Search

The coating process on food packaging paper is carried out to improve the food safety aspect from dangerous substance migration from food packaging into food. It can facilitate to increase its function and wide the potency of utilization. The coating materials commonly used are plastic and wax coatings. Chitosan as a natural polymer that has the binding properties both water and oil. Chitosan has polar and non-polar groups thus it is potential to be developed as a coating material for food packaging paper. The purpose of this study was to determine the physical-mechanical and antimicrobial properties of food packaging paper from oil palm empty fruit bunches pulp coated with chitosan. The parameters used were chitosan and pulp weight. The oil palm empty fruit bunch pulp was fibrillated with high speed blender then mixed with chitosan solution. The mixed solution was poured in the mold and dried in an oven at 60 °C for 24 hours. The results showed that increasing of chitosan content was coated paper increased physical and mechanical properties values. The more pulp content the higher the physical properties value, however the mechanical properties value tend to decrease. The antimicrobial activity of chitosan coated paper was evaluated by measuring the diameter of the inhibition zones. The results revealed that all tested samples showed growth inhibition zone againts to Escherichia coli and Staphylococcus aureus after 24 h incubation compared to commercial food packaging paper.

Indonesia has targeted to reach 23% of renewable energy share by 2025. In order to meet the target, many researchers have focused on the explorations of renewable energy resources. One of the potential solutions to meet the target is the agricultural wastes, include corn cobs and areca nut fiber. In this study, the calorific value of corn cobs and areca nut fiber are tested. The corn cobs and areca nut fiber are collected from the farmers in Sumatera Utara province of Indonesia. In addition, the Paper waste is also tested. A bomb calorimeter of IKA C6000 is used to measure the energy content of the biomass. The results show that the calorific value of Corn cobs and Areca nut fiber is 5573 Cal/g and 4946 Cal/g, respectively.By using the average yearly production of Corn and Areca nut, these calorific values similar to 4,539 TOE and 4,653 TOE, respectively. If the potency can be used to replace the coal as an alternative fuel, this potency will reduce the Greenhouse gas (GHG) emission. The potency of mitigation GHG by replacing Corncob and Areca nut fiber are 18,306 and 18,491 ton of CO2e.

Recycled paper mill effluent (RPME) contains high concentrations of organic matters and total solids, and therefore requires proper treatment prior to discharge. There is a lack of experimental data available on the biodegradation of solids contents of RPME and digested sludge in anaerobic reactors. In this study, the treatment of RPME was studied using five compartments modified anaerobic inclining-baffled reactor (MAI-BR). The compartmental profiles of TSS, VSS, TDS and lignin contents, and floc size were investigated at different influent chemical oxygen demand concentration (CODin) from 1,000 to 4,000 mg/L, and hydraulic retention time (HRT) from 3 to 1 days (corresponding to organic loading rate (OLR) from 0.33 to 4 g/L day). The results showed that the contents of TSS, VSS and lignin were the highest at Compartment 1 (14,818-32,130 mg/L), (6,772-20,548 mg/L) and (7-227 mg/L), and gradually decreased towards Compartment 5 (627-8,518 mg/L), (281-6,145 mg/L) and (7-22 mg/L), respectively. Conversely, the content of TDS was low at Compartment 1 (508-712 mg/L) and slightly increased towards Compartment 5 (531-836 mg/L). Throughout 126 days, the floc size at Compartmental 1 was increased from 104 to 731 µm, similarly for other compartments. These results concluded that Compartment 1 played a major role in the operation of MAI-BR treating RPME.Recycled paper mill effluent (RPME) contains high concentrations of organic matters and total solids, and therefore requires proper treatment prior to discharge. There is a lack of experimental data available on the biodegradation of solids contents of RPME and digested sludge in anaerobic reactors. In this study, the treatment of RPME was studied using five compartments modified anaerobic inclining-baffled reactor (MAI-BR). The compartmental profiles of TSS, VSS, TDS and lignin contents, and floc size were investigated at different influent chemical oxygen demand concentration (CODin) from 1,000 to 4,000 mg/L, and hydraulic retention time (HRT) from 3 to 1 days (corresponding to organic loading rate (OLR) from 0.33 to 4 g/L day). The results showed that the contents of TSS, VSS and lignin were the highest at Compartment 1 (14,818-32,130 mg/L), (6,772-20,548 mg/L) and (7-227 mg/L), and gradually decreased towards Compartment 5 (627-8,518 mg/L), (281-6,145 mg/L) and (7-22 mg/L), respectively. Conversely, t...

