Search

A novel lead-containing metal-organic framework (Pb-MOF) is synthesized through postmetalation of MOF-525. Postmetalation renders lead ions bound with the organic linker of MOF-525, which can serve as nucleation points to promote perovskite crystallization. The introduction of lead postmetalated MOF-525 (Pb-MOF) as a scaffold layer between compact TiO

Hybrid lead halide perovskites continue to attract interest for use in optoelectronic devices such as solar cells and light-emitting diodes. Although challenging, the replacement of toxic lead in these systems is an active field of research. Recently, the use of trivalent metal cations (Bi3+ and Sb3+) that form defect perovskites A3B2X9 has received great attention for the development of solar cells, but their light-emissive properties have not previously been studied. Herein, an all-inorganic antimony-based two-dimensional perovskite, Cs3Sb2I9, was synthesized using the solution process. Vapor-anion-exchange method was employed to change the structural composition from Cs3Sb2I9 to Cs3Sb2Br9 or Cs3Sb2Cl9 by treating CsI/SbI3 spin-coated films with SbBr3 or SbCl3, respectively. This novel method facilitates the fabrication of Cs3Sb2Br9 or Cs3Sb2Cl9 through solution processing without the need of using poorly soluble precursors (e.g., CsCl and CsBr). We go on to demonstrate electroluminescence from a device employing Cs3Sb2I9 emitter sandwiched between ITO/PEDOT:PSS and TPBi/LiF/Al as the hole and electron injection electrodes, respectively. A visible-infrared radiance of 0.012 W·Sr-1·m-2 was measured at 6 V when Cs3Sb2I9 was the active emitter layer. These proof-of-principle devices suggest a viable path toward low-dimensional, lead-free A3B2X9 perovskite optoelectronics.

Controlling circularly polarized (CP) states of light is critical to the development of functional devices for key and emerging applications such as display technology and quantum communication, and the compact circular polarization-tunable photon source is one critical element to realize the applications in the chip-scale integrated system. The atomic layers of transition metal dichalcogenides (TMDCs) exhibit intrinsic CP emissions and are potential chiroptical materials for ultrathin CP photon sources. In this work, we demonstrated CP photon sources of TMDCs with device thicknesses approximately 50 nm. CP photoluminescence from the atomic layers of tungsten diselenide (WSe2) was precisely controlled with chiral metamolecules (MMs), and the optical chirality of WSe2 was enhanced more than 4 times by integrating with the MMs. Both the enhanced and reversed circular dichroisms had been achieved. Through integrations of the novel gain material and plasmonic structure which are both low-dimensional, a compac...

The presence of toxic lead (Pb) remains a major obstruction to the commercial application of perovskite solar cells. Although antimony (Sb)-based perovskite-like structures A3M2X9 can display potentially useful photovoltaic behavior, solution-processed Sb-based perovskite-like structures usually favor the dimer phase, which has poor photovoltaic properties. In this study, we prepared a layered polymorph of Cs3Sb2I9 through solution-processing and studied its photovoltaic properties. The exciton binding energy and exciton lifetime of the layer-form Cs3Sb2I9 were approximately 100 meV and 6 ns, respectively. The photovoltaic properties of the layered polymorph were superior to those of the dimer polymorph. A solar cell incorporating the layer-form Cs3Sb2I9 exhibited an open-circuit voltage of 0.72 V and a power conversion efficiency of 1.5%-the highest reported for an all-inorganic Sb-based perovskite.

Inorganic–organic hybrid perovskite solar cells (PSCs) are promising devices for providing future clean energy because of their low cost, ease of fabrication, and high efficiencies, similar to those of silicon solar cells. These materials have been investigated for their potential use in bifacial PSCs, which can absorb light from both sides of the electrodes. Here, we fabricated bifacial PSCs featuring transparent BCP/Ag/MoO3 rear electrodes, which we formed through low-temperature processing using thermal evaporation methods. We employed a comprehensive optical distribution program to calculate the distributions of the optical field intensities with constant thicknesses of the absorbing layer in the top electrode configuration. The best PSC having a transparent BCP/Ag/MoO3 electrode achieved PCEs of 13.49% and 9.61% when illuminated from the sides of the indium tin oxide and BCP/Ag/MoO3 electrodes, respectively. We observed significant power enhancement when operating this PSC using mirror reflectors and...

