Search

Durian peel is a type of biomass derived from agricultural residues, which are found in abundant in Thailand. This study aims to investigate the thermal and chemical properties of three indigenous durian peels, namely Monthong (MDP), Puangmanee (PDP), and Bacho (BDP), as well as the characteristics of biochar and pyrolysis liquid derived from slow pyrolysis of the durian peel. MDP had the greatest volatile matter and fixed carbon content, with 73.97 and 18.43 wt%, respectively. MDP was applied for further research in order to produce biochar and pyrolysis liquid at pyrolysis temperatures of 400 and 600 °C. The maximum biochar yield was 36.01% at 400 °C, while the maximum pyrolysis liquid yield was 37.25% at 600 °C. The largest high heating value of biochar (24.48 MJ kg−1) was obtained at 600 °C more than the high heating value of feedstock (14.32 MJ kg−1). Biochar obtained at 400 °C can be categorized as fertilizer class 4, while biochar obtained at 600 °C can be classified as carbon storage class 2 using the IBI biochar classification tool. The quality of the pyrolysis liquid was determined to be of 3.14 pH and 1.052 g mL−1 specific gravity at a pyrolysis temperature of 600 °C, which meets Thailand standards. As a result, both 400 °C and 600 °C pyrolysis liquids produced significant chemicals that are employed in a variety of industries. Consequently, this research is strongly recommended to be expanded to produce high-quality durian peel biochar and pyrolysis liquid. [Display omitted] • Comprehensive physical, chemical, thermal properties of durian peels were explored. • Durian peel biochar can be categorized by the IBI as carbon storage class 2. • The biochar can be classified by the IBI as a high fertilizer class 4. • Pyrolysis liquid derived from the durian peel meet Thailand standards. • 81 main compounds with essential chemicals were detected in the pyrolysis liquids. [ABSTRACT FROM AUTHOR]

The in-field burning of sugarcane leaf residues presents a major environmental and health burden in Thailand. In this study, sugarcane leaves were converted into a biochar-based slow release phosphorus (P) fertilizer via pyrolysis at 600 °C, and the influence of pre- and post-pyrolysis treatment on the P loading and release was investigated. The sugarcane leaves were pre-treated with an alkaline (diammonium phosphate, DAP) or an acidic P source (phosphoric acid, PA), with or without addition of MgO. Additionally, the biochar was post-treated with DAP to increase the P loading. Extraction of P in DI water and 2% formic acid were used as indicators for potential slow release. The microporous biochars had a specific surface area of 69–333 m2 g−1 and pre-treatment resulted in a P content of 34–82 g kg−1. When MgO was included in the pre-treatment, XRD analysis confirmed formation of crystalline Mg 2 P 2 O 7 , irrespective of the P source. This Mg 2 P 2 O 7 was responsible for slow P release in DI water over 240 h via a dissolution-controlled process. Post-treatment with DAP increased the P loading to 156 g kg−1 in the form of water-soluble monoammonium phosphate (MAP), which did not contribute to slow release. The tunable P release via combinations of pre- and post-pyrolysis treatment makes these engineered biochars attractive as P sources for crops and presents an attractive solution to mitigate in-field sugarcane residue burning. [Display omitted] • P-loaded biochar was prepared by co-pyrolysis of sugarcane leaves with P + MgO. • Addition of MgO in pre-pyrolysis treatment results in slow release of P. • The slow P release is controlled by dissolution of Mg 2 P 2 O 7. • Post-treatment with DAP increases water-soluble P but not slow-release P. [ABSTRACT FROM AUTHOR]