Search

Abstract Renewable materials and material circularity are key priorities for the coming decades. While paper is the most utilized material in the packaging sector, its applications in food packaging are limited due to low barrier properties. Coating it with petroleum-based polymer barrier coatings renders it unrecyclable both mechanically and biologically. Bio-coated paper packaging, made from agricultural waste or by-products, presents environmentally favorable solutions that can benefit the biological cycle of the circular economy. The main objective of this study is to assess the applicability of grain and beer production by-products in wood pulp food packaging materials. It examines the effects of different grain by-products (industrial wheat grain processing residues and wheat bran) particles and concentrations (15 wt% and 40 wt%), as well as the impact of brewer’s yeast (Saccharomyces cerevisiae) at a concentration of 10 wt%, on the physical–mechanical and barrier properties of Northern bleached softwood kraft (NBSK) and chemithermomechanical (CTMP) pulps. Material composites were fabricated using a standard sheet forming method. Physical–mechanical properties were analyzed through tensile strength, strain at break, tear resistance, and bending stiffness tests. Barrier-related properties were analyzed through roughness, air permeance, and water contact angle tests. Results revealed that the vast majority of physical–mechanical properties decreased with the increase of both types of grain production fillers. Industrial wheat grain processing residues had a lower impact on physical–mechanical properties than wheat bran filler. A higher percentage of property decrease was absorbed in NBSK pulp than in CTMP. Roughness of CTMP can be improved by adding both industrial wheat grain processing residues and wheat bran. Wheat bran particles can increase hydrophobicity. CTMP pulp strength properties can be increased with the addition of yeast; however, the yeast additive’s effect on air permeance demonstrated a negative impact. In the case of NBSK pulp, which has higher primary strength properties, the addition of yeast does not make any significant changes. The conducted experiments demonstrated that, overall, the addition of these fillers resulted in a decline in physical–mechanical properties such as tensile strength, strain at break, tear resistance, and bending stiffness. This decline was more pronounced with higher concentrations of fillers. In the case of CTMP pulp, both types of fillers exhibited similar trends in affecting properties, whereas for NBSK pulp, wheat bran had a more significant impact compared to wheat grain processing residues. The addition of yeast generally led to a reduction in physical–mechanical properties, particularly in tensile strength and tear resistance. However, samples containing yeast displayed increased flexibility compared to controls. The influence on barrier properties varied: while yeast increased air permeability, it also enhanced surface hydrophobicity, thereby reducing the paper’s receptivity to liquids.

This article presents the information on the valorization of waste generated during the production of tissue paper. The possibility of bioconversion of the polysaccharide part of paper sludge into simple sugars has been evaluated. The options for processing the paper sludge before enzymic hydrolysis to achieve the maximum yield of monosaccharides have been considered. Pretreatment with acids has been found to be a key step before the biocatalytic cleavage of waste polysaccharides. An additional yield of enzymic hydrolysis products after pretreatment with acids has been obtained by pre-extraction of the paper sludge with spirit or acetone. It has been established that the most intense enzymic hydrolysis of readily available fractions of the paper sludge takes place in the first 10–12 hours. Further, the process slows down, probably due to the action of the remaining components of the fillers, as well as an increase in the proportion of the difficult-to-hydrolyze polysaccharide part. In all cases, the proportion of absolutely dry non-hydrolyzed residue has been about 43±2 % of the dry matter of the paper sludge. The main products of enzymic hydrolysis have been glucose and xylose. The resulting sugars have been used for mixotrophic cultivation of the Tetradesmus obliquus and Chlorella vulgaris algae. Yeast strains have been selected for the conversion of monosaccharides from the paper sludge. In a series of experiments on non-sterile yeast cultivation, the Candida utilis PAL D and Debaryomyces hansenii SWING R cultures have turned out to be the most productive (within 2.10±0.14 g of air-dry yeast weight/dm3 per 24 hours). The degree of conversion of hydrolysate sugars has been 70±2 %. Most of the remaining sugars (about 80 %) have been represented by xylose. Complete utilization of the sugars has taken place on the 2nd day when having added an extra nitrogen source to the medium. On the other hand, the spent nutrient medium after yeast separation has been suitable for mixotrophic cultivation of microalgae. It has been revealed that the economic costs of pre-treatment of the paper sludge with nitric acid can be leveled by using the resulting salts as a nitrogen source for cultivating yeast. In doing so, the yield of yeast biomass increases by almost 2 times.

Abstract The paper industry is a major environmental polluter due to paper waste sludge (PWS), often disposed of in hazardous ways. The techniques are employed to disposing of PWS are posing significant environmental hazards and risks to well-being. This study aims to evaluate PWS as a potential replacement for commercial adsorbents like AC and ZEO in treating stabilized leachate. Contact angle analysis of PWS was 92.60°, reveals that PWS to be hydrophobic. Batch adsorption experiments were conducted with parameters set at 200 rpm stirring speed, 120 min contact time, and pH 7. Optimal conditions for COD and NH3–N removal were identified at 120 min contact time, 200 rpm stirring speed, pH 7, and 2.0 g PWS ratio. Removal percentages for COD and NH3–N were 62% and 52%, respectively. Based on the results of the isotherm and kinetic studies, it was observed that the Langmuir and Pseudo second order (PSO) model exhibited greater suitability compared to the Freundlich and Pseudo first order (PFO) model, as indicated by higher values of R-squared (R2). The R-squared of Langmuir for COD and NH3–N were 0.9949 and 0.9919 and for Freundlich model were 0.9855 and 0.9828 respectively. Whereas the R-squared of PFO for COD and NH3–N were 0.9875 and 0.8883 and for PSO were 0.9987 and 0.9909 respectively.

As a way to reduce microplastics or nano-plastics in the ocean, it is of interest to develop biodegradable paper-based drinking straws to replace non-degradable plastic drinking straws. Primary questions to be addressed include how to design suitable coatings for paper drinking straws. Such coatings not only need to resist water. In addition, consumers have high expectations for the strength of a drinking straw. It is proposed here to replace non-biodegradable polypropylene, which is presently the main component of straws, with biodegradable and hydrophobic coating components via an entropy-driven approach. It is further proposed to develop colored paper-based drinking straws with cellulose nematic liquid crystal photonic pigments as a way to make the product stand out visibly, while at the same time mediating the usage of toxic chemical pigments.

This research was designed to assess the yield and quality of ash prepared from different types of waste papers. Waste newspapers, writing papers, and cartons were selected for combustion to obtain the ashes and coded as WNPA, WWPA, and WCPA, respectively. The waste papers were incinerated simultaneously in separate but identical incinerators at 850 ℃. An experiment on the yield of the ashes was performed on two days before the ashes obtained were mixed based on the type of waste papers from which they were derived. The results showed that irrespective of the day and time, the WCPA was the most yielded (14.1%), followed by the WWPA (12.3%), and then the WNPA (11.9%). Also, it was found that all the ashes possessed flow properties acceptable for engineering applications. However, the WCPA would ensure the best performance if applied, especially as a partial replacement material for cement. While the WWPA was found to be richer than the WNPA, the WCPA was the richest in terms of the proportions of key oxides for strength development. In general, the percentages of various chemical components of each ash complied with the standard specifications for cement except in the case of losses on ignition of the WNPA and WWPA, which were about 0.53% and 0.02%, respectively, beyond the maximum stipulated value.