The blended learning (BL) services presented for the academic accreditation process of universities and other educational institutions is a policy that has been used rapidly in the educational area. This process represents a real challenge and a need for institutions to function by the challenges in the ways of development for the attainment of faculty and student satisfaction. The need for learning management systems (LMS) becomes a real advance to control the management of technological development. The purpose of this study is to overcome these challenges and speed up the whole e-learning process in a different manner. The study revealed the existence of an important gap between the important features of blended learning applications and the control management of LMS. The finding shows a systematic analysis of existing technologies and their effects on accreditation checkpoints approval for the underlying conception of the assessment processes involve perspectives that relate to what is now considered valuable or desirable concerning the institution of higher education.

Principal Component Analysis (PCA) is a commonly used unsupervised exploratory analysis technique. It is also frequently used in dimensionality reduction. This preliminary paper investigates the feasibility of three variants of PCA, i.e. independent PCA (iPCA), sparse PCA (sPCA), and sparse independent PCA (siPCA) on forensic classification of paper based on their IR spectral data. After that, Linear Discriminant Analysis (LDA) models were built using the Principal Components (PCs) produced by the PCA and the three aforementioned variants. The performances of all these four LDA models, i.e. PCA-DA, iPCA-DA, sPCA-DA and siPCA-DA, were evaluated via leave-one-out cross-validation on the data set. The results obtained show that iPCA-DA and siPCA-DA are the most effective models with 100.0% classification accuracy. Then, the effectiveness of siPCA and iPCA models was evaluated based on posterior probability used for predictions of class membership that were derived from leave-one-out cross-validation. As a conclusion, siPCA is identified as the best classification model.

Historians and librarians are interested in watermarks and mould surface patterns in historic papers, because they represent the “fingerprints” of antique papers. However, these features are usually covered or hidden by printing, writing or other media. Different techniques have been developed to extract the watermarks in the paper while avoiding interference from media on the paper. Beta radiography provides good results, but this method cannot be widely used because of radiation safety regulations and the long exposure times required due to weak isotope sources employed. In this work, two promising methods are compared which can be used to extract digital high-resolution images for paper watermarks and these are electron radiography and low energy X-ray radiography. For electron radiography a “sandwich” of a lead sheet, the paper object, and a film in a dark cassette, is formed and it is exposed at higher X-ray potentials (> 300 kV). The photoelectrons escaping from the lead sheet penetrate the paper and expose the film. After development, the film captures the watermark and mould surface pattern Images for the paper being investigated. These images are then digitized using an X-ray film digitizer. The film employed could potentially be replaced by a special type of imaging plate with a very thin protection layer to directly generate digital Images using computed radiography (CR). For the second method, a low energy X-ray source is used with the specimen paper placed on a digital detector array (DDA). This method directly generates a low energy digital radiography (DR) image. Both methods provide high quality images without interference from the printing media, and provide the potential to generate a “fingerprint” database for historical papers. There were nevertheless found to be differences in the images obtained using the two methods. The second method, using a low energy X-ray source, has the potential to be integrated in a portable device with a small footprint incorporating user safety requirements. Differences obtained using the two methods are shown and discussed.

EMG is a medical technique that measures muscle response or electrical activity in response to a nerve’s stimulation of the muscle [10]. In this paper we have classified multiple hand gestures using small number of electrodes. This report aims to review current use of EMG based control system and explain the existing challenges. The stages involved includes data acquisition, feature extraction, classification and controller. Some of the application includes Arm rehabilitation, game controller, wheel chair controllers, etc.

