Search

Bulk-heterojunction nanoparticle dispersions in water or alcohol can be employed as eco-friendly inks for the fabrication of organic solar cells by printing or coating. However, one major drawback is the need for stabilizing surfactants, which facilitate nanoparticle formation but later hamper device performance. When surfactant-free dispersions are formulated, a strong limitation is imposed by the dispersion concentration due to the tendency of nanoparticles to aggregate. In this work, pyridine end-capped poly(3-hexylthiophene) (P3HT-Py) is synthesized and included as an additive for the stabilization of P3HT:indene-C 60 bis-adduct (ICBA) nanoparticle dispersions. In the presence of acetic acid (AcOH), a surface-active pyridinium acetate end-capped P3HT ion pair, P3HT-PyH + AcO - , is formed which effectively stabilizes the dispersion and hence allows the formation of dispersions with smaller nanoparticle sizes and higher concentrations of up to 30 mg/mL in methanol. The dispersions exhibit an enhanced shelf-lifetime of at least 60 days at room temperature. After the deposition of light-harvesting layers from the nanoparticle dispersions, the ion-pair formation is reversed at elevated temperatures leading to regeneration of P3HT-Py and AcOH. The AcOH evaporates from the active layer, while the performance of the corresponding solar cells is not affected by the residual P3HT-Py in the devices. Enhanced nanoparticle stability is achieved with only 0.017 wt % pyridine in the P3HT/ICBA formulation.

Controlling the nanoscale morphology of the photoactive layer by fine-tuning the molecular structure of semiconducting organic materials is one of the most effective ways to improve the power conversion efficiency of organic solar cells. In this contribution, we investigate the photovoltaic performance of benzodithiophene (BDT)-based p-type small molecules with three different side chains, namely alkyl-thio (BTR-TE), dialkylthienyl (BTR), and trialkylsilyl (BTR-TIPS) moieties substituted on the BDT core, when used alongside a nonfullerene acceptor. The side-chain changes on the BDT core are shown to have a profound effect on energy levels, charge generation, recombination, morphology, and photovoltaic performance of solid-state molecules. Compared with BTR and BTR-TIPS, BTR-TE-based single-junction binary blend solar cells show the best power conversion efficiency (PCE) of 13.2% due to improved morphology and charge transport with suppressed recombination. In addition, we also achieved relatively good performances for ternary blend solar cells with a PCE of 16.1% using BTR-TE as a third component. Our results show that side-chain modification has a significant effect on modulating active layer morphology, and in particular that thioether side-chain modification is an effective way to achieve optimum morphology and performance for organic photovoltaic (OPV) devices.

Phenyl-C 61 -butyric acid methyl ester (PCBM) is universally used as the electron-transport layer (ETL) in the low-cost inverted planar structure of perovskite solar cells (PeSCs). PCBM brings tremendous challenges in upscaling of PeSCs using industry-relevant methods due to its aggregation behavior, which undermines the power conversion efficiency and stability. Herein, we highlight these, seldom reported, challenges with PCBM. Furthermore, we investigate the potential of nonfullerene indacenodithiophene (IDT)-based molecules by employing a commercially available variant, 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3- d:2',3'- d']- s-indaceno[1,2- b:5,6- b'] dithiophene (ITIC), as a PCBM replacement in ambient-processed PeSCs. Films fabrication by laboratory-based spin-coating and industry-relevant slot-die coating methods are compared. Although similar power-conversion efficiencies are achieved with both types of ETL in a simple device structure fabricated by spin-coating, the nanofibriller morphology of ITIC compared to the aggregated morphology of PCBM films enables improved mechanical integrity and stability of ITIC devices. Upon slot-die coating, the aggregation of PCBM is exacerbated, leading to significantly lower power-conversion efficiency of devices than spin-coated PCBM as well as slot-die-coated ITIC devices. Our results clearly indicate that IDT-based molecules have great potential as an ETL in PeSCs, offering superior properties and upscaling compatibility than PCBM. Thus, we present a short summary of recently emerged nonfullerene IDT-based molecules from the field of organic solar cells and discuss their scope in PeSCs as electron or hole-transport layer.

