Search

A simple, reliable, and low-cost fabrication method is proposed here for assembling paper-based electrochemical devices (PEDs) using a commercial desktop digitally controlled plotter/cutter, together with ordinary writing tools. Permanent markers (tips of 1 mm) were used to create effective hydrophobic barriers on paper, while micromechanical pencils (mounting 4B graphite leads, 0.5 mm in diameter) were adopted for automatically drawn precise reference, counter, and working carbon electrodes. Fabrication parameters, such as writing pressure and speed, were first optimized, and the electrochemical performance of these devices was then evaluated by using potassium hexacyanoferrate(II) as redox probe. The good interdevice reproducibility (4.8%) displayed by the relevant voltammetric responses confirmed that this strategy can be profitably adopted to easily assemble paper-based electrochemical devices in a highly flexible manner. The simplicity of the instrumentation used and the low cost of each single device (about $0.04), together with the speed of fabrication (about 2 min), are other important features of the proposed strategy. Finally, to confirm the effectiveness of this prototyping method for the analysis of real samples and rapid controls, PEDs assembled by this simple approach were successfully exploited for the analysis of vitamin B6 in food supplements. [ABSTRACT FROM AUTHOR]

We demonstrate the hybridization-induced fluorescence detection of DNA on an origami-based paper analytical device (oPAD). The paper substrate was patterned by wax printing and controlled heating to construct hydrophilic channels and hydrophobic barriers in a three-dimensional fashion. A competitive assay was developed where the analyte, a single-stranded DNA (ssDNA), and a quencherlabeled ssDNA competed for hybridization with a fluorophorelabeled ssDNA probe. Upon hybridization of the analyte with the fluorophore-labeled ssDNA, a linear response of fluorescence vs analyte concentration was observed with an extrapolated limit of detection <5 nM and a sensitivity relative standard deviation as low as 3%. The oPAD setup was also tested against OR/AND logic gates, proving to be successful in both detection systems. [ABSTRACT FROM AUTHOR]

We present a microfluidic paper analytical device (μPAD) that relies on flow in hollow channels, rather than through a cellulose network, to transport fluids. The flow rate in hollow channels is 7 times higher than in regular paper channels and can be conveniently controlled from 0 to several mm/s by balancing capillary and pressure forces. More importantly, the pressure of a single drop of liquid (0.2 mbar) is sufficient to induce fast pressure-driven flow, making hollow channels suitable for point of care diagnostics. We demonstrate their utility for simple colorimetric glucose and BSA assays in which the time for liquid transport is reduced by a factor of 4 compared to normal cellulose channels. [ABSTRACT FROM AUTHOR]

We report a plasmonic paper-based analytical platform with functional versatility and subattomolar (<10-18 M) detection limit using surface-enhanced Raman scattering as a transduction method. The microfluidic paper-based analytical device (μPAD) is made with a lithography-free process by a simple cut and drop method. Complex samples are separated by a surface chemical gradient created by differential polyelectrolyte coating of the paper. The μPAD with a starlike shape is designed to enable liquid handling by lateral flow without microchannel patterning. This design generates a rapid capillary-driven flow capable of dragging liquid samples as well as gold nanorods into a single cellulose microfiber, thereby providing an extremely preconcentrated and optically active detection spot. [ABSTRACT FROM AUTHOR]

A paper-based solid-phase assay is presented for transduction of nucleic acid hybridization using immobilized quantum dots (QDs) as donors in fluorescence resonance energy transfer (FRET). The surface of paper was modified with imidazole groups to immobilize QD-probe oligonucleotide conjugates that were assembled in solution. Green-emitting QDs (gQDs) were FRET-paired with Cy3 acceptor. Hybridization of Cy3-labeled oligonucleotide targets provided the proximity required for FRET-sensitized emission from Cy3, which served as an analytical signal. The assay exhibited rapid transduction of nucleic acid hybridization within minutes. Without any amplification steps, the limit of detection of the assay was found to be 300 fmol with the upper limit of the dynamic range at 5 pmol. The implementation of glutathione-coated QDs for the development of nucleic acid hybridization assay integrated on a paper-based platform exhibited excellent resistance to nonspecific adsorption of oligonucleotides and showed no reduction in the performance of the assay in the presence of large quantities of noncomplementary DNA. The selectivity of nucleic acid hybridization was demonstrated by single-nucleotide polymorphism (SNP) detection at a contrast ratio of 19 to 1. The reuse of paper over multiple cycles of hybridization and dehybridization was possible, with less than 20% reduction in the performance of the assay in five cycles. This work provides an important framework for the development of paper-based solid-phase QD-FRET nucleic acid hybridization assays that make use of a ratiometric approach for detection and analysis. [ABSTRACT FROM AUTHOR]

