Search

Airborne particulate matter (PM) is of great concern in the modern-day atmosphere owing to its association with a variety of health impacts, such as respiratory and cardiovascular diseases. Of the various size fractions of PM, it is the finer fractions that are most harmful to health, in particular ultrafine particles (PM0.1; UFPs), with an aerodynamic diameter ≤ 100 nm. The smaller size fractions, of ≤2.5 µm (PM2.5; fine particles) and ≤0.1 µm (PM0.1; ultrafine particles), have been shown to have numerous linkages to negative health effects; however, their collection/sampling remains challenging. This review paper employed a comprehensive literature review methodology; 200 studies were evaluated based on the rigor of their methodologies, including the validity of experimental designs, data collection methods, and statistical analyses. Studies with robust methodologies were prioritised for inclusion. This review paper critically assesses the health risks associated with fine and ultrafine particles, highlighting vehicular emissions as the most significant source of particulate-related health effects. While coal combustion, diesel exhaust, household wood combustors' emissions, and Earth's crust dust also pose health risks, evidence suggests that exposure to particulates from vehicular emissions has the greatest impact on human health due to their widespread distribution and contribution to air pollution-related diseases. This article comprehensively examines current sampling technologies, specifically focusing on the collection and sampling of ultrafine particles (UFP) from ambient air to facilitate toxicological and physiochemical characterisation efforts. This article discusses diverse approaches to collect fine and ultrafine particulates, along with experimental endeavours to assess ultrafine particle concentrations across various microenvironments. Following meticulous evaluation of sampling techniques, high-volume air samplers such as the Chem Vol Model 2400 High Volume Cascade Impactor and low-volume samplers like the Personal Cascade Impactor Sampler (PCIS) emerge as effective methods. These techniques offer advantages in particle size fractionation, collection efficiency, and adaptability to different sampling environments, positioning them as valuable tools for precise characterisation of particulate matter in air quality research and environmental monitoring. [ABSTRACT FROM AUTHOR]

This paper is the first to examine the operation of the HawkEye satellite in the presence of dust aerosol. The study region is the Black Sea. Dust transport dates were identified using visual inspection of satellite imagery, back-kinematic HYSPLIT trajectory analysis, CALIPSO aerosol stratification and typing maps, and the global forecasting model SILAM. In a comparative analysis of in-situ and satellite measurements of the remote sensing reflectance, an error in the atmospheric correction of HawkEye measurements was found both for a clean atmosphere and in the presence of an absorbing aerosol. It is shown that, on average, the dependence of the atmospheric correction error on wavelength has the form of a power function of the form from λ−3 to λ−9. The largest errors are in the short-wavelength region of the spectrum (412–443 nm) for the dust and dusty marine aerosol domination dates. A comparative analysis of satellite and in situ measurements of the optical characteristics of the atmosphere, namely the AOD and the Ångström parameter, was carried out. It is shown that the aerosol model used by HawkEye underestimates the Angström parameter and, most likely, large errors and outliers in satellite measurements are associated with this. [ABSTRACT FROM AUTHOR]

In engineering pulse-jet dust collector applications, the filtration area and injection pressure are chosen mostly based on experience. The peak pressure is tested under different injection pressures and filtration areas controlled by an electromagnetic valve, and then comprehensively analyzes the effects of dust intensity, uniformity, and air consumption on dust cleaning to obtain a better filtration area controlled by an electromagnetic valve and injection pressure. The results show that considering the uniformity and intensity of dust cleaning, the filtration area of 33 m2 under the injection pressure of 0.4 MPa should be preferentially selected, with a standard deviation of 0.246 and a variance of 0.061. The filtration area of 27 m2 under the injection pressure of 0.3 MPa should be preferentially selected considering the unit air consumption, uniformity, and intensity of dust cleaning, the standard deviation of 0.252, and the variance of 0.064. The paper presents a theoretical foundation for selecting the optimal injection pressure and filter area regulated by an electromagnetic valve in pulse-jet dust collector systems. [ABSTRACT FROM AUTHOR]

Due to the advantages of a short cycle, low investment and low energy consumption per ton of steel, short-process electric furnace steelmaking is about to welcome a golden period of rapid development in China. During the operation of the electric furnace, a large amount of smoke and dust is generated. Most studies focus on organized emissions, and the impact of unorganized emissions in workshops on the environment cannot be ignored. This paper evaluates the thermal environment in the electric furnace steelmaking workshop based on the analytic hierarchy process and obtains the influence weight of the fugitive emission location. The mass concentration of dust at each measuring point increased by 1.17 mg/m3 on average, and the concentration of unorganized emission dust near the outlet was 23.572 mg/m3. The numerical simulation calculation model is established by the CFD method, a fixed initial jet velocity is set, the initial velocity of the ladle soot plume is changed, and the inclination angle, arrangement height and dust removal air volume of the dust hood are respectively adjusted in different tapping periods. The impact of simulation on the efficiency of dust collection for different dust removal hood configurations was investigated, considering variations in inclination angle, arrangement height and dust removal airflow. The optimal structural parameters for the dust removal hood were determined to be an inclination angle of 60° and an arrangement height of 2.4 m, and an optimal dust removal airflow was determined to be 110,000 m3/h. This study provides a theoretical foundation for engineering practice. [ABSTRACT FROM AUTHOR]

Aerosols, both natural and anthropogenic, are an important but complex component of the Earth's climate system. Their net impact on climate is about equal in magnitude to that of greenhouse gases but can vary significantly by region and type. Understanding and quantifying these aerosol effects is critical for accurate climate modeling and for developing strategies to mitigate climate change. In this paper, we utilize AERONET (Aerosol Robotic NETwork) data from 10 stations situated in the dust belt region to characterize aerosol properties essential for climate change assessment. Aerosol optical depth (AOD) data at 500 nm and Ångström exponent (α) data at the pair of wavelengths of 440 and 870 nm (α440-870) in the study region are analyzed to discriminate among different types of aerosols. The annual and monthly variabilities in AODs are analyzed to see the aerosols trend in the study region. In addition, the AOD and α440-870 data are utilized in order to determine different aerosol types during the period of study. Furthermore, the correlation coefficient between AODs and various meteorological parameters (temperature, wind speed, wind direction, relative humidity, and visibility) is analyzed. The results of the study indicate that Tamanrasset (2.49%), KAUST (1.29%), Solar Village (1.67%), and Dalanzadgad (0.64%) indicate an increasing trend, while Cairo (−0.38%), Masdar (−2.31%), Dushanbe (−1.18%), and Lahore (−0.10%) indicate a decreasing trend in AODs during the study period. Similarly, the results of characterizing aerosol types show that the highest percentage of desert dust aerosols (68%), mixed aerosols (86%), and biomass burning aerosols (15%) are found over Tamanrasset, Lahore, and Dalanzadgad AERONET stations. The study revealed a strong correlation between AODs and visibility, a moderate correlation with temperature, and a low correlation with other meteorological parameters (wind speed, wind direction, and relative humidity) in the study region. The results of the study are very encouraging and enhance our confidence in using historical AERONET data to improve our understanding of atmospheric aerosols' characteristics. [ABSTRACT FROM AUTHOR]

The criteria-based sand and dust weather determination method has the problem ofbeing a cumbersome and time-consuming process when processing a large amount of raw data, and cannot avoid the problems of repeatability and reproducibility. On the basis of statistical analysis of the air automatic monitoring data in the cities affected by sand and dust, this paper proposes a k-means optimization algorithm (MDPD-k-means) based on maximum density and percentage distance, which can quickly filter the characteristic data of sand and dust in a short time, and identify the days affected by sand and dust. This method effectively improves the data processing efficiency, solves the problems of poor reproducibility and large artificial error of traditional methods, and can support the business application of sand and dust data elimination. This paper uses the method to identify the sand and dust data of 10 cities in Shaanxi Province from 2016 to 2022, determines a total of 1107 sand and dust days, and points out that the number of days affected by sand and dust is increasing year by year. After excluding the effect of sand and dust, the urban PM10 concentration decreases by 18.42~1.41% respectively, which provides important data information for accurately evaluating the effectiveness of air pollution prevention and control. [ABSTRACT FROM AUTHOR]

