Search

This project studies the influence of different grain sizes of Ni-based Fe-33Ni-19Cr alloy obtained from heat treatment procedure on high temperature isothermal oxidation. Heat treatment procedure was carried out at two different temperatures, namely 1000°C and 1200°C for 3 hours of soaking time, followed by quenching in the water. These samples are denoted as T1000 and T1200. The heat-treated Ni-based Fe-33Ni-19Cr alloy was subjected to an isothermal oxidation test at 950°C for 150 hours exposure. Oxidized heat-treated alloys were tested in terms of oxidation kinetics, phase analysis and surface morphology of oxidized samples. Oxidation kinetics were determine based on weight change per surface area as a function of exposure time. Phase analysis was determined using the x-ray diffraction (XRD) technique and surface morphology of oxidized samples was characterized using a scanning electron microscope (SEM). As a result, the heat treatment procedure shows varying grain sizes. The higher the heat treatment temperature, shows an increase in grain size with a decrease in hardness value. The oxidation kinetics for both heat-treated samples showed an increment pattern of weight change and followed a parabolic rate law. The oxidized T1000 sample recorded the lowest parabolic rate constant of 3.12×10-8 mg2cm-4s-1, indicating a low oxidation rate, thus having good oxidation resistance. Phase analysis from the XRD technique recorded several oxide phases consisting of Cr2O3, MnCr2O4, and (Ti0.97Cr0.03)O2 oxide phases. In addition, a uniform oxide layer is formed on the oxidized T1000 sample, indicating good oxide scale adhesion, thereby improving the protective oxide behavior. [ABSTRACT FROM AUTHOR]

The article presents a precise method for the orientation process of NiMnGa-based single crystals. For this method, a scanning electron microscope equipped with an EBSD camera and a heating stage allowing temperatures exceeding 873 K was used. The orientation process was carried out in both the high-temperature austenite phase and in the room-temperature martensite phase. The facilities allowed for determining the orientation of a single grain of austenite at elevated temperatures as well as the orientation of particular martensitic variants at room temperature. A practically perfect cubic orientation was obtained in the austenitic case with a deviation of about 1° while the samples oriented in the martensitic phase deviated from the desired orientation by 4.5-5.2°. Additionally, the training process of single crystals was carried out in order to show the influence of the orientation process on twinning stress. [ABSTRACT FROM AUTHOR]

In this study, a molybdenum alloy with dispersed high-entropy particles was fabricated using the powder metallurgy method. The high-entropy powder, composed of Nb, Ta, V, W, and Zr elements with a same atomic fraction, was prepared via high-energy ball milling. Using this powder, an ideal core-shell powder, composed of high-entropy powder as core and Mo powder as shell, was synthesized via the milling and reduction processes. These processes enabled the realization of an ideal microstructure with the high-entropy phase uniformly dispersed in the Mo matrix. The sintered body was successfully fabricated via uniaxial compaction followed by pressureless sintering. The sintered body was analyzed by X-ray diffraction and scanning electron microscope, and the high-entropy phase is uniformly dispersed in the Mo matrix. [ABSTRACT FROM AUTHOR]

Evaluation of inorganic and organic compounds as corrosion inhibitors of Cu-Zn alloys in H2SO4 and HNO3 solutions was studied using potentiodynamic and impedance spectroscopy along with scanning electron microscope (SEM) and energy dispersive X-Ray analyzer (EDX) investigations. The corrosion inhibition of Cu-Zn alloys was investigated in oxy acid solutions using inorganic potassium permanganate and di-hydrogen phosphate, amino acids as environmentally safe materials, commercial cooling water, and green tea extracts. Both potassium permanganate and di-hydrogen phosphate improve the corrosion resistance of Cu-Zn alloys. Phosphate appears more effective as corrosion inhibitor for Cu-Zn alloys than permanganate. The inhibition efficiency (IE%) of the different amino acids such as valine, leucine and lysine was also calculated. The experimental results have shown that amino acid-like lysine can be used as an efficient corrosion inhibitor for the Cu-Zn alloys in oxy acid solutions. This may be due to the presence of two amino groups adsorbed together. For lysine, inhibition efficiency, IE%, of ~87 and ~59 is for H2SO4 and ~96.3 and 54.9 for HNO3 for alloy I and II respectively are observed. Due to the composition of green water have a great effect on the inhibition action on Cu-Zn alloys which reaching 91.8 and 96.5% for Alloy I and 95.4 and 87.1% for Alloy II in 0.5 M H2SO4 and HNO3 respectively. Although benzotriazole, in cooling water, is an excellent inhibitor suitable for use in a wide variety of environments, it has toxic properties. So, much of the recent researches have focused on formulating new and more environmentally acceptable preservation solutions. The green tea, as plant extract, will be very environmentally friendly. The EDX confirm the formation of a protective layer on the Cu-Zn alloys containing aluminum in Alloy II. This sequence reflects the beneficial effects of Al in Alloy II. The presence of 2.43% Al in Alloy II improves the corrosion resistance due to the formation of thin, transparent, stable and self - healing Al2O3 layer. This confirmed the results obtained from the potentiodynamic polarization measurements and EIS methods. [ABSTRACT FROM AUTHOR]

Mixture of nickel and titanium powders were milled in planetary mill under argon atmosphere for 100 hours at room temperature. Every 10 hours the structure, morphology and chemical composition was studied by X-ray diffraction method (XRD), scanning electron microscope (SEM) as well as electron transmission microscope (TEM). Analysis revealed that elongation of milling time caused alloying of the elements. After 100 hours of milling the powders was in nanocrystalline and an amorphous state. Also extending of milling time affected the crystal size and microstrains of the alloying elements as well as the newly formed alloy. Crystallization of amorphous alloys proceeds above 600°C. In consequence, the alloy (at room temperature) consisted of mixture of the B2 parent phase and a small amount of the B19' martensite. Dependently on the milling time and followed crystallization the NiTi alloy can be received in a form of the powder with average crystallite size from 1,5 up to 4 nm. [ABSTRACT FROM AUTHOR]

Pre-alloyed Astaloy CrLTM (Fe-1.5 wt% Cr-0.2 wt% Mo), a commercial Fe-based alloy powder for high strength powder metallurgy products, was sintered and hot forged with additions of 0.5 wt% C and 0~2 wt% Cu. To investigate the influence of various Cu contents, the microstructural evolution was characterized using density measurements, scanning electron microscope (SEM) and electron backscatter diffraction (EBSD). Transverse rupture strength (TRS) was measured for each composition and processing stage. The correlation between Cu additions and properties of sinter-forged Fe-Cr-Mo-C alloy was discussed in detail. [ABSTRACT FROM AUTHOR]