Search

One method to augment rotator cuff repair is to pass dermal allograft pledgets along the sutures that bridge from the medial to the lateral row. It remains unclear whether this augmentation method alters repair biomechanics. This was a controlled laboratory study. After an a priori power analysis, 9 pairs of rotator cuffs underwent double-row suture bridge rotator cuff repair, half randomized to augmentation with dermal allograft pledgets passed along the suture bridge sutures. Repairs were then mounted on a material testing system and loaded cyclically 500 cycles to measure applied force and displacement. Repairs then underwent ultimate failure testing, and stiffness, ultimate failure force, and ultimate failure displacement were measured. Paired t tests were performed to compare between groups. There were no differences between groups in construct gapping with cyclic loading after 500 cycles (P =.885). There were no differences between the augmented and control groups in yield force (103.5 ± 5.0 vs. 101.4 ± 5.9 N, respectively, P =.183), stiffness (94.2 ± 13.9 vs. 90.9 ± 13.8, P =.585), or ultimate failure force (255.3 ± 65.8 vs. 285.3 ± 83.2, P =.315). There were no differences between groups in failure modes, with most specimens failing by cuff tissue tearing within or medial to the construct. The addition of dermal allograft pledgets does not positively or negatively influence the time-zero biomechanical characteristics of double-row suture bridge rotator cuff repair. [ABSTRACT FROM AUTHOR]

Both inlay and onlay humeral implants are available for reverse total shoulder arthroplasty (rTSA), but biomechanical data comparing these components remain limited. This study investigated the effects of inlay and onlay rTSA humeral components on shoulder biomechanics using a biorobotic shoulder simulator. Twenty fresh-frozen cadaveric shoulders were tested before and after rTSA with either an inlay or onlay humeral implant. Comparisons were performed between the most commonly implanted configurations for each implant (baseline) and with a modification to provide equivalent neck-shaft angles (NSAs) for the inlay and onlay configurations. Specimens underwent passive range-of-motion (ROM) assessment with the scapula held static, and scapular-plane abduction was performed, driven by previously collected human-subject scapulothoracic and glenohumeral kinematics. Passive ROM glenohumeral joint angles were compared using t tests, whereas muscle force and excursion data during scapular-plane elevation were evaluated with statistical parametric mapping and t tests. Maximum passive elevation was reduced for the inlay vs. onlay humeral components, although both implants caused reduced passive elevation vs. the native joint. Inlay rTSA also demonstrated reduced passive internal rotation at rest and increased external rotation at 90° of humerothoracic elevation vs. the native joint. All preoperative planning estimates of ROM differed from experiments. Rotator cuff forces were elevated with an onlay vs. inlay humeral implant, but simulated muscle excursions did not differ between systems. Compared with the native joint, rotator cuff forces were increased for both inlay and onlay implants and deltoid forces were reduced for inlay implants. Muscle excursions were dramatically altered by rTSA vs. the native joint. Comparisons of inlay and onlay humeral implants with equivalent NSAs were consistent with the baseline comparisons. Rotator cuff forces required to perform scapular-plane abduction increase following rTSA using both inlay and onlay implants. Rotator cuff forces are lower with inlay implants compared with onlay implants, although inlay implants also result in reduced passive-elevation ROM. Deltoid forces are lower with inlay implants in comparison to the native joint but not with onlay implants. The differences between inlay and onlay components are largely unaffected by NSA, indicating that these differences are inherent to the inlay and onlay designs. In those patients with an intact rotator cuff, decreased rotator cuff forces to perform abduction with an inlay humeral implant compared with an onlay implant may promote improved long-term outcomes owing to reduced deltoid muscle fatigue when using an inlay implant. [ABSTRACT FROM AUTHOR]

Operative treatment of scapulothoracic bursitis most commonly comprises arthroscopic scapulothoracic bursectomy with or without partial superomedial angle scapuloplasty. There is currently no consensus regarding whether or when scapuloplasty should be performed. Prior studies are limited to small case series, and optimal surgical indications are not yet established. The purposes of this study were (1) to retrospectively review patient-reported outcomes of arthroscopic treatment of scapulothoracic bursitis and (2) to compare outcomes between scapulothoracic bursectomy alone and bursectomy with scapuloplasty. We hypothesized that bursectomy with scapuloplasty would provide superior pain relief and functional improvement. All cases of scapulothoracic débridement with or without scapuloplasty completed at a single academic center from 2007 through August 2020 were reviewed. Patient demographic characteristics, symptomatology data, physical examination findings, and corticosteroid injection response data were collected from the electronic medical record. Visual analog scale pain, American Shoulder and Elbow Surgeons, Simple Shoulder Test, and Single Assessment Numeric Evaluation scores were collected. Comparisons between the group undergoing bursectomy alone and the group undergoing bursectomy with scapuloplasty were made using the Student t test for continuous variables and the Fisher exact test for categorical variables. Thirty patients underwent scapulothoracic bursectomy alone, and 38 patients underwent bursectomy with scapuloplasty. Final follow-up data were available for 56 of 68 cases (82%). Final postoperative visual analog scale pain scores (3.4 ± 2.2 and 2.8 ± 2.2, respectively; P =.351), American Shoulder and Elbow Surgeons scores (75.8 ± 17.7 and 76.5 ± 22.5, respectively; P =.895), and Simple Shoulder Test scores (8.8 ± 2.3 and 9.5 ± 2.8, respectively; P =.340) were similar between the bursectomy-alone and bursectomy-with-scapuloplasty groups. Both arthroscopic scapulothoracic bursectomy alone and bursectomy with scapuloplasty are effective treatments for scapulothoracic bursitis. Operative time is shorter without scapuloplasty. In this retrospective series, these procedures showed similar outcomes regarding shoulder function, pain, surgical complications, and rates of subsequent shoulder surgery. Further studies with a focus on 3-dimensional scapular morphology may help optimize patient selection for each of these procedures. [ABSTRACT FROM AUTHOR]

