Search

The work presents the results of a study on cavitation erosion (CE) resistance of two NiCrSiB self-fluxing powders deposited by oxy-acetylene powder welding on cast iron substrate grade EN-GJL-200. The mean hardness of deposits A-NiCrSiB, C-NiCrSiB is equal to 908 HV, 399 HV and exceeds those of EN-GJL-200 and X5CrNi18-10 reference specimens 197 HV and 209 HV, respectively. To study CE, the vibratory apparatus has been used and tests were conducted according to the ASTM G32 standard. Cavitation eroded surfaces were examined using a profilometer, optical and scanning electron microscopy. The research indicated that the CE resistance, expressed by the cumulative mass loss decreased in the following order C-NiCrSiB > A-NiCrSiB > X5CrNi18-10 > EN-GJL-200. Therefore, hardfacings were characterised by lower cumulative mass loss, in turn, higher CE resistance than the reference sample and therefore they may be applied as layers to increase resistance to cavitation of cast iron machine components. Results indicate that in the case of multiphase materials, hardness cannot be the main indicator for CE damage prediction while it strongly depends on the initial material microstructure. To qualitatively estimate the cavitation erosion damage (CEd) of NiCrSiB self-fluxing alloys at a specific test time, the following factors should be considered: material microstructure, physical and mechanical properties as well as surface morphology and material loss both estimated at specific exposure time. A general formula for the CEd prediction of NiCrSiB deposits was proposed.

The process of conjoined stress cycling and abrasive or erosive wear is encountered in industry. However, very scant attention has been paid till now to this issue. The paper presents two test rigs designed and built to cope with this experimental problem. Tests were carried out on the range of pure iron (Armco), carbon steels namely S235JR, C45, C70U, C80U, C110U and unalloyed cast steels (L40III, L45III and L50III). Tested iron-based alloys differ in chemical composition, microstructure and Brinell hardness ranging from 80HB to 350HB. Stress cycling caused strain hardening of ferrite in hypoeutectoid steels and thus reduced their abrasive wear loss. In the hypereutectoid steel stress cycling impaired integrity of the microstructure thus increasing abrasive wear loss. Alternating stresses enhanced ploughing and cutting micromechanisms of erosion. Tensile stress in the tested cast steel had a stronger effect on wear loss than the prior stress history.

В статті містяться результати випробувань основних типів сталей при терті по нежорстко закріплених частинках абразиву В статье содержаться результаты испытаний основных типов сталей при трении о нежостко закрепленные абразивные частицы The article contains the results of tests of the main types of steels by friction on non-rigidly fixed abrasive particles. The steel presents a wide field of application. The abrasive wear resistance of steel relies mainly on the microstructure, hardness as well as on the abrasive material properties. Moreover, the selection of a abrasion-resistant grade of steel still seems to be a crucial and unsolved problem, especially due to the fact that the actual operating conditions can be affected by the presence of different abrasive materials. The aim of this work was to determine the effect of different abrasive grit materials i.e. garnet, corundum and carborundum on the abrasive wear result of a commonly used in industry practice steels i.e. S235, S355, C45, AISI 304 and Hardox 500. The microstructure of the steel was investigated using light optical microscopy. Moreover, hardness was measured with Vickers hardness tester. Additionally, the size and morphology of the abrasive materials were characterized. The abrasion tests were conducted with the usage of T-07 tribotester (dry sand rubber wheel). The results demonstrate that the hardness and structure of steels and hardness of abrasive grids influenced the wear results. The abrasive wear behavior of steels was dominated by microscratching and microcutting wear mechanisms. The highest mass loss was obtained for garnet, corundum, and carborundum, respectively. The usage of various abrasives results in different abrasion resistance for each tested steel grade. The AISI 304 austenitic stainless steel presents an outstanding abrasive wear resistance while usage of corundum and Hardox 500 while using a garnet as abrasive material. The C45 carbon steel was less resistant than AISI 304 for all three examined abrasives. The lowest resistance to wear in garnet and carborundum was obtained for the S235JR and S355J2 ferritic-perlitic carbon steels and in corundum for Hardox 500 which has tempered martensitic structure.

The paper presents the test results of microstructure and resistance to abrasion and erosive wear of single and double-layer coatings with arc-coated powder wires on the iron matrix. It was shown that adhesion of coatings is in the range of 14.39 – 24.72 MPa. The closed porosity of the coatings determined from SEM images is in the range of 0.69 – 2.45% and was significantly lower than the porosity determined from the images obtained from the optical microscope, which was 5.49 – 8.11%. The 95 MXC coating’s hardness of the matrix was about 100HV0.05 higher compared to the AMI 100 coating matrix. The intensity of the erosion of AMI 100 coatings was lower than the intensity of the erosion of 95 MXC coatings.