Search

This paper aimed to determine the characteristics of physical and mechanical properties of rice straw hand sheet and investigated the optimal conditions for making rice straw paper. The chemical composition of rice straw determined with the TAPPI standards. The conditions of making paper hand sheet composed of pulping time: 2 hours, 4 hours, pulping temperature: 100°C, 130°C, pulping solvent: 2 wt% NaOH, 4 wt% NaOH and bleaching: unbleached pulp, bleached pulp with 2% H2O2. The paper hand sheet was tested based on TAPPI methods, basic weight TAPPI- T410-om-93, thickness TAPPI- T411-om-89, moisture content TAPPI- T412-om-93, brightness TAPPI T452 om-92, opacity TAPPI standard T 425 om-91, burst strength TAPPI T403 om-97, tensile strength TAPPI T494 om-01, and tear strength TAPPI-T414-om-88. The results showed that the optimal conditions of rice straw hand sheet including pulping time: 2 hours, pulping temperature: 100°C, pulping solvent: 2 wt% NaOH, and bleaching: unbleached pulp gave the highest the physical and mechanical properties form other conditions. This conditions showed as the basic weight 62.27 g/m2, thickness 259.30 µ, opacity 93.34 ISO%, burst strength 64.75 kPa.m2/g, tensile strength 95.33 N.m/g, and tear strength 473.55mN.m2/g. In this condition, the paper hand sheet used at the lowest concentration of pulping solvent and non-bleached, which reduces environmental pollution.

Anode surface plays important role for extracellular electron transfer (EET) of exoelectrogenic microbes in microbial fuel cell (MFC). In this report, the electrochemical performance of a TiO2 nanorod array modified carbon paper electrode (TiO2 NRs/CP) is greatly improved by controlled chemical etching process. The etching process keeps the array morphology but yields obvious hollows on tops of TiO2 nanorods. The etched electrode (TiO2 NRs-HOT/CP) exhibits better hydrophilicity than carbon paper (CP) and TiO2 NRs/CP electrode as seen from smaller contact angle (CA) and more attached microbes S.loihica PV-4. Meanwhile, the hollows allow higher local concentration of microbial self-secreted flavins that can act as electron mediators for interfacial electron transfer of PV-4 through in-direct pathway. Accordingly, PV-4 produces larger current density at TiO2 NRs-HOT/CP electrode with maximum current density of 0.038 mA cm –2, which was much higher than that at CP electrode, and almost five times higher than that at un-etched TiO2 NRs/CP electrode.

Panicum repens is a species of grass known by many common names, including torpedo grass, creeping panic, panic rampant, couch panicum, wainaku grass, quack grass, dog-tooth grass, and bullet grass. The paper has been made from non-wood materials for long times. This research was used Panicum repens for made grass pulp as non-wood fiber. The influence of sodium hydroxide (NaOH) concentrations on properties of pulp from Panicum repens was investigated under room temperature. NaOH concentration levels were varied at 0%, 5%, 10%, 15%, and 20%, respectively. Moreover, Paper pulp from Panicum repens was observed by scanning electron microscope (SEM). This research has controlled the length of fiber approximately 0.5-2.5 cm before soaked with NaOH concentration at 1 hour and soak with water for controlled pH value at 7-8. Paper pulp was formed on a sieve. The result showed that color of paper pulp made from Panicum repens was light brown and green. SEM showed that NaOH concentration affects the physical properties of paper pulp. Moreover, true density of paper pulp was also investigated in this research.

In order to study the corresponding relationship between the design and fashion of tea gift package, this paper will analyze and discuss the color design and packaging style of tea gift package. Besides, this paper will also do research on the cultural origin of tea and the value of package, and analyze the influence of package on consumers. Finally, based on the research, the author had design a tea gift package that is in accordance with the current trend. This study uses bright yellow and orange as predominant colors to present nobleness of tea of Alishan. The colors used on the packaging will render people associate with harvest in autumn.

