Search

The realization of fault-tolerant quantum computing requires the execution of quantum error-correction (QEC) schemes, to mitigate the fragile nature of qubits. In this context, to ensure the success of QEC, a protocol capable of implementing both qubit reset and leakage reduction is highly desirable. We demonstrate such a protocol in an architecture consisting of fixed-frequency transmon qubits pair-wise coupled via tunable couplers -- an architecture that is compatible with the surface code. We use tunable couplers to transfer any undesired qubit excitation to the readout resonator of the qubit, from which this excitation decays into the feedline. In total, the combination of qubit reset, leakage reduction, and coupler reset takes only 83ns to complete. Our reset scheme is fast, unconditional, and achieves fidelities well above 99%, thus enabling fixed-frequency qubit architectures as future implementations of fault-tolerant quantum computers. Our protocol also provides a means to both reduce QEC cycle runtime and improve algorithmic fidelity on quantum computers.

We systematically investigate the influence of the fabrication process on dielectric loss in aluminum-on-silicon superconducting coplanar waveguide resonators with internal quality factors ($Q_i$) of about one million at the single-photon level. These devices are essential components in superconducting quantum processors; they also serve as proxies for understanding the energy loss of superconducting qubits. By systematically varying several fabrication steps, we identify the relative importance of reducing loss at the substrate-metal and the substrate-air interfaces. We find that it is essential to clean the silicon substrate in hydrogen fluoride (HF) prior to aluminum deposition. A post-fabrication removal of the oxides on the surface of the silicon substrate and the aluminum film by immersion in HF further improves the $Q_i$. We observe a small, but noticeable, adverse effect on the loss by omitting either standard cleaning (SC1), pre-deposition heating of the substrate to 300$\deg$C, or in-situ post-deposition oxidation of the film's top surface. We find no improvement due to excessive pumping meant to reach a background pressure below $6{\times} 10^{-8}$ mbar. We correlate the measured loss with microscopic properties of the substrate-metal interface through characterization with X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectroscopy (ToF-SIMS), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), and atomic force microscopy (AFM)., Comment: 22 pages, 11 figures

Quantum processors require a signal-delivery architecture with high addressability (low crosstalk) to ensure high performance already at the scale of dozens of qubits. Signal crosstalk causes inadvertent driving of quantum gates, which will adversely affect quantum-gate fidelities in scaled-up devices. Here, we demonstrate packaged flip-chip superconducting quantum processors with signal-crosstalk performance competitive with those reported in other platforms. For capacitively coupled qubit-drive lines, we find on-resonant crosstalk better than -27 dB (average -37 dB). For inductively coupled magnetic-flux-drive lines, we find less than 0.13 % direct-current flux crosstalk (average 0.05 %). These observed crosstalk levels are adequately small and indicate a decreasing trend with increasing distance, which is promising for further scaling up to larger numbers of qubits. We discuss the implication of our results for the design of a low-crosstalk, on-chip signal delivery architecture, including the influence of a shielding tunnel structure, potential sources of crosstalk, and estimation of crosstalk-induced qubit-gate error in scaled-up quantum processors., Comment: 21 pages, 16 figures, includes appendices, updated discussion on source of xy crosstalk, flux stability, etc

Deducing a 3D human pose from a single 2D image or 2D keypoints is inherently challenging, given the fundamental ambiguity wherein multiple 3D poses can correspond to the same 2D representation. The acquisition of 3D data, while invaluable for resolving pose ambiguity, is expensive and requires an intricate setup, often restricting its applicability to controlled lab environments. We improve performance of monocular human pose estimation models using multiview data for fine-tuning. We propose a novel loss function, multiview consistency, to enable adding additional training data with only 2D supervision. This loss enforces that the inferred 3D pose from one view aligns with the inferred 3D pose from another view under similarity transformations. Our consistency loss substantially improves performance for fine-tuning with no available 3D data. Our experiments demonstrate that two views offset by 90 degrees are enough to obtain good performance, with only marginal improvements by adding more views. Thus, we enable the acquisition of domain-specific data by capturing activities with off-the-shelf cameras, eliminating the need for elaborate calibration procedures. This research introduces new possibilities for domain adaptation in 3D pose estimation, providing a practical and cost-effective solution to customize models for specific applications. The used dataset, featuring additional views, will be made publicly available.

This study introduces silicon substrates with a switchable magnetic contrast layer (MCL) for polarised neutron reflectometry experiments (PNR) at solid/liquid interface to study soft matter surface layers. The advantage with neutron reflectometry (NR) data is that structural and compositional information can be enhanced by using different isotopic contrast on the same sample. This approach is normally referred to as contrast matching, which can be achieved by using solvents with different isotopic contrast, e. g. different H2O/D2O ratio, and/or by selective deuteration of the molecules. However, some soft matter system might be perturbed by this approach, or it might not be possible, particularly for biological samples. In this scenario, solid substrates with a MCL are an appealing alternative, as the magnetic contrast with the substrate can be used to partially recover the information on the sample structure. More specifically, in this study, a magnetically soft Fe layer coated with SiO2 was produced by ion-beam sputter deposition on silicon substrates of different sizes. The structure was evaluated using XRR, AFM, VSM, and PNR. The collected data showed high quality and repeatability of the MCL parameters, regardless of the substrate size and thickness of the capping SiO2 layers. As compared to other kinds of substrates with MCL layer previously proposed, which used Au capping layer, the SiO2 capping layer allows to reproduce the typical surface of standard silicon substrate used for NR experiment and compatible with a large variety of soft matter samples. We demonstrated such application, by using ready-to-measure 50*50*10 mm3 substrates in PNR experiments for the characterisation of a lipid bilayer in a single solvent contrast. Overall, the article highlights the potential of PNR with MCL for investigation of soft matter samples., Comment: 12 pages, 6 figures, 4 tables

In superconducting quantum processors, the predictability of device parameters is of increasing importance as many labs scale up their systems to larger sizes in a 3D-integrated architecture. In particular, the properties of superconducting resonators must be controlled well to ensure high-fidelity multiplexed readout of qubits. Here we present a method, based on conformal mapping techniques, to predict a resonator's parameters directly from its 2D cross-section, without computationally heavy and time-consuming 3D simulation. We demonstrate the method's validity by comparing the calculated resonator frequency and coupling quality factor with those obtained through 3D finite-element-method simulation and by measurement of 15 resonators in a flip-chip-integrated architecture. We achieve a discrepancy of less than 2% between designed and measured frequencies, for 6-GHz resonators. We also propose a design method that reduces the sensitivity of the resonant frequency to variations in the inter-chip spacing., Comment: Accepted version. 13 pages, 12 figures

The Ubiquitous Interactor (UBI) addresses the problems of design and development that arise around services that need to be accessed from many different devices. In UBI, the same service can present itself with different user interfaces on different devices. This is done by separating interaction between users and services from presentation. The interaction is kept the same for all devices, and different presentation information is provided for different devices. This way, tailored user interfaces for many different devices can be created without multiplying development and maintenance work. In this paper we describe the system design of UBI, the system implementation, and two services implemented for the system: a calendar service and a stockbroker service.