The glenoid labrum acts as a bumper, deepening glenoid concavity and amplifying the concavity-compression mechanism, and serves as the scapular attachment for glenohumeral ligaments. The role of the posterosuperior labrum in anteroinferior glenohumeral stability, and the role of the anterior labrum in posterior stability has been debated. The purpose of this study was to quantify the contribution of anteroinferior and posterosuperior labral tears to loss of glenohumeral stability in multiple directions. Fourteen fresh-frozen cadaveric shoulders were tested on a custom stability ratio measurement apparatus. The peak force that was required to translate the humeral head in anterior, anteroinferior, posterior, and posteroinferior directions was measured under 5 conditions: intact labrum (n = 14), anteroinferior labral tear (n = 7), posterosuperior labral tear (n = 7), combined labral tear (n = 14), and no labrum (n = 14). The stability ratio was defined as the peak translational force divided by the compressive force. Within force-translation curves, we defined the suction cup effect as the force required to release the negative pressure created by an intact labrum. The suction cup effect was usually present with the intact labrum and always disappeared after removal of the labrum for anterior (100% vs. 0%) and posterior (86% vs. 0%) translations (P <.001). After creation of an anteroinferior labral tear, the stability ratio for posterior direction decreased (P <.001) and the suction cup effect disappeared (P <.001). After creation of a posterosuperior labral tear, stability ratios in the anterior and anteroinferior directions decreased (P ≤.006) and the suction cup effect disappeared (P ≤.015). The stability ratio for anterior and anteroinferior testing was more diminished by posterosuperior labral tears than anteroinferior labral tears, and the stability ratio for posterior testing was more diminished by anteroinferior labral tears than posterosuperior labral tears. Anteroinferior labral tears decreased posterior stability and posterosuperior labral tears decreased anterior and anteroinferior stability, largely because of loss of the suction cup effect. [ABSTRACT FROM AUTHOR]

To compare range of motion (ROM) and patient-reported outcomes (PROs) between a structured home exercise program (HEP) and active, supervised physiotherapy (PT) after primary Reverse total shoulder arthroplasty (RTSA) by performing a multicenter randomized clinical trial. Patients undergoing primary RTSA at 2 centers were randomized to either a HEP group, in which they were given a handout and a rope pulley, or a PT group, in which they were given a standardized prescription. Surgical technique and implants were standardized. At baseline, 6 weeks, 3 months, and 1 year postoperatively, we obtained American Shoulder and Elbow Surgeons scores, Western Ontario Osteoarthritis Scores, visual analogue scale for pain scores, and measured ROM via videotape. On video, ROM was then measured by blinded observers. At all study visits, patients were asked how many days per week they were in PT and how many days a week they completed HEP to determine compliance and crossover. An a priori power analysis suggested 29 patients per group, 56 patients total to detect a difference of 30° in active forward elevation with a power of 0.8 at a 2-sided alpha of 0.05. 89 patients were randomized, 43 to PT, and 46 to HEP. We obtained 1-year PRO follow-up on 83 patients (93%) and ROM follow-up on 73 patients (82%). Nine patients (20%) crossed over from HEP to PT and 2 patients (4%) crossed over from PT to HEP. Complications occurred in 13% of HEP and 17% of PT patients (P =.629). Using mixed models that account for baseline values, there were no significant differences between groups in PROs or ROM at final follow-up. In this 2-center, randomized clinical trial, there were no significant differences in patient outcomes or ROM between HEP and PT after RTSA. These findings suggest that it may not be necessary to recommend PT as a protocol for all patients after RTSA. [ABSTRACT FROM AUTHOR]

Internal rotation in adduction is often limited after reverse total shoulder arthroplasty (rTSA), but the origins of this functional deficit are unclear. Few studies have directly compared individuals who can and cannot perform internal rotation in adduction. Little data on underlying 3D humerothoracic, scapulothoracic, and glenohumeral joint relationships in these patients are available. Individuals >1-year postoperative to rTSA were imaged with biplane fluoroscopy in resting neutral and internal rotation in adduction poses. Subjects could either perform internal rotation in adduction with their hand at T12 or higher (high, N = 7), or below the hip pocket (low, N = 8). Demographics, the American Shoulder and Elbow Surgeons score, Simple Shoulder Test, and scapular notching grade were recorded. Joint orientation angles were derived from model-based markerless tracking of the scapula and humerus relative to the torso. The 3D implant models were aligned to preoperative computed tomography models to evaluate bone-implant impingement. The Simple Shoulder Test was highest in the high group (11 ± 1 vs. 9 ± 2, P =.019). Two subjects per group had scapular notching (grades 1 and 2), and 3 high group and 4 low group subjects had impingement below the glenoid. In the neutral pose, the scapula had 7° more upward rotation in the high group (P =.100), and the low group demonstrated 9° more posterior tilt (P =.017) and 14° more glenohumeral elevation (P =.047). In the internal rotation pose, axial rotation was >45° higher in the high group (P ≤.008) and the low group again had 11° more glenohumeral elevation (P =.058). Large rotational differences within subject groups arose from a combination of differences in the resting neutral and maximum internal rotation in adduction poses, not only the terminal arm position. Individuals who were able to perform high internal rotation in adduction after rTSA demonstrated differences in joint orientation and anatomic biases versus patients with low internal rotation. The high rotation group had 7° more resting scapular upward rotation and used a 15°-30° change in scapular tilt to perform internal rotation in adduction versus patients in the low group. The combination of altered resting scapular posture and restricted scapulothoracic range of motion could prohibit glenohumeral rotation required to reach internal rotation in adduction. In addition, inter-patient variation in humeral torsion may contribute substantially to postoperative internal rotation differences. These data point toward modifiable implant design and placement factors, as well as foci for physical therapy to strengthen and mobilize the scapula and glenohumeral joint in response to rTSA surgery. [ABSTRACT FROM AUTHOR]

