Search

The most effective way to achieve very high collision energies in a circular particle accelerator is to maximize the field strength of the main bending dipoles. In dipole magnets using Nb-Ti superconductor the practical field limit is considered to be 8-9 T. When Nb3Sn superconductor material is utilized, a field level of 15-16 T can be achieved. To further push the magnetic field beyond the Nb3Sn limits, High Temperature Superconductors (HTS) need to be considered in the magnet design. The most promising HTS materials for particle accelerator magnets are Bi2212 and REBCO. However, their outstanding performance comes with a significantly higher cost. Therefore, an economically viable option towards 20 T dipole magnets could consist in an 'hybrid' solution, where both HTS and Nb3Sn materials are used. We discuss in this paper preliminary conceptual designs of various 20 T hybrid magnet concepts. After the definition of the overall design criteria, the coil dimensions and parameters are investigated with finite element models based on simple sector coils. Preliminary 2D cross-section computation results are then presented and three main layouts compared: cos-theta, block, and common-coil. Both traditional designs and more advanced stress-management options are considered.

A future circular collider (FCC) with a center-of-mass energy of 100 TeV and a circumference of around 100 km, or an energy upgrade of the LHC (HE-LHC) to 27 TeV require bending magnets providing 16 T in a 50-mm aperture. Several development programs for these magnets, based on Nb3Sn technology, are being pursued in Europe and in the U.S. In these programs, cos-theta, block-type, common-coil, and canted-cos-theta magnets are explored; first model magnets are under manufacture; limits on conductor stress levels are studied; and a conductor with enhanced characteristics is developed. This paper summarizes and discusses the status, plans, and preliminary results of these programs.

A future circular collider (FCC) with a center-of-mass energy of 100 TeV and a circumference of around 100 km, or an energy upgrade of the LHC (HE-LHC) to 27 TeV require bending magnets providing 16 T in a 50-mm aperture. Several development programs for these magnets, based on Nb3Sn technology, are being pursued in Europe and in the U.S. In these programs, cos-theta, block-type, common-coil, and canted-cos-theta magnets are explored; first model magnets are under manufacture; limits on conductor stress levels are studied; and a conductor with enhanced characteristics is developed. This paper summarizes and discusses the status, plans, and preliminary results of these programs.

A next step of energy increase of hadron colliders beyond the LHC requires high-field superconducting magnets capable of providing a dipolar field in the range of 16 T in a 50-mm aperture with accelerator quality. These characteristics could meet the requirements for an upgrade of the LHC to twice the present beam energy or for a 100-TeV center of mass energy future circular collider. This paper summarizes the activities and plans for the development of these magnets, in particular within the 16 T Magnet Technology Program, the WP5 of the EuroCirCol, and the U.S. Magnet Development Program.

A next step of energy increase of hadron colliders beyond the LHC requires high-field superconducting magnets capable of providing a dipolar field in the range of 16 T in a 50-mm aperture with accelerator quality. These characteristics could meet the requirements for an upgrade of the LHC to twice the present beam energy or for a 100-TeV center of mass energy future circular collider. This paper summarizes the activities and plans for the development of these magnets, in particular within the 16 T Magnet Technology Program, the WP5 of the EuroCirCol, and the U.S. Magnet Development Program.

A four-layer canted-cosine-theta 16-T dipole has been designed as a possible candidate for future hadron colliders. The design maintains part of the future-circular-collider magnet requirements, i.e., a 50 mm clear bore and 16 T operating at 1.9 K. The magnet intercepts Lorentz forces with an internal structure of ribs and spars, minimizes conductor, and reduces the number of layers and magnet size by using wide cables. The role of iron and its impact on field and magnet size is discussed. A three-dimensional magnetic analysis was carried out for 1-in-1 and 2-in-1 designs including a structural analysis for the 1-in-1 case. Thoughts on future improvements during winding are also discussed.

A four-layer canted-cosine-theta 16-T dipole has been designed as a possible candidate for future hadron colliders. The design maintains part of the future-circular-collider magnet requirements, i.e., a 50 mm clear bore and 16 T operating at 1.9 K. The magnet intercepts Lorentz forces with an internal structure of ribs and spars, minimizes conductor, and reduces the number of layers and magnet size by using wide cables. The role of iron and its impact on field and magnet size is discussed. A three-dimensional magnetic analysis was carried out for 1-in-1 and 2-in-1 designs including a structural analysis for the 1-in-1 case. Thoughts on future improvements during winding are also discussed.

In this paper we summarize the evolution and contributions of superconducting magnets to particle accelerators as chronicled over the last 50 years of Particle Accelerator Conferences (PAC, NA-PAC and IPAC). We begin with an historical overview based primarily on PAC Proceedings augmented with references to key milestones in the development of superconducting magnets for particle accelerators. We then provide some illustrative examples of applications that have occurred over the past 50 years, focusing on those that have either been realized in practice or provided technical development for other projects, with discussion of possible future applications.

