Search

Storage is an important aspect of any business. All businesses must store goods and materials safely, especially warehouses, factories, shops, food, agricultural, and construction businesses. Leaving materials exposed reduces their overall quality; hence, certain structures are used to safely retain the materials for further use. These are called storage structures. A silo is a commonly used storage structure for the storage of bulk materials such as grain and cement. This paper deals with the design of a steel silo for the storage of pozzolana cement. A storage silo is essentially made up of a cylinder-shaped wall and a hopper bottom. Steel Silos are gaining more popularity in terms of cement storage usage. A 150-ton capacity steel silo has been designed for a seismic zone-2 [1] location in Madurai, Tamil Nadu, India (therefore omitting the inclusion of seismic loads). The preliminary design of the silo structure is carried out with the help of Indian Standard code books. Indian Standard code books such as IS 9178-Parts 1,2 & 3 (1979) were used for the basic design. Other necessary code books were used for load calculations. The plan and elevation of the Silo have been drafted by using AutoCAD. The designed Silo is analysed using STAAD Pro. The pile foundation of the Steel Silo has also been designed and analysed using STAAD Foundation.

Currently, the manufacturing industries play an important part in the global economy. I t is critical for the industries to maintain the high standards of goods and products. Various machines / systems have been developed for determining dimensional stability or the lack of filling in a casting product, thereby rejecting the defective products. The existence of the casting product is detected using an infrared or ultrasonic sensor. When a product arrives along the conveyer, the sensor can detect its measurements. If the product has the necessary proportions and dimensions, it is moved to the accepted bin; otherwise, it is denied by a pneumatic actuator and placed in the rejecter bin. Eventually, a profound learning model that categorizes into two different categories has been studied to automate the manual inspection procedure in the casting failure system. This automated casting fault separation machine is accurate, reliable and low cost which makes it suitable for small scale industries with easy segregation of high quality products. The objective of this paper is to review the various automatic systems developed for separating casting fault.

In the current unstable economy, every fabricating sector has continuously made attempts to ensure its survival by adopting new and effective procedures to improve productivity. The industry's production issues were brought on by poor equipment handling, a lack of inventory classification, and an unorganized storage area. So, the objective is to reduce the waste, risk of labour, production cost, and time, and increase the workspace and production, thus gradually influencing the industry's overall profit. It can be achieved by implementing the most relevant lean techniques. Lean, an emerging technology, is used in manufacturing sectors to find and eliminate waste and increase efficiency. It is a completely customer-based strategy that concentrates on the value chain and its improvement. In this paper, lean analysis suggests using a 5S for restructuring the storage area, Kanban, and Kaizen for properly handling waste. It is observed that there is a significant improvement after this implementation.

This paper describes the results of a field investigation with the objective of evaluating the possibility to produce drone-derived 3D digital point clouds sufficiently dense and accurate to determine the rock mass rating (RMR) in the underground mine in Bukit Kachi. Agisoft Photoscan software was used for producing the three-dimensional points cloud from the two-dimensional images' sequences. The rock mass rating was evaluated by using Discontinuity Set Extractor (DSE) and Dips 7.0 in Rockscience software. Results from this research show that 3D digital point clouds, derived from the processing of drone-flight images, were successfully used for reliable representation of discontinuity of the tunnel. According to the results of the analysis, both Tunnel A and Tunnel B are classified as "fair rock." Meanwhile, Tunnel A is failing due to geological conditions of feldspar decomposition that are classified as class I, which is "very poor rock." According to Dips 7.0 analysis, the major direction of discontinuity set of Tunnel A for Window right is N300 – N310, while for Window left is N350 – N360. The most dominant discontinuity direction for Tunnel B Window right is N340 – N350, and the orientation for Window left is N10 – N20. When manual mapping and DSE analysis are compared, both orientations of the discontinuity do not give the same direction due to less data reading in the field and high accuracy from the software.

Cenospheres are valuable material contained inside the fly ash. Its low weight, low density, and high strength made it very versatile and can be used in various fields. The way of separating the cenosphere from the fly ash consists of two categories, wet and dry separation. For wet separation, it involves submerging the fly ash inside a mixture made either by pure acetone, pure water, or a mixture of water and acetone with different mixing ratios before stirring the mixture. The cenospheres, floating on top of the mix due to low density, can be collected and dried. The dry separation technique involves putting the fly ash into a cyclone separator at a constant velocity. The fly ash will then move into the bottom of the cyclone. Particles can also be separated by diameter sizes by sieving. By manipulating various parameters, cenosphere yield may differ. This paper is written to help gain more understanding on cenosphere properties and its separation method.

