Search

Anteroposterior (AP) whole leg radiographs (WLR) in the standing position for assessment of the mechanical leg axis are generally performed preoperatively for the planning of total knee replacement (TKR) and postoperatively to assess the leg axis. The objective of the present study was to investigate whether, if preoperative WLR are available, postoperative AP standard knee radiographs in the standing position are sufficient for calculating the mechanical leg axis. In the present prospective study, the mechanical and the anatomical leg axes were determined on the basis of WLR from 104 patients prior to implantation of a TKR and the difference was calculated. Twelve weeks postoperatively, standing long AP radiographs and WLR were prepared. In addition, the mechanical axis was calculated by adding the preoperative difference between the anatomical and mechanical axis to the anatomical axis from the postoperative AP radiographs. Accuracy, bias and level of agreement for calculated relative to measured mechanical alignment were determined. Mean accuracy of calculated mechanical alignment was 0.5° ± 0.4°, and mean bias was 0.0° ± 0.6° (p = 1.00). Bland–Altman analysis revealed a 95% upper and lower level of agreement of − 1.3° and 1.3°, respectively. A preoperative WLR and a postoperative long AP knee standard radiograph are sufficient to determine the mechanical leg axis after TKR. If these are available, it is possible to do without WLR after TKR, particularly since they involve higher radiation exposure, are time-consuming, and are also prone to errors in the first postoperative weeks. II diagnostic study.

Individual implant alignment in total knee arthroplasty (TKA) has seen growing interest over the past years. This study therefore aimed to develop a surgical technique for implant alignment based on native ligament tension, and to present the results obtained using this technique. 25 patients were included in this prospective study. Patient-specific instrumentation (PSI) was used for the resection of the extension gap. Ligament tension was measured after the removal of all accessible osteophytes. In the event of asymmetry, the distal femur resection was adjusted up to 2.5° using an adjustable cutting block. The aim was to achieve a symmetrical extension gap without release, not a neutral leg axis. Femoral rotation was aligned on the basis of ligament tension. Patients were followed up to 3 months postoperatively. The postoperative whole-leg axis was 2.8° ± 1.6° varus. Patients achieved a flexion of 118° ± 9°, a Knee Score of 91.5 ± 3.2 and a Function Score of 86.8 ± 8.3 points. Conclusion: For the first time, the new surgical technique described here permits a ligament tension based femoral implant alignment together with PSI. It was shown to be safe, with encouraging clinical and radiological results. Level of Evidence: Therapeutic study level IV

Combining patient-specific instrumentation (PSI) with a balancer device in total knee arthroplasty (TKA) to achieve functional femoral rotational alignment is a novel technique. The primary goal of this study was to introduce a new method to combine PSI with a gap-balancing technique and to determine the impact of the technique on rotation of the femoral component. Twenty-five primary TKAs (15 women, 10 men) were prospectively studied. All TKAs involved PSI with an associated gap-balancing device. Front plane alignment was performed intraoperatively with the PSI, followed by rectangular, symmetrical extension and creation of a flexion gap using the balancer device to set the femoral rotation. Femoral component rotation was between 3° internal and 6° external rotation versus the transepicondylar axis. There were no postoperative signs of patellofemoral dysfunction. In no cases was the resulting joint line displacement >3 mm. The mean elevation was 1.2 ± 0.9 mm (range 0–3). The leg axis was straight in all cases (±3°), at a mean of 1.6° ± 1.0° varus (range 0°–3° varus). PSI was with the gap-balancing technique was successfully used without affecting anatomical alignment. With the balancer device, PSI can be used more widely than techniques based solely on landmarks, as the soft-tissue tension can be taken into account, thus virtually eliminating flexion instabilities.