In this paper we summarize the evolution and contributions of superconducting magnets to particle accelerators as chronicled over the last 50 years of Particle Accelerator Conferences (PAC, NA-PAC and IPAC). We begin with an historical overview based primarily on PAC Proceedings augmented with references to key milestones in the development of superconducting magnets for particle accelerators. We then provide some illustrative examples of applications that have occurred over the past 50 years, focusing on those that have either been realized in practice or provided technical development for other projects, with discussion of possible future applications.

A multilayer high field dipole magnet has been designed for future particle accelerators. The magnet has eight layers of a Nb3Sn outsert coil and four layers of a Bi-2212 insert coil (see Figs. 1 and 2). The layers are graded, delivering a short-sample field of 17.7 T in a 40-mm bore. The coil layers are of a canted cosine-theta design - with ribs and spars that guide and support the coil windings, shape the field, intercept Lorentz forces, and minimize conductor prestress. We present a general overview of the concept and report on the magnetic and mechanical design including an initial cost estimate and construction plan.

A multilayer high field dipole magnet has been designed for future particle accelerators. The magnet has eight layers of a Nb3Sn outsert coil and four layers of a Bi-2212 insert coil (see Figs. 1 and 2). The layers are graded, delivering a short-sample field of 17.7 T in a 40-mm bore. The coil layers are of a canted cosine-theta design - with ribs and spars that guide and support the coil windings, shape the field, intercept Lorentz forces, and minimize conductor prestress. We present a general overview of the concept and report on the magnetic and mechanical design including an initial cost estimate and construction plan.

A two-layer Canted-Cosine-Theta (CCT) superconducting dipole magnet was built and tested. The magnet's unique mandrel design uses machined channels and spars to guide the windings, intercept Lorentz forces, and circumvent tangential stress accumulation. The CCT magnet design provides a "near-perfect" current density distribution and requires minimal coil prestress. The CCT magnet design, with these inherent features, makes it a desirable option for a high field accelerator magnet. A two layer dipole (CCT1) using NbTi cable and a 50.8-mm clear bore was built and tested generating a 2.4 T dipole field. We report on the winding experience, measured field quality and quench history.

A two-layer Canted-Cosine-Theta (CCT) superconducting dipole magnet was built and tested. The magnet's unique mandrel design uses machined channels and spars to guide the windings, intercept Lorentz forces, and circumvent tangential stress accumulation. The CCT magnet design provides a "near-perfect" current density distribution and requires minimal coil prestress. The CCT magnet design, with these inherent features, makes it a desirable option for a high field accelerator magnet. A two layer dipole (CCT1) using NbTi cable and a 50.8-mm clear bore was built and tested generating a 2.4 T dipole field. We report on the winding experience, measured field quality and quench history.

In Free Electron Lasers (FEL), the electron trajectory through the undulator must meet stringent requirements in terms of trajectory wander and phase variation. This paper analyzes the feasibility of using line current pairs as correctors for superconducting undulators given a set of expected fabrication errors. A tolerance study has first been performed to investigate the impact of geometrical errors on the field quality. These errors are corrected with line currents that increase or decrease the magnetic field locally. Once the uncorrected trajectory is known, an algorithm finds the minimum number of correctors required to fulfill the trajectory specifications, and gives the corrector locations. All the correctors can be powered with the same current, greatly simplifying the implementation. The current then offers a degree of freedom to correct the trajectory and can be tuned dynamically as a function of the magnetic deflection.

The Superconducting Magnet Group, at Lawrence Berkeley National Laboratory (LBNL), has been developing a canted cosine-theta (CCT) superconducting dipole coil as well as the coil's supporting magnet structure. This contribution reports on the progress in the development of the coil's winding mandrel and its fabrication options. A comprehensive study of the coil's Lorentz forces was performed to validate the winding mandrel's "stress interception" attributes. The design of the external structure and the application of the "Bladder & Key" technology is also discussed. Additionally, the application of these studies to a curved ion-therapy CCT dipole magnet is reported.

The Superconducting Magnet Group, at Lawrence Berkeley National Laboratory (LBNL), has been developing a canted cosine-theta (CCT) superconducting dipole coil as well as the coil's supporting magnet structure. This contribution reports on the progress in the development of the coil's winding mandrel and its fabrication options. A comprehensive study of the coil's Lorentz forces was performed to validate the winding mandrel's "stress interception" attributes. The design of the external structure and the application of the "Bladder & Key" technology is also discussed. Additionally, the application of these studies to a curved ion-therapy CCT dipole magnet is reported.