Abstract To compare the urine Congo‐red dot paper test (CRD) with dipstick urinalysis to screen preeclampsia (PE). A total of 409 paired spot urine samples were obtained prospectively from women with suspected pre‐eclampsia attending for routine hospital visits. Congo‐red dot paper test and dipstick urinalysis were examined and compared to screen pre‐eclampsia. The agreement between the two urinary test is modest (kappa coefficient = 0.28, 95% CI 0.14–0.42). The specificity of CRD was higher than urinalysis (97.4% vs. 90.4%, p

Contemporary ESL education focuses on screen-based reading, specifically in the context of university level learners. Also, a sudden shift from paper bound reading activities to screen-based tasks was inevitable in response to COVID-19 outbreak. In this regard, the case of inferential and advanced level reading among the young ESL learners of developing countries appears researchable because of the general low digital literacy of these learners. This study, therefore, aimed to investigate the effect of reading mode shift from paper to screen on the inferential comprehension performance among Pakistani ESL learners at university level. A total of 426 undergraduate learners were sampled from Bachelor of Science program in a well-known university in the city of Lahore, Pakistan. Inferential reading was conceptualized through Bloom’s higher order thinking skills, that is, Analyzing, Evaluating and Creating skills therefore the reading comprehension test was based on these skills. Adopting sequential test administration, first the paper-based reading test, and later the screen-based reading was given. The obtained data were analyzed using Rendell’s XCALIBRE and SPSS V. 26.0. The logit scale descriptives, learner ability (θ), and mean scores demonstrated that the learners performed significantly higher in the paper test as compared to screen test. Moreover, it was found that the effect of reading mode shift was larger in Creating skill. The findings may have significant implications for reading mode selection, enhancement of digital competence and effect of reading mode shift in developing countries with inadequate IT facilitation and digital literacy among ESL learners.

The present study was conducted to draw the co-authorship network of hot papers of science citation index in the Web of Science (WOS) database from 2020 to 2021. This investigation is a descriptive study using a scientometrics approach. This research was conducted using social network analysis indices to visualize the co-authorship networks of hot papers in the science citation index. The structure of the co-authorship network of researchers of hot papers in the field of science consists of 47,045 authors who have contributed to the publication of 3475 hot papers from 2020 to 2021, which indicates the high co-authorship of these authors. Moreover, it was found that among the co-authorship patterns of these researchers, the most significant number of articles during the studied years was related to the five-author collaborations. Moreover, the average Collaboration Coefficient (CC) of the authors of hot papers was higher than 0.80, indicating the authors' strong tendency to produce joint articles. The high collaboration of the authors of hot papers in the science citation index can be one of the reasons for increasing the level of visibility and the potential for using them.

Reliable data on U.S. paper and cardboard waste by location and type are critical for developing waste-reduction solutions, but detailed geographic analysis is lacking in the literature. In this study, we employ statistical and geospatial methods to assess paper and cardboard waste in the United States by type at the national, state, county, and local levels. Of the estimated 110 million tons of paper and cardboard waste managed domestically in 2019, approximately 56% was landfilled, 6% was combusted, and 38% was recycled. The estimated market value of paper and cardboard lost to landfilling in 2019 was $4 billion, and the estimated losses of embodied energy and combustion energy were equivalent to 9% and 4% of U.S. primary industrial energy consumption, respectively. Associated landfilling fees amounted to almost $4 billion. This study aims to inform efforts to implement beneficial waste-management strategies by policy makers, researchers, businesses, and communities across the United States and to provide a model for similar studies in other parts of the world.

Introduction: Monitoring the atypical antipsychotic drug clozapine is crucial to ensure patient safety. This article showcases a high-throughput analytical method for measuring clozapine and its primary metabolite norclozapine (N-desmethylclozapine) in serum using paper spray mass spectrometry (PS-MS). Objectives: This study aimed to assess the viability of a PS-MS method for the rapid measurement of clozapine and norclozapine in human serum samples as an alternative to liquid chromatography mass spectrometry (LC-MS). Methods: Serum samples were processed by protein precipitation followed by deposition of the supernatant containing labelled internal standards onto paper spray substrates mounted in cartridges. Analytes were then analyzed using a triple quadrupole mass spectrometer equipped with a commercial paper spray ionization source. The results obtained from the patient samples were compared to those from a validated LC-MS assay. Results: PS-MS calibrations for clozapine and norclozapine were linear (R2 > 0.99) over five days. Between-run precision was below 8 %, and within-run precision did not exceed 10 %. When compared to a validated LC-MS method, the mean bias for 39 patient samples was −9% for clozapine and −1% for norclozapine, with no outliers. Mass spectrometry ion ratio comparisons indicated no interference for patient samples above the lower limit of quantification. There was less than 7 % change in the measured concentrations of both analytes over five days for samples dried on paper substrates. Notably, virtually no maintenance of the MS source was required during this study. Conclusion: This study illustrates the potential of PS-MS for serum drug monitoring in the clinical laboratory.

Besides scientific impact, papers can also achieve a technological impact that remains less known in the scientific community. Cited papers in the patents are considered as the index to measure the technological impact. This study aimed to analyze the technological impact of Iranian publications using co-authorship and co-word map, their evolution, the journals, and the subject areas of these publications. This applied research focuses on the quantitative study and visualization with a scientometric approach. The research population was all studies (4554 records) that were published during 2011-2020 in one of the Iranian institutions and had been cited by one of the international patents. The data collection tool was the SciVal database. CiteSpace and Excel spreadsheets were used to analyze the data. Of the 4,554 papers cited by the scholarly outputs that have been cited in patents e patents, most of them were published in collaboration with the USA (9%). Islamic Azad University and Tehran University of Medical Sciences (13% each) were the most active Iranian universities. The number of Iranian papers cited in patents had a downward trend from 686 in 2011 to 57 in 2020. RSC Advances journal was the first top journal to publish these papers. Of 27 subject areas, engineering (24.1%) was the first popular subject that patents cite in their publications. The cluster analysis of keywords identified 8 clusters, including “x-ray diffraction,” “animal,” “adult,” “escherichia coli,” “tissue engineering,” “coronavirus infection,” “neural network,” and “methane.” The technological impact of Iranian research has declined in recent years. It is suggested that research policymakers should consider scholarly outputs that have been cited in patents, which, in a way, shows the flow of knowledge to the industry and encourages researchers to produce such papers.

