Search

To burn anthracite and reduce NO x emissions, a new combustion system was applied to a 300 MW e Babcock & Wilcox (B&W) down-fired boiler that included overfire air (OFA) and a decreased flow area of the inner and outer secondary air ducts of the installed swirl burners. Industrial-scale measurements (adjusting OFA ratios from 15.4% to 22.6%) were conducted to evaluate the overall performance of the retrofitted boiler. The experimental results demonstrated that the new combustion system promoted coal/air flow ignition and combustion stability. When the OFA ratio was less than 19.7%, the influence of the burner secondary air ratio on coal/air flow ignition was greater than that of the recirculation region below the arches. The overall combustion level in the primary combustion zone depended on the oxygen content and the recirculation region in the lower furnace instead of the early or late ignition of the coal/air flow. Oxygen and carbon monoxide concentration measurements in the near-sidewall region revealed that the fullness degree of the coal flame varied under different OFA ratios. Considering both environmental and economic effects, 19.7% was chosen as the optimal OFA ratio, thereby achieving a significant NO x reduction of 47% without increasing carbon content in the fly ash. [ABSTRACT FROM AUTHOR]

A new combustion system has been applied to a 300 MW e down-fired boiler with swirl burners to reduce NO x emissions. The unit provided the introduction of overfire air (OFA) and a decrease in the flow area of the inner and outer secondary air ducts of the swirl burners. Industrial experiments on the retrofitted boiler were performed at different loads. Full-scale measurements of the flue gas temperature distribution in the burner outlet region, the furnace temperature distributions measured by a pyrometer and the local mean gas species concentrations in the region near the sidewall were made at loads of 180, 250, and 300 MW e . The results show that the ignition distance increased with decreasing load, especially as the load decreased from 250 MW e to 180 MW e . At three different loads, the retrofitted coal/air flow could be all ignited in time at a distance in the range of 0.6–1.4 m from the burner outlet. Compared with the original combustion system, the ignition distance of the coal/air flow was significantly reduced at a load of 300 MW e . In addition, at a load of 300 MW e , the temperature of the boiler hopper was much higher than that at loads of 180 MW e and 250 MW e . Compared with the original combustion system, the upper furnace temperature decreased slowly with increasing measurement height at a load of 300 MW e after the retrofit. Measurements of the O 2 and CO concentrations in the region near the sidewall indicate that the fullness degree of the coal flame in the furnace at different loads was different. After the retrofit, the reheat steam temperatures reached the design temperature of 541 °C at loads of 180 MW e and 250 MW e , and the average reheat steam temperatures increased by approximately 13 °C. Compared with the original combustion system, a significant NO x reduction (more than 40%) at different loads was achieved without increasing the levels of unburnt carbon in the fly ash. [ABSTRACT FROM AUTHOR]

Abstract: Industrial experiments were performed for a retrofitted 660MWe full-scale down-fired boiler. Measurements of ignition of the primary air/fuel mixture flow, the gas temperature distribution of the furnace and the gas components in the furnace were conducted at loads of 660, 550 and 330MWe. With decreasing load, the gas temperature decreases and the ignition position of the primary coal/air flow becomes farther along the axis of the fuel-rich pipe in the burner region under the arches. The furnace temperature also decreases with decreasing load, as does the difference between the temperatures in the burning region and the lower position of the burnout region. With decreasing load, the exhaust gas temperature decreases from 129.8°C to 114.3°C, while NO x emissions decrease from 2448 to 1610mg/m3. All three loads result in low carbon content in fly ash and great boiler thermal efficiency higher than 92%. Compared with the case of 660MWe before retrofit, the exhaust gas temperature decreased from 136 to 129.8°C, the carbon content in the fly ash decreased from 9.55% to 2.43% and the boiler efficiency increased from 84.54% to 93.66%. [Copyright &y& Elsevier]