Search

Developing a diffusion barrier layer on material interfaces has potential applications in various fields such as in packaging materials, pharmaceuticals, chemical filtration, microelectronics, and medical devices. Although numerous physical and chemical methods have been proposed to generate the diffusion barrier layer, the complexity of fabrication techniques and the high manufacturing costs limit their practical utility. Here, we propose an innovative approach to fabricate the diffusion barrier layer by irradiating poly(dimethylsiloxane) (PDMS) with a mid-infrared (λ = 10.6 μm) CO 2 laser. This process directly creates a diffusion barrier layer on the PDMS surface by forming a heavily cross-linked network in the polymer matrix. The optimal irradiation conditions were investigated by modulating the defocusing distance, laser power, and number of scanning passes. The barrier thickness can reach up to 70 μm as observed by the scanning electron microscope (SEM). The attenuated total reflectance (ATR), electron dispersive X-ray (EDX), and X-ray photoelectron spectroscopy (XPS) analyses collectively confirmed the formation of the SiO x structure on the modified surface based on the decreased methyl group signal and the increased oxygen/silicon ratio. The diffusion test with the model drugs (rhodamine B and donepezil) demonstrated that the modified surface exhibits effective diffusion barrier properties and the rate of drug diffusion through the modified barrier layer can be controlled by the optimization of the irradiation parameters. This novel approach provides the possibility to develop a controllable diffusion barrier layer in a biocompatible polymer with prospective applications in the fields of pharmaceuticals, packing materials, and medical devices.

Potassium vanadium oxyfluoride phosphate of composition KVPO 4 F 0.5 O 0.5 was modified by a carbon coating to enhance its electrochemical performance. Two distinct methods were used, first, chemical vapor deposition (CVD) using acetylene gas as a carbon precursor and second, an aqueous route using an abundant, cheap, and green precursor (chitosan) followed by a pyrolysis step. The formation of a 5 to 7 nm-thick carbon coating was confirmed by transmission electron microscopy and it was found to be more homogeneous in the case of CVD using acetylene gas. Indeed, an increase of the specific surface area of one order of magnitude, low content of C sp 2 , and residual oxygen surface functionalities were observed when the coating was obtained using chitosan. Pristine and carbon-coated materials were compared as positive electrode materials in potassium half-cells cycled at a C/5 (C = 26.5 mA g -1 ) rate within a potential window of 3 to 5 V vs K + /K. The formation by CVD of a uniform carbon coating with the limited presence of surface functions was shown to improve the initial coulombic efficiency up to 87% for KVPFO 4 F 0.5 O 0.5 -C 2 H 2 and to mitigate electrolyte decomposition. Thus, performance at high C-rates such as 10 C was significantly improved, with ∼50% of the initial capacity maintained after 10 cycles, whereas a fast capacity loss is observed for the pristine material.

Maleic anhydride plasma polymer was deposited at the surface of carbon fibers and functionalized with vinyl and thiol groups to improve its adhesion strength with an acrylate matrix cured by an electron beam. A characterization of the fiber surface properties was done before and after coating (topography, surface chemistry, and surface energy). Sharp improvements of the interfacial shear strength (+ 120%), measured by a micromechanical test derived from the pull-out test, were obtained and, to the best of our knowledge, never reported before. The values were close to the ones obtained with a thermal cure. The comparison of this approach with other types of surface treatments (oxidation, grafting of coupling agents) enabled the establishment of a general strategy for the improvement of the interfacial adhesion in carbon fiber composites cured by an electron beam and potentially the improvement of their mechanical properties. This strategy is based on a high surface density of functionalities that are generating covalent bonding during the polymerization of the matrix and on the insertion of a polymer layer strongly attached to the fiber surface and acting as a buffer between the fiber surface and the matrix to counteract the generation of stress in the interphase.