This report provides a review of several measurement studies and campaigns focusing on road dust resuspension (RDS), which is becoming an important source of ambient particulate matter (PM) concentrations. There is a growing requirement from stakeholders, policy makers and scientists for gathering additional data around RDS, since there is a lack of well-established methodologies or those developed for measuring or modelling this source of emissions are not very recent. Moreover, conventional inventory methodologies are not available for this source of emissions, and it is not yet covered in the UK's National Atmospheric Emissions Inventory (NAEI) neither in the inventory guidebooks at European level. Based on the available literature and models, this paper also seeks to provide some preliminary considerations whether an approach can be tailored for application in air quality models used for modelling ambient PM concentrations in the UK in a consistent manner and demonstrated using a state-of-art air quality modelling tool, namely RapidAir®. The impact of including resuspension emissions on roadside concentrations was modelled in a UK case study with the greatest increases in modelled road PM10 concentrations observed on or near the road surface. The paper concludes with recommendations for longer-term implementation of the proposed improvements such as investigation of the temporal effects of RDS on PM levels; of the influence of different type of tyre materials and mixture (e.g., composition) and designs (e.g., shape, dimensions and tread); and influence of different existing pavements or of new road surface types. [ABSTRACT FROM AUTHOR]

During the second half of August 2022, a dust intrusion event occurred when dust that originated in the dry regions of the Kalmyk steppe (located in Russia, northeast of the Black Sea, north of Georgia, and northwest of the Caspian Sea) and the Precaspian plain was transported over the eastern region of Romania. The arid soil found in these areas can be attributed to an extended period of intense drought, with notable instances occurring in 2002, 2003, 2015, and 2018. This situation was further intensified by heatwaves experienced in May and June of 2022. The dust event was captured in MODIS images. In addition, smoke trains originating from fires in the north of the Azov were detected, but these did not reach Romania. Optical parameters from AERONET were used to confirm the dust event. To determine the trajectory of the particles, the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model was used in this paper. The ensemble median model was used to highlight the presence and concentration of dust in the eastern part of Romania. Aerosols were detected between 0 and 4 km, according to radar and ceilometer data from the REXDAN cloud remote sensing facility in Galați, Romania. This dust intrusion event was the result of the dominant easterly circulation caused by the extension of the East European High to the northeast of the continent, which transported the dust towards the eastern part of Romania for more than 2 days. Moreover, the torrential rains between 22 and 24 August did not clear the atmosphere of dust, since the intense easterly circulation kept carrying the dust into the Moldavian area. [ABSTRACT FROM AUTHOR]

In this paper, individual particle analysis by automated scanning electron microscopy (SEM) coupled with energy-dispersive X-ray (EDX) was used to assess the size-resolved information of composition, size distribution, complex refractive index, and mixing state of mineral dust aerosol particles collected using different passive and active samplers. In the study, over 120,000 particles from 53 samples were analyzed. Results show that dust particles are the dominating mineral particle type during this campaign, comprising different classes of silicates, Si-rich (quartz-like), Ca-rich (calcite-like), CaMg-rich (dolomite-like), and CaS-rich (gypsum-like). The results also show that there is no significant difference in composition between suspended and deposited dust particles. By using the particle composition, the size-resolved complex refractive index of dust particles was calculated. The real part of the refractive index varied between 1.71 and 1.53 for wavelengths in the range of 370 to 950 nm. The imaginary part of the refractive index, determined mostly by iron oxide, varied between 3.28 × 10 − 4 and 7.11 × 10 − 5 for wavelengths ranging from 250 nm to 1640 nm. In addition, the refractive index values showed a slight decrease with increasing particle size. We also analyzed the potential for buffering of the acid mobilization of iron by other dust compounds. For particles which contain both iron (Fe) and (unprocessed) calcium (Ca), acids that are able to dissolve insoluble Fe particles can react with the Ca particles before reacting with Fe, but eventually, with longer processing time, the Fe particles could be processed. By analyzing the ratio of sulfate mass to the total aerosol mass of individual particles, the mixing state of sulfate particles to the total dust particles was investigated. The analysis showed that the finer dust particles were associated with higher content of sulfate, while the coarse dust particles correspond to lower sulfate contents, revealing that only fine mode sulfate is more internally mixed with mineral dust aerosol particles. [ABSTRACT FROM AUTHOR]

This paper aims to analyze the significant changes in atmospheric aerosol characteristics during the extreme aerosol outbreak event in April 2019 in the atmosphere over Cyprus in the Eastern Mediterranean. We study the aerosol optical depth (AOD), Ångström exponent (AE), single-scattering albedo, refractive index, size, and vertical distribution of aerosol particles during the event of intense aerosol advection in detail. For this purpose, we used the ground-based observations of the sun-photometer AERONET Nicosia station, lidar measurements, and back trajectories of air movements calculated using the Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT). To compare with background aerosol load conditions during the year, the available data of AOD and AE were used from the observations at the Nicosia AERONET site in the 2015–2022 period. On 23–25 April 2019, strong aerosol advection over Nicosia was detected according to lidar and sun-photometer observations. On 25 April 2019, the day with the largest aerosol contamination, the AOD value exceeded 0.9 at λ = 500 nm. Analysis of the optical and microphysical characteristics during the extreme event supported that the aerosol advection consists of mainly Saharan dust particles. This assumption was confirmed by the AOD versus AE variations, single-scattering albedo, refractive index, and size distribution retrievals, as well as lidar data and HYSPLIT backward trajectories, where air masses containing dust particles came mostly from North Africa. The analysis shows that the April 2019 event was one of the strongest aerosol surges that regularly take place in springtime in the atmosphere over Cyprus. The noticeable reduction in the effective radiative forcing caused by increasing aerosol amount during the aerosol dust outbreak was revealed. [ABSTRACT FROM AUTHOR]

Particle emissions into the atmosphere can cause extensive damage to the environment and human health. To improve the efficiency in the collection of submicronic particles, new filtration media appeared on the market due to new textile technologies and equipment, such as filter media developed with polytetrafluoroethylene (PTFE) membranes; however, these are more expensive. A filter coating technique called precoating is a more economical alternative that could enhance filtration efficiency. This paper aimed to evaluate the operational parameters of precoating for micro- and nanoparticle filtration and compare the results with those obtained from the PTFE membrane. For this purpose, filtration cycles were performed, using precoated polyester with hydrated lime and dolomitic limestone, polyester with a PTFE membrane, and steel industry ultrafine dust. The results showed that the precoated polyester had a longer cycle duration and lower pressure drop than the polyester with a PTFE membrane. Therefore, precoating was shown to be a great alternative to be used in bag filters in steel mills because it presented high collection efficiency for submicronic particles, in addition to increasing the bag lifespan with less energy expenditure. [ABSTRACT FROM AUTHOR]

The melting behavior of glaciers on and around the Tibetan Plateau is strongly influenced by their albedo. In this paper, we report continuous observations made on the Qiangtang (QT) No. 1 Glacier, located in the central Tibetan Plateau, during its 2013–2015 melting seasons. Surface snow on the QT No. 1 Glacier mainly had a dust content less than 600 ppm and a black carbon (BC) content less than 10 ppb. A strong negative correlation was observed between albedo and dust content up to a threshold concentration of 1000 ppm, although albedo remained constant when dust concentrations increased above this value. The radii of snow particles showed a log-normal distribution that had a mean value of ~500 μm, but maximum and minimum values of 2539 μm and 40 μm, respectively. Snow density showed a normal distribution with a total range of 193–555 kg/m3, although most snow had a density of 400 kg/m3. Snow, ice, and aerosol radiative (SNICAR) simulations showed that dust and BC in the surface snow of the QT No. 1 Glacier reduced the snow and ice albedo by 5.9% and 0.06%, respectively, during the ablation season in 2015; however, the simulated particle impact was greater than the albedo reduction measured from field data. We interpret that dust has played a significantly more important role in melting of the QT No. 1 Glacier than BC over the study period, which is mainly due to the scarcity of human activities in the region and the low concentration of BC being produced. [ABSTRACT FROM AUTHOR]

The characteristics, distributions, and trends of the aerosol optical depth (AOD) and dust aerosol optical depth (DAOD) of three major concentrating solar power (CSP)-plant project areas (Hami, Turpan, and Ruoqiang) in Xinjiang, China were investigated and analyzed during 1980–2022 using the Modern-Era Retrospective analysis for Research and Applications Version 2 (MERRA-2) reanalysis products. The monthly variation, seasonal variation, inter-annual variation, distributions of AOD and DAOD, and proportions of dust in the aerosols in these three CSP-plant project areas were computed and analyzed. Overall, the annual mean AOD at 550 nm in the Turpan project area was the highest (0.20–0.36), while Ruoqiang had the lowest annual mean AOD at 550 nm (0.13–0.30), and the annual mean AOD at 550 nm in Hami was distributed between 0.17 and 0.33. After 2010, the change in the rate of the annual mean AOD showed an overall downward trend in Hami and Ruoqiang, indicating that the atmospheric environmental changes in both areas were more favorable for the operation of CSP plants. In the project areas of Hami, Turpan, and Ruoqiang, more than 90% of the AOD values were mainly in ranges 0.10–0.30, 0.10–0.35, and 0.05–0.30, respectively. As expected, the AOD values in spring and summer were significantly higher than those in autumn and winter in the three study areas. In spring, the dust contents (i.e., ratios of DAOD to AOD) were the highest, accounting for 64% (Hami), 67% (Turpan), and 69% (Ruoqiang) of the total aerosol contents. In all three areas, the proportions of dust in aerosols in spring have shown an increasing trend since 2000, suggesting that the negative impact of the dust on the power generation efficiency in these areas has gradually been increasing. Therefore, it is recommended that the CSP plants in Hami, Turpan, and Ruoqiang develop a strategy for cleaning heliostats, especially in spring, to reduce the impact of dust adhesion on the efficiency of the CSP plants. [ABSTRACT FROM AUTHOR]

