Search

Abstract: A 30μm thick nanocrystalline coating (NC) with a composition identical to that of conventional coarse-grained 304 stainless steel (SS) was prepared via direct current magnetron sputtering (DCMS). The DCMS NC exhibited a typical columnar microstructure, with a mean grain size of ∼12nm in the plane normal to the growth direction. Comparison of the oxidation of the 304 NC with 304 SS (∼20μm in an average grain size) was investigated at temperatures (700–900°C) in flowing air with 0–40% H2O vapor. Catastrophic breakaway oxidation started from the upstream edge of the coarse-grained sample in wet air after an incubation period, due to the conversion of protective Cr-rich scale into non-protective Fe-rich one as a result of the water-vapor-promoted evaporation of chromia from scale. Increasing temperature or water-vapor concentration accelerated the appearance of breakaway oxidation. In contrast, breakaway oxidation did not occur in wet air for the DCMS NC, where abundant grain boundaries greatly enhanced the Cr diffusion to guarantee the stable growth of the Cr-rich scale. [Copyright &y& Elsevier]

Joining NiTi to Ti6Al4V is of great interest for applications in the biomedical and aerospace fields. Despite the importance, no joining techniques have been developed that avoid the formation of brittle intermetallics to produce high strength joints. In this work, Niobium was used as an interlayer to prevent the formation of these brittle phases when joining NiTi to Ti6Al4V. The presence of this interlayer ensured that crack free welds were obtained and no brittle intermetallic compounds were observed. The Niobium interlayer was of a much higher melting temperature than the base materials so the bulk Niobium did not melt during the joining process, acting as a diffusion barrier between the NiTi and Ti6Al4V. The laser was focused on the Ti6Al4V side of the joint, which joined the Ti6Al4V and Niobium by fusion welding. At this interface a (Ti, Nb) region was formed due to dilution of the Niobium and mixing with the Ti6Al4V. At the NiTi–Nb interface a eutectic reaction was responsible for joining. Mechanical testing of the joints revealed that the minimum tensile strength matched the ultimate tensile strength of the weakest material, Niobium. These results highlight new possibilities for the use of high melting point filler materials when joining NiTi to dissimilar materials, so that the formation of undesired phases can be avoided. [ABSTRACT FROM AUTHOR]

Abstract: We use phase-field models to characterize the microstructure present in magnesium AZ31 alloy solidified under welding conditions. We focus our attention on the study of the conditions under which a columnar-to-equiaxed transition (CET) is observed in resistance spot welds. Our simulations show how the size and shape of the columnar and equiaxed regions depend on factors such as cooling rate, temperature gradient and the nature of inoculant particles. Our results are compared with experimental observations. In addition, we contrast our findings with predictions from a previously developed steady-state model for the CET. [Copyright &y& Elsevier]

Abstract: The influence of additives on the reaction kinetics and microstructure refinement in LiBH4–MgH2 composites is investigated in detail. Indications of the rate-limiting processes during the reactions are obtained by comparison of the measured reaction kinetics with simulations with one specific rate-limiting process. The kinetics of the sorption reactions are derived from volumetric measurements as well as from in situ X-ray diffraction measurements. During desorption, the hydrogen is released at a constant rate, which is possibly correlated with the one-dimensional growth of MgB2 platelets. In contrast, the kinetic curves of the absorption reactions exhibit the typical shape of contracting-volume controlled kinetics. The microscopical interpretation of kinetic measurements are supported by transmission electron microscopy images confirming the formation of additive-nanostructures in the grain boundaries upon cycling. The present investigations underline the importance of the additives as nucleation substrates and the influence of microstructure on the reaction kinetics. [Copyright &y& Elsevier]