In this manuscript we describe hybrid heterojunction solar cells, having the device architecture glass/indium tin oxide/poly(3,4-ethylenedioxythiopene)/poly(styrenesulfonic acid)/perovskite/[6,6]-phenyl-C61-butyric acid methyl ester/C60/2,9-dimethyl- 4,7-diphenyl-1,10-phenanthroline/Al, fabricated using lead halide perovskite obtained through spray-coating at a low precursor concentration. To study the relationship between the morphology and device performance, we recorded scanning electron microscopy images of perovskite films prepared at various precursor ratios, spray volumes, substrate temperatures, and postspray annealing temperatures. Optimization of the spray conditions ensured uniform film growth and high surface area coverage at low substrate temperatures. Lead halide perovskite solar cells prepared under the optimal conditions displayed an average power conversion efficiency (PCE) of approximately 9.2%, with 85% of such devices having efficiencies of greater than 8.3%. The best-performing device exhibited a short-circuit current density of 17.3 mA cm(-2), a fill factor of 0.63, and an open-circuit voltage of 0.93 V, resulting in a PCE of 10.2%. Because spray-coating technology allows large-area deposition, we also fabricated devices having areas of 60 and 342 mm(2), achieving PCEs with these devices of 6.88 and 4.66%, respectively.

For inorganic thermoelectric materials, Seebeck coefficient and electrical conductivity are interdependent, and hence optimization of thermoelectric performance is challenging. In this work we show that thermoelectric performance of PEDOT:PSS can be enhanced by greatly improving its electrical conductivity in contrast to inorganic thermoelectric materials. Free-standing flexible and smooth PEDOT:PSS bulky papers were prepared using vacuum-assisted filtration. The electrical conductivity was enhanced to 640, 800, 1300, and 1900 S cm(-1) by treating PEDOT:PSS with ethylene glycol, polyethylene glycol, methanol, and formic acid, respectively. The Seebeck coefficient did not show significant variation with the tremendous conductivity enhancement being 21.4 and 20.6 μV K(-1) for ethylene glycol- and formic acid-treated papers, respectively. This is because secondary dopants, which increase electrical conductivity, do not change oxidation level of PEDOT. A maximum power factor of 80.6 μW m(-1) K(-2) was shown for formic acid-treated samples, while it was only 29.3 μW m(-1) K(-2) for ethylene glycol treatment. Coupled with intrinsically low thermal conductivity of PEDOT:PSS, ZT ≈ 0.32 was measured at room temperature using Harman method. We investigated the reasons behind the greatly enhanced thermoelectric performance.

We proposed a facile film treatment with formic acid to enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) by 4 orders of magnitude. The effect of formic acid concentration on conductivity was investigated; conductivity increased fast with increasing concentration up to 10 M and then increased slightly, the highest conductivity being 2050 S cm(-1) using 26 M concentration. Formic acid treated PEDOT:PSS films also exhibited very high transmittances. The mechanism of conductivity enhancement was explored through SEM, AFM, and XPS. Formic acid with its high dielectric constant screens the charge between PEDOT and PSS bringing about phase separation between them. Increased carrier concentration, removal of PSS from the film, morphology, and conformation change with elongated and better connected PEDOT chains are the main mechanisms of conductivity enhancement. ITO-free polymer solar cells were also fabricated using PEDOT:PSS electrodes treated with different concentrations of formic acid and showed equal performance to that of ITO electrodes. The concentrated acid treatment did not impair the desirable film properties as well as stability and performance of the solar cells.

In this study, we have strategically designed and convergently synthesized two novel, symmetrical, and linear A-D-A-type π-conjugated donor molecules (TBDTCNR, TBDTCN), each containing a planar electron-rich 2-octylthiene-5-yl-substituted benzodithiophene (TBDT) unit as the core, flanked by octylthiophene units and end-capped with electron-deficient cyanoacetate (CNR) or dicyanovinyl (CN) units. We thoroughly characterized both of these materials and investigated the effects of the end groups (CNR, CN) on their optical, electrochemical, morphological, and photovoltaic properties. We then fabricated solution-processed bulk heterojunction organic solar cells incorporating TBDTCNR and TBDTCN. Among our tested devices, the one containing TBDTCNR and [6,6]-phenyl-C61-butyric acid methyl ester in a 1:0.40 ratio (w/w) exhibited the highest power conversion efficiency (5.42%) with a short-circuit current density (Jsc) of 9.08 mA cm(-2), an open circuit voltage (Voc) of 0.90 V, and an impressive fill factor (FF) of 0.66 under AM 1.5G irradiation (100 mW cm(-2)). The FFs of these solution-processed small-molecule organic solar cells (SMOSCs) are outstanding when compared with those recently reported for benzodithiophene (BDT)-based SMOSCs, because of the high crystallinity and excellent stacking properties of the TBDT-based compounds.