In this paper, the atmospheric environmental corrosion grade of substations in 11 prefecture level cities in Shanxi Province is evaluated through a metal hanging sheet experiment. Combined with the main environmental factors, such as temperature, relative humidity, and the concentration of main pollution factors, such as SO2, Cl−, dust, etc., the influence of various factors on the corrosion of transmission and transformation equipment is analyzed, and the corresponding anti-corrosion measures are put forward. [ABSTRACT FROM AUTHOR]

Turkey is located in the heart of complex transition geography between Eurasia and the Middle East. In the grand scheme, the so-called eastern Mediterranean Basin is located almost in the middle of the dusty belt, and is a hot spot of climate change. The downstream location of dust-carrying winds from close desert sources reveals Turkey as an open plane to particulate matter exposure throughout the year. In order to clarify this phenomenon, this paper aims to determine the desert dust climatology of Turkey via CALIPSO onboard Lidar. This prominent instrument enables us to understand clouds, aerosols and their types, and related climatic systems, with its valuable products. In this study, a 9-year CALIPSO-derived pure dust product dataset was formed to explain horizontal and vertical distributions, transport heights and case incidences. The results indicated that the pure dust extinction coefficient increased as the location shifted from west to east. Moreover, in the same direction of west to east, the dominant spring months changed to summer and autumn. Mountain range systems surrounding Anatolia were the main obstacles against lofted and buoyant dust particles travelling to northern latitudes. Even if high ridges accumulated mass load on the southern slopes, they also enabled elevated particles to reach the ground level of the inner cities. [ABSTRACT FROM AUTHOR]

The detection and evaluation of biomass burning and dust events are critical for understanding their impact on air quality, climate, and human health, particularly in the Mediterranean region. This research pioneers an innovative methodology that uses Sentinel-2 multispectral (MS) imagery to meticulously pinpoint and analyze long-transport dust outbreaks and biomass burning phenomena, originating both locally and transported from remote areas. We developed the dust/biomass burning (DBB) composite normalized differential index, a tool that identifies clear, dusty, and biomass burning scenarios in the selected region. The DBB index jointly employs specific Sentinel-2 bands: B2-B3-B4 for visible light analysis, and B11 and B12 for short-wave infrared (SWIR), exploiting the specificity of each wavelength to assess the presence of different aerosols. A key feature of the DBB index is its normalization by the surface reflectance of the scene, which ensures independence from the underlying texture, such as streets and buildings, for urban areas. The differentiation involves the comparison of the top-of-atmosphere (TOA) reflectance values from aerosol events with those from clear-sky reference images, thereby constituting a sort of calibration. The index is tailored for urban settings, where Sentinel-2 imagery provides a decametric spatial resolution and revisit time of 5 days. The average values of DBB achieve a 96% match with the coarse-mode aerosol optical depths (AOD), measured by a local station of the AERONET network of sun-photometers. In future studies, the map of DBB could be integrated with that achieved from Sentinel-3 images, which offer similar spectral bands, albeit with much less fine spatial resolution, yet benefit from daily coverage. [ABSTRACT FROM AUTHOR]

The dust storms with local and non-local dust sources mostly affect Khuzestan province in southwest (SW) Iran. In this study, the role of the low-level jet in the activation of the internal dust events in SW Iran during two severe dust cases was investigated. For this purpose, the fifth-generation ECMWF reanalysis for the global climate and weather (ERA5) data was used to identify the synoptic patterns and the low-level jet (LLJ) characteristics in the study area. Furthermore, the images of the moderate resolution imaging spectroradiometer (MODIS) sensor, the outputs of the hybrid single-particle Lagrangian integrated trajectory (HYSPLIT) model, and a weather research and forecasting model coupled with chemistry (WRF-Chem) were used to investigate the propagation and transport of the dust particles. The results of the synoptic analysis in both dust cases show the simultaneous occurrence of the divergence zone associated with cyclonic curvature in the subtropical jet stream (STJ) at 300 hPa, causing convergence at 925 hPa, upward motion, and the development of low surface pressure in SW Iran. Examining the vertical wind profile shows the existence of the maximum horizontal wind speeds of 975 to 875 hPa, along with the positive and negative shear below and above it, respectively, which emphasizes the existence of the LLJ and its role in local dust emission. The results of the comparison between the satellite images, WRF-Chem, and HYSPLIT model outputs show the formation and transportation of dust particles from the inner regions of Khuzestan in SW Iran. The horizontal dust surface distribution, vertical raised dust mass, and kinetic energy transfers are well simulated by the WRF-Chem model when LLJ broke at 09:00 to 12:00 UTC. The most important finding of this research is that, for the first time, the role of low-level jet is investigated in the activation of internal dust events in SW Iran. [ABSTRACT FROM AUTHOR]

Dust storms and wildfires occur frequently in south-eastern Australia. Their effects on the ecology, environment and population exposure have been the focus of many studies recently. Dust storms do not emit ground-sequestered carbon, but wildfires emit significant quantities of carbon into the atmosphere. However, both natural events promote phytoplankton growth in water bodies because carbon, and other trace elements such as iron, deposit on the surface water of oceans. Carbon dioxide is reabsorbed by phytoplankton via photosynthesis. The carbon balance cycle due to dust storms and wildfires is not well known. Recent studies on the carbon emission of the 2019–2020 summer wildfires in eastern Australia indicated that this megafire event emitted approximately 715 million tonnes of CO2 (195 Tg C) into the atmosphere from burned forest areas. This study focusses on the association of dust storms and wildfires in southeastern Australia with phytoplankton growth in the Tasman Sea due to the February 2019 dust storm event and the 2019–2020 Black Summer wildfires. Central Australia and western New South Wales were the sources of the dust storm emission (11 to 16 February 2019), and the Black Summer wildfires occurred along the coast of New South Wales and Victoria (from early November 2019 to early January 2020). The WRF-Chem model is used for dust storm simulation with the AFWA (Air Force Weather Agency of the US) dust emission version of the GOCART model, and the WRF-Chem model is used for wildfire simulation with FINN (Fire Emission Inventory from NCAR) emission data. The results show the similarities and differences in the deposition of particulate matter, phytoplankton growth and carbon reabsorption patterns in the Tasman Sea from these events. A higher rate of deposition of PM2.5 on the ocean surface corresponds to a higher rate of phytoplankton growth. Using the WRF-Chem model, during the 5-day dust storm event in February 2019, approximately ~1230 tons of total dust was predicted to have been deposited in the Tasman Sea, while ~132,000 tons of PM10 was deposited in the early stage of the wildfires from 1 to 8 November 2019. [ABSTRACT FROM AUTHOR]

An integrated morphological and chemical analysis of Arctic aerosols was undertaken for Icelandic dust and Svalbard aerosols to be compared by scanning electron microscopy coupled with EDS microanalysis (SEM–EDS) via imaging and chemical analysis techniques. Results of the characterization of the particles from both surface sediments and suspended dust from desert areas in Iceland confirmed that volcanic glass is an excellent marker of Icelandic dust origin. Classification diagrams of particle chemical composition clearly distinguished the volcanic glass particles from the local surface sediments at Hornsund, Svalbard. In the same diagrams, a few particles were found in the aerosols from Hornsund which were morphologically and chemically similar to the Icelandic volcanic glass particles. Such properties, in principle, cannot be considered exclusive to volcanic glass. However, since Iceland is the largest and the most active source of long-range transported dust in the northern European high latitudes, and air mass trajectories reaching Hornsund did, actually, pass Iceland before the aerosol collection in the period under consideration, these particles likely originated in Iceland. On the other hand, the comparison with local and Icelandic sediments revealed the presence in the aerosols from Hornsund of particle types that cannot be attributed to either local or Icelandic dust. This observation highlights the possibility of extending and validating the application of the proposed geochemical criterion to different dust sources across the Arctic and the sub-Arctic, provided a consistent geochemical databank of representative dust sources from these areas is arranged. [ABSTRACT FROM AUTHOR]