In this technical note, we describe a facile method for one-step fabrication of paper-based microfluidic devices, by simply using commercially available permanent markers and metal templates with specific patterns. The fabrication process involves only a single step of plotting pattern in paper; it can be typically finished within 1 min. The ink marks formed in the patterned paper will act as the hydrophobic barriers to define the hydrophilic flow paths or separate test zones. Various paper devices can be created by using different templates with corresponding patterns. Transparent adhesive tape-sandwiched devices could protect their assay surfaces from potential contamination. In the proof-of-concept experiments, circular paper test zones (~3 mm diameter) were fabricated for colorimetric and quantification detection of prostate-specific antigen (PSA) as a model target, based on dot-immunogold staining assays coupled with gold enhancement amplification. Several serum specimens were additionally evaluated with this new approach and the results were compared with the commercial chemiluminescence immunoassay, validating its feasibility of practical applications. Such a one-step plotting method for paper patterning does not require any specialized equipments and skills, is quite inexpensive and rapid, and thus holds great potential to find wide applications especially in remote regions and resource-limited environments such as small laboratories and private clinics. [ABSTRACT FROM AUTHOR]

Paper spray is a newly developed ambient ionization method that has been applied for direct qualitative and quantitative analysis of biological samples. The properties of the paper substrate and spray solution have a significant impact on the release of chemical compounds from complex sample matrices, the diffusion of the analytes through the substrate, and the formation of ions for mass spectrometry analysis. In this study, a commercially available silica-coated paper was explored in an attempt to improve the analysis of therapeutic drugs in dried blood spots (DBS). The dichloromethane/isopropanol solvent has been identified as an optimal spray solvent for the analysis. The comparison was made with paper spray using chromatography paper as substrate with methanol/water as solvent for the analysis of verapamil, citalopram, amitriptyline, lidocaine, and sunitinib in dried blood spots. It has been demonstrated that the efficiency of recovery of the analytes was notably improved with the silica coated paper and the limit of quantitation (LOQ) for the drug analysis was 0.1 ng mL-1 using a commercial triple quadrupole mass spectrometer. The use of silica paper substrate also resulted in a sensitivity improvement of 5-50-fold in comparison with chromatography papers, including the Whatman ET31 paper used for blood cards. Analysis using a hand-held miniature mass spectrometer Mini 11 gave LOQs of 10-20 ng mL-1 for the tested drugs, which is sufficient to cover the therapeutic ranges of these drugs. [ABSTRACT FROM AUTHOR]

This technical note describes a detailed study on wax printing, a simple and inexpensive method for fabricating microfluidic devices in paper using a commercially available printer and hot plate. The printer prints patterns of solid wax on the surface of the paper, and the hot plate melts the wax so that it penetrates the full thickness of the paper. This process creates complete hydrophobic barriers in paper that define hydrophilic channels, fluid reservoirs, and reaction zones. The design of each device was based on a simple equation that accounts for the spreading of molten wax in paper. [ABSTRACT FROM AUTHOR]

This paper presents an inkjet printing method for the fabrication of entire microfluidic multianalyte chemical sensing devices made from paper suitable for quantitative analysis, requiring only a single printing apparatus. An inkjet printing device is used for the fabrication of three-dimensional hydrophilic microfluidic patterns (550-μm-wide flow channels) and sensing areas (1.5 mm × 1.5 mm squares) on filter paper, by inkjet etching, and thereby locally dissolving a hydrophobic poly(styrene) layer obtained by soaking of the filter paper in a 1 wt % solution of poly(styrene) in toluene. In a second step, the same inkjet printing device is used to print "chemical sensing inks", comprising the necessary reagents for colorimetric analytical assays, into well-defined areas of the patterned microfluidic paper devices. The arrangement of the patterns, printed inks, and sensing areas was optimized to obtain homogeneous color responses. The results are "all-inkjet-printed" chemical sensing devices for the simultaneous determination of pH, total protein, and glucose in clinically relevant concentration ranges for urine analysis (0.46-46 μM for human serum albumin, 2.8-28.0 mM for glucose, and pH 5-9). Quantitative data are obtained by digital color analysis in the L*a*b* color space by means of a color scanner and a simple computer program. [ABSTRACT FROM AUTHOR]

Single-walled carbon nanotubes were examined as an adsorptive material for a thermally desorbed preconcentrator for organic vapors. The nanotubes were processed into a paper form and packed into a metal tube for flow- through sampling. Adsorbed vapors were released by a temperature-programmed desorption method and detected downstream with a flexural plate wave vapor sensor. The tested vapors, methyl ethyl ketone, toluene, and dimethyl methylphosphonate, were released from the packed column at different temperatures. The vapors were retained more strongly than previously observed for the widely used Tenax porous polymer, indicating a significant affinity of the single walled nanotubes for organic vapors. [ABSTRACT FROM AUTHOR]

The author reflects on visual color sensing, which is a form of analytical chemistry that involves titration indicators and pH paper. He states that the DNA hybridization-based specificity of this scheme attracts wide interest and a continuous stream of valuable research. He discusses that since 1996, there have been some innovations in the chemistry of making gold nanoparticles that brings out spectral and color changes.