Search

This work aims to deal with the challenges associated with designing complementary bifunctional electrocatalysts and a separator/membrane that enables rechargeable zinc-air batteries (RZABs) with nearly solid-state operability. This solid-state RZAB was accomplished by integrating a bifunctional electrocatalyst based on Ru-RuO 2 interface nanoparticles supported on nitrogen-doped (N-doped) graphene (Ru-RuO 2 /NGr) and a dual-doped poly(acrylic acid) hydrogel (d-PAA) electrolyte soaked in KOH with sodium stannate additive. The catalyst shows enhanced activity and stability toward the two oxygen reactions, i.e., oxygen reduction and evolution reactions (ORR and OER), with a very low potential difference (Δ E ) of 0.64 V. The computational insights bring out the electronic factors contributing to the enhanced catalytic activity of Ru-RuO 2 /NGr based on the charge density difference (CDD) between the interfaces. The disadvantages of the existing solid-state RZABs, such as their limited lifespan brought on by passivation, dendritic growth, corrosion, and shape change, have also been taken into account. The introduction of the stannate additive to the electrolyte induced an in situ Zn-anode modification, which subsequently improved the interfacial stability of the ZABs and, hence, the battery life cycles. The experimental observations reveal that, during the charging process, the Sn nanoparticles enable the homogeneous Zn deposition on the surface of the anode. Thus, the in situ Zn-anode surface modification assisted in achieving a high-rate cycle capability, viz., the homemade catalyst-based system exhibited continuous charge-discharge cycles for 20 h at a current density of 2.0 mA cm -2 , with each cycle lasting for 5 min.

To improve the oxygen reduction reaction (ORR) performance in a proton-exchange membrane fuel cell (PEMFC) cathode with respect to mass activity and durability, a suitable electrocatalyst design strategy is essentially needed. Here, we have prepared a sub-three nm-sized platinum (Pt)-cobalt (Co) alloy (Pt 3 Co)-supported N-doped microporous 3D graphene (Pt 3 Co/pNEGF) by using the polyol synthesis method. A microwave-assisted synthesis method was employed to prepare the catalyst based on the 3D porous carbon support with a large pore volume and dense micro-/mesoporous surfaces. The ORR performance of Pt 3 Co/pNEGF closely matches with the state-of-the-art commercial Pt/C catalyst in 0.1 M HClO 4 , with a small overpotential of 10 mV. The 3D microporous structure of the N-doped graphene significantly improves the mass transport of the reactant and thus the overall ORR performance. As a result of the lower loading of Pt in Pt 3 Co/pNEGF as compared to that in Pt/C, the alloy catalyst achieved 1.5 times higher mass activity than Pt/C. After 10,000 cycles, the difference in the electrochemically active surface area (ECSA) and half-wave potential ( E 1/2 ) of Pt 3 Co/pNEGF is found to be 5 m 2 g Pt -1 (ΔECSA) and 24 mV (Δ E 1/2 ), whereas, for Pt/C, these values are 9 m 2 g Pt -1 and 32 mV, respectively. Finally, in a realistic perspective, single-cell testing of a membrane electrode assembly (MEA) was made by sandwiching the Pt 3 Co/pNEGF-coated gas diffusion layers as the cathode displayed a maximum power density of 800 mW cm -2 under H 2 -O 2 feed conditions with a clear indication of helping the system in the mass-transfer region (i.e., the high current dragging condition). The nature of the I - V polarization shows a progressively lower slope in this region of the polarization plot compared to a similar system made from its Pt/C counterpart and a significantly improved performance throughout the polarization region in the case of the system made from the Pt 3 Co/NEGF catalyst (without the microwave treatment) counterpart. These results validate the better process friendliness of Pt 3 Co/pNEGF as a PEMFC electrode-specific catalyst owing to its unique texture with 3D architecture and well-defined porosity with better structural endurance.