Two severe dust storm (DS) events (15–17 March and 28–29 March) hit northern China in 2021 consecutively. The lower atmospheric vertical dynamic and thermal structures during the two cases were compared using the ground-based sensor data from the microwave radiometer and radar wind profiler, combined with the environmental and meteorological observations data in Jinan, China. It was found that both cases occurred under the background of cold vortexes over northeastern China. The dust was transported through the cold air on the northwest route. During the dust period, 2–3 km was the west or northwest airflow, and below 2 km was the northeast wind. The variation in the dynamic structure determined the duration of the DS. During the DS maintenance phase, the vertical wind shear (VWS) below 3 km measured approximately 10 m∙(s∙km)−1. The increased VWS during the dust intrusion period facilitated the transportation of dust. In contrast, the more significant VWS was not conducive to the maintenance of DS, and the shift to south wind control in the upper middle layer indicated the weakening of DS. In both cases, we observed a cliff-like decrease in relative humidity as a prominent indicator of dust outbreaks, occurring approximately 2–5 h beforehand. The diurnal difference between the vertical temperature and relative humidity during the dust maintenance period was found to be insignificant. [ABSTRACT FROM AUTHOR]

The mechanism of aerosol pollution transport remains highly elusive owing to the myriad of influential factors. In this study, ground station data, satellite data, ground-based LiDAR remote sensing data, sounding data, ERA5 reanalysis and a backward trajectory model were combined to investigate the formation process and optical properties of winter aerosol pollution in Beijing and surrounding areas. The analysis of ground station data shows that compared to 2019 and 2021, the pandemic lockdown policy resulted in a decrease in the total number of pollution days and a decrease in the average concentration of particulate matter in the Beijing area in 2020. The terrain characteristics of the Beijing-Tianjin-Hebei (BTH) made it prone to northeast and southwest winds. The highest incidence of aerosol pollution in Beijing occurs in February and March during the spring and winter seasons. Analysis of a typical heavy aerosol pollution process in the Beijing area from 28 February to 5 March 2019 shows that dust and fine particulate matter contributed to the primary pollution; surface air temperature inversion and an average wind speed of less than 3 m/s were conducive to the continuous accumulation of pollutants, which was accompanied by the oxidation reaction of NO2 and O3, forming photochemical pollution. The heavy aerosol pollution was transmitted and diffused towards the southeast, gradually eliminating the pollution. Our results provide relevant research support for the prevention and control of aerosol pollution. [ABSTRACT FROM AUTHOR]

Windblown dust aerosol plays an important role in marine ecosystems once they are deposited and dissolved. At present, methods for estimating the deposition flux are mainly limited to direct measurements or model outputs. Additionally, satellite remote sensing was often used to estimate the integral dust column concentration (DCC). In this paper, an algorithm is developed to estimate the mass deposition fluxes of Asian dust by satellite. The dust aerosol is identified firstly and then the DCC is derived based on the relationships between the pre-calculated lookup table (LUT) and observations from Japanese geostationary Multi-functional Transport Satellites (MTSAT). The LUT is built on the dust cloud and surface parameters by a radiation transfer model Streamer. The average change rate of deposition is derived, which shows an exponential decay dependence on transport time along the pathway. Thus, the deposition flux is acquired via integrating the hourly deposition. This simple algorithm is applied to a dust storm that occurred in the Bohai Sea and Yellow Sea from 1 to 3 March 2008. Results indicate that the properties of the dust cloud over the study area changed rapidly and the mass deposition flux is estimated to be 2.59 Mt. [ABSTRACT FROM AUTHOR]

Regional air quality and major sources can be reflected by dust. 87 dust samples in Nanchang (four residential areas and three roadside points) were collected, with particle size and carbon components determined to discuss the distribution characteristics and the sources. The distribution of dust particle size in different sampling areas was similar, composed mainly of particles larger than 10 μm (over 69.8%). Dust particle size showed a decreasing trend with increasing horizontal distance from the main road and vertical height from the ground. EC in road dust was higher than that in residential dust. EC outdoors was higher than EC indoors in the same area. OC in indoor dust was higher than that in atmospheric dust when there were obvious indoor OC emission sources. The main carbon fractions in residential dust were OC3 and EC1, and in road dust were EC2 and OC3. The distribution of carbon fractions showed that OC3 and EC2 were mainly affected by human activities and motor vehicle emissions, respectively. The ratio of OC/EC and SOC in dust decreased from autumn to winter. SOC in the dust of Nanchang was at a medium level compared to other cities/regions around world. Clustering analysis and principal component analysis indicated that combustion sources (coal and biomass combustion, etc.), motor vehicle exhaust sources (gasoline and diesel vehicles), and human sources (cooking fumes, cigarette smoking, etc.) were the main contributors to the carbon components in dust. [ABSTRACT FROM AUTHOR]

Dust storms are one of the major environmental hazards affecting the Middle East countries, and largely originate in vast deserts and narrow dried lake beds. This study analyzes the inter-annual variation in dust weather conditions from 2000 to 2020 using data obtained from ten meteorological stations located around dried (completely or partly) lakes in Northwest (Urmia Lake) and South (Bakhtegan Lake) Iran. Since the wind regime is one of the most important factors controlling dust emissions in the dust source areas, wind speed simulations from the Weather Research and Forecasting (WRF) Model for 134,113 grid points covering the Middle East area, with a resolution of 5 km, were analyzed and compared with wind measurements at the stations around Urmia and Bakhtegan Lakes from 2005 to 2015. The analysis shows that the annual number of dust days was highly variable, presenting a significant increase at the stations around Urmia Lake during 2008–2011 and at the stations around Bakhtegan Lake in 2007–2012. Eleven years of WRF simulations of the mean diurnal wind patterns revealed that the highest 10 m wind speed occurred mostly around the local noon (12 to 15 UTC), generally coinciding with the majority of the reported dust codes within this time frame, as a result of the association between wind speed and dust emissions (dust weather conditions) around these lake basins. Consequently, accurate wind simulation has high importance for unbiased numerical prediction and forecasting of dust conditions. The comparison between the measured mean monthly 10 m wind speed and WRF-simulated 10 m wind speed revealed that the model overestimated wind data in all the stations around the Bakhtegan Lake but performed better at reconstructing the wind speeds at stations around Urmia Lake. Furthermore, notable differences were observed between measured and simulated wind directions, thus leading to uncertainties in the simulations of the dust-plume transport. [ABSTRACT FROM AUTHOR]

In June 2020, a record-breaking Saharan dust storm, known as the "Godzilla" extreme event, caused significant dust transport from the Sahara Desert across the Atlantic Ocean to the United States. Based on satellite observations, the magnitude of aerosol optical depth (AOD) has consistently remained highest over the Atlantic Ocean for the past 18 years. This study uses satellite observations (including MODIS and CALIOP) and MERRA-2 reanalysis products to investigate the relationships between dust and marine clouds. During this extreme event, the concentration of AOD exhibits a synchronous anomaly with the cloud fraction (CF). Principal components analysis (PCA) results show that the enhanced temperature and specific humidity near the surface contribute the most to cloud development over the tropical Atlantic Ocean. Despite the reduced sensitivity of CF to aerosols, the semi-direct effect of dust can still play a crucial role during this extreme dust storm. We found that the presence of absorbing aerosols above the cloud layers warms the air, accompanied by an enhancement of surface moisture, thereby benefiting low-level cloud coverage. [ABSTRACT FROM AUTHOR]

The transport and deposition of atmospheric particulate matter have attracted significant attention recently due to the increasing frequency of extreme disaster events, such as dust storms, volcanic eruptions, and extensive forest fires. The size distribution of the transported material and the conditions of the land–air interface are dominant factors in comprehending the detrimental potential of atmospheric particulate matter. However, it is still a challenge to understand the mechanism of dust deposition, especially over complex terrain. In an effort to investigate the deposition characteristics of particles over complex terrain, a series of experiments were conducted in a multifunctional environmental wind tunnel. The results show that the wind speed directly above the top of the mild slope model is significantly greater than that in the steep slope model, which indicates that a steep slope has a greater blocking effect on wind fields. At low wind speeds, the average wind speed at the top of the mild slope model is 17.8% higher than that at the top of the steep slope model, and at high wind speeds the average wind speed at the top of the mild slope model is 8.6% higher than that at the top of the steep slope model. The influence trend of the steep slope model and the combination model is basically the same, with both decreasing first and then increasing with the direction of wind velocity. The amount of surface deposition is greatly affected by the location of the feeding point and the microscale characteristics of the surface. In the steep slope model, the deposition is mainly distributed on the windward side, while the leeward side has a small amount of deposition. In the mild slope model, particles are deposited not only on the windward side, but also on the leeward side. The average rate of decline in deposition flux in the steep slope model is 88.4% and 75.1% in the mild slope model. The use of the combination model reduces the particle concentration at the back end compared with the single model. In three different models, the deposition on the windward side was shown to be significantly greater than that on the leeward side of the model. Our work increases understanding of the deposition of coarse dust particles over complex terrain and provides basic data for improving the accuracy of large-region particle transport and deposition simulations. [ABSTRACT FROM AUTHOR]