Abstract Soot stain from diverse sources is the most common stain that stains historical paper documents found in libraries, museums, and storage facilities. It is believed to be one of the types of deterioration that arises from the contact between stains and paper sheets. Therefore, in the present work, the effectiveness of the synthesized hybrid nanogel consisting of carbopol and nanoparticles (NPs) of ZnO, TiO2, or Fe3O4, in low and high-viscosity forms, for eliminating soot stains from historical paper manuscripts was conducted. The prepared hybrid nanogels were characterized utilizing the TEM, AFM, XRD, DLS, and Zeta Potential techniques. Following preparation, the soot-stained paper samples were heated to 105 °C for 6 days, a process known as accelerated thermal aging. Surface morphology, mechanical properties and the color change of the paper samples were investigated. The prepared hybrid nanogel had a spherical shape with well-defined edges and uniform size, with an average particle diameter ranging from 30 to 35 nm. There was no significant NPs agglomeration seen, suggesting uniform dispersion in the carbopol matrix. Additionally, the prepared gels' crystal structure and phase purity were revealed by the XRD analysis results. Paper fibers were visible in some parts of the treated sample with TiO2/carbopol hybrid nanogel at high-viscosity before aging. Cleaning soot-stained paper samples using high-viscosity Fe3O4/carbopol hybrid nanogel is more successful than using low-viscosity nanogel. the sample treated with high-viscosity ZnONPs/carbopol hybrid nanogel produced the highest total color differences (ΔE) (26.17). The paper sample treated with high-viscosity ZnO/carbopol hybrid nanogel exhibited the maximum tensile strength (61.8 N/mm2) and elongation at break (1.174%). The evaluation of the paper samples both before and after the cleaning process revealed that, the treatment with high-viscosity ZnO/carbopol hybrid nanogel gave the best results in removing soot stains from stained paper samples.

To improve the surface properties of low-density wood, poplar wood was functionalized by laminating Al2O3 impregnated paper onto poplar wood (Populus tomentosa Carr.) via unilateral surface compression. Bonding strength between Al2O3 impregnated paper and wood reached up to 3.08 MPa, meeting commercial grade I requirements for impregnated paper laminated wood flooring. A cross-linked structure between Al2O3 impregnated paper and wood was formed without visible cracks or other defects. Density of the functionalized wood surface increased remarkably and the surface hardness was significantly improved, surpassing that of hardwoods for wood flooring. The functionalized wood surface also exhibited high wear resistance, which reached to the specification for commercial grade I impregnated paper laminated wood flooring. Additionally, the water resistance of the functionalized wood surface was significantly improved through lamination with Al2O3 impregnated paper. The functionalized wood demonstrated high applicability for wood flooring.

Microbially contaminated food can cause serious health hazards and economic losses, therefore sensitive, rapid, and highly specific visual detection is called for. Traditional detection of microorganisms is complex and time-consuming, which cannot meet current testing demands. The emergence of paper-based biosensors provided an effective method for efficient and visual detection of microorganisms, due to its high speed, all-in-one device, low cost, and convenience. This review focused on 5 biomarkers, namely nucleic acids, proteins, lipopolysaccharides, metabolites, and the whole microorganism of microorganisms. Besides, the recognition methods were summed up in 5 forms, including immunological recognition, aptamer recognition, nucleic acid amplification-mediated recognition, DNAzyme recognition and clustered regularly interspaced short palindromic repeats mediated recognition. In addition, we summarized the applications of paper-based biosensors in the detection of microorganisms thoroughly. Through the exploration of different biomarkers, identification methods, and applications, we hope to provide a reference for the development of paper-based biosensors and their application in safeguarding the food chain.

Se describen a los micro-papers como formatos novedosos e incipientes para la difusión del conocimiento científico, tanto en revistas científicas como a través de otros métodos nativos del Internet (repositorios, blogs, etcétera). Planteamos la importancia de la utilización de este formato reducido de comunicación de la ciencia para transmitir ciertos tipos de hallazgos, pues presenta una condensación de la información básica en un documento breve, de fácil lectura y con amplia audiencia, sin perder la calidad propia de los trabajos científicos revisados. Para ello, se realiza un estudio descriptivo de carácter exploratorio por medio de una revisión bibliográfica que ahonda en su uso actual y experiencias previas. Concluimos que su viabilidad para la difusión de contenidos científicos concretos busca la agilidad, sin que ello implique la pérdida de la calidad en la difusión científica.

Nanofibrillated cellulose (NFC) and its combined usage with cationic starch and a cationic copolymer of acrylamide were studied in relation to the properties of paper. Independent pulp treatments using additives separately included 0%, 5%, 10%, and 15% refined long fiber pulp, 3 and 6% NFC, 0.75 and 1.5% cationic starch and 0.07% and 0.15% cationic polyacrylamide and combined treatments. Handsheets were made of the above treatments, and finally their optical and microscopic properties were evaluated. Increasing the NFC content to 6% increased the brightness and yellowness of the white liner by 13% and 21%, respectively. The liner opacity was also reduced by 1%. Additionally, increasing NFC by 6% compared to imported long fibers, the brightness and yellowness of the white liner increased 5.44% and 6.3%, respectively. The liner opacity was also reduced by 1%. A 1.5% cationic starch addition to NFC increased the brightness of the white liner by 4.4%, its whiteness increased 1.5%, and its yellowness increased 2.1%. The opacity of the liner was also reduced by 7.1%. The use of NFC and cationic starch can improve the optical properties of the white liner, while imported long fibers may be problematic.

Abstract Gels prepared from the polysaccharide gellan are used for aqueous poulticing treatments in paper conservation when the application of water must be restricted. Optimal use of the rigid, yet shapeable gel requires direct contact with the paper surface, which carries the risk of gel residues on the treated surface. We used acid methanolysis as a destructive analytical method to detect rhamnose as a component of gellan, which was undetectable with ATR-FTIR spectroscopy. We show that there is a significant probability of leaving gellan residues on the paper. Conservators should be aware of this potential side effect when considering the use of gellan poultices in direct contact with paper objects.

Size presses on paper machines are used to apply a solution of a polymer – usually starch – to the surface of the sheet and thereby to increase the stiffness, surface strength, and printing quality of the product. This article reviews publications dealing with the size press equipment, the materials, and factors affecting both the operating efficiency and attributes of the resulting paper. The emergence of film-press equipment (e.g. blade-metering size presses) in the 1980s has greatly decreased the frequency of web breaks and increased productivity. Starch technology at the size press, though relatively mature, continues to evolve. By adjustment of starch attributes, solids levels, and incorporating other additives, modern papermakers can tune size press outcomes to meet a range of paper product requirements, including strength, hydrophobicity, and the reduction of air permeability. By application of various synthetic polymers, mineral particles, and even nanocellulose in combination with starch or other base polymers, there is potential to extend the technology to meet a range of future needs for paper products.