Electrocatalytic oxidation of simple organic molecules offers a promising strategy to combat the sluggish kinetics of the water oxidation reaction (WOR). The low potential requirement, inhibition of the crossover of gases, and formation of value-added products at the anode are benefits of the electrocatalytic oxidation of organic molecules. Herein, we developed cobalt-nickel-based layered double hydroxide (LDH) as a robust material for the electrocatalytic oxidation of alcohols and urea at the anode, replacing the WOR. A facile synthesis protocol to form LDHs with different ratios of Co and Ni is adapted. It demonstrates that the reactants could be efficiently oxidized to concomitant chemical products at the anode. The half-cell study shows an onset potential of 1.30 V for benzyl alcohol oxidation reaction (BAOR), 1.36 V for glycerol oxidation reaction (GOR), 1.33 V for ethanol oxidation reaction (EOR), and 1.32 V for urea oxidation reaction (UOR) compared with 1.53 V for WOR. Notably, the hybrid electrolyzer in a full-cell configuration significantly reduces the overall cell voltage at a 20 mA cm -2 current density by ∼15% while coupling with the BAOR, EOR, and GOR and ∼12% with the UOR as the anodic half-cell reaction. Furthermore, the efficiency of hydrogen generation remains unhampered with the types of oxidation reactions (alcohols and urea) occurring at the anode. This work demonstrates the prospects of lowering the overall cell voltage in the case of a water electrolyzer by integrating the hydrogen evolution reaction with suitable organic molecule oxidation.

Recent advancements on the development of nonprecious electrocatalysts with iron (Fe) incorporated active centers have generated confidence on realizing cost-effective proton exchange membrane fuel cells (PEMFCs). However, most of these catalysts that emerged as a substitution for the platinum supported on carbon (Pt/C) catalysts in oxygen reduction reaction (ORR) are active under basic conditions, and their feasibility in PEMFCs remains as a challenge. In this scenario, this work reports the synthesis of a Pt-free oxygen reduction electrocatalyst prepared by the annealing of polydopamine grown melamine foam. The prepared catalyst has a three-dimensional (3D) interconnected bilayer network structure possessing the carbon nitride backbone wrapped by graphitic carbon layer bearing iron carbides and nitrides as the active centers (3D-FePDC). Interestingly, the 3D-FePDC catalyst displayed an ORR activity both under acidic and basic conditions. Whereas the ORR performance of 3D-FePDC closely matches that of the commercial Pt/C in the basic medium, it displays only a low overpotential value of 60 mV under acidic conditions compared to its Pt counterpart. The kinetics of ORR on 3D-FePDC is found to be similar to the four-electron (4e) reduction pathway displayed by Pt/C. Testing of a PEMFC in a single cell mode by using 3D-FePDC as the cathode catalyst and Nafion membrane delivered a maximum power density of 278 mW cm -2 , which is a promising value expected from a system based on the nonprecious metal cathode. Ultimately, as a cost-effective catalyst that can effectively perform irrespective of the pH conditions, 3D-FePDC offers significant prospects in the areas like fuel cells and metal-air batteries which work in acidic and/or basic conditions.

Electrochemical oxygen reduction in a selective two-electron pathway is an efficient method for onsite production of H 2 O 2 . State of the art noble metal-based catalysts will be prohibitive for widespread applications, and hence earth-abundant oxide-based systems are most desired. Here we report transition metal (Mn, Fe, Ni, Cu)-doped silicates, Sr 0.7 Na 0.3 SiO 3-δ , as potential electrocatalysts for oxygen reduction to H 2 O 2 in alkaline conditions. These novel compounds are isostructural with the parent Sr 0.7 Na 0.3 SiO 3-δ and crystallize in monoclinic structure with corner-shared SiO 4 groups forming cyclic trimers. The presence of Na stabilizes O vacancies created on doping, and the transition metal ions provide catalytically active sites. Electrochemical parameters estimated from Tafel and Koutechy-Levich plots suggest a two-electron transfer mechanism, indicating peroxide formation. This is confirmed by the rotating ring disc electrode method, and peroxide selectivity and Faradaic efficiency are calculated to be in the range of 65-82% and 50-68%, respectively, in a potential window 0.3 to 0.6 V (vs RHE). Of all the dopants, Ni imparts the maximum selectivity and efficiency as well as highest rate of formation of H 2 O 2 at 1.65 μmol s -1 .