To further promote dust control efforts in Chinese open-pit coal mines, this study focuses on the research of coal dust and rock dust produced by different explosions in the Haerwusu open-pit coal mine in China. By investigating the relationship between the physical and chemical characteristics of dust particles from explosions in open-pit mines and the wetting properties of dust, the main factors influencing the wetting properties of explosive dust are identified. This provides a theoretical basis for subsequent dust control work in open-pit coal mines. Simultaneously, to formulate more effective dust suppressants and reduce explosive dust pollution, this study conducts experiments on the surface tension, contact angles, and complex solution compatibility to select suitable surfactants. Ultimately, the effectiveness of the dust suppressants is evaluated through permeability experiments and indoor dust suppression experiments. The research findings are as follows: (1) The significant factors affecting the wetting properties of coal dust are the fixed carbon content and D50, while the significant factor affecting the wetting properties of rock dust is D50. (2) The formulated dust suppressants can increase the permeation height of coal dust by at least 10 times, increase moisture absorption by at least 4 times, and reduce the TSP concentration by at least 81.4%. [ABSTRACT FROM AUTHOR]

The mineralogical composition of airborne dust particles is an important but often neglected parameter for several physiochemical processes, such as atmospheric radiative transfer and ocean biochemistry. We present the development of the METAL-WRF module for the simulation of the composition of desert dust minerals in atmospheric aerosols. The new development is based on the GOCART-AFWA dust module of WRF-Chem. A new wet deposition scheme has been implemented in the dust module alongside the existing dry deposition scheme. The new model includes separate prognostic fields for nine (9) minerals: illite, kaolinite, smectite, calcite, quartz, feldspar, hematite, gypsum, and phosphorus, derived from the GMINER30 database and also iron derived from the FERRUM30 database. Two regional model sensitivity studies are presented for dust events that occurred in August and December 2017, which include a comparison of the model versus elemental dust composition measurements performed in the North Atlantic (at Izaña Observatory, Tenerife Island) and in the eastern Mediterranean (at Agia Marina Xyliatos station, Cyprus Island). The results indicate the important role of dust minerals, as dominant aerosols, for the greater region of North Africa, South Europe, the North Atlantic, and the Middle East, including the dry and wet depositions away from desert sources. Overall, METAL-WRF was found to be capable of reproducing the relative abundances of the different dust minerals in the atmosphere. In particular, the concentration of iron (Fe), which is an important element for ocean biochemistry and solar absorption, was modeled in good agreement with the corresponding measurements at Izaña Observatory (22% overestimation) and at Agia Marina Xyliatos site (4% overestimation). Further model developments, including the implementation of newer surface mineralogical datasets, e.g., from the NASA-EMIT satellite mission, can be implemented in the model to improve its accuracy. [ABSTRACT FROM AUTHOR]

In this paper, atmospheric water-soluble cation and anion contents of PM10 are analysed in Makkah, Saudi Arabia. PM10 samples were collected at five sites for a whole year. PM10 concentrations (µg/m3) ranged from 82.11 to 739.61 at Aziziyah, 65.37 to 421.71 at Sanaiyah, 25.20 to 466.60 at Misfalah, 52.56 to 507.23 at Abdeyah, and 40.91 to 471.99 at Askan. Both daily and annual averaged PM10 concentrations exceeded WHO and Saudi Arabia national air quality limits. Daily averaged PM10 concentration exceeded the national air quality limits of 340 µg/m3, 32% of the time at Aziziyah, 8% of the time at Sanaiyah, and 6% of the time at the other three sites. On average, the cations and anions made a 37.81% contribution to the PM10 concentrations. SO42−, NO3−, Ca2+, Na+, and Cl− contributed 50.25%, 16.43%, 12.11%, 11.12%, and 8.70% to the total ion concentrations, respectively. The minor ions (F−, Br−, Mg2+, NO2−, and PO43−) contributed just over 1% to the ion mass. Four principal components explained 89% variations in PM10 concentrations. Four major emission sources were identified: (a) Road traffic, including emission from the exhaust, wear-and-tear, and the resuspension of dust particles (F−, SO42−, NO3−, Ca2+, Na+, Mg+, Br−, Cl−, NO2−, PO43−); (b) Mineral dust (Cl−, F−, Na+, Ca2+, Mg2+, PO43−); (c) Industries and construction–demolition work (F−, SO42−, Ca2+, Mg2+); and (d) Seaspray and marine aerosols (Cl−, Br−, Mg2+, Na+). Future work would include an analysis of the metal contents of PM10 and their spatiotemporal variability in Makkah. [ABSTRACT FROM AUTHOR]

Atmospheric aerosols have important effects on the environment and human health. In this study, we analyzed the atmospheric aerosol layers' optical and physical properties over Africa utilizing CALIPSO level 2 products from 2007 to 2019. Interannual and seasonal variations in aerosol optical parameters were studied: the lowest aerosol layer (AODL), the base height of the lowest aerosol layer (BL), the top height of the lowest aerosol layer (HL), the top height of the highest aerosol layer (HH), the volumetric depolarization ratio of the lowest aerosol layer (DRL), the color ratio of the lowest aerosol layer (CRL), the total AOD of all aerosol layers (AODT), the number of aerosol feature layers (N), the thickness of the lowest aerosol layer (TL), and the AOD proportion of the lowest aerosol layer (PAODL). The annual mean AODT was slightly higher in southern Africa than in northern Africa. HL and HH had strongly positive correlations with landform elevations. However, HL and HH were greater in northern Africa than in southern Africa from March to August. The reason could be that northern Africa is dominated by deserts with high temperatures and intense atmospheric vertical convections leading to dust layers existing in the upper air. PAODL values were lower in northern Africa (daytime: 71%; nighttime: 61%) than in southern Africa (daytime: 78%; nighttime: 69%), revealing that aerosol stratifications were more frequent in northern Africa than in southern Africa. DRL values were higher in northern Africa (daytime: 0.16; nighttime: 0.11) than in southern Africa (daytime: 0.07; nighttime: 0.05) indicating the predominance of non-spherical dust particles in northern Africa. This work can provide an important understanding of regional aerosol layers' optical and physical properties to scientists and local environmental protection agencies. [ABSTRACT FROM AUTHOR]

Asian dust (AD) events and total suspended particles (TSPs) were observed at the Kanazawa University Wajima Air Monitoring Station (KUWAMS), a Japanese background site, during the East Asian winter monsoon periods (from November to May of the following year) from 2010 to 2021. Nine kinds of polycyclic aromatic hydrocarbons (PAHs) were determined in each TSP sample. In this study, a total of 54 AD events were observed. According to the different pathways of long-range transportation, AD events were divided into AD-high events (transported at higher altitudes, approximately 4000 m) and AD-low events (transported at lower altitudes, approximately 2500 m). The TSP concentrations increased sharply in the AD events and were higher in the AD-high events (39.8 ± 19.5 μg/m3) than in the AD-low events (23.5 ± 10.5 μg/m3). AD did not have a significant effect on the ΣPAHs characteristic variation, as ΣPAHs (ΣPAHs = fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, benzo[ghi]perylene, and indeno [1,2,3-cd]pyrene) concentrations in non-AD periods, AD-high events, and AD-low events were 543 ± 374, 404 ± 221, and 436 ± 265 pg/m3, respectively. The PAH compositions were also consistent. As a result, the TSP concentration was affected by the input air mass transported at higher altitudes from the desert region while the PAH concentration was impacted by the air mass at lower altitudes, which carried the PAHs emitted from fossil fuels and biomass combustion in northeastern China. Moreover, the health risks of PAHs were calculated with the inhalation lifetime cancer risk, which ranged from 10−6 to 10−5 ng/m3, indicating a potential carcinogenic risk at the KUWAMS during the East Asian winter monsoon periods. [ABSTRACT FROM AUTHOR]