In Free Electron Lasers (FEL), the electron trajectory through the undulator must meet stringent requirements in terms of trajectory wander and phase variation. This paper analyzes the feasibility of using line current pairs as correctors for superconducting undulators given a set of expected fabrication errors. A tolerance study has first been performed to investigate the impact of geometrical errors on the field quality. These errors are corrected with line currents that increase or decrease the magnetic field locally. Once the uncorrected trajectory is known, an algorithm finds the minimum number of correctors required to fulfill the trajectory specifications, and gives the corrector locations. All the correctors can be powered with the same current, greatly simplifying the implementation. The current then offers a degree of freedom to correct the trajectory and can be tuned dynamically as a function of the magnetic deflection.

The size and weight of ion-beam cancer therapy gantries are frequently determined by a large aperture, curved, ninety degree, dipole magnet. The higher fields achievable with superconducting technology promise to greatly reduce the size and weight of this magnet and therefore also the gantry as a whole. This paper reports advances in the design of winding mandrels for curved, canted cosine-theta (CCT) magnets in the context of a preliminary magnet design for a proton gantry. The winding mandrel is integral to the CCT design and significantly affects the construction cost, stress management, winding feasibility, eddy current power losses, and field quality of the magnet. A laminated mandrel design using a minimum symmetry in the winding path is introduced and its feasibility demonstrated by a rapid prototype model. Piecewise construction of the mandrel using this laminated approach allows for increased manufacturing techniques and material choices. Sectioning the mandrel also reduces eddy currents produced during field changes accommodating the scan of beam energies during treatment. This symmetry concept can also greatly reduce the computational resources needed for 3D finite element calculations. It is shown that the small region of symmetry forming the laminations combined with periodic boundary conditions can model the entire magnet geometry disregarding the ends. © 2013 Elsevier B.V.

The size and weight of ion-beam cancer therapy gantries are frequently determined by a large aperture, curved, ninety degree, dipole magnet. The higher fields achievable with superconducting technology promise to greatly reduce the size and weight of this magnet and therefore also the gantry as a whole. This paper reports advances in the design of winding mandrels for curved, canted cosine-theta (CCT) magnets in the context of a preliminary magnet design for a proton gantry. The winding mandrel is integral to the CCT design and significantly affects the construction cost, stress management, winding feasibility, eddy current power losses, and field quality of the magnet. A laminated mandrel design using a minimum symmetry in the winding path is introduced and its feasibility demonstrated by a rapid prototype model. Piecewise construction of the mandrel using this laminated approach allows for increased manufacturing techniques and material choices. Sectioning the mandrel also reduces eddy currents produced during field changes accommodating the scan of beam energies during treatment. This symmetry concept can also greatly reduce the computational resources needed for 3D finite element calculations. It is shown that the small region of symmetry forming the laminations combined with periodic boundary conditions can model the entire magnet geometry disregarding the ends. © 2013 Elsevier B.V.

The ability to correct magnetic field errors in a superconducting undulator is critical for the successful application of these devices in future and existing light sources. These field errors, which can emanate from sources such as machining and coil winding imperfections, can lead to reduced light source performance by introducing errors in both the electron trajectory and the relative phase relationship between the oscillating electrons and the emitted photons. In this work, correction schemes are presented, which use a single power supply along with a superconducting switch network to define the path for the current during undulator tuning. The basic switching concept was previously designed and successfully tested at Lawrence Berkeley National Laboratory; the approach presented here is a significant advancement in generalizing and scaling that core concept. A new fabrication method is presented here, which uses lithographic methods to produce current paths and switch heaters on a superconducting film. The effect of an example corrector current path design on the magnetic field is investigated using the Finite Element Method, and the results at various undulator and corrector energization levels are presented. Experimental results from the heater switch concept are also presented. © 2002-2011 IEEE.

The ability to correct magnetic field errors in a superconducting undulator is critical for the successful application of these devices in future and existing light sources. These field errors, which can emanate from sources such as machining and coil winding imperfections, can lead to reduced light source performance by introducing errors in both the electron trajectory and the relative phase relationship between the oscillating electrons and the emitted photons. In this work, correction schemes are presented, which use a single power supply along with a superconducting switch network to define the path for the current during undulator tuning. The basic switching concept was previously designed and successfully tested at Lawrence Berkeley National Laboratory; the approach presented here is a significant advancement in generalizing and scaling that core concept. A new fabrication method is presented here, which uses lithographic methods to produce current paths and switch heaters on a superconducting film. The effect of an example corrector current path design on the magnetic field is investigated using the Finite Element Method, and the results at various undulator and corrector energization levels are presented. Experimental results from the heater switch concept are also presented. © 2002-2011 IEEE.