Rechargeable aqueous zinc-metal batteries (ZMBs) are considered as potential energy storage devices for stationary applications. Despite the significant developments in recent years, the performance of ZMBs is still limited due to the lack of advanced cathode materials delivering high capacity and long cycle life. In this work, we report a low-temperature and scalable synthesis method following a surfactant-assisted route for preparing manganese-doped hydrated vanadium oxide (MnHVO-30) and its application as the cathode material for ZMB. The as-prepared material possesses a porous architecture and expanded interlayer spacing. Therefore, the MnHVO-30 cathode offers fast and reversible insertion of Zn 2+ ions during the charge/discharge process and delivers 341 mAh g -1 capacity at 0.1 A g -1 . Moreover, the MnHVO-30||Zn cell retains 82% of its initial capacity over 1200 stability cycles, which is higher compared to that of the undoped system. Besides, a quasi-solid-state home-made pouch cell with an area of 3.3 × 1.6 cm 2 and 3.6 mg cm -2 loading is assembled, achieving 115 mAh g -1 capacity over 100 stability cycles. Therefore, this work provides an easy and attractive way for preparing efficient cathode materials for aqueous ZMBs.

Novel cross-linked polymer electrolytes (XPEs) are synthesized by free-radical copolymerization induced by ultraviolet (UV)-light irradiation of a reactive solution, which is composed of a difunctional poly(ethylene glycol) diallyl ether oligomer (PEGDAE), a monofunctional reactive diluent 4-vinyl-1,3-dioxolan-2-one (VEC), and a stock solution containing lithium salt (lithium bis(trifluoromethanesulfonyl)imide, LiTFSI) in a carbonate-free nonvolatile plasticizer, poly(ethylene glycol) dimethyl ether (PEGDME). The resulting polymer matrix can be represented as a linear polyethylene chain functionalized with cyclic carbonate (dioxolanone) moieties and cross-linked by ethylene oxide units. A series of XPEs are prepared by varying the [O]/[Li] ratio (24 to 3) of the stock solution and thoroughly characterized using physicochemical (thermogravimetric analysis-mass spectrometry, differential scanning calorimetry, NMR, etc.) and electrochemical techniques. In addition, quantum chemical calculations are performed to elucidate the correlation between the electrochemical oxidation potential and the lithium ion-ethylene oxide coordination in the stock solution. Later, lithium bis(fluorosulfonyl)imide (LiFSI) salt is incorporated into the electrolyte system to produce a dual-salt XPE that exhibits improved electrochemical performance, a stable interface against lithium metal, and enhanced physical and chemical characteristics to be employed against high-voltage cathodes. The XPE membranes demonstrated excellent resistance against lithium dendrite growth even after reversibly plating and stripping lithium ions for more than 1000 h with a total capacity of 0.5 mAh cm -2 . Finally, the XPE films are assembled in a lab-scale lithium metal battery configuration by using carbon-coated LiFePO 4 (LFP) or LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA) as a cathode and galvanostatically cycled at 20, 40, and 60 °C. Remarkably, at 20 °C, the NCA-based lithium metal cells displayed excellent cycling stability and good capacity retention (>50%) even after 1000 cycles.