Water treatment sludge (WTS) is a by-product produced in the process of water treatment plants (WTP). It is estimated that an ordinary WTP produces over 10,000 tonnes of WTS per day, which has become a major concern in the management of WTS. Numerous previous studies have been accomplished to determine a safe disposal method and the potential reuse of WTS. In most investigations, material characterisation was the adopted method. It is known that each WTP produces different chemical composition of WTS according to raw water intake and the treatment process. The aim of this paper is to examine the chemical composition of WTS in the WTP at Melaka. The WTS sample is collected from WTP after the pressing process, where large amounts of water have been removed. The sample is tested using the Scanning Electron Microscopy with energy dispersive X-ray (SEM-EDX) and X-ray Diffraction (XRD). The SEM-EDX results revealed that by weight percentage (%), WTS contains zirconium (Zr) (28 to 46%), oxygen (28 to 40%) and carbon (7 to 26%). Aluminium and silicon have weight percentages ranging from 7 to 8%. The outcomes are then confirmed by XRD, which showed the high intensity of Zr and α-Zr at approximately 35.3 and 36.1. of 2θ. Based on these findings, the suitable and potential reuse of WTS would be the extraction of Zr. However, further research is required to verify the consistency of Zr in WTS.

The tremendous exhaustion of resources, a surprising price increase of petroleum fuel and worldwide ecological issues implement to find renewable fuel for compression ignition engine. Non-edible vegetable oils have proven consensus to opt as a replacement for diesel fuel due to comparable properties and less-pollutant characteristics. Using Unmixed Untreated Non-edible Vegetable Oil (UUNVO) in the CI engine matches the needs of a sustainable future and restricts the intensifying cost involved in biodiesel production. This paper aims to review the influence of various UUNVO (Karanja, Jatropha, Neem, Linseed, Mahua and Rubber Seed etc.) on the important performance parameters and emission level of diesel engine. UUNVO can be fuelled to the unmodified CI engine. However, the viscosity of UUNVO is reasonably higher compare to diesel fuel at room temperature, which deteriorates the engine performance and exhaust emission. Minor changes in the injection line for preheating the UUNVO and operating parameters are the way to improve it. It can clearly understand here that preheated UUNVOs typically increase NOx emissions and decrease PM, HC, and CO emissions level compared to standard diesel. UUNVO can substitute diesel fuel completely for short-duration operation. With the long-duration operation, UUNVO produces problems like poor engine performance, injector chocking, and erosion of piston crown, rings, cylinder liner, and other internal parts, and degradation of the lubricant. Problems raised due to durability can be minimized by controlling operational parameters.

Thermoelectric technology is one of the fast-developing technologies in the present days due to its excellent heat transfer and heat conversion capabalities. This uses the electromotive force produced by the temperature difference at each end of the device to produce electricity and vice versa. There are various applications developed based on this thermoelectric technology which includes thermoelectric coolers, thermoelectric generators, and thermoelectric air conditioners. This paper provides a comprehensive analysis of thermoelectric (TE) technologies, starting with a complete summary of their working principles explaining the effects like Seebeck, Peltier, and Thomson effects, as well as optimization techniques, applications, semi-conductor materials used, and potential future developments.