The etiology of adhesive capsulitis involves inflammation, thickening, and fibrosis of the shoulder capsule. The underlying genetic factors are poorly understood. The purpose of this study was to identify genetic variants associated with adhesive capsulitis using the UK Biobank (UKB) cohort and compare them with variants associated with Dupuytren disease investigating a common etiology between the 2 fibrotic disorders. A genome-wide association study (GWAS) was performed using data from UKB with 10,773 cases of adhesive capsulitis, and a second GWAS was performed with 8891 cases of Dupuytren disease. Next, a comparison of association statistics was performed between adhesive capsulitis and Dupuytren disease using the data from both GWAS. Finally, single-nucleotide polymorphisms (SNPs) previously reported from candidate gene studies for adhesive capsulitis and Dupuytren disease were tested for association with adhesive capsulitis and Dupuytren disease using the summary statistics from their respective GWAS. The UKB GWAS for adhesive capsulitis identified 6 loci that reached genome-wide statistical significance: a cluster of 11 closely linked SNPs on chromosome 1; a single SNP on chromosome 2; a single SNP on chromosome 14; 2 closely linked SNPs on chromosome 21; 33 closely linked SNPs on chromosome 22; and 3 closely linked SNPs on the X chromosome. These SNPs were associated with 8 different genes including TSPAN2/NGF , SATB2 , MRPL52/MMP14 , ERG , WNT7B , and FGF13. A GWAS for Dupuytren disease was performed and a comparison to the adhesive capsulitis GWAS showed 13 loci significantly associated with both phenotypes. A validation attempt of 6 previously reported SNPs associated with adhesive capsulitis using UKB summary statistics was unable to confirm any of the previously reported SNPs (all P >.19). All 23 previously reported SNPs associated with Dupuytren disease were confirmed using the UKB summary statistics (P < 2.1 × 10−3) This GWAS investigating adhesive capsulitis has identified 6 novel loci involving 8 different genes to be associated with adhesive capsulitis. A GWAS investigating Dupuytren disease was performed and compared to the adhesive capsulitis GWAS, and 13 common loci were identified between the 2 disorders with genes involved in pathologic fibrosis. We were unable to validate the SNPs in candidate genes previously reported to be associated with adhesive capsulitis although we were able to confirm all previously reported SNPs associated with Dupuytren disease. The strong genetic overlap between the adhesive capsulitis and Dupuytren disease loci suggests a similar etiology between the 2 diseases. [ABSTRACT FROM AUTHOR]

Although muscle weakness and/or imbalance of the rotator cuff are thought to contribute to the development of shoulder instability, the association between muscular dysfunction and shoulder instability is not completely understood. The purpose of this study was to evaluate rotator cuff and deltoid muscle cross-sectional areas in different types of shoulder instability (anterior, posterior, and multidirectional instability [MDI]) and to determine the associations between muscular imbalance and shoulder instability direction. Preoperative magnetic resonance images of patients with shoulder instability who subsequently underwent arthroscopic glenohumeral labral repair or capsular plication were evaluated. Shoulder instability was classified into 3 categories by direction: (1) anterior, (2) posterior, and (3) MDI. The rotator cuff (supraspinatus, subscapularis, and infraspinatus + teres minor) and deltoid (anterior and posterior portions, and total) muscle areas were measured on T1 sagittal and axial slices, respectively. The ratios of the subscapularis to infraspinatus + teres minor area and the anterior deltoid to posterior deltoid area were calculated to quantify the transverse force couple imbalance. A total of 189 patients were included, where each group consisted of 63 patients. The infraspinatus + teres minor muscle area was smaller than the subscapularis muscle area in the anterior instability group (P =.007). The subscapularis muscle area was smaller than the infraspinatus + teres minor muscle area in the posterior instability and MDI groups (P ≤.003). The anterior deltoid muscle area was smaller than the posterior deltoid muscle area in all groups (P ≤.001). The subscapularis–to–infraspinatus + teres minor area ratio in the anterior instability group (1.18 ± 0.40) was higher than that in the posterior instability and MDI groups (0.79 ± 0.31 and 0.93 ± 0.33, respectively; P <.001). There was no difference in the anterior deltoid–to–posterior deltoid area ratio among the 3 groups. Patients with anterior instability have smaller muscle area of the posterior rotator cuff as compared with the anterior rotator cuff. In contrast, patients with posterior instability and MDI have smaller muscle area of the anterior rotator cuff as compared with the posterior rotator cuff. Thus, the direction of shoulder instability is associated with rotator cuff muscle area. [ABSTRACT FROM AUTHOR]