In the field of paper conservation and archival research, identifying the raw materials of paper is important to elucidate its history and culture. As the most basic element of the raw materials for paper, fibers have not been sufficiently investigated. In this study, we propose a nondestructive method for estimating paper fibers from macro photographs ( $4000\times3000$ pixels) captured using a digital camera. The proposed method consists of background patch (500 pixels per side) detection (BPD), wherein background regions with no text are identified; patch fiber classification (PFC), wherein background patches obtained after BPD are analyzed for fiber classification; and paper fiber estimation (PFE), wherein macro images obtained after PFC are analyzed for fiber estimation. BPD and PFC are employed to perform patch-based classification on segmented macro images, which are reconstructed during PFE to obtain the final fiber estimation results. We performed experiments using 1337 macro images (64176 patches) to evaluate the fiber estimation accuracy for kozo, mitsumata, and gampi via three-fold cross-validation. The average fiber classification accuracy for patch images was observed to be 79.1%; accordingly, the average fiber estimation accuracy for macro images was 85.8%. Experimental results indicated that PFE can be realized in a nondestructive manner on macro images of paper captured using a digital camera.

Impinging air jets can be used to dewater, heat, and dry the web of tissue paper. High velocities of the air jets degrade the paper, and appropriate adjustments to the jet velocity and the distance of the nozzle from the surface of the wet web are crucial to obtain the highest quality product. This work investigated the correlation between the velocity of the air jet and the strength of paper subjected to the impingement method. Papers with an initial moisture content of 20% and various pulp mixes were tested, and the physical properties of papers were explored. After impinging an air jet, different tensile strength limits were obtained in the machine and cross directions. The paper had lower apparent density and higher roughness compared to classical pressing. The dependence of tensile strength and roughness on the fibers composition also was determined. Increasing the amount of eucalyptus fibers in impingement dewatered paper resulted in a decrease in its tensile strength and roughness. The value of elongation before breaking was the highest for softwood papers after the impingement method. The maximum velocity of an air jet that can be used to dewater or dry paper without the risk of damage to the papers was determined.

Abstract Numerous natural dyes were used to dye mediaeval Islamic paper from the tenth to the nineteenth century, using a variety of techniques. The objective of this research is to develop an analytical method using high performance liquid chromatography with diode array detection (HPLC–DAD) to identify natural dyes in forty historical Islamic paper manuscripts from two collections. In addition, novel information was obtained from original treatises containing recipes for dyeing paper and the chronological use of dyes in dyeing mediaeval Islamic paper between the tenth and seventeenth centuries. The results show that thirty-four of the forty manuscripts examined contained dyes. Six natural dyes were detected, including henna, madder, lac, safflower, turmeric, and weld. This is the first study aimed at developing a method for determining various natural dyes in Islamic paper from a wide historical and geographical range in the mediaeval time and to fill significant gaps in the technical and historical knowledge of papermaking.

Industrial production and domestic discharge produce a large amount of oily wastewater, which seriously affects the stability of the ecological environment. Membrane separation technology provides another path to treating oily wastewater. And appropriate surface modification of the membrane helps to achieve high efficiency of treating oily wastewater. With green, economy and stability been more concerned. The focal research reports a completely biodegradable all cellulose composite filter paper (ACCFP) composed of I-cellulose macrofibers and II-cellulose matrix. It is a simple one-step impregnation method to adjust the surface microstructure of the pristine filter paper (PFP), and it does not involve with chemical reaction. The pre-wetted ACCFP consist of II-cellulose hydrogel and I-cellulose reinforcement in the process of oil-water separation. This layer of hydrogel is the fundamental to underwater superoleophobicity, which determines their eligibility for applications of efficient oil-water mixture or oil-in-water (oil/water) emulsion separation. The separation efficiency of oil-water mixture and oil/water emulsion exceed 95% and 99.9%, respectively. In addition, excellent mechanical properties of ACCFP in dry and wet conditions ensure its stability in service and prolong service life in applications. The focal study provides a new method for high-performance oil-water separation and it is more in line with sustainable chemistry.

Carbon fibre-reinforced ultra-high temperature ceramics (UHTCs) are considered a class of promising materials for several applications, the most appealing ones being in the aerospace sector. Reinforcement is necessary to overcome the brittleness and low thermal shock resistance of ceramics and is often provided through the addition of carbon fibres or other carbon-based phases, such as nanotubes, graphene, and graphite. The present work is focused on the toughening of UHTCs through incorporation of 30−50 vol% thin, ordered graphite layers from conventional filter paper followed by hot pressing sintering. Cellulose filter paper was selected because it undergoes thermolysis with no melting stage forming a strong carbonaceous residue that can be used as toughener. Microstructure and mechanical properties of toughened composites were compared to those of other materials reinforced with short carbon fibres and the effect of different distribution of graphite was studied. Addition of graphite allowed toughness to be increased from 3−4 MPa·m1/2 (for un-reinforced materials) to 5.1−5.5 MPa·m1/2, similar to results obtained with short fibre reinforcement. The high-temperature properties, such as strength and toughness as well as oxidation resistance at 1500 ℃, were also examined.

Paper pulp is a lignocellulosic fibrous material used in the industrial production of paper and board products. In addition to cellulose and hemicellulose, paper pulp contains 1 to 20% lignin, depending on the raw materials and pulping process used. Lignin is a heterogenous aromatic polymer that is hydrophobic and more resistant to microbial degradation compared to the easily biodegradable cellulose and hemicellulose. In this study, the biodegradation of paper pulps containing varying amounts of lignin was examined in soil and marine environments using ISO testing methods. Lignin significantly reduced the mineralization of paper pulps to CO2 in both environmental conditions, and a strong inverse correlation between lignin content and the mineralization to CO2 was observed. A similar impact was observed with natural materials containing lignin, such as birch sawdust. Since the calculation of biodegradability in most ISO and EN standards is based solely on the concept of mineralization to CO2, materials containing lignin can receive poor values in these tests. The implications of this for standardized requirements of biodegradability and possible options to overcome testing deficiencies are discussed.

Automatic test paper design is critical in education to reduce workloads for educators and facilitate an efficient teaching process. However, current designs fail to satisfy the realistic teaching requirements of educators, including the consideration of both test quality and efficiency. This is the main reason why teachers still manually construct tests in most teaching environments. In this paper, the quality of tests is quantitatively defined while considering multiple objectives, including a flexible coverage of knowledge points, cognitive levels, and question difficulty. Then, a model based on the technique of linear programming is delicately designed to explore the optimal results for this newly defined problem. However, this technique is not efficient enough, which cannot obtain results in polynomial time. With the consideration of both test quality and generation efficiency, this paper proposes a genetic algorithm (GA) based method, named dynamic programming guided genetic algorithm with adaptive selection (DPGA-AS). In this method, a dynamic programming method is proposed in the population initialization part to improve the efficiency of the genetic algorithm. An adaptive selection method for the GA is designed to avoid prematurely falling into the local optimal for better test quality. The question bank used in our experiments is assembled based on college-level calculus questions from well-known textbooks. The experimental results show that the proposed techniques can construct test papers with both high effectiveness and efficiency. The computation time of the test assembly problem is reduced from 3 hours to 2 seconds for a 5000-size question bank as compared to a linear programming model with similar test quality. The test quality of the proposed method is better than the other baselines.