Air pollution in the Metropolitan Area of São Paulo (MASP), Brazil, is a serious problem and is strongly affected by local sources. However, atmosphere column composition in MASP is also affected by biomass burning aerosol (BB). Understanding the impacts of aerosol particles, from both vehicles and BB, on the air quality and climate depends on in-depth research with knowledge of some parameters such as the optical properties of particles and their chemical composition. This study characterized fine particulate matter (PM2.5) from July 2019 to August 2020 in the eastern part of the MASP, relating the chemical composition data obtained at the surface and columnar optical parameters, such as aerosol optical depth (AOD), Ångström Exponent (AE), and single-scattering albedo (SSA). According to the analyzed data, the mean PM2.5 concentration was 18.0 ± 12.5 µg/m3; however, daily events exceeded 75 times the air quality standard of the World Health Organization (15 µg/m3). The mean black carbon concentration was 1.8 ± 1.5 µg/m3 in the sampling period. Positive matrix factorization (PMF) identified four main sources of aerosol: heavy vehicles (42%), followed by soil dust plus local sources (38.7%), light vehicles (9.9%), and local sources (8.6%). AOD and AE presented the highest values in the dry period, during which biomass burning events are more frequent, suggesting smaller particles in the atmosphere. SSA values at 440 nm were between 0.86 and 0.94, with lower values in the winter months, indicating the presence of more absorbing aerosol. [ABSTRACT FROM AUTHOR]

The physical mechanisms associated with heat waves (HWs) are well known in the midlatitudes but still under-documented in the Sahel. Specifically, the role of anthropogenic and natural changes in tropospheric aerosols regarding HWs remains an issue to address. Our study focuses on the characterisation of the dusty HWs in the Sahel, which generally occur from March to June. The goal is to reinforce or invalidate the assumption proposed in previous studies recently carried out in southern Europe and according to which mineral dust may locally change irradiance at the surface, thus atmospheric temperatures at 2 m, intensifying the HW. The work is carried out in three steps: (i) detect and describe the HW over the 2003–2014 period based on maximum daily 2-m temperatures (T m a x ) from ERA-Interim reanalyses; (ii) characterise the dust optical properties during the HW using the Deep Blue aerosols products from MODIS (Moderate Resolution Imaging Spectroradiometre): the Aerosol Optical Depth at 550 nm (AOD 550 ), the Angstrom Exponent (AE 440 − 870 ) and the Single Scattering Albedo at 412 nm (SSA 412 ) as a proxy of quantity over atmospheric column, size and absorption of aerosols, respectively; (iii) relate HW intensity to the aerosol conditions during the HW. Over the 12-year study period, 14 HWs are detected when T m a x exceeds the 90th percentile (P90). The HWs are dusty with AOD 550 ranging between 0.46 and 1.17 and all the dust types are absorbent with a SSA 412 value of 0.93 (round to hundredths). The HW classification according to aerosol conditions gave three HWs: Type 1 corresponds to Pure Dust Situation (PDS with AE 440 − 870 = 0.1), Type 2 and Type 3 are associated with Mixed Situation (MS) with dominance of Coarse Particles (CP with AE 440 − 870 = 0.35) and Fine Particles (FP with AE 440 − 870 = 0.65), respectively. The main result obtained is that the intensity of the dusty HW, computed as the difference between daily T m a x and its P90 (T m a x −P90)), is higher for Type 1 HW (+1.1 °C) in the case of the most absorbent aerosol situation (SSA 412 = 0.931). A non-significant difference between Type 2 and Type 3 especially for temperature (+0.5 °C and +0.4 °C, respectively) and SSA (0.938 and 0.935, respectively) is observed and, during these mixing situations, the HWs are less intense than those during the PDS. Finally, the analysis of two huge Type 1 HWs in 2007 and 2010 shows that dust mass concentrations at the surface were particularly high, up to 214 μg/m3 on average. These findings enable us to assess that highly absorbent and concentrated pure dust situations observed in spring in the Sahel may have a potential warming effect at the surface. [ABSTRACT FROM AUTHOR]

This study investigated the sensitivity of the positive matrix factorization (PMF) model using concentrations of PM2.5-bound elements in Windsor, Ontario, Canada. Five scenarios were devised to assess impacts of input data on source identification, source contributions, and model performance. The study found that the model outcomes and performance were not sensitive to data below method detection limits (MDLs) being replaced with ½ MDLs, nor whether brown carbons (BrCs) data were excluded. By analyzing two episodic events individually, unique factors of fireworks and mineral dust were identified for each of the two episodes. Moreover, PMF model performance was improved greatly for event markers of the episodes and elements with less variability in concentration when compared with the base case scenario. Excluding the two episodes from the entire dataset had little impact on factor identification and source contributions but improved the model performance for three out of twelve elements unique to the two episodes. Overall, the PMF model outcomes and performance were sensitive to percentages of concentrations below MDLs and element concentrations with large variability due to high concentrations observed in episodes. Our findings are useful for dealing with data below MDLs and episodic events in conducting future PMF source apportionment of PM2.5-bound elements. [ABSTRACT FROM AUTHOR]

This study investigates the applicability of using the sky information from an all-sky imager (ASI) to retrieve aerosol optical properties and type. Sky information from the ASI, in terms of Red-Green-Blue (RGB) channels and sun saturation area, are imported into a supervised machine learning algorithm for estimating five different aerosol optical properties related to aerosol burden (aerosol optical depth, AOD at 440, 500 and 675 nm) and size (Ångström Exponent at 440–675 nm, and Fine Mode Fraction at 500 nm). The retrieved aerosol optical properties are compared against reference measurements from the AERONET station, showing adequate agreement (R: 0.89–0.95). The AOD errors increased for higher AOD values, whereas for AE and FMF, the biases increased for coarse particles. Regarding aerosol type classification, the retrieved properties can capture 77.5% of the total aerosol type cases, with excellent results for dust identification (>95% of the cases). The results of this work promote ASI as a valuable tool for aerosol optical properties and type retrieval. [ABSTRACT FROM AUTHOR]

Dust levels around the Tema industrial area of the Greater Accra Region have seen no reduction in recent years. Even though at some periods in time a natural drop in dust pollution levels is assured, the overall variation characteristics of the concentration of PM2.5, PM10, and Total Suspended Particles (TSP) have not been studied in recent years. This paper examines the levels of dust pollution across four (4) locations within the Tema metropolitan area with a specific interest in selecting locations and periods (weeks) significantly affected by dust pollution within the study area. Data collection was done over a nine-month period using the Casella 712 Microdust Pro Kit equipment. Measurements were done day and night at sampling points about 100 m apart in a given location. Monitoring was conducted once a week during the day and at night with a sampling period of 24 h per location, for thirty-six weeks. The generalized linear models were explored in selecting locations and weeks significantly affected by dust pollution. The study results showed no significant difference between pollution levels across the four selected locations. Eight, eleven, and five weeks out of the 36 weeks recorded significantly high concentrations of PM2.5, PM10, and TSP respectively. In addition, two out of the selected four areas (the oil jetty area and the VALCO hospital area) were found to have significantly high concentrations of dust pollution. The study recommends that an urgent air quality control policy intervention be put in place to control the highly alarming levels of dust pollution concentrations to guarantee and protect human health within the study area and beyond. [ABSTRACT FROM AUTHOR]

The re-deposition of detached dust during online pulse-jet cleaning is an important issue encountered during filter regeneration. To reduce dust re-deposition, multi-pulsing jet cleaning schemes were designed and experimentally tested. A pilot-scale pulse-jet cleaning dust collector was built with one vertically installed pleated filter cartridge. The effects of pulse duration and interval on the pulse pressure were tested, and the dust re-deposition rate and mechanism were studied and analyzed. It was found that, for the single-pulsing jet, the pulse duration had a critical value of approximately 0.080 s in this test, above which the pulse pressure remained at approximately 0.75 kPa and did not increase further. For the multi-pulsing jet with a small pulse interval (less than approximately 0.10 s), the pulse flows superimposed and reached a higher pulse pressure with a slight inhibition of dust re-deposition. For the multi-pulsing jet with a long pulse interval (over 0.15 s), dust re-deposition was clearly inhibited. The re-deposition rate decreased from 63.8% in the single-pulsing scheme to 24.4% in the multi (five)-pulsing scheme with the same total pulse duration of 0.400 s. The multi-pulsing scheme lengthens the duration of reverse pulse flow, resulting in more elapsed time for the detached dust to freely fall, and inhibiting the re-deposition of dust. The elapsed time in the five-pulsing jet scheme with the recommended pulse duration of 0.080 s and interval of 0.25 s was 2.8 times higher than that of the single-pulsing jet with the same total pulse duration. [ABSTRACT FROM AUTHOR]