Optimal implant placement in reverse total shoulder arthroplasty (rTSA) remains controversial. Specifically, the optimal glenoid inclination is unknown. Therefore, a cadaveric shoulder simulator with 3-dimentional human motion specific to rTSA was used to study joint contact and muscle forces as a function of glenoid component inclination. Eight human cadaver shoulders were tested before and after rTSA implantation. Scapular plane abduction kinematics from control subjects and those with rTSA drove a cadaveric shoulder simulator with 3-dimentional scapulothoracic and glenohumeral motion. Glenoid inclination varied from −20° to +20°. Outputs included compression, superior-inferior (S/I) shear, and anterior-posterior shear forces from a 6° of freedom load cell in the joint, and deltoid and rotator cuff muscle forces. Data were evaluated with statistical parametric mapping and t -tests. Inferior glenoid inclination (−) reduced S/I shear by up to 125% relative to superior inclination, with similar compression to the neutral condition (0°). Superior inclinations (+) increased the S/I shear force by approximately the same magnitude, yet decreased compression by 25% in the most superior inclination (+20°). There were few differences in deltoid or rotator cuff forces due to inclination. Only the middle deltoid decreased by approximately 7% for the most inferior inclination (−20°). Compared with native shoulders, the neutral (0°) rTSA inclination showed reduced forces of 30%-75% in the anterior deltoid and a trend toward decreased forces in the middle deltoid. Force demands on the rotator cuff varied as a function of elevation, with a trend toward increased forces in rTSA at peak glenohumeral elevation. Inferior inclination reduces superior shear forces, without influencing compression. Superior inclination increased S/I shear, while decreasing compression, which may be a source of component loosening and joint instability after rTSA. Inferior inclination of the rTSA glenoid may reduce the likelihood of glenoid loosening by reducing the magnitude of cyclic shear and compressive loading during arm elevation activities, although this may be altered by specific-subject body habitus and motion. These factors are especially important in revision rTSA or glenoid bone grafting where there is already a 3-fold increase in glenoid baseplate loosening vs. primary rTSA. [ABSTRACT FROM AUTHOR]

During anatomic total shoulder arthroplasty (aTSA), the humeral head can be resected with or without the use of an intramedullary cutting guide, the former referred to as intramedullary (IM) resection and the latter referred to as freehand (FH) resection. Outcomes following aTSA are predicated upon the restoration of the native humeral anatomy, which can be more challenging with stemless implants. To date, no studies have determined which method of humeral head resection is superior in restoring native anatomy. Our purpose was to determine whether FH or IM resection was superior in restoring native anatomy during aTSA with stemless implants. A review of all patients who underwent aTSA using the stemless Tornier Simpliciti Shoulder System at two academic institutions by two separate surgeons between January 2017 and June 2020 was performed. One surgeon at one institution performed stemless aTSA using the IM resection technique, while the second surgeon utilized the FH resection technique. Patients were excluded if they underwent surgery for an indication other than glenohumeral osteoarthritis, if they received a short-stem or standard-stem implant, or if they lacked adequate preoperative and postoperative Grashey radiographs. One hundred eleven patients across both institutions (51 IM, 60 FH) were included for the final radiographic assessment. The humeral head height (HH) and neck-shaft angle (NSA) were measured on preoperative and postoperative Grashey radiographs. The centers of rotation (CORs) were measured on postoperative Grashey radiographs. Patients were classified as having acceptable restoration of their native anatomy if the change (Δ) in COR or HH was ≤3 mm and ≤ 5 mm, respectively, or if the postoperative NSA was ≥130°. IM resection had the greatest acceptable restoration of COR (90.2% IM versus 70% FH, P =.009), HH (96.1% IM vs. 63.3% FH, P <.001), and NSA (96.1% IM vs. 78.3% FH, P =.006) relative to FH resection. The mean postoperative NSAs for the IM and FH cohorts were 134.4° (±2.1°) and 133.8° (±5.4°), respectively (P =.208). The mean ΔCORs for the IM and FH groups were 1.2 (±1.5) and 2.3 (±1.2) mm, respectively (P <.001). Finally, the mean ΔHHs for the IM and FH cohorts were 1.7 (±1.4) and 4.4 (±2.9) mm, respectively (P <.001). Restoration of the native humeral anatomy following stemless aTSA occurred at a significantly higher rate when using IM vs. FH resection. [ABSTRACT FROM AUTHOR]

Although typically favorable in outcome, anatomic total shoulder arthroplasty (aTSA) can require long-term revision. The most common cause for revision is glenoid loosening, which may result from eccentric cyclic forces and joint translations. "Rocking" of the glenoid component may be exacerbated by the joint geometry, such as glenoid inclination and version. Restoration of premorbid glenoid inclination may be preferable, although laboratory and computational models indicate that both superior inclination and inferior inclination have benefits. This discrepancy may arise because previous studies were limited by a lack of physiological conditions to test inclination. Therefore, a cadaveric shoulder simulator with 3-dimensional human motion was used to study joint contact and muscle forces with isolated changes in glenoid inclination. Eight human cadaveric shoulders were tested before and after aTSA. Scapular-plane abduction kinematics from human subjects were used to drive a cadaveric shoulder simulator with 3-dimensional scapulothoracic and glenohumeral motion. Glenoid inclination was varied from −10° to +20°, whereas compressive, superior-inferior shear, and anterior-posterior shear forces were collected with a 6- df load cell during motion. Outputs also included muscle forces of the deltoid and rotator cuff. Data were evaluated with statistical parametric mapping repeated-measures analysis of variance and t tests. Inferior glenoid inclination (−10°) reduced both compressive and superior-inferior shear forces vs. neutral 0° inclination by up to 40%, and even more when compared with superior inclination (P <.001). Superior inclinations (+10° and +20°) tended to increase deltoid and rotator cuff forces vs. neutral 0° inclination or inferior inclination, on the order of 20%-40% (P ≤.045). All force metrics except anterior-posterior shear were lowest for inferior inclination. Most aTSA muscle forces for neutral 0° inclination were not significantly different from native shoulders and decreased 45% and 15% in the posterior deltoid and supraspinatus, respectively (P ≤.003). Joint translations were similar to prior reports in aTSA patients and did not differ between any inclinations or compared with native shoulders. Joint reaction forces were similar to those observed in human subjects with instrumented aTSA implants, providing confidence in the relative magnitude of our results. Inferior inclination reduces overall forces in the shoulder. Superior inclinations increase the muscle effort required for the shoulder to achieve similar motion, thus increasing the forces exerted on the glenoid component. These results suggest that a preference toward aTSA glenoid components in inferior inclination may reduce the likelihood of glenoid loosening by reducing excessive muscle and joint contact forces. [ABSTRACT FROM AUTHOR]