In the era of Industry 4.0, digital transformation has spurred the swift advancement of technologies, including intelligent predictive maintenance scheduling, prognostics and health management. The accurate prediction of remaining useful life plays a crucial role in these technologies as it extends power equipment’s safe operational duration and decreases the maintenance costs associated with unforeseen shutdowns. Also, the increased accessibility of data for monitoring system conditions has paved the way for the more immense adoption of machine learning models in prognostics and health management for power transformers. At the moment, with the ever-increasing demand for electricity, there is a corresponding increase in the degradation processes of power transformers. Transformers insulation system and more importantly, the paper insulation happens to be the principal part where the degradation is prominent. Therefore, an accurate prediction of the insulating paper condition through its degree of polymerization is required to guarantee the reliability of power transformers. In this regard, the predictions, reliability, and health monitoring of this power equipment can be actualized by modeling the degradation of transformer insulation paper through several machine learning frameworks. In this view, this review paper has been drafted not only to serve as a guide for researchers interested in the fields of transformer insulation system fault prognosis but also to offer insights into potential research directions as existing literature in modeling and evaluating transformer paper insulation is presented.

To improve the accuracy and efficiency of the aging life prediction and assessment of transformer oil-paper insulation, and to make up for the deficiencies of traditional characterizers, such as 2-furfural, carbon monoxide, and carbon dioxide, a method for the simultaneous determination of methanol, ethanol, $n-\mathbf{propanol}$, and $n$-butanol in oil with a single injection is established by headspace-gas chromatography-mass spectrometry. The measured results show that the determination limits of the four alcohol characterizers can be controlled to $\mathbf{10}\ \mu \mathbf{g}/\mathbf{kg}$ level. Based on this method, the change patterns of the above four alcohols with thermal aging time and degree of polymerization are obtained through thermal aging experimental research. Ethanol, $n$-propanol, and $n$-butanol in oil indicate nearly linear correlations with thermal aging time and degree of polymerization, similar to that of methanol. By analyzing 52 sets of measured data of 500 kV EHV transformers in operation, $n$-butanol is found to have excellent performance, and a new method to evaluate the aging state of oil-paper insulation employing $n$-butanol and methanol is proposed along with the aging attention value model. The measured data of 500 kV EHV transformers in operation indicate that the combination of $n$-butanol and methanol as the preferred characterizers can effectively compensate for the shortcoming of traditional characterizers in the early stages of aging, and the feasibility of the method is verified. Two possible pathways for the generation of $n$-butanol by cellulose cleavage during the aging of oil-paper are proposed from the chemical structure of cellulose.

The current study is related to fabrication of point-of-care molecularly imprinted paper-based analytical devices, specifically related to ovarian cancer early stage detection. The task involves creating a paper coated with silver nanoparticles (AgNPs) that can be used as a transducer via surface enhanced Raman spectroscopy (SERS) to detect the threshold level of the biomarker lysophosphatidic acid (LPA) as a template molecule to diagnose ovarian cancer. MIPs are synthetic receptors designed for a targeted molecule which are prepared from polymers in the presence of target such as small molecules, proteins or cells etc. Removal of the template results in cavities which are structurally and electrostatically complementary to the template molecule. The molecularly imprinted polymer (MIP) layer was anchored on vinyl trimethoxy silane modified-paper, which served as a detector by hydrolytically modifying the paper surface with vinyl trimethoxy silane. To detect LPA in serum samples for ovarian cancer, MIP-paper based on SERS was developed. Patients with benign ovarian tumors had an LPA level of 7.73 μM whereas those with ovarian cancer have a level of 16.99 μM. A healthy person's LPA level is 2.92 μM. Consequently, the rise in LPA levels may aid in the early detection of ovarian cancer. The study refers to the use of a point of care device to diagnose ovarian cancer early, which should be simple, effective, and cost-effective. The analytical tool in the study is a sensor with high selectivity and sensitivity, quick assay times, and inexpensive costs. For LPA in serum, the binding constant of modified paper-based MIP ranges from 11.00 μM to 0.08 μM. The amalgamation of nanoparticles on 2D-paper with MIP have lead to develop sensor which can effectively select LPA in untreated real samples like serum.

Evaluating the long-term influence of academic papers in the early stage after publication is crucial for research management and decision-making. Although the total number of citations has been considered as a valid indicator to measure the academic influence of papers, there are still some bottleneck problems in predicting future citation counts. Firstly, it remains a challenging task to select the reasonable features due to the diversity of model features. Secondly, some prediction models are overly complex and their defects may cause prediction bias or even errors. Finally, the most important thing is that very few models possess long-term predictive ability. This paper proposes a prediction model that can provide an early evaluation of the long-term citations, or the long-term influence, of academic papers. The model uses features available immediately after publication or after a certain period of time. Taking academic papers in Information Science and Library Science as our experimental subject, we train the model using three machine learning algorithms and find that the artificial neural network performs satisfactorily. Our findings may offer guidance for research management and decision-making.

Extant studies have focused on exploring the research output of universities in Nigeria, but the measure of the quality of research output using citations per paper (CPP) from the Web of Science (WoS) and Scopus is scarcely discussed. This paper investigated the quality of papers published by the top 76 universities in Nigeria. Five hypotheses on CPP were tested using Kruskal-Wallis and Mann-Whitney tests. These hypotheses tested whether CPP is the same or different i) across six geo-political regions (GPRs), ii) between the two major regions, iii) across three university funding types, iv) in Scopus and WoS, and v) if these two databases are correlated. Results using these two databases indicated that no significant median differences were detected among universities across the six GPRs, between northern and southern Nigeria, and between the three funding types (federal, state, and private). Moreover, no significant median differences in CPP between Scopus and WoS were detected, and CPP in both databases was highly positively correlated (0.879; p = 0.05). A comparison of the mean CPP of Nigeria (5.90) from Scopus with 57 other African countries ranked it 47th despite being ranked third in terms of volume of published articles. Policy prescriptions are made on the implications of using CPP for practice.

Poly(3-hydroxybutyrate) (PHB), a biodegradable polymer, has been studied as a substitute for petroleum-based polymers used for barrier coating to improve the barrier and mechanical properties of paper. In this study, ethyl cellulose (EC), a cellulose derivative, was used to prepare a polymer blend for enhancing the barrier properties of PHB. The prepared PHB/EC blend was then applied as a paper coating material. Additionally, the barrier and mechanical properties of the PHB/EC blend-coated paper based on the PHB/EC mixing ratio and coating weight were analyzed. The results showed that the EC could act as a binder for the PHB/EC blend-coated paper. Consequently, the PHB/EC blend-coated paper exhibited significant improvements in mechanical and barrier properties, including a substantial increase of over 100% in internal bond strength, more than 20% in tensile strength, exceeding 60% enhancement in water resistance, and a remarkable increase of over 90% in air permeability.