Lateral light scattering simulations of printed dots are analyzed using general radiative transfer theory. We investigated the appearance of a printed paper in relation to the medium parameters like thickness of the paper sample, its optical properties, and the asymmetry factor. It was found that the appearance of a print greatly depends on these factors making it either brighter or darker. A thicker substrate with higher single scattering albedo backed with an absorbing surface makes the dots brighter due to increased number of scattering events. Additionally, it is shown that the optical effects of print also depend on illuminating and viewing angles along with the depth of ink penetration. A larger single scattering angle implies less intensity and the dots appear much blurred due to the shadowing effect prominent when viewed from sides. A fully penetrated dot of the same extinction coefficient as a partial penetrated one is darker due to increased absorption. These results can be used in applications dealing with lateral light scattering.

Paper-based PbS photodetector sensitive in the visible spectrum is reported. Nanocrystalline PbS-on-paper devices are fabricated by a spin coating method on white paper (300 GSM) from a methanolic precursor solution. Photodetector cells of gap 0.2 cm and length 0.5 cm are prepared by drawing contacts by monolithic cretacolor 8B pencil. X-ray diffractometer confirmed the deposition of nanocrystalline PbS films with 14 nm crystallites. The SEM illustrated the uniform coating of nanocrystalline PbS thin films on cellulose fibres of papers having an average thickness of fibres are 10 µm. The linear J-V characteristics in dark and under illumination of light using graphite trace on nanocrystalline PbS-on-paper shows good ohmic contact. The resistivity of pencil trace is 30 Ω·cm. Spectral response measurements of photodetector reveal the excellent sensitivity from 400 to 700 nm with a peak at 550 nm. The best responsivity anddetectivity are 0.7 A/W and 1.4 × 1012 Jones respectively. These paper-based low-cost photodetectors devices have fast photoresponse and recovery without baseline deviation.

Here, we presented a novel, cost effective approach to fabricate flexible piezoelectric nanogenerator (NG) consisting of ZnS nanowires (NWs) grown upon cellulose. An output voltage of 4 V is generated from the nanocomposite paper (NC-paper) based NG. Subsequently, it has the capability to power Light Emitting Diode (LED) and charging up capacitor. The corresponding energy stored in the capacitor (1 µF) is 16 µJ. Thus, the fabricated NC-paper based NG can be used for smart textile structures, wearable and self-powered nanodevices.

The commercial telecommunication system in future would explore the electromagnetic spectrum with higher frequency than used now, because it requires higher speed of transmission data. Using the millimeter waves (mmW) with frequency ranging from 30 to 300 GHz, such requirement could be fulfilled. The upcoming 5G cellular technology is expected to use frequency 30 GHz or higher. Then materials with a specific characteristic at the mmW range are interesting to be explored and investigated. Here, we report the synthesis process of graphene/TiO2 deposited on paper and their transmission characteristics to the electromagnetic energy at frequency 27-40 GHz (Ka-Band). The reduced graphene oxide (rGO) was synthesized by a modified Hummers method with introduction of microwave irradiation in the process. rGO and TiO2 were mixed in ethanol solution and deposited on the paper by a spraying technique. Transmission coefficient of electromagnetic wave energy at Ka-Band was measured by using the millimeter vector networ...

An algorithm for constructing super-large semantic networks has been developed in current work. Algorithm was tested using the “Cosmos” category of the Internet encyclopedia “Wikipedia” as an example. During the implementation, a parser for the syntax analysis of Wikipedia pages was developed. A graph based on list of articles and categories was formed. On the basis of the obtained graph analysis, algorithms for finding domains of high connectivity in a graph were proposed and tested. Algorithms for constructing a domain based on the number of links and the number of articles in the current subject area is considered. The shortcomings of these algorithms are shown and explained, an algorithm is developed on their joint use. The possibility of applying a combined algorithm for obtaining the final domain is shown. The problem of instability of the received domain was discovered when starting an algorithm from two neighboring vertices related to the domain.

CdSe quantum dot has great potential in various applications especially for emitting devices. One example potential application of CdSe quantum dot is security label for anti-counterfeiting. In this work, we present a practical approach of security label on paper using one and two colors of colloidal CdSe quantum dot, which is used as stamping ink on various types of paper. Under ambient condition, quantum dot is almost invisible. The quantum dot security label can be revealed by detecting emission of quantum dot using photoluminescence and cnc machine. The recorded quantum dot emission intensity is then analyzed using home-made program to reveal quantum dot pattern stamp having the word ’RAHASIA’. We found that security label using quantum dot works well on several types of paper. The quantum dot patterns can survive several days and further treatment is required to protect the quantum dot. Oxidation of quantum dot that occurred during this experiment reduced the emission intensity of quantum dot patterns.