Atmospheric aerosols have important impacts on global radiative forcing, air pollution, and human health. This study investigated the optical and physical properties of aerosol layers over Australia from 2007 to 2019 using the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) Level 2 aerosol products. Australia was divided into three sub-regions (western highlands, central plains, and eastern ranges). Interannual and seasonal optical property variations in aerosol layers in the three sub-regions were analyzed and compared. Results showed that annual mean values of AODL (lowest aerosol layer AOD) and AODT (total AOD of all aerosol layers) were always higher in the eastern ranges region than the other two regions from 2007 to 2019. The reason could be that Australian population was predominantly located in the eastern ranges region, where more human activities could bring significant aerosol loadings. BL (base height of the lowest aerosol layer), HL (top height of the lowest aerosol layer), and HH (top height of the highest aerosol layer) all showed trends of "western highlands > eastern mountains > central plains", indicating that the higher the elevation, the higher the BL, HL, and HH. TL (thickness of the lowest aerosol layer) was higher during the day than at night, which might account for increased diurnal atmospheric convection and nocturnal aerosol deposition. DRL (depolarization ratio of the lowest aerosol layer) was higher in the western highlands and central plains than the eastern mountains, probably because these two regions have large deserts with more irregularly shaped dust aerosols. CRL (color ratio of the lowest aerosol layer) had slightly higher values in the eastern ranges than the other two regions, probably due to the wet climate of the eastern ranges, where aerosols were more hygroscopic and had larger particle sizes. This study can provide technical support for the control and management of regional air pollutants. [ABSTRACT FROM AUTHOR]

Extreme meteorological events can influence air quality. In March 2021, northern China experienced a severe dust event, leading to widespread air quality deterioration. Using reanalysis datasets and station data, we investigate the synoptic weather patterns, dust transport characteristics, and associated impacts on air quality during this event. The results are as follows. (1) The dust event is closely linked to the Mongolian cyclone, providing favorable conditions for dust emission and long-distance transport. (2) The Gobi Desert in Mongolia is the primary source, with dust particles transported from Mongolia to northern China via the northwesterly flow. Dust transport exhibits a complex three-dimensional structure, with the most intense dust transport at approximately 2500 m altitude. (3) The impact of this dust event on air quality was characterized by its remarkable intensity, extensive spatial coverage, and prolonged duration. Additionally, 58.8% of the stations in northern China experienced pollution, 36.3% of them reached severe pollution levels or higher, and 35.9% of the sites experienced more than 12 h of pollution. (4) The visibility at the northern stations near the dust source rapidly decreases due to solid dust particles. In contrast, the southern stations, with higher moisture content, are primarily affected by liquid particles in terms of visibility. After the frontal passage, wet deposition from the precipitation process gradually improves visibility. [ABSTRACT FROM AUTHOR]

The various industries, sectors, and citizens' daily lives have undergone significant changes after the outbreak of the COVID-19 pandemic. The researchers collected and analyzed PM2.5 samples including secondary inorganic ions (SO42−, NO3−, and NH4+, namely SNA), organic carbon (OC), elemental carbon (EC), and other 16 metal elements in Beijing in 2019 (before the pandemic) and 2020 (after the pandemic). The particulate matter (PM2.5) concentration in the autumn and winter of 2020 is 21.16 µg/m3 and 14.05 µg/m3 lower than in 2019, respectively. The contribution of six sources of pollution, including coal combustion, secondary sources, transportation-related sources, dust, Industrial I, and Industrial II, were analyzed using the Positive Matrix Factorization (PMF) model. Due to the impacts of the COVID-19 pandemic, more and more people are choosing private transportation, such as private cars, instead of public transportation. As a result, the contribution of PM2.5 pollution related to transportation increased after the pandemic. The metal elements measured during the sampling period represent only a very small fraction (1%) of PM2.5. However, their health risk to humans cannot be ignored because of the toxicity of some metallic elements, and the carcinogenic risks induced by metal elements in PM2.5 exceeded the safety threshold (>10−6) during the autumn and winter of 2019 and 2020. Arsenic (As) contributes the most to carcinogenic risk, so controlling arsenic emissions is the primary approach to reducing cancer risk in Beijing. Considering the contribution to the health risk from various sources obtained in PMF, coal combustion is the most significant contributor to cancer risk. Therefore, serious consideration should be given to controlling coal combustion at the local and regional levels to reduce health risks in Beijing. [ABSTRACT FROM AUTHOR]

This study presents the source apportionment of coarse-mode particulate matter (PM10) extracted by 3 receptor models (PCA/APCS, UNMIX, and PMF) at semi-urban sites of the Indian Himalayan region (IHR) during August 2018–December 2019. In this study, water-soluble inorganic ionic species (WSIIS), water-soluble organic carbon (WSOC), carbon fractions (organic carbon (OC) and elemental carbon (EC)), and trace elements of PM10 were analyzed over the IHR. Nainital (62 ± 39 µg m−3) had the highest annual average mass concentration of PM10 (average ± standard deviation at 1 σ), followed by Mohal Kullu (58 ± 32 µg m−3) and Darjeeling (54 ± 18 µg m−3). The annual total ∑WSIIS concentration order was as follows: Darjeeling (14.02 ± 10.01 µg m−3) > Mohal-Kullu (13.75 ± 10.21 µg m−3) > Nainital (10.20 ± 6.30 µg m−3), contributing to 15–30% of the PM10 mass. The dominant secondary ions (NH4+, SO42−, and NO3−) suggest that the study sites were strongly influenced by anthropogenic sources from regional and long-range transport. Principal component analysis (PCA) with an absolute principal component score (APCS), UNMIX, and Positive Matrix Factorization (PMF) were used for source identification of PM10 at the study sites of the IHR. All three models showed relatively similar results of source profiles for all study sites except their source number and percentage contribution. Overall, soil dust (SD), secondary aerosols (SAs), combustion (biomass burning (BB) + fossil fuel combustion (FFC): BB+FFC), and vehicular emissions (VEs) are the major sources of PM10 identified by these models at all study sites. Air mass backward trajectories illustrated that PM10, mainly attributed to dust-related aerosols, was transported from the Thar Desert, Indo-Gangetic Plain (IGP), and northwestern region of India (i.e., Punjab and Haryana) and Afghanistan to the IHR. Transported agricultural or residual burning plumes from the IGP and nearby areas significantly contribute to the concentration of carbonaceous aerosols (CAs) at study sites. [ABSTRACT FROM AUTHOR]

In addition to human health, there are typical pollutants that significantly determine the quality of life and deteriorate the quality of the air. Although these pollutants are familiar in outdoor environments, they also pose a health threat in indoor environments. These need to be monitored and controlled. Children, who spend most of their time in these environments, are especially exposed to these pollutants, and such contaminants pose a threat during their learning and growing periods. In this study, the detection of heavy metals in indoor dust in educational institutions and their health risks were evaluated. Heavy metals such as arsenic, lead, mercury, and cadmium, which are named differently due to their densities, were detected, and their effects on children were determined. The measured values of heavy metals cadmium and arsenic were above the standard values of OSHA (Occupational Health and Safety Administration), one of the health and safety organizations. However, when educational institutions were examined, an increase in the amount of arsenic due to drinking water used, cadmium batteries containing batteries, the use of batteries, and the pigment feature in oil paint derivatives supplied with cadmium may increase the values. The other heavy metals such as Al, Zn, Hg, and Pb remained below the limit values. A health risk assessment was made by considering the data obtained from the samples taken from the educational institutions in Konya province, as well as factors such as environmental conditions, the number of students, the area per capita, temperature, and humidity. The causes of polluting sources and the precautions to be taken have been determined. [ABSTRACT FROM AUTHOR]

Over the last decades, the impact of mineral dust from African deserts on human health and climate has been of great interest to the scientific community. In this paper, the climatological analysis of dusty events of the past 20 years in the Caribbean area has been performed using a particulate approach. The focus is made on June 2020 extreme event dubbed "Godzilla". To carry out this study, different types of data were used (ground-based, satellites, model, and soundings) on several sites in the Caribbean islands. First, the magnitude of June 2020 event was clearly highlighted using satellite imagery. During the peak of this event, the value of particulate matter with an aerodynamic diameter of less than 10 μ m ( P M 10 ) reached a value 9 times greater than the threshold recommended by the World Health Organization in one day. Thereafter, the P M 10 , the aerosol optical depth, and the volume particle size distribution analyses exhibited their maximum values for June 2020. We also highlighted the exceptional characteristics of the Saharan air layer in terms of thickness and wind speed for this period. Finally, our results showed that the more the proportion of particulate matter with an aerodynamic diameter of less than 2.5 μ m ( P M 2.5 ) in P M 10 increases, the more the influence of sea salt aerosols is significant. [ABSTRACT FROM AUTHOR]