Herein, the challenge of accurately classifying the manufacturing origin of printing paper, including continent, country, and specific product, was addressed. One-dimensional convolutional neural network (1D CNN) models trained on infrared (IR) spectrum data acquired from printing paper samples were used for the task. The preprocessing of the IR spectra through a second-derivative transformation and the restriction of the spectral range to 1800 to 1200 cm-1 improved the classification performance of the model. The outcomes were highly promising. Models trained on second-derivative IR spectra in the 1800 to 1200-cm-1 range exhibited perfect classification for the manufacturing continent and country, with an impressive F1 score of 0.980 for product classification. Notably, the developed 1D CNN model outperformed traditional machine learning classifiers, such as support vector machines and feed-forward neural networks. In addition, the application of data point attribution enhanced the transparency of the decision-making process of the model, offering insights into the spectral patterns that affect classification. This study makes a considerable contribution to printing paper classification, with potential implications for accurate origin identification in various fields.

The Bündnis Junger Ärztinnen und Ärzte (BJÄ, Alliance of Young Physicians in Germany) has presented a position paper (PP) on Postgraduate Medical Education (PGME) against the background of an unfolding hospital reform in Germany, and they describe existing deficits of PGME in Germany. Based on this, demands were made of legislators, employers and medical associations which could result in a sweeping reformation of PGME. Hospital reforms can only be accomplished with well trained and motivated physicians. In this respect the BJÄ regards the reform of hospitals and the health-care system as a chance for a reform of PGME, which is long overdue. Legislative competence for PGME lies with the States of the Federal Republic of Germany and this warrants an adjustment of state medical association laws to accommodate the demands of the BJÄ. Generally PGME must be taken into consideration in all health-care legislation, in analogy to the meanwhile globally adopted principle of “Health in all Politics (HiAP)”. The BJÄ has made every endeavour to produce this PP. The responsible stakeholders and actors in the health-care system would be well-advised to take the position paper seriously with a dwindling physician work force in hospitals and serious quality deficits in PGME. Hence, the BJÄ must be comprehensively supported. They need congenial partners to define the scientific foundation of all their demands, to test their application under real life conditions in hospital and outpatient care, to pursue research on the impact on patient care and on the intended transformation of the health-care system. This might best be accomplished by partnering with a scientific as has been the case in many countries for decades.

This current study aimed to investigate rural college EFL students’ experiences in dealing with English research paper writing and publication barriers. Five senior EFL students voluntarily participated in a photovoice phenomenological study. The data were collected through two methods, including semi-structured interviews and a photovoice. The students took some emotional photos to express their feeling on paper writing and publication barriers visually. The interviews encouraged them to describe their experiences and feelings through the photos. The data were analyzed by synchronizing each photo with its qualitative description. As for the results, it is noted that there were three main paper writing and publication barriers, including a lack of linguistic competence, being trapped with a journal template, and anxiety towards written corrective feedback. Each interview result was accomplished with emotional photos in several themes such as untidy pieces of paper, scenery, internet search, children’s toys, colourful pens, and empty box. The photos were also supported by qualitative remarks of each EFL student. In short, the photovoice helps to represent deep feelings on the research paper writing and publication barriers experienced by the EFL students.

Antiseptic paper soap is convenient because it is flexible, safe for the skin, easily foams, and relatively affordable. Measuring the ratio between the concentrations of NaOH, cooking oil, citronella oil, and aloe vera additives is needed to improve the quality of antiseptic paper soap. Testing the saponification rate, density, pH, water content, fatty acid (FA) level, and free alkali content is critical to determine the characteristics of antiseptic paper soap so that it meets the standards for solid bath soap according to SNI 3532-2021 which is closest to the characteristics of paper soap because SNI for paper soap is not yet available. The weight ratio of citronella oil to cooking oil used is 1:1, 1:2, and 1:3. The NaOH concentrations used were 30%, 40%, and 50% w/v. The natural additives used are 0%, 5%, and up to 10% of the total mass. The research results showed that saponification value of the antiseptic paper soap produced was 197.724 milligrams KOH/gram up to 206.138 milligrams KOH/gram, the pH of the antiseptic paper soap was 9.1-10.6, the water content value was 10.940%-23.863%, the alkali content value free is 0.044%-0.104%, total fatty acid (FA) content is 29.688%-45.734%. The best antiseptic paper soap is produced using 30% w/v NaOH with a weight ratio of citronella oil to cooking oil used of 1:1 and natural additives (aloe vera) 5% of the total mass.

The results of research on physical and chemical methods for the preliminary treatment of wastewater of a cardboard and paper factory in Khmelnytskyi region of Ukraine are presented. At the cardboard and paper factory, wastewater is treated at a sewage treatment plant, which includes sand traps, primary radial sedimentation tanks, aeration tanks with activated sludge regenerators, secondary radial sedimentation tanks, and bioponds. The use of coagulation and chlorination methods before biological treatment in aeration tanks was proposed. Alumoflock 18% was used as a coagulant, polyacrylamide was used as a flocculant, and sodium hydroxide was used as an alkalizing reagent. The study was conducted on a mixture of industrial and domestic wastewater with COD and BOD5 – 3200 and 1575 mg/dm3, respectively, and on industrial wastewater with COD and BOD5 – 4480 and 1960 mg/dm3, respectively. The effects of reducing COD and BOD5 indicators in the first case after coagulation were 30 and 40%, after chlorination - 37.81 and 43.17%, respectively, in the second after coagulation - 28.57 and 47.24%, respectively. It was established that a significant proportion of organic substances according to the COD indicator is in a dissolved state - 60-70%. It has been proven that as a result of chlorination, the maximum reduction of "pure" COD is achieved, therefore, the possibility and expediency of chlorination of water after the secondary settling tank with increased doses should be considered in the wastewater treatment technology of the cardboard and paper factory.

Due to the high wastepaper recyclability and water-loop system closure, packaging paper mills struggle with increased fines, causing runnability issues. Cellulase enzymes are a preferred treatment choice for the improvement of the pulp refining in stock preparation area but are not widely used or easy to introduce in the production process. Different cellulase enzymes were tested, and those with the highest activity were introduced to the white-water (WW) samples with the aim to reduce fines content as potentially new enzyme applications on the paper machine. The first portion of the study involved the development of an experiment model to find and confirm the optimal enzyme process parameters (40 °C, pH 5.7, reaction time 3 h, and 0.18% v/v enzyme addition) for laboratory made white-water. The second portion of the study included turbidity, colloidal charge, flow cytometry (FCM), and chemical oxygen demand (COD) analysis on industrial and laboratory made white-water samples at optimized process parameters. Obtained results corresponded to reduced fines content in white-water samples, which justified commercial usage of cellulase enzymes on recycled paper machine short loop and potentially increased machine runnability without negative influence on wastewater treatment plant.