In this study, the nanomorphology of fluorenyl hexa-peri-hexabenzocoronene:[6,6]-phenyl C61-butyric acid methyl ester (FHBC:PC61BM) absorber layers of organic solar cells was investigated. Different electron microscopical techniques, atomic force microscopy, and grazing incidence wide-angle X-ray scattering were applied for a comprehensive nanomorphology analysis. The development of the nanomorphology upon sample annealing and the associated change of the device performance were investigated. It was shown that the annealing process enhances the phase separation and therefore the bulk heterojunction structure. Due to π-π stacking, the FHBC molecules assemble into columnar stacks, which are already present before annealing. While the nonannealed sample consists of a mixture of homogeneously distributed PC61BM molecules and FHBC stacks with a preferential in-plane stack orientation, crystalline FHBC precipitates occur in the annealed samples. These crystals, which consist of hexagonal arranged FHBC stacks, grow with increased annealing time. They are distributed homogeneously over the whole volume of the absorber layer as revealed by electron tomography. The FHBC stacks, whether in the two phase mixture or in the pure crystalline precipitates, exhibit an edge-on orientation, according to results from grazing incidence wide-angle X-ray scattering (GIWAXS), dark-field transmission electron microscopy (DF TEM) imaging and selective area electron diffraction (SAED). The best solar cell efficiencies were obtained after 20 or 40 s sample annealing. These annealing times induce an optimized degree of phase separation between donor and acceptor material.

The practical application of organic photovoltaic (OPV) cells requires high throughput printing techniques in order to attain cells with an area large enough to provide useful amounts of power. However, in the laboratory screening of new materials for OPVs, spin-coating is used almost exclusively as a thin-film deposition technique due its convenience. We report on the significant differences between the spin-coating of laboratory solar cells and slot-die coating of a blue-green colored, low bandgap polymer (PGREEN). This is one of the first demonstrations of slot-die-coated polymer solar cells OPVs not utilizing poly(3-hexylthiophene):(6,6)-phenyl-C(61)-butyric acid methyl ester (PCBM) blends as a light absorbing layer. Through synthetic optimization, we show that strict protocols are necessary to yield polymers which achieve consistent photovoltaic behavior. We fabricated spin-coated laboratory scale OPV devices with PGREEN: PCBM blends as active light absorbing layers, and compare performance to slot die-coated individual solar cells, and slot-die-coated solar modules consisting of many cells connected in series. We find that the optimum ratio of polymer to PCBM varies significantly when changing from spin-coating of thinner active layer films to slot-die coating, which requires somewhat thicker films. We also demonstrate the detrimental impacts on power conversion efficiency of high series resistance imparted by large electrodes, illustrating the need for higher conductivity contacts, transparent electrodes, and high mobility active layer materials for large-area solar cell modules., (© 2012 American Chemical Society)

We have studied the performance of normal and inverted bulk-heterojunction solar cells with an active layer composed of a blend of poly[(4,4'-bis(2-ethylhexyl)dithieno[3,2-b:2',3'-d]silole)-2,6-diyl-alt-(2,1,3-benzothiadiazole)-4,7-diyl] (PDTS-BTD) and {6,6}-phenyl-C71 butyric acid methyl ester (PC(71)BM). For inverted cells, a thin layer of ZnO nanoparticles and MoO(3) were used as interlayers for the bottom cathode and the top anode respectively. To enhance the device performance, a thin film of 4,4',4″-tris[N-(3-methylphenyl)-N-phenylamino]triphenylamine (MTDATA) was used along with MoO(3) as an anode interlayer to improve the hole extraction from the photoactive layer to the anode. The inverted polymer solar cells with double interlayer exhibit a higher power conversion efficiency of 6.45% compared to the conventional cell of 4.91% due to efficient charge extraction and favorable vertical morphology of active layer blend. Our ultraviolet photoemission spectroscopy results indicate that the formation of band bending due to interlayer leads to the enhancement in hole extraction.