The redox-active and porous structural backbone of covalent organic frameworks (COFs) can facilitate high-performance electrochemical energy storage devices. However, the utilities of such 2D materials as supercapacitor electrodes in advanced self-charging power-pack systems have been obstructed due to the poor electrical conductivity and subsequent indigent performance. Herein, we report an effective strategy to enhance the electrical conductivity of COF thin sheets through the in situ solid-state inclusion of carbon nanofibers (CNF) into the COF precursor matrix. The obtained COF-CNF hybrids possess a significant intermolecular π···π interaction between COF and the graphene layers of the CNF. As a result, these COF-CNF hybrids (DqTp-CNF and DqDaTp-CNF) exhibit good electrical conductivity (0.25 × 10 -3 S cm -1 ), as well as high performance in electrochemical energy storage (DqTp-CNF: 464 mF cm -2 at 0.25 mA cm -2 ). Also, the fabricated, mechanically strong quasi-solid-state supercapacitor (DqDaTp-CNF SC) delivered an ultrahigh device capacitance of 167 mF cm -2 at 0.5 mA cm -2 . Furthermore, we integrated a monolithic photovoltaic self-charging power pack by assembling DqDaTp-CNF SC with a perovskite solar cell. The fabricated self-charging power pack delivered excellent performance in the areal capacitance (42 mF cm -2 ) at 0.25 mA cm -2 after photocharging for 300 s.

Substituting the energy-uphill water oxidation half-cell with readily oxidizable urea-rich urine, a ground-breaking bridge is constructed, combining the energy-efficient hydrogen generation and environmental protection. Hence, designing a robust multifunctional electrocatalyst is desirable for widespread implementation of this waste to fuel technology. In this context, here, we report a simple tuning of the electrocatalytically favorable characteristics of NiCo-layered double hydroxide by introducing [MoS 4 ] 2- in its interlayer space. The [MoS 4 ] 2- insertion as well as its effect on the electronic structure tuning is thoroughly studied via X-ray photoelectron spectroscopy in combination with electrochemical analysis. This insertion induces overall electronic structure tuning of the hydroxide layer in such a way that the designed catalyst exhibited favorable kinetics toward all the required reactions of hydrogen generation. This is why our homemade catalyst, when utilized both as a cathode and anode to fabricate a urea electrolyzer, required a mere ∼1.37 V cell potential to generate sufficient H 2 by reaching the benchmark 10 mA cm -2 in 1 M KOH/0.33 M urea along with long-lasting catalytic efficiency. Other indispensable reason of selecting [MoS 4 ] 2- is its high-valent nature making the catalyst highly selective and insensitive to common catalyst-poisoning toxins of urine. This is experimentally supported by performing the real urine electrolysis, where the nanospike-covered Ni foam-based catalyst showed a performance similar to that of synthetic urea, offering its industrial value. Other intuition of selecting [MoS 4 ] 2- was to provide a ligand-based mechanism for hydrogen evolution half-cell [hydrogen evolution reaction (HER)] to preclude the HER-competing oxygen reduction. Another crucial point of our work is its potential to avoid the mixing of two explosive product gases, that is, H 2 and O 2 .

Flexible supercapacitors in modern electronic equipment require light-weight electrodes, which have a high surface area, precisely integrated redox moieties, and mechanically strong flexible free-standing nature. However, the incorporation of the aforementioned properties into a single electrode remains a great task. Herein, we could overcome these challenges by a facile and scalable synthesis of the convergent covalent organic framework (COF) free-standing flexible thin sheets through solid-state molecular baking strategy. Here, redox-active anthraquinone (Dq) and π-electron-rich anthracene (Da) are judiciously selected as two different linkers in a β-ketoenamine-linked two-dimensional (2D) COF. As a result of precisely integrated anthraquinone moieties, COF thin sheet exhibits redox activity. Meanwhile, π-electron-rich anthracene linker assists to improve the mechanical property of the free-standing thin sheet through the enhancement of noncovalent interaction between crystallites. This binder-free strategy offers the togetherness of crystallinity and flexibility in 2D COF thin sheets. Also, the synthesized porous crystalline convergent COF thin sheets are benefited with crack-free uniform surface and light-weight nature. Further, to demonstrate the practical utility of the material as an electrode in energy-storage systems, we fabricated a solid-state symmetrical flexible COF supercapacitor device using a GRAFOIL peeled carbon tape as the current collector.