In this research, I established an energy benchmark for the pulp and paper industry of Vietnam. I, therefore, focus on three major paper product families, including packaging paper, printing and writing paper, and tissue paper. In this research, I use specific energy consumption (SEC) as the energy performance indicator (EnPI) for computing energy benchmarks for the main sub-sectors in the pulp and paper industry of Vietnam. The factories in the pulp and paper industry of Vietnam are divided into three production scales, and the energy benchmarks are specified by production scales. Energy surveys and energy audits have been used to calculate energy benchmarks. Here, I establish the energy benchmark for the main sub-sectors in the pulp and paper industry of Vietnam according to the three production scales. I also estimate the energy saving potential for the pulp and paper industry of Vietnam based on surveying and auditing results.

Teachers use many methods to measure students' progress in learning Arabic, either by using a computer or manually. This study aimed to determine the level and comparison between student motivation to complete assignments using computer-based and paper-based test methods in Arabic language learning. This research used a quantitative approach with comparative descriptive by performing observation, questionnaire, and interview for data collection. It used data analysis methods, such as validity tests, reliability tests and percentage analysis. The research subjects were 23 tenth graders of Visual Communication Design of SMK Muhammadiyah 2 Malang. The results of this study are: (1) the motivation of students to complete Arabic language assignments by computer-based test methods is 81.13% with high category. (2) The motivation of students to complete Arabic language assignments by paper-based test method is 83.82% with high category. (3) Comparison between the motivation of students to complete assignments using computer and paper-based test methods is 2.7% with low category. This difference is due to several factors, including human resource factors. This research has contributed to the Arabic language learning evaluation as it can be used as a teacher's consideration on what methods to use.

Abstract Some ancient Chinese paper artifacts dyed with amur cork tree bark extracts are currently preserved to different extents in museums and libraries worldwide. As traditional natural plant dyes, the long-term performance of the amur cork tree bark extract-dyed handmade paper has been questioned under a preserved environment. The photodegradation process of the extract-dyed papers was examined under accelerating artificial UVA irradiation conditions according to China national standard-paper and board- accelerated aging (exposure to light). Changes during aging were analyzed by optical observation and scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectrometry (FTIR), pH, and tensile strength and folding endurance tests. The results showed that the main components from extracted dyes played an important role in affecting the photodegradation properties of dyed paper. The changes in surface color, pH, morphology and mechanical properties after the artificial UVA accelerated degradation tests revealed that a suitable concentration of the extract dyes for maintaining the long-term irradiation stability of the paper is important.

It is more important to improve and complete the wastewater process in order to reuse and return it to the production line. In this study, the hydrogen peroxide/ozone process (Peroxone) was investigated as a supplementary step in paper mill wastewater treatment to reduce the amount of chemical oxygen demand and remove E. coli. In this regard, using the Box-Behnken Design method based on the response surface method to optimize and investigate the effect of three variables governing the ozonation process, including the amount of hydrogen peroxide consumed (ml), the amount of ozone input (mg/min) and ozonation time (min) were used. The results showed that the amount of ozone and hydrogen peroxide had the greatest effect for reducing COD (up to about 75%). Also, all three variables have played a significant role in increasing the efficiency of the Peroxone process and even completely eliminating E. coli. In determining the optimal conditions, the amount of ozone (146 mg/min), the amount of hydrogen peroxide (2ml) and the duration of ozonation (23 min), the lowest amount of residual COD (73 mg/L) and the highest efficiency (75% removal of E. coli) are predicted. The results showed that due to the interaction of ozone and hydrogen peroxide, the peroxone process performance was less efficient than the ozonation process alone.

Abstract Background Undergraduate STEM instructors want to help students learn and retain knowledge for their future courses and careers. One promising evidence-based technique that is thought to increase long-term memory is spaced retrieval practice, or repeated testing over time. The beneficial effect of spacing has repeatedly been demonstrated in the laboratory as well as in undergraduate mathematics courses, but its generalizability across diverse STEM courses is unknown. We investigated the effect of spaced retrieval practice in nine introductory STEM courses. Retrieval practice opportunities were embedded in bi-weekly quizzes, either massed on a single quiz or spaced over multiple quizzes. Student performance on practice opportunities and a criterial test at the end of each course were examined as a function of massed or spaced practice. We also conducted a single-paper meta-analysis on criterial test scores to assess the generalizability of the effectiveness of spaced retrieval practice across introductory STEM courses. Results Significant positive effects of spacing on the criterial test were found in only two courses (Calculus I for Engineers and Chemistry for Health Professionals), although small positive effect sizes were observed in two other courses (General Chemistry and Diversity of Life). Meta-analyses revealed a significant spacing effect when all courses were included, but not when calculus was excluded. The generalizability of the spacing effect across STEM courses therefore remains unclear. Conclusions Although we could not clearly determine the generalizability of the benefits of spacing in STEM courses, our findings indicate that spaced retrieval practice could be a low-cost method of improving student performance in at least some STEM courses. More work is needed to determine when, how, and for whom spaced retrieval practice is most beneficial. The effect of spacing in classroom settings may depend on some design features such as the nature of retrieval practice activities (multiple-choice versus short answer) and/or feedback settings, as well as student actions (e.g., whether they look at feedback or study outside of practice opportunities). The evidence is promising, and further pragmatic research is encouraged.

Hemp hurd fiber, a low-value waste stream from the hemp industry, has potential downstream applications as an alternative to non-renewable plastics for single-use food service ware and packaging applications. Packaging paper substrates made from chemically pulped hemp hurd, mixed in varying ratios with bleached thermomechanical radiata pine pulp were developed and tested. Handsheets were characterized using several mechanical property tests including tensile strength, tearing resistance, burst strength, short-span compression, ring crush, together with Gurley air resistance, contact angle, and Cobb60 tests. Generally, addition of hemp hurd fibers significantly improved handsheet mechanical properties. Hot-pressing of the handsheets so as to approximate molded fiber thermoforming further enhanced their performance, with pure hemp hurd handsheets having the highest mechanical properties and barrier performance. A prototype was successfully thermoformed from hemp fiber, demonstrating overall feasibility of this fibre source for molded fibre objects.

Degradation of insulation paper is a key contributor to the failure of power transformers. Insulation degradation accelerates at elevated temperatures, which highlights the potential for better thermal management to prolong life. While several studies have analyzed the benefits of high thermal conductivity oil for reducing temperatures inside a transformer, this study is an initial assessment of the benefits of high thermal conductivity paper on transformer life. Blending particulates with cellulosic fibers offers a pathway for high thermal conductivity paper (with good dielectric properties), which can reduce internal temperatures. Presently, life extensions that can be achieved by the use of such thermally conducting papers were estimated, with the thermal conductivity of the paper being the key parameter under study. The analytical-numerical thermal model used in this study was validated against experimental measurements in a distribution transformer, adding confidence to the utility of the model. This model was then used to provide estimates of hot-spot temperature reduction resulting from the use of papers with higher thermal conductivity than baseline. Transformer life was predicted conventionally by tracking the degree of polymerization of paper over time, based on an Arrhenius model. Results indicate that increasing the thermal conductivity of paper from 0.2 W/mK (baseline) to 1 W/mK reduces the hot spot temperature by 10 °C. While degradation significantly depends on the moisture and oxygen content, the model shows that such a temperature reduction can increase life for all conditions, by as much as a factor of three.