The purpose of the study was to identify genetic variants associated with rotator cuff disease by performing a genome-wide association study (GWAS) for shoulder impingement using the UK Biobank (UKB) cohort and then combining the GWAS data with a prior GWAS for rotator cuff tears. The loci identified by the GWAS and meta-analysis were examined for changes in expression following rotator cuff tearing using RNA sequencing. A GWAS was performed using data from UKB with 3864 cases of shoulder impingement. The summary statistics from shoulder impingement and a prior study on rotator cuff tears were combined in a meta-analysis. Also, the previous association of 2 single-nucleotide polymorphisms (SNPs) with shoulder impingement from a published GWAS using the UKB was tested. Rotator cuff tendon biopsies were obtained from 24 patients with full-thickness rotator cuff tears who underwent arthroscopic rotator cuff repair (cases) and 9 patients who underwent open reduction internal fixation for a proximal humeral fracture (controls). Total RNA was extracted and differential gene expression was measured by RNA sequencing for genes with variants associated with rotator cuff tearing. The shoulder impingement GWAS identified 4 new loci: LOC100506457, LSP1P3, LOC100506207, and MIS18BP1/LINC00871. Combining data with a prior GWAS for rotator cuff tears in a meta-analysis resulted in the identification of an additional 7 loci: SLC39A8/UBE2D3, C5orf63, ASTN2, STK24, FRMPD4, ACOT9/SAT1, and LINC00890/ALG13. Many of the identified loci have known biologic functions or prior associations with diseases, suggesting possible biologic pathways leading to rotator cuff disease. RNA sequencing experiments show that expression of STK24 increases whereas expression of SAT1 and UBE2D3 decreases following rotator cuff tearing. Two SNPs previously reported to show an association with shoulder impingement from a prior UKB GWAS were not validated in our study. This is the first GWAS for shoulder impingement in which new data from UKB enabled the identification of 4 loci showing a genetic association. A meta-analysis with a prior GWAS for rotator cuff tearing identified an additional 7 loci. The known biologic roles of many of the 11 loci suggest plausible biologic mechanisms underlying the etiology of rotator cuff disease. The risk alleles from each of the genetic loci can be used to assess the risk for rotator cuff disease in individual patients, enabling preventative or restorative actions via personalized medicine. [ABSTRACT FROM AUTHOR]

To improve understanding of the pathophysiology of rotator cuff repair and develop therapeutic treatments an animal model is essential. This Technical Note describes a comprehensive step-by-step description of rotator cuff repair in the mouse. This technique is particularly beneficial because the murine rotator cuff is anatomically similar to that of humans. The mouse model can also be used to test the biological role of candidate genes during repair and be used to identify drugs that accelerate the healing process. [Display omitted] [ABSTRACT FROM AUTHOR]

Restoration of muscular strength is predicated on restoration of muscle length. The purpose of this study was to describe infraspinatus and deltoid length preoperative to reverse total shoulder arthroplasty (RTSA) to guide distalization and lateralization to restore preoperative muscle length. This was a retrospective radiographic study. We measured the infraspinatus length on preoperative computed tomographic images and the deltoid length on preoperative radiographs. For all measurements, reliability was first established by comparing measurements between 2 observers, and intraclass correlation coefficients (ICCs) were calculated. We then calculated descriptive statistics for these muscle lengths and developed a formula to predict these muscle lengths from patient demographics. We measured infraspinatus length in 97 patients and deltoid length in 108 patients. Inter-rater reliability was excellent, with all ICCs >0.886. The mean infraspinatus length was 15.5 cm (standard deviation 1.3) and ranged from 12.6-18.9 cm, whereas the deltoid length was 16.2±1.7 cm and ranged from 12.5-20.2 cm. Both infraspinatus (r = 0.775, P <.001) and deltoid length (r = 0.717, P <.001) were highly correlated with patient height but did not differ between diagnoses. Formulae developed through linear regression allowed prediction of muscle length to within 1 cm in 78% and within 2 cm in 100% for the infraspinatus and 60% and 88% for the deltoid. Deltoid and infraspinatus length are variable but highly correlated with patient height. To maintain tension, 2 mm of lateralization and distalization should be added for every 6 inches (∼15 cm) of height above average for a Grammont-style RTSA. [ABSTRACT FROM AUTHOR]