Polyaniline (PANI) as a pseudocapacitive material has very high theoretical capacitance of 2000 F g -1 . However, its practical capacitance has been limited by low electrochemical surface area (ESA) and unfavorable wettability toward aqueous electrolytes. This work deals with a strategy wherein the high ESA of PANI has been achieved by the induction of superhydrophilicity together with the alignment of PANI exclusively on the surface of carbon fibers as a thin layer to form a hybrid assembly. Superhydrophilicity is induced by electrochemical functionalization of the Toray carbon paper, which further induces superhydrophilicity to the electrodeposited PANI layer on the paper, thereby ensuring a high electrode-electrolyte interface. The Toray paper is electrochemically functionalized by the anodization method, which generates a highly active electrochemical surface as well as greater wettability (superhydrophilic) of the carbon fibers. Because of the strong interaction of anilinium chloride with the hydrophilic carbon surface, PANI is polymerized exclusively over the surface of the fibers without any appreciable aggregation or agglomeration of the polymer. The PANI-Toray paper assembly in the solid-state prototype supercapacitor can provide a high gravimetric capacitance of 1335 F g -1 as well as a high areal capacitance of 1.3 F cm -2 at a current density of 10 A g -1 . The device also exhibits high rate capability, delivering 1217 F g -1 at a current density of 50 A g -1 and a high energy density of 30 W h kg -1 at a power density of 2 kW kg -1 .

Nitrogen containing mesoporous carbon obtained by the pyrolysis of graphene oxide (GO) wrapped ZIF-8 (Zeolitic Imidazolate Frameworks-8) micro crystals is demonstrated to be an efficient catalyst for the oxygen reduction reaction (ORR). ZIF-8 synthesis in the presence of GO sheets helped to realize layers of graphene oxide over ZIF-8 microcrystals and the sphere-like structures thus obtained, on heat treatment, transformed to highly porous carbon with a nitrogen content of about 6.12% and surface area of 502 m 2 /g. These catalysts with a typical micromeso porous architecture exhibited an onset potential of 0.88Vvs RHE in a four electron pathway and also demonstrated superior durability in alkaline medium compared to that of the commercial Pt/C catalyst. The N-doped porous carbon derived from GO sheathed ZIF-8 core-shell structures could therefore be employed as an efficient electrocatalyst for fuel cell applications.

The present work discloses how high-quality dispersion of fine particles of cobalt ferrite (CF) could be attained on nitrogen-doped reduced graphene oxide (CF/N-rGO) and how this material in association with a microporous carbon phase could deliver significantly enhanced activity toward electrochemical oxygen reduction reaction (ORR). Our study indicates that the microporous carbon phase plays a critical role in spatially separating the layers of CF/N-rGO and in creating a favorable atmosphere to ensure the seamless distribution of the reactants to the active sites located on CF/N-rGO. In terms of the ORR current density, the heat-treated hybrid catalyst at 150 °C (CF/N-rGO-150) is found to be clearly outperforming (7.4 ± 0.5 mA/cm(2)) the state-of-the-art 20 wt % Pt-supported carbon catalyst (PtC) (5.4 ± 0.5 mA/cm(2)). The mass activity and stability of CF-N-rGO-150 are distinctly superior to PtC even after 5000 electrochemical cycles. As a realistic system level exploration of the catalyst, testing of a primary zinc-air battery could be demonstrated using CF/N-rGO-150 as the cathode catalyst. The battery is giving a galvanostatic discharge time of 15 h at a discharge current density of 20 mA/cm(2) and a specific capacity of ∼630 mAh g(-1) in 6 M KOH by using a Zn foil as the anode. Distinctly, the battery performance of this system is found to be superior to that of PtC in less concentrated KOH solution as the electrolyte.

