Search

Compared to traditional manual methods for assessing the cotton verticillium wilt (CVW) hazard level, utilizing deep learning models for foliage segmentation can significantly improve the evaluation accuracy. However, instance segmentation methods for images with complex backgrounds often suffer from low accuracy and delayed segmentation. To address this issue, an improved model, YOLO-VW, with high accuracy, high efficiency, and a light weight, was proposed for CVW hazard level assessment based on the YOLOv10n model. (1) It replaced conventional convolutions with the lightweight GhostConv, reducing the computational time. (2) The STC module based on the Swin Transformer enhanced the expression of foliage and disease spot boundary features, further reducing the model size. (3) It integrated a squeeze-and-excitation (SE) attention mechanism to suppress irrelevant background information. (4) It employed the stochastic gradient descent (SGD) optimizer to enhance the performance and shorten the detection time. The improved CVW severity assessment model was then deployed on a server, and a real-time detection application (APP) for CVW severity assessment was developed based on this model. The results indicated the following. (1) The YOLO-VW model achieved a mean average precision (mAP) of 89.2% and a frame per second (FPS) rate of 157.98 f/s in assessing CVW, representing improvements of 2.4% and 21.37 f/s over the original model, respectively. (2) The YOLO-VW model's parameters and floating point operations per second (FLOPs) were 1.59 M and 7.8 G, respectively, compressed by 44% and 33.9% compared to the original YOLOv10n model. (3) After deploying the YOLO-VW model on a smartphone, the processing time for each image was 2.42 s, and the evaluation accuracy under various environmental conditions reached 85.5%, representing a 15% improvement compared to the original YOLOv10n model. Based on these findings, YOLO-VW meets the requirements for real-time detection, offering greater robustness, efficiency, and portability in practical applications. This model provides technical support for controlling CVW and developing cotton varieties resistant to verticillium wilt. [ABSTRACT FROM AUTHOR]

Cutting-edge detection is a critical step in mechanized rice harvesting. Through visual cutting-edge detection, an algorithm can sense in real-time whether the rice harvesting process is along the cutting-edge, reducing loss and improving the efficiency of mechanized harvest. Although convolutional neural network-based models, which have strong local feature acquisition ability, have been widely used in rice production, these models involve large receptive fields only in the deep network. Besides, a self-attention-based Transformer can effectively provide global features to complement the disadvantages of CNNs. Hence, to quickly and accurately complete the task of cutting-edge detection in a complex rice harvesting environment, this article develops a Transformer Convolution Network (TCNet). This cutting-edge detection algorithm combines the Transformer with a CNN. Specifically, the Transformer realizes a patch embedding through a 3 × 3 convolution, and the output is employed as the input of the Transformer module. Additionally, the multi-head attention in the Transformer module undergoes dimensionality reduction to reduce overall network computation. In the Feed-forward network, a 7 × 7 convolution operation is used to realize the position-coding of different patches. Moreover, CNN uses depth-separable convolutions to extract local features from the images. The global features extracted by the Transformer and the local features extracted by the CNN are integrated into the fusion module. The test results demonstrated that TCNet could segment 97.88% of the Intersection over Union and 98.95% of the Accuracy in the unharvested region, and the number of parameters is only 10.796M. Cutting-edge detection is better than common lightweight backbone networks, achieving the detection effect of deep convolutional networks (ResNet-50) with fewer parameters. The proposed TCNet shows the advantages of a Transformer combined with a CNN and provides real-time and reliable reference information for the subsequent operation of rice harvesting. [ABSTRACT FROM AUTHOR]

Pineapple harvesting is a key step in pineapple field production. At present, pineapple fruits are usually picked manually. With decreasing labor resources and increasing production costs, machines have been used instead of manual picking approaches in the modern pineapple industry. This paper briefly describes the basic situation of pineapple planting worldwide. Based on the degree of automation of mechanized pineapple harvesting equipment, the main structural forms, core technologies, and operation modes of semi-automatic, automatic, and intelligent pineapple harvesting equipment are summarized. The research status and existing problems of key pineapple fruit picking robots, such as fruit recognition, maturity classification, positioning, and separation of pineapple fruits, are analyzed. Considering the problems of pineapple harvesting equipment, such as difficulty entering the ground, low harvesting efficiency, low picking success rate, and fruit damage, innovative future research directions for mechanized pineapple harvesting technology are proposed, such as combining agricultural machinery and agronomical principles, integrating mechanized, automated, and intelligent technology, and developing modular designs and generalized approaches. [ABSTRACT FROM AUTHOR]