The results of a preliminary investigation of the dust sources in the Arctic based on their geochemical properties by potential source contribution function (PSCF) analysis are presented in this paper. For this purpose, we considered one year of aerosol geochemical data from Ny-Ålesund, Svalbard, and a short list of chemical elements (i.e., Al, Fe, Mn, Ti, Cr, V, Ni, Cu, and Zn) variably related to the dust fraction. Based on PSCF analysis: (i) four different dust source areas (i.e., Eurasia, Greenland, Arctic-Alaska, and Iceland) were characterized by distinguishing geochemical ranges and seasonal occurrence; and (ii) a series of typical dust days from the distinct source areas were identified based on the corresponding back trajectory patterns. Icelandic dust samples revealed peculiar but very variable characteristics in relation to their geographical source regions marked by air mass back trajectories. The comparison between pure and mixed Icelandic dust samples (i.e., aerosols containing Icelandic dust along with natural and/or anthropogenic components) revealed the occurrence of different mixing situations. Comparison with Icelandic soils proved the existence of dilution effects related to the emission and the transport processes. [ABSTRACT FROM AUTHOR]

A prominent Saharan Air Layer (SAL) was detected over the Northern Atlantic from the West African Coast to the Caribbean Sea in 2007. Data was collected from the Aerosols and Ocean Science Expedition (AEROSE), which encountered a major dust outflow on 13 and 14 May 2007. These observational measurements came from onboard instrumentation and radiosondes that captured the dust-front event from 13 to 14 May 2007. Aerosol backscatter was confined within the Marine Boundary Layer (MBL), with layers detected up to 3 km. Aerosol Optical Depth (AOD) increased by one order of magnitude during the dust front, from 0.1 to 1. Downward solar radiation was also attenuated by 200 W/m2 and 100 W/m2 on the first and second days, respectively. A weaker gradient at and above 500 m from potential temperature profiles indicates a less-defined MBL, and an ambient air temperature of 26 °C on 14 May and 28 °C on 15 May were observed above 500 m, reinforcing the temperature inversion and static stability of the SAL. Subsequent days, clear and boundary-layer cloudy days were observed after the dust front. From 14 to 18 May, a Convective Inhibition (CIN) layer started to form at the top of the MBL, developing into a negative buoyancy from 17 to 23 May, and reinforcing the large-scale anticyclonic atmospheric conditions. These results show that the SAL acts as positive feedback on suppressing deep convection over the tropical Atlantic during this dust outflow and several days after its passage. [ABSTRACT FROM AUTHOR]

Following population growth and rapid urbanization, West African cities have become major sources of anthropogenic pollution. Additionally, Saharan dust has had a significant impact, representing a potentially toxic mix of sources for the population. This study characterizes the atmospheric composition and its sources in two African capitals, Bamako, Mali and Dakar, Senegal. TSP, PM10 and PM2.5 samples were collected during the dry season in 2009 when pollution levels were high: chemical analysis included organic carbon (OC), elemental carbon (EC), ions, and metals. PM2.5 and PM10 concentrations were 5–10 times and 3–8 times higher, respectively, than the 2005 WHO 24 h standards. Using PCA and PMF methodologies, five sources were identified in each city. In Bamako, traffic (motor vehicles and resuspended road dust) was the prevailing source of PM2.5 and PM10, accounting for 47% and 45%, respectively. Crustal dust was the second most important source (24–30%), followed by solid fuel combustion (16–13%) and secondary aerosols (10–16%). In Dakar, the following sources of PM2.5 and PM10 are identified: traffic (49%), mineral dust (16–25%), sea salts (15–20%) and industries (10–11%). Our study provides crucial information about the historical change in source characteristics in these two African cities, which can help for future mitigation strategies. [ABSTRACT FROM AUTHOR]

We explored spectral diversity in infrared (IR, 4–25 μm) imaginary (k) and real (n) indices of refraction (optical constants) for 26 surface soils that originated from global dust entrainment regions. The k spectra were derived from optical transmission spectra of KBr pellets containing dispersed dust and the n spectra were estimated with the subtractive Kramers–Kronig (SKK) method. We compared k and n obtained by this study with previously published values. Our optical constants from the KBr technique are comparable in magnitude and spectral shape to those from previous studies that used dust aerosols re-suspended in a chamber. This suggests that the SKK method can offer a reliable mechanism for measuring IR spectra of both optical constants for soils. The soils used here exhibit additional spectral variability compared with past studies. We note that the appearance and the shift in positions of the strongest absorption peaks are due to combinations of silicates with overlapping absorption, rather than being related to a single mineral. We note that all dust optical constants have substantially lower magnitudes compared to those of pure minerals. Our results can improve estimates of mineral dust radiative effects and support quantification of surface mineral estimates using satellite and ground-based remote sensing. [ABSTRACT FROM AUTHOR]

Intense cutting-induced dust production in fully mechanized mining faces (FMMFs) with large mining heights produces a high amount of dust that is difficult to capture and severely affects the working environment, threatening the health of occupational staff. The effective spray range and atomization performance of tracking sprays are counteracted by the influences of the mine's height and ventilation airflow in FMMFs. Thus, optimizing the spray's parameters and relationship between the effective spray range and atomization performance to reduce dust levels is the main priority of dust-control techniques. In this study, a new swirl-core atomization nozzle is developed based on fluid mechanics and the solid–liquid coalescence mechanism. The liquid generates a circumferential velocity when passing through the swirl core, which considerably increases the droplet breaking power and reduces the droplet cohesion factor, achieving a remarkable atomization effect. The spray angle of the new nozzle is 57°, which is 80.9% greater than the GZPW-16 mine-use nozzle (31.5°); the effective spray range increases from 5.2 to 5.9 m; and the spray's mist saturation is significantly better than the GZPW-16 mine-use nozzle. Under different test pressures, the particle size range of the droplets produced by the new nozzle and dust particles on site satisfied the best synergy of droplet–dust coalescence. The total and respirable dust-reduction rates were 78% and 75.1%, respectively, which were 42% and 65% higher than those of the original nozzle. The new nozzle effectively improves the efficiency of the single dust-control technique of the tracking spray, which is significant for the dust-prevention and -control technology of FMMFs with large mining heights. [ABSTRACT FROM AUTHOR]

Six phthalates: dimethyl phthalate (DMP), diethyl phthalate (DEP), di(n-butyl) phthalate (DnBP), butyl benzyl phthalate (BBzP), di(2-ethylhexyl) phthalate (DEHP), and di(n-octyl) phthalate (DOP) in settled dust on different indoor surfaces were measured in 30 university dormitories. A Monte Carlo simulation was used to estimate college students' exposure via inhalation, non-dietary ingestion, and dermal absorption based on measured concentrations. The detection frequencies for targeted phthalates were more than 80% except for DEP (roughly 70%). DEHP was the most prevalent compound in the dust samples, followed by DnBP, DOP, and BBzP. Statistical analysis suggested that phthalate levels were higher in bedside dust than that collected from table surfaces, indicating a nonuniform distribution of dust-phase phthalates in the sleep environment. The simulation showed that the median DMP daily intake was 0.81 μg/kg/day, which was the greatest of the targeted phthalates. For the total exposures to all phthalates, the mean contribution of exposures during the daytime and sleeping time was 54% and 46%, respectively. [ABSTRACT FROM AUTHOR]

For the pollution assessment and quantitative source apportionment of heavy metals in surface dust, a total of 52 surface dust samples were collected from bus stops in Tianshui City. The geoaccumulation index (Igeo) and potential ecological risk index (RI) were used to analyze the pollution levels caused by heavy metals. The Positive Matrix Factorization (PMF) of the receptor modeling and geo-statistics were employed to analyze the source of the heavy metals. The results were as follows. ① Except for Mn, Co and V, the mean concentrations of other heavy metals have exceeded the local background value of Gansu. The percentage of excessive concentrations of Cu, Zn, Sr, Ba and Pb in the samples was 100%, and that of Cr, Ni and As were 96.15%, 94.23%, and 96.15%, respectively. ② Semivariogram model fitting showed that the block-based coefficients of Cu, Zn, Sr, Ba, Pb, Cr, Ni, and As were between 0.25 and 0.75, indicating that they were mainly affected by human factors. The high values of Pb, Zn, Ni and As were mainly distributed in the eastern part of the study area, and the high values of Cu, Sr, Ba and Cr were distributed in a spot-like pattern in the study area. ③ The Igeo results showed that As, Cu, Zn, and Pb were the main contamination factors, and the optimized RI showed that the heavy metals were the overall ecological risk of intensity, among which Pb, As and Cu were the main ecological factors and should be taken as the priority control objects. ④ Based on the PMF, there are four main sources of eleven heavy metals. V, Mn, and Co were attributed to natural sources, accounting for 18.33%; Cu, Sr, and Ba were from mixed sources of pollution from transportation and industrial alloy manufacturing, accounting for 26.99%; Cr and Ni were from sources of construction waste pollution, accounting for 17.17%, As, Zn and Pb were mainly produced by coal-traffic mixed pollution emissions, accounting for 37.52%. Overall, the study area was dominated by coal-traffic emissions. [ABSTRACT FROM AUTHOR]