Here, we report an efficient strategy by which a significantly enhanced electrode-electrolyte interface in an electrode for supercapacitor application could be accomplished by allowing in situ polymer gel electrolyte generation inside the nanopores of the electrodes. This unique and highly efficient strategy could be conceived by judiciously maintaining ultraviolet-triggered polymerization of a monomer mixture in the presence of a high-surface-area porous carbon. The method is very simple and scalable, and a prototype, flexible solid-state supercapacitor could even be demonstrated in an encapsulation-free condition by using the commercial-grade electrodes (thickness = 150 μm, area = 12 cm(2), and mass loading = 7.3 mg/cm(2)). This prototype device shows a capacitance of 130 F/g at a substantially reduced internal resistance of 0.5 Ω and a high capacitance retention of 84% after 32000 cycles. The present system is found to be clearly outperforming a similar system derived by using the conventional polymer electrolyte (PVA-H3PO4 as the electrolyte), which could display a capacitance of only 95 F/g, and this value falls to nearly 50% in just 5000 cycles. The superior performance in the present case is credited primarily to the excellent interface formation of the in situ generated polymer electrolyte inside the nanopores of the electrode. Further, the interpenetrated nature of the polymer also helps the device to show a low electron spin resonance and power rate and, most importantly, excellent shelf-life in the unsealed flexible conditions. Because the nature of the electrode-electrolyte interface is the major performance-determining factor in the case of many electrochemical energy storage/conversion systems, along with the supercapacitors, the developed process can also find applications in preparing electrodes for the devices such as lithium-ion batteries, metal-air batteries, polymer electrolyte membrane fuel cells, etc.

Here, we report the preparation of a flexible, free-standing, Pt- and TCO-free counter electrode in dye-sensitized solar cell (DSSC)-derived from polyethylenedioxythiophene (PEDOT)-impregnated cellulose paper. The synthetic strategy of making the thin flexible PEDOT paper is simple and scalable, which can be achieved via in situ polymerization all through a roll coating technique. The very low sheet resistance (4 Ω/□) obtained from a film of 40 μm thick PEDOT paper (PEDOT-p-5) is found to be superior to the conventional fluorine-doped tin oxide (FTO) substrate. The high conductivity (357 S/cm) displayed by PEDOT-p-5 is observed to be stable under ambient conditions as well as flexible and bending conditions. With all of these features in place, we could develop an efficient Pt- and TCO-free flexible counter electrode from PEDOT-p-5 for DSSC applications. The catalytic activity toward the tri-iodide reduction of the flexible electrode is analyzed by adopting various electrochemical methodologies. PEDOT-p-5 is found to display higher exchange current density (7.12 mA/cm(2)) and low charge transfer resistance (4.6 Ω) compared to the benchmark Pt-coated FTO glass (2.40 mA/cm(2) and 9.4 Ω, respectively). Further, a DSSC fabricated using PEDOT-p-5 as the counter electrode displays a comparable efficiency of 6.1% relative to 6.9% delivered by a system based on Pt/FTO as the counter electrode.

Current low-temperature fuel cell research mainly focuses on the development of efficient nonprecious electrocatalysts for the reduction of dioxygen molecule due to the reasons like exorbitant cost and scarcity of the current state-of-the-art Pt-based catalysts. As a potential alternative to such costly electrocatalysts, we report here the preparation of an efficient graphene nanotube based oxygen reduction electrocatalyst which has been derived from single walled nanohorns, comprising a thin layer of graphene nanotubes and encapsulated iron oxide nanoparticles (FeGNT). FeGNT shows a surface area of 750 m(2)/g, which is the highest ever reported among the metal encapsulated nanotubes. Moreover, the graphene protected iron oxide nanoparticles assist the system to attain efficient distribution of Fe-Nx and quaternary nitrogen based active reaction centers, which provides better activity and stability toward the oxygen reduction reaction (ORR) in acidic as well as alkaline conditions. Single cell performance of a proton exchange membrane fuel cell by using FeGNT as the cathode catalyst delivered a maximum power density of 200 mW cm(-2) with Nafion as the proton exchange membrane at 60 °C. The facile synthesis strategy with iron oxide encapsulated graphitic carbon morphology opens up a new horizon of hope toward developing Pt-free fuel cells and metal-air batteries along with its applicability in other energy conversion and storage devices.

