58 results on '"Čapek Jiří"'
Search Results
2. The role of the preparation route on microstructure and mechanical properties of AlCoCrFeNi high entropy alloy
3. Residual Stresses and the Microstructure of Modeled Laser-Hardened Railway Axle Seats under Fatigue
4. Influence of Demagnetization and Microstructure Non-Homogeneity on Barkhausen Noise in the High-Strength Low-Alloyed Steel 1100 MC
5. Fatigue of Laser-Welded Structures: Role of Residual Stress
6. Controlled sputter deposition of oxide nanoparticles-based composite thin films
7. Investigation of the size effect on 42CrMo4 + QT steel in the high-cycle fatigue domain part I: Experimental campaign
8. Microstructure and Mechanical Properties of Spark Plasma Sintered CoCrFeNiNbX High-Entropy Alloys with Si Addition
9. Controlled Sputter Deposition of Oxide Nanoparticles-Based Composite Thin Films
10. Effect of the Processing Routes on the Properties of CoCrFeMnNi Alloy
11. Fatigue Properties and Residual Stresses of Laser-Welded Heat-Resistant Pressure Vessel Steel, Verification on Vessel Model
12. Hardening of Rail Vehicle Axles
13. Measurement of the rate of transformation induced plasticity in TRIP steel by the use of Barkhausen noise emission as a function of plastic straining
14. Microstructure and Mechanical Properties of Laser Additive Manufactured H13 Tool Steel
15. Fatigue Damage Analysis On 42CrMo4+QT Via Critical Volume Approach
16. Indentation Size Effect in CoCrFeMnNi HEA Prepared by Various Techniques
17. Erratum: Čapek et al. On the Weldability of Thick P355NL1 Pressure Vessel Steel Plates Using Laser Welding. Materials 2021, 14, 131
18. Tungsten Oxide Based Hydrogen Gas Sensor Prepared by Advanced Magnetron Sputtering
19. Investigation of Magnetic Anisotropy and Barkhausen Noise Asymmetry Resulting from Uniaxial Plastic Deformation of Steel S235
20. Barkhausen Noise Emission in AISI 321 Austenitic Steel Originating from the Strain-Induced Martensite Transformation
21. Nanostructured Materials Based on Thin Films and Nanoclusters for Hydrogen Gas Sensing
22. On the Weldability of Thick P355NL1 Pressure Vessel Steel Plates Using Laser Welding
23. Plasma parameters in positive voltage pulses of bipolar HiPIMS discharge determined by Langmuir probe with a sub-microsecond time resolution
24. Nanostructured CuWO4/WO3- films prepared by reactive magnetron sputtering for hydrogen sensing
25. MECHANICAL PROPERTIES OF FORGED TUNGSTEN HEAVY ALLOYS
26. Ion energy distributions at substrate in bipolar HiPIMS: effect of positive pulse delay, length and amplitude
27. Influence of homogenization on the microstructure, mechanical properties and texture of the twin-roll cast AA8006 sheet processed by accumulative roll-bonding
28. Evaluation of Residual Stresses in Laser Welded High-Pressure Vessels Steels by X-Ray Diffraction
29. Effect of energetic particles on pulsed magnetron sputtering of hard nanocrystalline MBCN (M = Ti, Zr, Hf) films with high electrical conductivity
30. Effect of annealing on structure and properties of Ta–O–N films prepared by high power impulse magnetron sputtering
31. Surface Integrity after Turning a Duplex Stainless Steel with Respect to Tool Geometry
32. Barkhausen Noise Emission in Hard-Milled Surfaces
33. Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials
34. Non-Destructive Evaluation of Steel Surfaces after Severe Plastic Deformation via the Barkhausen Noise Technique
35. Hydrogen gas sensing properties of WO3 sputter-deposited thin films enhanced by on-top deposited CuO nanoclusters
36. Ion-flux characteristics during low-temperature (300 °C) deposition of thermochromic VO2 films using controlled reactive HiPIMS
37. Influence of Tool Wear on Surface State after Turning Stainless Steels
38. Some Aspects of Surface Integrity after Hard Milling
39. INVESTIGATION OF SURFACE MACROSCOPIC RESIDUAL STRESSES OF CUTTING CERAMICS AFTER MECHANICAL MACHINING
40. EFFECT OF ANNEALING ON THE REAL STRUCTURE AND MICROSTRUCTURE OF ADVANCED LASER PROCESSED AISI H13 TOOL STEEL
41. REAL STRUCTURE AND RESIDUAL STRESSES IN ADVANCED WELDS DETERMINED BY X-RAY AND NEUTRON DIFFRACTION
42. COMPARISON OF PARAMETERS OF SURFACE INTEGRITY OF MACHINED DUPLEX AND AUSTENITE STAINLESS STEELS IN RELATION TO TOOL GEOMETRY
43. INFLUENCE OF MACHINING TECHNOLOGIES ON VALUES OF RESIDUAL STRESSES OF OXIDE CUTTING CERAMICS
44. Return of target material ions leads to a reduced hysteresis in reactive high power impulse magnetron sputtering: Model
45. Return of target material ions leads to a reduced hysteresis in reactive high power impulse magnetron sputtering: Experiment
46. X-ray diffraction study of residual stress distribution on surface of laser welded steel sheets
47. Tool Geometry Influence on Surface Integrity of Machined Austenite Stainless Steel
48. Grinding of Inconel 713 Superalloy for Gas Turbines
49. X-Ray Diffraction and Barkhausen Noise Diagnostics of Thick Welds Prepared by Metal Active Gas and Laser Welding
50. Barkhausen Noise Emission in Case - Hardened Bearing Steels
Catalog
Books, media, physical & digital resources
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.