The etiology of rotator cuff tearing is likely multifactorial, including a potential genetic predisposition. The purpose of the study was to identify genetic variants associated with rotator cuff tearing utilizing the UK Biobank (UKB) cohort, confirm variants using a separate genetic database, and evaluate tissue expression of genes with associated variants following rotator cuff tearing using RNA sequencing. Genome-wide association study (GWAS) : A GWAS was performed using data from UKB with 5701 cases of rotator cuff injury. RNA sequencing analyses: rotator cuff biopsies were obtained from 24 patients with full-thickness rotator cuff tears who underwent arthroscopic rotator cuff repair (cases) and 9 patients who underwent open reduction internal fixation for a proximal humerus fracture (controls). Total RNA was extracted and differential gene expression was measured by RNAseq for genes with variants associated with rotator cuff tearing. The results of the UKB GWAS identified 3 loci that reached genome-wide statistical significance: 2 loci on chromosome 7 in GLCCI1 (rs4725069; P = 5.0E–09) and THSD7A (rs575224171; P = 5.3E–09), and 1 locus on chromosome 2 in ZNF804A (rs775583810; P = 3.9E–09). The association with rotator cuff injury of the GLCCI1 single-nucleotide polymorphism (SNP; rs4725069) was confirmed in the Kaiser Permanente Research Bank cohort (P =.008). Twenty previously reported SNPs in 12 genes were evaluated using summary statistics from the UKB GWAS, which confirmed 3 SNPs in TNC with rotator cuff injury (rs1138545, rs72758637, and rs7021589; all P <.0024). Of 17 genes with variants associated with rotator cuff injury (14 previously from literature plus 3 new genes from current UKB GWAS), TIMP2 , Col5A1 , TGFBR1 , and TNC were upregulated (P <.001 for all) and THSD7A was downregulated (P =.005) in tears vs. controls in the RNA sequencing data set. The UKB GWAS has identified 3 novel loci associated with rotator cuff tearing (ZNF804A , GLCCI1 , THSD7A). Expression of the THSD7A gene was significantly downregulated in rotator cuff tears vs. controls supporting a potential functional role. Three previously reported SNPs in the TNC gene were validated in the UKB GWAS, supporting a role for this gene in rotator cuff tearing. Finally, TIMP2 , Col5A1 , TGFBR1 , and TNC genes were found to have significantly upregulated tissue expression in cases vs. controls supporting a biologic role in tearing for these genes. [ABSTRACT FROM AUTHOR]

The purpose of this study was to determine the factors associated with outcomes after reverse total shoulder arthroplasty (RTSA). We retrospectively evaluated all RTSAs performed by the senior author between January 1, 2007, and November 1, 2017. We evaluated pain visual analog scale (VAS), Simple Shoulder Test (SST), and American Shoulder and Elbow Surgeons Standardized Shoulder Assessment Form (ASES) scores and complication and reoperation rates at a minimum of 2-year follow-up. We evaluated preoperative and 2-week postoperative radiographs for glenoid inclination (GI), medialization as distance between the center of the humeral head or glenosphere and the line of the deltoid, and distalization via the acromial–greater tuberosity distance. We performed inter- and intrarater reliabilities via intraclass correlation coefficients (ICCs) and conducted a multivariable analysis. We included 230 RTSAs in the analysis, with 70% follow-up at a median of 3.4 years. Reliability was acceptable with all ICCs >.678. Increased postoperative GI was significantly associated with increased VAS pain postoperatively (P =.008). Increased distalization was associated with an increased rate of complications and reoperations (P =.032). Younger age (P =.008), female gender (P =.009), and lower body mass index (BMI) (P =.006) were associated with worse ASES scores. Female gender (P <.001) and lower BMI (P =.039) were associated with worse SST scores. Female gender (P =.013) and lower BMI (P =.005) were associated with worse VAS-pain scores. Age, gender, and BMI are associated with outcome after RTSA. In this retrospective analysis of a Grammont-style RTSA, superior inclination is associated with increased pain postoperatively, whereas excessive arm lengthening is associated with increased risk for complication or reoperation. [ABSTRACT FROM AUTHOR]

The purposes of this study were to determine whether acromial morphology (1) could be measured accurately on magnetic resonance images (MRIs) as compared to computed tomographs (CTs) as a gold standard, (2) could be measured reliably on MRIs, (3) differed between patients with rotator cuff tears (RCTs) and those without evidence of RCTs or glenohumeral osteoarthritis, and (4) differed between patients with rotator cuff repairs (RCRs) that healed and those that did not. This is a retrospective comparative study. We measured coronal, axial, and sagittal acromial tilt; acromial width, acromial anterior and posterior coverage, and glenoid version and inclination on MRI corrected into the plane of the glenoid. We determined accuracy by comparison with CT via intraclass correlation coefficients (ICCs). To determine reliability, these same measurements were made on MRI by 2 observers and ICCs calculated. We compared these measurements between patients with a full-thickness RCT and patients aged >50 years without evidence of an RCT or glenohumeral osteoarthritis. We then compared these measurements between those patients with healed RCRs and those with a retorn rotator cuff on MRI. In this portion, we only included patients with both a preoperative MRI and a postoperative MRI at least 1 year from RCR. Only those patients without tendon defects on postoperative MRIs were considered to be healed. In these patients, we also radiographically measured the critical shoulder angle. In a validation cohort of 30 patients with MRI and CT, all ICCs were greater than 0.86. In these patients, the inter-rater ICCs of the MRI measurements were >0.53. In our RCT group of 110 patients, there was greater acromial width [mean difference (95% confidence interval) = 0.1 (0, 0.2) mm, P =.012] and significantly less sagittal acromial tilt [9° (5°-12°), P <.001] than in our comparison group of 107 patients. A total of 110 RCRs were included. Postoperative MRI scans were obtained at a mean follow-up of 24.2 ± 15.8 months, showing 84 patients (76%) had healed RCRs. Aside from acromial width, which was 0.2 mm different and thus did not have clinical significance, there was no association between healing and any of the measured morphologic characteristics. Patients with healed repairs had significantly smaller tears in terms of both width (P <.001) and retraction (P <.001). Although the acromion is wider in RCTs, the difference of 0.1 mm likely has no clinical significance. The acromion is more steeply sloped from posteroinferior to anterosuperior in those with RCTs. These findings call into question subacromial impingement due to native acromial morphology as a cause of rotator cuff tearing. Acromial morphology, critical shoulder angle, and glenoid inclination were not associated with healing after RCR. This study does not support lateral acromioplasty. [ABSTRACT FROM AUTHOR]