Robot grasping detection methods are categorized into two-dimension (2D) and three-dimension (3D) approaches. In 2D grasp detection, gripper pose prediction occurs directly on RedGreenBlue (RGB) images, limiting grasp direction. Conversely, 3D grasp detection predicts gripper pose using 3D point clouds, allowing greater grasp flexibility. However, the data volume of 3D point clouds hampers real-time detection. To address this, this paper proposes a novel grasping detection algorithm that combines 2D images and 3D point clouds. Initially, a Single Shot MultiBox Detector (SSD) network generates 2D prediction boxes on RGB images. Through enhancements to the prior box scaling, the accuracy of bounding the target object is improved. Subsequently, 2D boxes are transformed into 3D frustums, and extraneous data points are removed. By utilizing Random Sampling Consistent Segmentation (RANSAC) and Euclidean Clustering Segmentation Algorithm (ECSA), the target point clouds are isolated, and subsequently, the spatial pose of the target is represented using an Oriented Bounding Box (OBB). Processed point clouds enter an enhanced PointNet Grasp Pose Detection (PointNetGPD) algorithm, In contrast to the original approach involving extensive random sampling of grasp candidates, the enhanced PointNetGPD method enables the selective sampling of grasp candidates by incorporating pose constraints between the target and gripper. Following this, the generated grasp candidates are subjected to evaluation through a scoring process conducted by an assessment network. Ultimately, the robotic arm is guided to perform the grasp associated with the highest score. In the experimental phase, the proposed algorithm demonstrated a high success rate in capturing multiple targets, along with a reduced grasping time. These results underscore the algorithm's superior grasping quality and enhanced real-time performance when compared to similar algorithms.

Sustainability is one of the most challenging concepts in the global mining industry. The purpose of this is to limit the harmful effects of mineral extraction on the environment and at the same time to meet the present and future needs of civilization. Therefore, we should blaze the path leading to sustainability and supply security, as well as identify the factors affecting these concepts. Thus, in this paper, the main factors are listed and defined. They are divided into two main categories: the positives and the negatives. The positives are the longevity of the minerals' mining, the index of the annual met need, the environmental-social condition of the resources, and the condition of the resources in friend countries. Also, the negative ones are the harmful chemicals released, the energy required per ton of minerals, annual CO2 emitted per ton, and recyclability. Accordingly, the factors can be used to make a strategic plan for the future of the minerals supply of a country. So, the framework developed leads the authorities to find the solutions to the sustainability of minerals' supply and increase the security of mining productions.

Infectious disease such as COVID-19 is one of the major concerns in Malaysia as it becomes the second killing disease and causes huge number of death and spread to other regions of the world if left unchecked. In developed countries, infectious diseases are often preventable, but lack of medical devices in detecting it makes the death cases increase. The growth of different COVID-19 mutation has given so much challenges in detecting, preventing and curing. This gives motivation to researchers in order to solve this global problem by creating and advancing the detection tools and methods. Time, equipment availability, and the biological nature of COVID-19 influence the selection of appropriate detection techniques. This paper summarizes the comprehensive review on the type of diagnostic tests and biosensors available in detecting COVID-19 disease.

Abstract. Vulcanization and testing are important in the tire industry. This paper aims to reduce the total time of testing by considering the effect of rubberized vulcanization curing time on the peeling test. The experiment utilizes rubberized from natural rubber and polyester fabric as a sample. Furthermore, this paper investigates the shortest time which still maintains the standard properties of the product. This paper use nonfactorial Complete Randomized Design (CRD) with five variations of curing time including 20; 30; 40; 50; and 60 minutes. The results show that the duration of curing time affected the Force value and visualization of the peeling test. The result indicates that the most efficient rubberized curing time treatment was 30 minutes and obtained Force values 201 N, 216 N, 214 N, 201 N, and 211 N with an average of 208.6 N. Moreover, the result shows satisfactory adhesion characteristics in three category visualization values. Therefore, the sample met the company standard in both aspects of testingKeywords: Vulcanization, tire, curing time, peeling test, rubberized

Currently, the research on the application of Single point incremental forming technology (SPIF) in Vietnam is limited. Therefore, the study of technology and equipment for the fabrication of SPIF machine and research on the ability of deformation of the formed material sheet is necessary and should be urgently carried out. The paper proposes a new approach to modularizing the structure of the Single point incremental forming machine by using standard parts, thereby improving the quality and reducing the cost of the machine and improving accuracy of the machine.

Monosodium Glutamate (MSG) [1] was invented more than 100 years ago from its first invention in 1908 by Japanese biochemist Kikunae Ikeda, who was trying to isolate and duplicate the savory taste of kombu, an edible seaweed used as a base for many Japanese soups. From 2016, most MSG worldwide is produced by bacterial fermentation in a process similar to making vinegar or yogurt. Sodium is added later, for neutralization. During fermentation, Corynebacterium species, cultured with ammonia and carbohydrates from sugar beets, sugarcane, tapioca (cassava tuber) or molasses, excrete amino acids into a culture broth from which L-glutamate is isolated. In this process, Monosodium Glutamate companies buy cassava [2] pulps from farmers that contain a lot of sand and impurities. In order to increase the productivity with lowest expense, the filtration of sand and solid impurities’ is performed by separation cyclone. In this paper, we study all the measure to design a system of effective pump, cyclone to extract as much as possible all of solid impurities included sand out of cassava slurry before providing to the bacterial fermentation in a process.

