Search

Different from the traditional bulk-edge correspondence principle, the discovery of higher-order topological states has generated widespread interest. In a second-order, two-dimensional elastic wave topological insulator, the fluctuation information can be confined to the corners, with the state being topologically protected. In order to better apply topological corner states, this paper designs a two-dimensional elastic plate with adjustable topological corner states by means of piezoelectric control capability. By selectively connecting negative capacitance circuits to piezoelectric sheets on the honeycomb elastic plate, the energy band can be flipped. The topological corner states at the 2{\pi}/3 corner were observed at the boundary of two different topological phase structures in the finite lattice with finite element software. The strong robustness of the topological corner states was verified by setting up defective control groups at the corner. In addition, the topological corner states of this piezoelectric elastic plate are discussed accordingly in terms of their tunability in frequency and position. The piezoelectric elastic plate is expected to provide a reference for the design of elastic wave local control and energy harvesting devices due to its adjustable topological corner states, which facilitate the application of topological corner states in practice., Comment: 9 pages, 8 figures

This paper proposes a new metamaterial structure consisting of a periodically porous elastomer with pore coatings. This design enables us to engender finite deformation by a contactless load. As a case study, we apply thermal load to the pore coating and carry out a finite element analysis to probe instabilities and the associated phononic properties. It turns out that a novel buckling mode, preserving the nature of surface wrinkling in tubular structures, can be induced under a plane-strain setup, and a smaller size of the unit cell is attained compared to the counterpart of traditional buckled profile in soft porous elastomers. In particular, this buckling pattern is able to produce several bandgaps in different frequency ranges as the macroscopic mean strain increases. We further introduce a metallic core as local resonator, and the updated metamaterial allows a low-frequency bandgap, the bandgap width of which can be estimated by a simplified theoretical model. As more free parameters are involved in the structure, we perform a detailed parametric study to elucidate the influences of the modulus ratio between coating and matrix, the porosity, the core radius, and the macroscopic mean strain on the buckling initiation and the evolution of bandgap. Remarkably, a stiffer surface coating is prone to enhance the stability of the structure, which is contrary to existing results in film/substrate bilayers. It is expected that the current study could shed light on new insight into pattern formation and wave manipulation in porous elastomers., Comment: 16 pages, 19 figures

We study the initiation and evolution of aneurysmal morphology in a pressurized soft tube where the elastic modulus is non-uniform in the radial direction. The primary deformation prior to instability is characterized within the framework of nonlinear elasticity for a general material constitution and a generic modulus gradient. To unravel the influence of modulus gradient on aneurysm formation, we employ the incompressible Gent model and select three representative modulus gradients, including a linear, an exponential, and a sinusoidal function. In particular, the sinusoidal distribution can be used to model actual artery structure. In addition, two prototypical loading conditions are considered, namely, either the resultant axial force or the axial length can be fixed. Based on an explicit bifurcation condition in terms of the internal pressure and the resultant axial force for aneurysm formation or localized bulging, an exhaustive theoretical analysis on bulge initiation is carried out and the effect of geometric and material parameters and modulus gradient on the critical stretch generating localized bulging is revealed. It turns out that the modulus mismatch, as well as the position of maximum modulus, can dramatically affect the onset of localized bulging. Then we analytically elucidate the influence of modulus gradient on bulge propagation and conduct a finite element analysis of bulge evolution based on a robust finite element model established in Abaqus by UHYPER subroutine coding. Interestingly, it is found that a sinusoidally distributed modulus has negligible influence on the critical stretch of bulge initiation, the deformation process of bugle growth, and the maximum size of a bulge. The current analysis can provide useful insight into the biological evolution of human artery and into localized instabilities in graded structures.