Minimal clinically important differences (MCIDs) for different patient outcome scores have been reported for various shoulder diseases, including shoulder arthroplasty and the nonoperative treatment of rotator cuff disease. The purpose of this study was to assess the MCID for the American Shoulder and Elbow Surgeons Standardized Shoulder Assessment Form (ASES) score, the Simple Shoulder Test (SST), and a visual analog scale (VAS) measuring pain, after arthroscopic rotator cuff repair. A total of 202 patients who underwent arthroscopic rotator cuff repair were retrospectively reviewed. ASES, SST, and VAS pain scores were collected preoperatively and at 1 year postoperatively. The MCID was then calculated via a 4-question anchor–based method. The MCID results for the ASES, SST, and VAS pain scores were 27.1, 4.3, and 2.4, respectively. Age at time of surgery, sex, anteroposterior tear size, and worker's compensation status were not associated with MCID values (P >.05). The MCID values determined in the current study are higher than those previously identified for the nonoperative treatment of rotator cuff disease using the same anchor questions. Use of these higher values should be considered when evaluating improvements of individual patients after rotator cuff repair, to determine comparative effectiveness of various rotator cuff repair techniques and to determine sample sizes for prospective comparative trials of rotator cuff repair methods. [ABSTRACT FROM AUTHOR]

Large glenoid defects present a challenge during primary and revision reverse total shoulder arthroplasty (RTSA) especially when humeral head autograft is not available as a bone graft source. The purpose of this study was to evaluate the clinical and radiographic outcomes of RTSA with concomitant structural allografting to reconstruct large glenoid defects. From May 2008 to July 2016, 22 patients underwent primary or revision RTSA with structural glenoid allografting. Of 22 patients, 19 (86%) were available for a minimum 2-year clinical follow-up (average, 2.8 ± 1.3 years), and 17 of 22 (77%) were available for a minimum 1-year radiographic follow-up. Functional outcomes, range of motion, radiographic deformity correction, allograft incorporation, and complication rates were determined. From preoperatively to postoperatively, significant improvements in the average Simple Shoulder Test score (2 ± 2 preoperatively vs. 10 ± 8 postoperatively, P =.002), the average American Shoulder and Elbow Surgeons score (31 ± 19 preoperatively vs. 70 ± 25 postoperatively, P <.001), and average active forward elevation (71° ± 41° preoperatively vs. 128° ± 28° postoperatively, P <.001) were noted. Coronal-plane radiographic correction was 29° ± 12° as measured with the reverse shoulder arthroplasty angle (P <.001) and 14° ± 11° as measured with the β angle (P <.001). Postoperatively, of 17 patients with a minimum 1-year radiographic follow-up, 14 (82%) had complete radiographic incorporation of the graft. Acromial fracture nonunions developed in 2 patients and loosening and migration of the baseplate were found in 2 patients, although no patients elected to undergo further surgery. RTSA with allograft reconstruction of severe glenoid defects allows restoration of glenoid anatomy and leads to high rates of bony incorporation with low rates of glenoid loosening or requirement for revision. Structural allograft is an excellent alternative to autograft in revision RTSA to avoid graft-site morbidity. [ABSTRACT FROM AUTHOR]

Purpose: To determine, in the context of measuring bone loss in shoulder instability, whether measurement differences between magnetic resonance imaging (MRI) and computed tomography (CT), linear-based and area-based methods, and observers altered the proposed treatment when a standardized algorithm was applied.Methods: This was a retrospective, comparative imaging study of preoperative patients with anterior shoulder instability with both an MRI and CT scan within 1 year of one another. On parasagittal images reoriented en face to the glenoid, 2 attending orthopaedic surgeons measured glenoid width, glenoid area, glenoid defect width, and glenoid defect area. On axial images maximal Hill-Sachs width was measured. From these, linear percent glenoid bone loss (%GBL) and area %GBL were calculated, and on-versus off-track was determined. With these results, a recommended treatment was determined by applying a standardized algorithm, in which the Latarjet procedure was selected for %GBL >20%, arthroscopic labral repair and remplissage for off-track lesions with %GBL <20%, and arthroscopic labral repair on-track shoulders with %GBL <20%.Results: In total, 53 patients with mean ± standard deviation 45 ± 83 days between scans were include with a CT linear %GBL of 23.5 ± 9.6% (range 0%-47%). CT lead to larger measurements of %GBL than MRI (linear P = .008, area P = .003), and fewer shoulders being considered on-track (33.0% vs 40.5%), which would alter treatment in 25% to 34%. Linear measurements produced larger values for %GBL (CT, P < .001; MRI, P < .001), which would alter treatment in 25%. For %GBL, inter-rater reliability was good, with intraclass correlation coefficients varying from 0.727 to 0.832 and Kappa varying from 0.57 to 0.62, but these inter-rater differences would alter treatment in 31%.Conclusions: The significant differences in bone loss measurement between imaging modality, measurement method, and observers may lead to differences in treatment in up to 34% of cases. Linear CT measurements resulted in the most aggressive treatment recommendations.Level Of Evidence: Retrospective Comparative Study: Diagnostic, Level III. [ABSTRACT FROM AUTHOR]