Selection of the most significant variables, i.e. the wavenumber, from an infrared (IR) spectrum is always difficult to be achieved. In this preliminary paper, the feasibility of genetic algorithms (GA) in identifying most informative wavenumbers from 150 IR spectra of papers was investigated. The list of selected wavenumbers was then employed in Linear Discriminant Analysis (LDA). GA procedure was repeated 30 times to get different lists of variables. Then the performances of LDA models were estimated via leave-one-out cross-validation. A total of six to eight wavenumbers were identified to be valuable variables in the GA procedures. All the 30 LDA models achieve correct classification rates between 97.3% to 100.0%. Therefore the GA-LDA model could be a suitable tool for differentiating white papers that appeared to be highly similar in their IR fingerprints.

We successfully developed a method utilizing colloidal CdSe nanocrystalline quantum dot for anti-counterfeiting label on a piece of glossy paper. We deposited numbers and lines patterns of toluene soluble CdSe quantum dot using rubber stamper on a glossy paper. The width of line pattern was about 1-2 mm with 1-2 mm separation between lines. It required less than one minute for deposited CdSe quantum dot on glossy paper to dry and become invisible by naked eyes. However, patterned quantum dot become visible using long-pass filter glasses upon excitation of UV lamp or blue laser. We characterized photoluminescence of line patterns of quantum dot, and we found that emission boundaries of line patterns were clearly observed. The error of line size and shape were mainly due to defect of the original stamper. The emission peak wavelength of CdSe quantum dot was 629 nm. The emission spectrum of deposited quantum dot has full width at half maximum (FWHM) of 30-40 nm. The spectra similarity between deposited quant...

In response to published reports about the decline in funding for space nuclear power, the Board of Directors of the American Institute of Aeronautics and Astronautics (AIAA) approved a position paper in March 1995 that recommends (1) development and support of an integrated space nuclear power program by DOE, NASA and DoD; (2) Congressional support for the program; (3) advocacy of the program by government and industry leaders; and (4) continuation of cooperation between the U.S. and other countries to advance nuclear power source technology and to promote safety. This position paper has been distributed to various people having oversight of the U.S. space nuclear power program.

Prior work has established the existence of a color-performance relationship in achievement contexts and has demonstrated its presence in some undergraduate course examinations. This study examines the manifestation of such a relationship in an introductory, 430-student, calculus-based electricity and magnetism course during which the paper color used in examinations was varied. In this report, we analyze three separate exams and differentiate between students’ multiple choice, written response, conceptual, and computational performances. Also considered are factors such as the time students require to complete exams and their confidence levels prior to and immediately following assessment. Performance in all categories appears to be independent of paper color.

In this paper we present an application of two Computational Intelligence Algorithms, namely Particle Swarm Optimization (PSO) Algorithm and Differential Evolution (DE) for finding and optimal solution to two optimization problems that occur in a paper industry. The first problem deals with the economic optimization of a hypothetical but realistic Kraft pulping process and in the second problem we have considered the optimization of Boiler load allocation problem. Both the problems form an integral part of paper making process. The simulation results show the efficiency and time effectiveness of DE and PSO.

Due to the rising difficulty of developing complex systems a lot of research has gone into the multi‐agent paradigm over the past decades, during which a vast array of approaches for developing such systems have been proposed. Despite this fact there seems to be a gap in the MAS community between solutions that provide for expressivity and those that offer generality. It is our opinion that embedding the MAS language into a functional language we can have the best out of both worlds: we can implement the desired semantics in an abstract way, allowing us to focus on the problem domain, i.e. complex, distributed MAS. Our approach is going to be layered: (i) we start from a statically typed functional language and build an EDSL that acts as an executable specification language for single agent entities; and (ii) develop a framework for workflow‐oriented coordination on top of the previous layer and investigate its use as a means of implementing agent organizations, focusing on coordination and communication.