The air-suction precision seeder for small seeds is a planting machine, characterized by precision, high efficiency, and ease of operation, that uses air suction technology to sow small grain seeds at set intervals and depths into the soil. However, the forced vibration, enhanced by the increase in the operating speed, affects the seeding accuracy of the seeder and limits the seeding efficiency. To study the influence of vibration conditions on the seed suction performance of the air-suction precision seeder, we developed a computational fluid dynamics–discrete element coupling method to construct a bidirectional fluid–solid coupling numerical simulation model of the seed suction process under vibration conditions. Within the range of operating speeds from 0.6 km/h to 8 km/h, we quantitatively studied the population movement under different vibration frequencies, vibration amplitudes, negative pressure values, and seeding disc speeds and verified the simulation model and its analysis results through bench tests. The numerical results show that the interaction between the vibration frequency, vibration amplitude, and negative pressure value has the most significant impact on the single-seed rate. In addition, via variance analysis and response surface analysis, the optimal range of negative pressure values for achieving high single-seed rates under different vibration frequencies (4~10 Hz), vibration amplitudes (3~7.5 mm), and seeding disc speeds (4~50 rpm) was determined. The results indicate that, rather than the higher the negative pressure value, the higher the seed suction rate, the optimal negative pressure value for achieving a high seed suction rate varies with the specific vibration frequencies and amplitudes. [ABSTRACT FROM AUTHOR]

Due to factors such as a small amount of fertilizer application during rice topdressing and slow machine speed, the ordinary fertilizer discharge device fails to distribute the fertilizer uniformly and accurately as required, making it difficult to meet the needs of precise rice topdressing. This research focuses on the development of an offset spiral tooth fertilizer discharge device suitable for rice topdressing. The study analyzes the amount of fertilizer discharged in one cycle, the fertilizer force, and the motion of the fertilizer particles. In order to enhance the uniformity of the fertilizer discharge device at a low speed and small volume, the discrete element method is employed to conduct experimental research on the key structural parameters that affect the one-cycle amount of discharged fertilizer and the dynamics of the fertilizer discharge device. Through single-factor tests, it was found that the angle, height, number of spiral teeth, and diameter of the fertilizer discharge wheel are closely associated with the fertilizer discharge performance. To further investigate the impact of these four parameters on the fertilizer discharge performance, a regression combination test of the four factors is conducted based on the range optimized by the single-factor tests. A multi-objective mathematical model, considering the key parameters of fertilizer uniformity coefficient, one-cycle amount of fertilizer, and fertilizer discharge torque, is established at three speeds: 20, 55, and 90 rpm. The response surface method is utilized to analyze the influence of the interaction factors on the fertilizer discharge performance. The optimal combination of the key structural parameters was determined as follows: spiral tooth angle of 35.42°, tooth height of 9.02 mm, discharge wheel diameter of 57.43 mm, and tooth amount of 9.37. The bench test results of the device, using the optimal parameter combination and a fertilizer discharge speed of 0–90 rpm, were obtained for four commonly used rice fertilizers. The maximum variation coefficient of fertilizer discharge was found to be 10.42%. The one-cycle amount of fertilizer discharge was measured to be 19.82 ± 0.72 (A Kang), 17.20 ± 0.69 (Ba Tian), 20.34 ± 0.54 (Yaran), and 14.51 ± 0.44 (granular urea). The fertilizer discharge torque remained stable. These results indicate that the achieved optimization meets the precise fertilizer application requirements and can provide technical support for precise topdressing operations. [ABSTRACT FROM AUTHOR]

To achieve high-frequency and effective inter-vehicle communication between harvesters and transport vehicles during cooperative harvesting, a protocol for wireless communication was designed by analyzing actual communication requirements. Two different wireless communication modes (radio and 4G) were selected for the hardware design; then, a Kalman Filter was designed based on real-time Dead-reckoning and inter-vehicle Communication data after delay Compensation (KFDCC). Finally, the relative longitudinal deviation between two vehicles was obtained and updated steadily at a 10 Hz frequency. By using the relative longitudinal deviation of two vehicles, calculated after aligning the UTC stamp with the local GNSS data from the harvester and transport vehicle as a comparative metric, accuracy evaluation experiments were conducted regarding radio and 4G. The maximum absolute errors of the KFDCC output value were 0.03783 and 0.07381 m, respectively, and the mean square errors were 0.00392 and 0.01317 m, respectively. Compared with systems without the KFDCC method, the mean square errors were reduced by 88.76% and 90.60%, respectively. The KFDCC method can also effectively solve the problems of data delay, packet loss, blockage, error, and so on, in wireless communication, and has short-time breakpoint endurance capabilities. Field experiments showed that the proposed method can provide accurate data support for the dynamic alignment and unloading processes of harvesters and transport vehicles, and it can also provide algorithmic support for real-time communication data fusion between different wireless communication modes. Overall, the inter-vehicle communication mode and data-processing method designed in this paper have good effects and adaptability, and they can guarantee that the whole process of autonomous harvesting operates properly. [ABSTRACT FROM AUTHOR]