This paper presents the simulation of beef freezing process by using ANSYS software. On the basis of simulation results, factors affecting the freezing time including air velocity and freezing temperature were determined. Within the air velocity range ω = (5÷15) m.s-1, an increase in the velocity by ω=1 m.s-1 led to a decrease in the freezing time by τ =(6,5÷2,0) %. When the freezing temperature was reduced by te = 1 K, the freezing time was reduced by τ = (3,2÷2,5) % in the freezing temperature range te = (–35÷–45) °C.

Cellulose is one of the main components of plants, depending on the plants, the cellulose content can be up to 98%. Cellulose has a wide range of use. It can be used in the food industries, pharmacy, paper, and chemical industries. To extract the cellulose from biomass, the biomass needs to undergo a pre-treatment. This study uses steam explosion pre-treatment as it does not cause hazards to the environment, has low energy cost, and low investment cost. In this pre-treatment, steam will be injected into the biomass until the pressure reach 15 bar, then decline rapidly to make an explosion that causes damage to cellulose crystalline. After that, the process continues to main process, which are washing, and alcohol extraction. Then continued to alcohol recovery. After considering many factors, a cellulose plant from rice straw will be built in 2023 in industrial parks Java Integrated Industrial and Ports Estate or known as JIIPE with a capacity of 370,000 tons/ year. Based on economic analysis, this plant has an internal rate of return of 35.17% and a payout time of 3.98 years. This makes this plant feasible to be built.

Due to the shortcomings of waste bricks, they cannot be used repeatedly. The brick powder can partially replace cement for construction production, which can solve the problem of cement energy consumption. This paper studies the influence of brick powder on the performance of cement-based materials. The research shows that the water absorption effect of brick powder and the friction force are the two main factors affecting concrete. Energy dispersive spectrometer, inductively coupled plasma mass spectrometry and compressive strength tests show that the addition of brick powder leads to the increase of silicon/calcium. inductively coupled plasma mass spectrometry shows that although brick powder dissolves in the early stage, the volcanic ash effect is weak. The results of mercury intrusion porosimetry and ultrasonic pulse velocity are consistent with the compressive strength. When 5 % is added, it shows excellent durability. In addition, with the increase of age, the durability will not decrease significantly. Since the brick powder only needs to be ground to avoid the related process of cement, good economic and environmental benefits can be obtained with the increase of substitution rate.

Incremental Sheet Forming (ISF) is emerging as one of the popular dieless forming processes for the small-sized batch production of sheet metal components. However, the parts formed by the ISF process suffer from poor surface finish, geometric inaccuracy, and non-uniform thinning, which leads to poor part characteristics. This paper deals with the influence of single point continuous local forming process parameters on the surface roughness of the product. Design of trials used for research planning and analysis and interpretation of results. The results indicate that the tool diameter (D), vertical step-down size (Δz), and sheet thickness (t) have significant effects on the produced profile accuracy, while the feed rate (f) is not significant. As a general rule, thin sheets with greater tool diameters yielded the best surface quality. The results also show that controlling all surface quality features is complex because of the contradicting effects of, and interactions between, a number of the process parameters.

Stress concentration is a complex problem in material mechanics, especially in Aeronautics and Astronautics applications, the concentrated stress will do great harm to the safe operation of the launch vehicle. Therefore, it is a common practice to simulate and verify the structural design or manufacturing process in the use of materials and dynamics. This paper first introduces the problem of stress concentration in aerospace, demonstrates the necessity and importance of studying this problem, at the same time, puts forward a stress concentration solution based on finite element method, which simplifies the geometric model by using symmetrical characte-ristics, so as to reduce the batch data of analysis. Compared with the conventional analysis using Patran and NASTRAN, its geometric model has a higher degree of discretization, The superiority and reliability of this method are verified by two examples. The results show that this finite element method is more accurate and effective in dealing with stress concentration problems, especially complex geometric models, and has high value for engineering practice.