In this study, we chose 12 commonly available paper towels from the local market. The compression properties of the paper towels were examined by Kawabata Evaluation System for Fabric (KES-F). Three compression properties namely: (i) compressional linearity (LC), (ii) compression energy (WC) and (iii) compressional resilience (RC) were examined. The experimental results revealed that the compression properties varied within the different paper towels. RC vlaue was used as the key property for discussing the compression properties of paper towels. When different compression properties were correlated and analysed, it was found that no relationship was noted within different compression properties. On the other hand, there was not significant statistically relationship between weight and thickness to RC. It is hope that the results from this study can help the indurstry to improve the compression properties of paper towels for local market.

In this study, 12 commercially available paper towels were collected from the local market. Their tensile properties were investigated by Kawabata Evaluation System for Fabric (KES-F). Four tensile properties namely: (i) extensibility (EMT), (ii) tensile energy (WT), (iii) tensile resilience (RT) and (iv) linearity of WT (LT) were evaluated. Experimental results revealed that the tensile properties varied within the products. EMT was used as the key property for discussing the tensile properties of paper towels. However, when the different tensile properties were correlated, it was found that WT/RT, WT/EMT and RT/EMT had strong Pearson correlation. In addition, there was no significant statistically relationship between weight and thickness to EMT. Based on this study, it can provide some information about the tensile properties of paper towels in local market which may help the industry for further improving the product quality.

12 commercially available paper towels were collected from the local market and studied in this paper. Kawabata Evaluation System for Fabric (KES-F) was used for evaluating their bending properties. Two bending properties namely: (i) bending rigidity (B) and (ii) bending moment (2HB) were evaluated. Experimental results indciated that the bending properties varied within the products. B was used as the key property for discussing the bending properties of paper towels. When the correlations of different bending properties were investigated, it was found that no significant was found between B and 2HB. However, there was significant statistically relationship between weight and B but no relationship between thickness and B. With the use of the results, the product developer could improve the bending properties of the paper towels.

In this paper, we collected 12 commercially available paper towels from the local market and their shearing properties were evaluated by Kawabata Evaluation System for Fabric (KES-F). Three properties namely: (i) shear rigidity (G), (ii) shear stress at 0.5º (2HG) and (iii) shear stress at 5º (2HG5) were studied. Experimental results revealed that the shearing properties varied within the products. G was used as the key property for discussing the shearing properties of paper towels. However, in correlating different shearing properties, it was found that 2HG and 2HG5 had strong Pearson correlation. However, no significant statistically relationship between weight and thickness to G was found. This study may provide data for the industry for the improvement of shearing properties of paper towels for local market.

The quality of product of manufacturing industries depends on dimension accurately and surface roughness quality. There are many types of surface defects and levels of surface roughness quality. Ironing process is one type of metal forming process, which aims to reduce the wall thickness of the cup-shaped or pipes products, thus increasing the height of the wall. Manually surface inspection procedures are very inadequate to ensure the surface in guaranteed quality. To ensure strict requirements of customers, the surface defect inspection based on image processing techniques has been found to be very effective and popular over the last two decades. The paper has been reviewed some papers based on image processing for defect detection. It has been tried to find some alternatives of useful methods for product surface defect detection of ironing process.

Biocomposites sheets were prepared by compression molding from mixtures of corn starch plasticized by glycerol as matrix and cellulose fibers, extracted from used office paper, as reinforcement filler with contents ranging from 0 to 8% wt/wt of fibers to matrix. Properties of composites were determined by mechanical tensile test, differential scanning calorimetry, thermogravimetric analysis, water absorption measurement, and scanning electron microscopy. The results showed that higher fibers content raised the tensile strength and elastic modulus up to 109% and 112%, respectively, when compared to the non-reinforced thermoplastic starch (TPS). The addition of the fibers improved the thermal resistance and decreased the water absorption up to 63.6%. Scanning electron microscopy illustrated a good adhesion between matrix and fibers.