The most vital component of the fuel cells and metal-air batteries is the electrocatalyst, which can facilitate the oxygen reduction reaction (ORR) at a significantly reduced overpotential. The present work deals with the development of surface-tuned cobalt oxide (Co3O4) nanoparticles dispersed on nitrogen-doped graphene as a potential ORR electrocatalyst possessing some unique advantages. The thermally reduced nitrogen-doped graphene (NGr) was decorated with three different morphologies of Co3O4 nanoparticles, viz., cubic, blunt edged cubic, and spherical, by using a simple hydrothermal method. We found that the spherical Co3O4 nanoparticle supported NGr catalyst (Co3O4-SP/NGr-24h) has acquired a significant activity makeover to display the ORR activity closely matching with the state-of-the-art Pt supported carbon (PtC) catalyst in alkaline medium. Subsequently, the Co3O4-SP/NGr-24h catalyst has been utilized as the air electrode in a Zn-air battery, which was found to show comparable performance to the system derived from PtC. Co3O4-SP/NGr-24h catalyst has shown several hours of flat discharge profile at the discharge rates of 10, 20, and 50 mA/cm(2) with a specific capacity and energy density of ~590 mAh/g-Zn and ~840 Wh/kg-Zn, respectively, in the primary Zn-air battery system. In conjunction, Co3O4-SP/NGr-24h has outperformed as an air electrode in mechanical rechargeable Zn-air battery as well, which has shown consistent flat discharge profile with minimal voltage loss at a discharge rate of 50 mA/cm(2). The present results, thus demonstrate that the proper combination of the tuned morphology of Co3O4 with NGr will be a promising and inexpensive material for efficient and ecofriendly cathodes for Zn-air batteries.

Here, we report synthesis of a 3-dimensional (3D) porous polyaniline (PANI) anchored on pillared graphene (G-PANI-PA) as an efficient charge storage material for supercapacitor applications. Benzoic acid (BA) anchored graphene, having spatially separated graphene layers (G-Bz-COOH), was used as a structure controlling support whereas 3D PANI growth has been achieved by a simple chemical oxidation of aniline in the presence of phytic acid (PA). The BA groups on G-Bz-COOH play a critical role in preventing the restacking of graphene to achieve a high surface area of 472 m(2)/g compared to reduced graphene oxide (RGO, 290 m(2)/g). The carboxylic acid (-COOH) group controls the rate of polymerization to achieve a compact polymer structure with micropores whereas the chelating nature of PA plays a crucial role to achieve the 3D growth pattern of PANI. This type of controlled interplay helps G-PANI-PA to achieve a high conductivity of 3.74 S/cm all the while maintaining a high surface area of 330 m(2)/g compared to PANI-PA (0.4 S/cm and 60 m(2)/g). G-PANI-PA thus conceives the characteristics required for facile charge mobility during fast charge-discharge cycles, which results in a high specific capacitance of 652 F/g for the composite. Owing to the high surface area along with high conductivity, G-PANI-PA displays a stable specific capacitance of 547 F/g even with a high mass loading of 3 mg/cm(2), an enhanced areal capacitance of 1.52 F/cm(2), and a volumetric capacitance of 122 F/cm(3). The reduced charge-transfer resistance (RCT) of 0.67 Ω displayed by G-PANI-PA compared to pure PANI (0.79 Ω) stands out as valid evidence of the improved charge mobility achieved by the system by growing the 3D PANI layer along the spatially separated layers of the graphene sheets. The low RCT helps the system to display capacitance retention as high as 65% even under a high current dragging condition of 10 A/g. High charge/discharge rates and good cycling stability are the other highlights of the supercapacitor system derived from this composite material.