Under the joint action of dynamic and static loads, the connecting bolts of the top cover of the pump turbine are prone to cumulative damage in local areas such as threads, resulting in cracks or development, and fatigue fracture may occur in severe cases, which will cause serious safety accidents. Therefore, it is necessary to carry out accurate fatigue life estimation analysis for connecting bolts, which has always been a hot spot and difficulty in the industry. This paper introduces several commonly used fatigue life analysis methods of parts, combined with the force characteristics and structural characteristics of the connecting bolts of the top cover, and analyzes and discusses the fatigue life analysis methods suitable for the top cover bolts. Finally, it is believed that the application of stress-strain field strength method can better describe the actual state of the bolt danger area, and the current damage state has an influence on the amount of damage generated by further loading, and the fatigue life analysis of connecting bolts can be combined with the stress-strain field strength method and variable damage linear cumulative damage theory, and the fatigue life and residual fatigue life can be estimated in the design stage or after the phased service of the bolt.

In this paper, by analyzing the structure and material characteristics of skid landing gear, the skid landing gear model is established by using CATIA software. In the explicit dynamic analysis type of ANSYS software, the force comparison between the impact surface of soil material and the impact surface of rigid material is made, combined with the change of momentum and energy in the process of touching the ground. This explains the necessity of landing drones on soft landing surfaces such as soil. In addition, LS-DYNA was used to simulate the dynamics of landing gear, and the strength of landing gear was analyzed according to failure criterion.

This paper introduces the rapid automatic control module of trawler based on the hydraulic system of ‘Zhejiang fishery scientific research ship No.2’.The hydraulic simulation model of double motor winch system is built in AMESim software, and SIMULINK module in MATLAB software designed closed loop fuzzy PID controller for hydraulic system simulation. through fuzzy PID control technology drives the hydraulic winch to quickly adjust the tension of the traction, maintain the stable balance of the traction force, maintain the optimization of network horizontal expansion, not only improve the fishing efficiency, but also timely and effective protection mesh. the technical achievements formed by the research will enable small and medium-sized trawlers to adjust the tension under various working conditions through the fuzzy PID control system to stabilize the opening shape of the trawl, so as to improve the automation level and fishing efficiency of related trawling equipment, and provide technical support for precision fishing.

In this paper, the on-line quality control feature of the injection molding machine based on the statistical process of thermoplastics product has been developed. The optimal process begins with collecting data and setting up the parameter of the injection machine according to the design of experiment. Four control parameters are set up on Demag Ergotech 200-840 Dragon. A series of tests using a body-outdoor led lamp has been conducted by means of both approaches simulation-based and experimental-based by which is injected using two-cavity injection mold. In simulation mode, clamping force and total weight were assigned as final responses, while total weight only is used as a response in experiment mode. The molded-parts were validated using thirty samples that are divided into a three-batch production process. The application of the on-line statistical quality check feature in the injection molding machine can be used as a quality control method by setting up barrel temperature, screw-back position, injection speed, and injection pressure.

Nowadays Wireless Sensor Networks (WSNs) are a very promising device to monitor environmental events, which are used in many application areas such as agriculture, environmental monitoring, air-water pollution, greenhouse, health monitoring, structural monitoring etc. Also, WSN needs effective and efficient way of collecting data from the area over which it is deployed, since the network consists of battery-operated nodes with limited energy. Improving the lifetime of WSN for continuous monitoring applications are very essential because of simple deployment, low installation cost, lack of cabling, and high mobility. The better energy conservation and reliable data transmission would be achieved in WSN by adopting efficient routing protocols for better and reliable communication. Also, security in data transmission in WSN is still a challenging task. Hence, a better way of encryption has to be computed to promote a reliable transmission between the nodes. In this paper discusses about different routing protocols which support energy efficiency and security techniques in WSN.

Direct-drive electric motor or In-Wheel Hub Motor (WHM) is gradually becoming popular as a new solution for electric propulsion. By meas of direct drive, the conventional transmission of belt or chain sprocket is not required to deliver the high torque requirement at the wheel. This paper studied metamodel machine leasning (MOP-ANN) implementation to predict the relationship model of geometries input of 42 slot/40 pole WHM with corresponding output performance. The multi-layer perceptron (MLP) of the neural network structure was trained to reveal the underlying pattern within the data sample. The sample data was obtained from a sensitivity analysis drive from FEA. The optimum geometry of the motor was directly solved by implementing a multiobjective optimization (MOO) method of genetic algorithm. Finnaly, the optimum geometry of the MOP-ANN based result is validated by FEA.

