Search

The excellent performance of graphene nanoplatelets turns them into engaging fillers for different materials, offering a wide range of applications from energy harvesting, flexible electronic devices, smart sensors and structural-functional composites.

The present work studies the electrical and electrothermal properties of CNT/GNP-doped nanocomposites for optimizing their anti-icing and de-icing capabilities. Here, a comparison between 3D-printed circuits and coatings based on these materials is carried out. In this regard, the higher electrical conductivity that is achieved by the specimens when increasing the nanoparticle content and the higher cross-sectional area of the coatings with regard to the 3D-printed circuits induces a higher heat generated by the Joule’s effect. Moreover, the successful de-icing test performed by the specimen with the highest self-heating capability, evinces that the studied nanocomposites are suitable for de-icing purposes.

This work consists of the development of an easy strategy to transform any structure into an efficient surface heater by the application of a low voltage over 3D printed nanocomposite circuits. To this end, the electrical conductivity and self-heating capabilities of UV-Assisted Direct Write 3D printed circuits doped with carbon nanotubes were widely explored as a function of the number of printed layers. Moreover, an optimization of the printing process was carried out by comparing the accuracy and printability obtained when printing with two different configurations: extruding and curing the ink in the same stage or curing the extruded ink in a second stage, after the whole layer was deposited. In this regard, the great homogeneity and repeatability of the heating showed by the four-layer printed circuits, together with their excellent performance for long heating times, proved their applicability to convert any structure to a surface heater. Finally, the deicing capability of the four-layer circuit was demonstrated, being able to remove a 2.5 mm thick ice layer in 4 min and 4 s.

The use of graphene nanoplatelets for several purposes such as barrier properties and structural health monitoring is widely studied in polymer-based coating technology. Nevertheless, their extremely good effect on wear resistance makes them particularly interesting for coating technology. The effect of graphene nanoplatelets addition on the wear behaviour of an epoxy resin was analysed. The effects of graphene nanoplatelets content (0–8 wt.%), morphology and functionalization in wear behaviour were analysed by evaluating the main wear parameters of the nanocomposites studied. The morphology of the wear surfaces was analysed by scanning electron microscopy (SEM) and 3D optical profilometry in order to evaluate the mechanism and severity of wear. The results showed that the wear behaviour of the epoxy resin improved considerably with the addition of graphene, especially for higher contents. Moreover, as the wear mechanism depends on the morphology of graphene nanoplatelets, it was concluded that the proper selection of graphene can be made depending on the chosen application.

Carbon fiber-reinforced plastic bonded joints with novel carbon nanotube (CNT) adhesive films were manufactured and tested under different aging conditions by varying the surfactant content added to enhance CNT dispersion. Single lap shear (SLS) tests were conducted in their initial state and after 1 and 2 months immersed in distilled water at 60 °C. In addition, their electrical response was measured in terms of the electrical resistance change through thickness. The lap shear strength showed an initial decrease due to plasticization of weak hydrogen bonds, and then a partial recovery due to secondary crosslinking. This plasticization effect was confirmed by differential scanning calorimetry analysis with a decrease in the glass transition temperature. The electrical response varied with aging conditions, showing a higher plasticity region in the 1-month SLS joints, and a sharper increase in the case of the non-aged and 2-month-aged samples; these changes were more prevalent with increasing surfactant content. By adjusting the measured electrical data to simple theoretical calculations, it was possible to establish the first estimation of damage accumulation, which was higher in the case of non-aged and 2-month-aged samples, due to the presence of more prevalent brittle mechanisms for the CNT-doped joints.

In this study, the hydrothermal resistance of an epoxy resin (aircraft quality) reinforced with graphene is analyzed. Different geometries and aspect ratios (thickness and lateral dimensions) of graphene nanoplatelets were studied. The addition of these graphene nanoplatelets induces important advantages, such as an increase of the glass transition temperature and stiffness and an enhancement of barrier properties of the epoxy matrix, in spite of the excellent behavior of pristine resin. The effectiveness of graphene nanoplatelets increases with their specific surface area while their dispersion degree is suitable. Thinner nanoplatelets tend to wrinkle, decreasing their efficiency as nanofillers. Graphene used as reinforcement not only reduces the absorbed moisture content but also decreases its effect on the thermal and mechanical properties related to the matrix.