Ba2In2O5 brownmillerites in which the In site is progressively doped with Ce exhibit excellent oxygen reduction activity under alkaline conditions. Ce doping leads to structural changes advantageous for the reaction. Twenty-five percent doping retains the ordered structure of brownmillerite with alternate layers of tetrahedra and octahedra, whereas further increase in Ce concentration creates disorder. Structures with disordered oxygen atoms/vacancies are found to be better oxygen reduction reaction catalysts probably aided by isotropic ionic conduction, and Ba2In0.5Ce1.5O5+δ is the most active. This enhanced activity is correlated to the more symmetric Ce site coordination environment in this compound. Stoichiometric perovskite BaCeO3 with the highest concentration of Ce shows very poor activity emphasizing the importance of oxygen vacancies, which facilitate O2 adsorption, in tandem with catalytic sites in oxygen reduction reactions.

Herein, we report a simple and scalable synthesis of Co3O4 nanocubes possessing exposed low surface energy planes supported on nitrogen-doped graphene (Co3O4-NC/NGr) by a hydrothermal method as an efficient electrocatalyst for water oxidation. Three different types of morphologies of Co3O4 (i.e., nanocubes, blunt edge nanocubes and spherical particles) have been synthesized by systematically varying the reaction time. Subsequently, their catalytic activity toward oxygen evolution reaction (OER) has been screened in alkaline medium. Among the three different morphologies, the intermediate architecture (i.e., the blunt edged nanocubes designated as Co3O4-NC/NGr-12h) has shown the highest OER activity. The catalyst displayed an overpotential (η) of ∼280 mV at 10 mA/cm(2) in 1 M KOH solution, which is lower than that of the other prepared samples such as Co3O4-NC/NGr-3h (∼348 mV), Co3O4-NC/NGr-9h (∼356 mV), Co3O4-NC/NGr-24h (∼320 mV), Co3O4-NC/Gr-12h (∼300 mV) and Co3O4 (∼310 mV). Along with that, the electrochemical stability of the catalyst is also found to be remarkably good. The role of the low index planes of Co3O4 nanocubes (Co3O4-NC) and the importance of the doped nitrogen in the carbon framework for the uniform dispersion and direct coupling with Co3O4-NC have been examined. The controlled interplay of the exposed crystal planes of Co3O4 and its dispersion and synergistic interaction with the nitrogen-doped graphene are found to be the decisive factors in bringing in the modulated OER activity of the system.

Here we report an all-solid-state supercapacitor (ASSP) which closely mimics the electrode-electrolyte interface of its liquid-state counterpart by impregnating polyaniline (PANI)-coated carbon paper with polyvinyl alcohol-H2SO4 (PVA-H2SO4) gel/plasticized polymer electrolyte. The well penetrated PVA-H2SO4 network along the porous carbon matrix essentially enhanced the electrode-electrolyte interface of the resulting device with a very low equivalent series resistance (ESR) of 1 Ω/cm(2) and established an interfacial structure very similar to a liquid electrolyte. The designed interface of the device was confirmed by cross-sectional elemental mapping and scanning electron microscopy (SEM) images. The PANI in the device displayed a specific capacitance of 647 F/g with an areal capacitance of 1 F/cm(2) at 0.5 A/g and a capacitance retention of 62% at 20 A/g. The above values are the highest among those reported for any solid-state-supercapacitor. The whole device, including the electrolyte, shows a capacitance of 12 F/g with a significantly low leakage current of 16 μA(2). Apart from this, the device showed excellent stability for 10000 cycles with a coulombic efficiency of 100%. Energy density of the PANI in the device is 14.3 Wh/kg.