Search

To fill the research gap in the mechanical and physical properties of different varieties of sweet potatoes at different points in the harvest period and to provide a theoretical basis for the design of key components of the sweet potato harvester, the physical properties of Su-Shu 16, Su-Shu 36, and Ning-Zi 4 during the harvest period were studied at three time points: 15 October, 25 October, and 4 November 2023. The moisture content of sweet potatoes was determined using the DGF30/7-IA electric hot air-drying oven. The results showed that the moisture content of sweet potatoes decreased with increasing growth time at three different time points during the harvest period. The moisture content of Su-Shu 16 was, on average, 12.74% higher than that of Su-Shu 36, while the moisture content of Ning-Zi 4 was, on average, 8.07% higher than that of Su-Shu 36. The density of Su-Shu 36 measured by the drainage method is greater than that of Su-Shu 16 and Ning-Zi 4, but the difference is relatively small, and the density tends to decrease slowly with the increase of growth time. Using an electronic universal testing machine, compression tests were conducted on Su-Shu 16, Su-Shu 36, and Ning-Zi 4 at loading speeds of 5 mm/min and 10 mm/min, respectively. The results showed that the compressive strength limit range of Su-Shu 36 was slightly higher than that of Su-Shu 16 and significantly higher than that of Ning-Zi 4. The Poisson’s ratio, elastic modulus, and shear modulus values of Su-Shu 16 and Su-Shu 36 were similar and much higher than those of Ning-Zi 4. Studying sweet potatoes’ growth and physical characteristics for different purposes can provide data references for the design of digging depth, working width, and conveyor chain gap of sweet potato harvesters, as well as data references for sweet potato simulation experiments.

In this study, a 4UM-120D electric leafy vegetable harvester was employed as the research object. An automatic control system was created to maintain the cutter’s height above the ground within ±2% of the desired value. The intention was to reduce the operators’ work intensity while improving the leafy vegetable harvester’s working quality. The automatic control system for the cutter height from the ground was explained, along with its structure and operating philosophy. MATLAB was used to establish the two-phase hybrid stepper motor’s mathematical electrical equation and mechanical equation models. An analysis was carried out on the fundamentals and differences between position PID and incremental PID control algorithms. Utilizing incremental PID in combination, the control strategy for the harvester cutter height from the ground was built, and an automatic control system was produced under the corresponding control strategy. The stability, accuracy, and rapidity of the automatic control system of the cutter height from the ground under the incremental PID control strategy were analyzed by simulating different actual working conditions with MATLAB/Simulink and taking the steady-state transition time as the evaluation index. The test results show that when the deviation between the current value and the set value was greater than 2%—that is, when the harvester was in the condition of suddenly crossing the ditch or suddenly climbing the slope—the automatic control system based on the incremental PID control strategy had a good dynamic response performance and stability. This resulted in the automatic control function of the harvester cutter height off the ground being achieved. When the rotation angle PID control algorithm’s proportional coefficient is Kp = 4.665, the rotation speed PID control algorithm’s proportional coefficient is Kp = 5.65 and its integral coefficient is Ki = 3.86, and the current PID control algorithm’s proportional coefficient is Kp = 0.5455 and its integral coefficient is Ki = 30.4578. The harvester abruptly crossed a ditch while operating steadily, and the automatic control system’s steady-state transition time for the height of the cutter off the ground was 1.0811 s. The harvester abruptly climbed a slope while operating steadily, and the automatic control system’s steady-state transition time for the height of the cutter off the ground was 1.1185 s. Data from the field tests revealed a degree of reliability in the simulation test results. The study offered a strategy for raising the harvester quality for leafy vegetables while lowering the operator workload.

The yield of sweet potato vines is large, making it a good source of food. However, it is difficult to harvest sweet potato vines due to creeping and intertwining. Therefore, according to the domestic sweet potato planting model, this paper designed a double roll sweet potato vine harvester which can complete the operations of vine picking, vine killing, conveying and header harvesting at one time. The machine adopts the process of front roll vine picking, rear roll vine killing and rod bar lifting. The key components of the vine picking device, vine killing device and lifting device were designed and calculated. A numerical simulation test of the vine harvesting process was carried out by using the discrete element numerical simulation method. It was determined that the length of the vine picking rod from the outside to the inside is 175 mm, 150 mm and 105 mm, respectively, and the inclination angle of the end is 160°. There are six vine killing knives on each vine killing knife plate. The inclination of the lifting device is 50°and the conveying speed is 3 m/s. Using the box Behnken experimental design method, taking the vine picking roller speed, vine killing roller speed and ground clearance as the experimental factors, and taking the sweet potato vine harvest rate, stubble height and potato injury rate as the evaluation indexes, a quadratic regression orthogonal test was carried out, the effects of various factors on the evaluation indexes were analyzed, and the experimental factors were optimized and verified. The experimental results showed that the optimal parameter combination is as follows: the rotation speed of vine picking roller should be 716 r/min, the rotation speed of vine killing roller should be 1960 r/min and the ground clearance should be 16 mm. With these parameters, the harvest rate of sweet potato vines is 93.1%, the stubble height is 29.5 mm and the potato injury rate is 0.174%. As such, the harvester meets the requirements for the mechanized harvesting of sweet potato vines and is of great significance as a light and simplified product for the sweet potato industry.