Discrete element modelling (DEM) parameters are of great importance for the accurate prediction of soil properties and disturbance. This study aimed to provide an efficient method for accurately determining the DEM parameters of a paddy soil with a high moisture content (45.66%). The DEM parameters of the paddy soil modelled using the Hertz–Mindlin with JKR contact model were determined by using the Plackett–Burman (PB), steepest ascent, and central composite tests. The accuracies of the developed DEM models were evaluated using actual slumping tests. Based on the PB test, the surface energy of soil, coefficients of soil–soil rolling friction, and coefficients of soil–steel static friction exerted larger influences on the overall relative error (δZH). The optimization results showed that to achieve a minimum δZH (5.96%), the surface energy of soil, the coefficients of soil–soil rolling friction, and the coefficients of soil–steel static friction should be 0.808 J m−2, 0.11, and 0.6, respectively. The optimized DEM model had an overall relative error of 7.27% with a coefficient of variation of 1.32%, indicating that the DEM parameters of the calibrated paddy soil had good accuracy. [ABSTRACT FROM AUTHOR]

The identification method of rice seedling rows based on machine vision is affected by environmental factors that decrease the accuracy and the robustness of the rice seedling row identification algorithm (e.g., ambient light transformation, similarity of weed and rice features, and lack of seedlings in rice rows). To solve the problem of the above environmental factors, a Gaussian Heatmap-based method is proposed for rice seedling row identification in this study. The proposed method is a CNN model that comprises the High-Resolution Convolution Module of the feature extraction model and the Gaussian Heatmap of the regression module of key points. The CNN model is guided using Gaussian Heatmap generated by the continuity of rice row growth and the distribution characteristics of rice in rice rows to learn the distribution characteristics of rice seedling rows in the training process, and the positions of the coordinates of the respective key point are accurately returned through the regression module. For the three rice scenarios (including normal scene, missing seedling scene and weed scene), the PCK and average pixel offset of the model were 94.33%, 91.48%, 94.36% and 3.09, 3.13 and 3.05 pixels, respectively, for the proposed method, and the forward inference speed of the model reached 22 FPS, which can meet the real-time requirements and accuracy of agricultural machinery in field management. [ABSTRACT FROM AUTHOR]

Smart farming uses advanced tools and technologies such as intelligent agricultural machines, high-precision sensors, navigation systems, and sophisticated computer systems to increase the economic benefits of agriculture and reduce the associated human effort. With the increasing demands of individualized farming operations, the internet of things is a crucial technique for acquiring, monitoring, processing, and managing the agricultural resource data of precision agriculture and ecological monitoring domains. Here, an internet of things-based system scheme integrating the most recent technologies for designing a management platform for agricultural machines equipped with automatic navigation systems is proposed. Various agricultural machinery cyber-models and their corresponding sensor nodes were constructed in a pre-production phase. Three key enabling technologies—multi-optimization of agricultural machinery scheduling, development of physical architecture and software, and integration of the controller-area-network with a mobile network—were addressed to support the system scheme. A demonstrative prototype system was developed and a case study was used to validate the feasibility and effectiveness of the proposed approach. [ABSTRACT FROM AUTHOR]

This paper describes the physical and tensile properties of corn bracts during a whole harvest period by using two corn cultivars, aiming to realize efficient peeling with minimum energy performance and decrease the incidence of ear damage. The value range and change rule of tensile properties were obtained by combining mechanical experiments and numerical statistics. Meanwhile, mathematical models were established for tensile properties depending on bract moisture content and bract thickness. The experimental results show that the tensile properties of leaf blade were affected by the orientation between pulling force and longitudinal vein, and that parallel orientation was greater than perpendicular. Further, the tensile properties of leaf sheaths depended on the angle between pulling force and natural growth direction of the bract in the following order: 0° > 90° > 180°. A larger pulling force angle can improve the probability of bract fracturing at the root of leaf sheaths, which helps reduce bract residue on the peduncle. In addition, the fracture mechanisms of leaf blades and sheaths were expressed from physiological and morphological perspectives. The experimental results are believed to be able to provide theoretical guidance by which to design and optimize corn-peeling devices. [ABSTRACT FROM AUTHOR]

Existing devices for dry direct-seeded rice with film mulching in northern China have limitations such as imprecise sowing, unadjustable sowing depth, and seeding device blocking. In this regard, this study proposes a combined seeding method of 'mini shovel + telescopic pipe' for dry direct-seeded rice with film mulching. A precision seeder for dry direct-seeded rice with film mulching was developed through theoretical calculations, discrete element modelling (DEM) simulations, and field experiments. The configuration and diameter of the rollers were obtained. Twelve telescopic pipes were evenly distributed on the circumference of the roller, with a contact ratio exceeding one. This ratio reduced the slip rate of the roller effectively. Subsequently, DEM was used to develop a 33 central composite design. The response surface was established with the sowing depth as the response value. According to agronomic requirements, the sowing depth was set to 20 mm. The optimal combination of working parameters was obtained by optimizing the regression equation. The field experiments showed that the performance of the precision seeder for dry direct-seeded rice with film mulching satisfied the requirements of agricultural production, working stably and reliably. The developed device represents a useful solution for dry direct-seeded rice with film mulching. [ABSTRACT FROM AUTHOR]