by use of an ethanol–acetone–water mixture [processing temperature and time, ethanol/(ethanol + acetone) value and (ethanol + acetone)/(ethanol + acetone + water) value] and of the number of PFI beating revolutions to which the pulp was subjected, on the properties of the resulting pulp (yield and Shopper–Riegler index) and of the paper sheets obtained from it (breaking length, stretch, burst index and tear index) was examined.By using a central composite factor design and the BMDP software suite, equations that relate each dependent variable to the different independent variables were obtained that reproduced the experimental results for the dependent variables with errors less than 30% at temperatures, times, ethanol/(ethanol + acetone) value, (ethanol + acetone)/(ethanol + acetone + water) value and numbers of PFI beating revolutions in the ranges 140–180 °C, 60–120 min, 25–75%, 35–75% and 0–1750, respectively.Using values of the independent variables over the variation ranges considered provided the following optimum values of the dependent variables: 78.17% (yield), 15.21 °SR (Shopper–Riegler index), 5265 m (breaking length), 1.94% (stretch), 2.53 kN/g (burst index) and 4.26 mN m2/g (tear index).Obtaining reasonably good paper sheets (with properties that differed by less than 15% from their optimum values except for the burst index, which was 28% lower) entailed using a temperature of 180 °C, an ethanol/(ethanol + acetone) value of 50%, an (ethanol + acetone)/(ethanol + acetone + water) value of 75%, a processing time of 60 min and a number of PFI beating revolutions of 1750. The yield was 32% lower under these conditions, however.A comparison of the results provided by ethanol, acetone and ethanol–acetone pulping revealed that the second and third process-which provided an increased yield were the best choices. On the other hand, if the pulp is to be refined, ethanol pulping is the process of choice. [Copyright &y& Elsevier]