Alternative synthesis methods are need of the hour to provide easy protocol for synthesizing biologically active heterocyclic compounds. In this connection, this paper describes the development of a concise, convergent protocol for diversely substituted Suzuki–Miyaura cross-coupling reactions of heteroaryl bromides and boronic acids under microwave irradiation using Sodium aluminate (NaAlO2) as a solid support as well as base. According to my knowledge, this is the first report of the strategy that involves the use of zinc as a catalyst on fused tricyclic di-halo quinolones in a solvent-free condition using simple microwave irradiation. Earlier research from the same laboratory established a solid support assisted Suzuki–Miyaura cross-coupling reaction for forming C–C bonds under the influence of microwave irradiation. Therefore, sodium aluminate (NaAlO2) was attempted as a base and solid support instead of traditional mineral bases. Moreover, zinc was used as a catalyst replacing palladium. The new method is unique and effective due to its energy economy, procedural simplicity, and general applicability. Moreover, the use of Sodium aluminate (NaAlO2) is expected to extend this green-protocol and atom-friendly chemistry for the synthesis of varied heterocyclic compounds of interest.

The Smart Foundry concept promises benefits of improved foundry supply chain quality, more sustainable metal processing, and improved customer support. A significant need includes automated data gathering and visualization of the data. In metal foundries regardless of manufacturing small parts in mass production or big parts in small production, metal castings are difficult to trace individually. Furthermore, to identify causes of defects through statistical correlation of recorded process inputs to inspected part defects becomes challenging. In this paper we present a sand-casting Smart Foundry operation including automated scan-based tracking of cast parts through the foundry and supply chain. This allowed process data collected to be automatically associated with the part being processed. This study proved that additively manufactured tags can be utilized in foundry serial production operations for direct-part-marking of castings and both digital tracking and process data collection of individual cast parts. Further we made use of the captured part-by-part data to develop a root cause analysis for quality defect causal correlation. The results indicated that the casting feature dimensional quality was highly correlated with variations in sand bending strength, tin content in aluminum, and pouring time, among others. Such insights are available when tracking process and part data as part of a Smart Foundry.

This paper provides a complete overview of the entire process of designing a welding head moving device and its implementation as a semi-automatic welding machine. The mechanical structure of the device is designed based on the size of the material pipe and the accompanying technical requirements. The system is equipped with an arc generator set and a rotary speed control unit allowing its use as an orbital welder.

As the energy crisis's impact spreads, energy consumption has emerged as the fundamental impediment to industry's long-term viability. Utilizing and recovering various sources of waste heat can considerably reduce an organization's energy use. Energy conservation is crucial not just for fuel use, but also for the conservation and protection of the global ecosystem. As a result, it is necessary to make a concerted effort to save energy generated by waste heat. This paper aims to develop flue gas as a substitute for wood burning for drying mold at foundry shop of G-7 trading and industrial PLC. Flue gas temperature and velocity were measured at various locations throughout this study, and an analytical computation was done on the flue gas supply system and mold drying chamber. To show what happens within the hot flue gas supply duct and mould drying chamber, Computational Fluid Dynamics (CFD) Ansys software was used. The business benefits by eliminating the usage of wood as a fuel and making the process more cost-effective and environmentally friendly by capturing hot flue gas from the top section of the furnace or chimney and supplying it through duct to the drying chamber to dry the mold. As a result, the negative impact of deforestation will be mitigated, and a favorable working environment will be established.

Brakes have huge importance on a bike with regards to safety. Proper structural sturdiness and superior heat dissipating capabilities provide better performance while braking and longevity to the system. Transient thermal and structural analysis of four Indian two-wheeler disc brakes is completed by using ANSYS 2021 R2 student version software. The comparison results provide comprehensive insight into the thermal and structural characteristics of all four-disc rotors used in the industry. A comparative conclusion with respect to performance of each disc rotor in the respective components of the analysis like, temperature, heat-flux, total deformation and equivalent stress analysis is presented in this paper.