Abstract This study identifies important factors for designing an effective biomimetic paper‐based fog harvesting substrate by examining the harvesting properties of different surfaces, including glass, polyethylene, and superhydrophobic paper. In laboratory‐scale fogging tests, the wetting behavior of the substrates is characterized, and the importance of the tilt angle of the respective surface relative to the fog flow is elaborated. Because successful fog harvesting requires both efficient accumulation of water droplets on the surface (by condensation and collision) and sufficient but not excessive roll‐off of the liquid, the amount of water finally collected is clearly related to the pinning effect, which should prevent the smallest droplets from being carried away by the wind but must not lead to full and permanent wetting of the surface. Coalescence is identified as a major phenomenon to improve droplet roll‐off. In this context, superhydrophobic paper indicates to be a more effective water collector than glass or polyethylene, especially when oriented vertically, since it allows the droplets to roll off very efficiently. Finally, the addition of glass particles to the superhydrophobic coating is proposed as a means of enhancing pinning and improving the fog harvesting efficiency.

The effect of foreign trade on economic growth and development is one of the basics in the scientific literature. The countries' use of their production power on the basis of international trade contributes to economic growth periodically in different ways. Although it varies according to the countries, the manufacturing industry and sub-sectors have a significant impact on foreign trade figures. The relationship between the development achieved by the sectors in international trade and economic growth is important in terms of determining the leading sectors of development. In this study, it is aimed to examine the causality relationship between the growth in the Turkish economy and the foreign trade data of the paper and paper products industry. Export and import growth rates and GDP (economicgrowth) values of the paper and paper products industry are used and cover the 2002-2021 period. According to the results of the Granger causality test applied over the VAR model, there is a one-way causality relationship from exports to economic growth, from economic growth to import, and from export to import.

Abstract Objectives Endoscopic ultrasound‐guided tissue acquisition (EUS‐TA) is used for pathological diagnosis and obtaining samples for molecular testing, facilitating the initiation of targeted therapies in patients with pancreatic cancer. However, samples obtained via EUS‐TA are often insufficient, requiring more efforts to improve sampling adequacy for molecular testing. Therefore, this study investigated the use of oil blotting paper for formalin fixation of samples obtained via EUS‐TA. Methods This prospective study enrolled 42 patients who underwent EUS‐TA for pancreatic cancer between September 2020 and February 2022 at the Osaka International Cancer Institute. After a portion of each sample obtained via EUS‐TA was separated for routine histological evaluation, the residual samples were divided into filter paper and oil blotting paper groups for analysis. Accordingly, filter paper and oil blotting paper were used for the formalin fixation process. The total tissue, nuclear, and cytoplasm areas of each sample were quantitatively evaluated using virtual slides, and the specimen volume and histological diagnosis of each sample were evaluated by an expert pathologist. Results All cases were cytologically diagnosed as adenocarcinoma. The area ratios of the total tissue, nuclear, and cytoplasmic portions were significantly larger in the oil blotting paper group than in the filter paper group. The frequency of cases with large amount of tumor cells was significantly higher in the oil blotting paper group (33.3%) than in the filter paper group (11.9%) (p = 0.035). Conclusions Oil blotting paper can increase the sample volume obtained via EUS‐TA on glass slides and improve sampling adequacy for molecular testing.

Developing land use strategies to optimize carbon sinks and improve carbon footprints involves proposing efficient nature-based solutions that industries and businesses can implement while considering financial and legislative constraints. The pulp and paper industry is associated with significant greenhouse gas (GHG) emissions, primarily due to the substantial carbon dioxide (CO2) footprint of its mills. Also, some forestry operations contribute to the release of carbon to the atmosphere in the form of CO2 and methane (CH4). Conversely, this industry could potentially be a significant ally in the fight against climate change by favoring forestry practices that reduce carbon emissions and increase its sequestration, namely, by adding value to industrial by-products (e.g., biosolids) instead of treating them as wastes and landfilling them. Notably, the pulp and paper industry has been seeking alternative uses of its by-products, such as fertilizers to maximize tree growth. In this paper, we identify opportunities and challenges that exist for the pulp and paper industry in regard to recycling industrial by-products to: 1) lower GHG emissions directly at the mill and 2) improve its GHG budget by increasing carbon sequestration in forests and plantations. We illustrate our analyses by describing a case study of a pulp and paper mill in southern Quebec, Canada, that uses its biosolids and other by-products as fertilizers. This case study highlights that this strategy could not only contribute to the reduction of GHGs but could also create added value and improve economic returns of forest operations.

The increase in energy valorization of paper sludge and biomass waste through incineration results in a rise in waste paper fly ash (WPFA), often perceived as hazardous and requiring specific treatment. In this study, natural carbonation technology at a pilot scale was employed to mitigate the hazardous nature of WPFA by enhancing the stabilization of metal and metalloid trace elements (MMTE), particularly barium (Ba) and lead (Pb) leaching. Natural carbonation of WPFA was found to be optimal at a water/solid ratio of 0.3 L/kg under natural temperature and humidity conditions. Batch leaching tests based on thermodynamic equilibrium were used to assess MMTE solubility concerning pH in both non-carbonated and carbonated WPFA at natural pH. After 7 days of natural carbonation, the leaching concentration of Ba and Pb was below the legal limit in France. The concentration of Ba and Pb in carbonated samples decreased by 98.5% and 98%, respectively. Analyses using thermogravimetry, X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy demonstrated the increased formation and quantity of calcite (CaCO3) with longer carbonation times, along with the formation of new minerals as BaCO3 and PbCO3, confirming the immobilization of these elements post-carbonation. The leaching behavior and release potential of carbonated WPFA were further evaluated using the four-stage sequential extraction procedure proposed by the European Commission’s Bureau of Reference (BCR). The speciation of Ba and Pb shifted significantly from the soluble substance (F1) at 17.6% and 14.8%, respectively, to the carbonate fraction (F2) at 0.49% and 0.02% after 90 days of carbonation. The percolation water collected during the carbonation process adheres to discharge standards into the sea.

Conventional techniques for sharing paper documents in teleconferencing tend to introduce two inconsistencies: 1) media inconsistency: a paper document is converted into a digital image on the remote site; 2) space inconsistency: a workspace deliberately inverts the partner’s handwriting to make a document easy to read. In this paper, we present a novel system that eliminates these inconsistencies. The media and space inconsistencies are resolved by reproducing a real paper document on a remote site and allowing a user to handover the paper document to a remote partner across a videoconferencing display. From a series of experiments, we found that reproducing a real paper document contributes to a higher sense of information sharing. We also found that handing over a document enhances a sense of space sharing, regardless of whether the document is digital or paper-based. These findings provide insights into designing systems for sharing paper documents across distances.