The purpose of this study was to determine whether preoperative skin preparation with hydrogen peroxide reduces intraoperative culture positivity for Cutibacterium acnes in shoulder arthroplasty. This was a prospective, controlled, parallel/noncrossover, nonrandomized, single-blinded trial registered at clinicaltrials.gov. We included a consecutive series of patients scheduled to undergo primary anatomic or reverse total shoulder arthroplasty. The first group of patients underwent a standard skin preparation and the second group underwent the same preparation with the addition of hydrogen peroxide. We then took skin, dermis, glenohumeral joint, and air (negative control) aerobic and anaerobic culture swabs. We blinded the laboratory analyzing the samples. An a priori power analysis determined that 56 patients would be needed to see a 50% reduction in culture positivity rates. We also conducted a post hoc gender-stratified analysis. Between January 2017 and October 2018, the authors performed 124 primary shoulder arthroplasties, of which we included 65 and collected samples on 61. There were no demographic differences. There were fewer patients within the peroxide group with triple-positive cultures (skin, dermis, and joint) (0% vs. 19%, P =.024) and positive cultures from the joint (10% vs. 35%, P =.031). In our subgroup analysis, these differences were only significant in males. The vast majority of positive cultures were with C. acnes. Although larger, randomized studies are needed, adding hydrogen peroxide to the preoperative skin preparation may be a low-cost, low-risk method to reduce deep tissue contamination with C. acnes , particularly within males. [ABSTRACT FROM AUTHOR]

It remains unclear whether changes in scapular rotation influence the surgeon's ability to achieve resting radiographic neutral or inferior baseplate tilt at final follow-up. The purposes of this study were (1) to determine whether reverse total shoulder arthroplasty (RTSA) changes the resting scapular rotation, (2) to determine the association between glenoid inclination with respect to the scapula (β angle) and resting scapular rotation, and (3) to determine the β angle threshold that will most likely lead to resting radiographic neutral or inferior baseplate tilt relative to the thorax. This was a retrospective radiographic study. Patients with adequate-quality standing anteroposterior and Grashey radiographs obtained preoperatively and after primary RTSA at a minimum of 1 year were included. Glenoid inclination (β angle) was measured between the supraspinatus fossa and the glenoid. Resting scapular rotation was measured between the supraspinatus fossa and a vertical line. Baseplate tilt was then calculated as the angle between the glenoid and a vertical line. The study included 74 patients with a mean follow-up period of 3 years (range, 1-9 years). Scapular rotation changed 2° ± 12° (mean ± standard deviation) into upward rotation (P =.048). No association was found between the β angle and scapular rotation. In 71% of patients with a neutral or inferior baseplate tilt, a postoperative β angle greater than 85° was found. Resting radiographic scapular rotation changed 2° into upward rotation with RTSA and was not associated with the β angle. If the β angle is greater than 85°, resting radiographic baseplate tilt will most likely be inferior or neutral. [ABSTRACT FROM AUTHOR]

The purpose of this study was to identify factors associated with variation in direct costs with shoulder arthroplasty. This was a retrospective study of all shoulder arthroplasties performed at a single facility between July 1, 2011, and November 30, 2016. We collected patient factors, indications, procedure (including implant details), implant brand (A, B, and other), and complications. We collected direct costs over a 90-day period using a validated internal tool. We identified patient and procedure characteristics associated with costs using multivariable generalized linear models. A total of 361 patients were included, 19% with revision arthroplasty procedures, 32% with anatomic total shoulder arthroplasties, and 66% with reverse total shoulder arthroplasties (RTSAs). Of total costs, 13% were operative facility utilization costs and 58% were operative supply costs. Factors associated with increased total cost included younger age (P =.002) and an indication for surgery of other, that is, not osteoarthritis, a failed arthroplasty, or the sequelae of a rotator cuff tear (P =.030). Factors associated with increased operative costs included younger age (P =.002), use of an RTSA (P <.001), use of a bone graft (P <.001), implant brand B (P =.098), implant brands other than A and B (P =.04), the sequelae of a rotator cuff tear as an indication for surgery (P =.041), or an indication for surgery of other (P =.007). Most short-term (90-day) costs with shoulder arthroplasty are operative costs. Nonmodified factors associated with increased cost included younger age and less common indications for surgery, whereas potentially modifiable factors included the intraoperative use of a bone graft, implant brand, and RTSA use. [ABSTRACT FROM AUTHOR]

Shoulder arthroplasty has advanced considerably in recent decades, but the most recently published long-term outcomes continue to have unacceptably high failure rates, especially in young patients. However, there are several future frontiers that offer the promise of improved implant longevity and function including advances in surgical approach, such as subscapularis-sparing approaches and computer-assisted surgical planning; advances in humeral component fixation, such as stemless, short-stem, and convertible implants; advances in bearing surfaces, such as pyrocarbon, ceramic, and metal-on-metal; and advances in glenoid component geometry and fixation, such as augmented components, in-growth pegs, and inlay glenoid components. [ABSTRACT FROM AUTHOR]

Background Rotator cuff muscle volume is associated with outcomes after cuff repair and total shoulder arthroplasty. Muscle area on select magnetic resonance imaging (MRI) slices has been shown to be a surrogate for muscle volume. The purpose of this study was to determine whether computed tomography (CT) provides an equivalent measurement of cuff muscle area to a previously validated MRI measurement. Methods We included 30 patients before they were undergoing total shoulder arthroplasty with both preoperative CT and MRI scans performed within 30 days of one another at 1 institution using a consistent protocol. We reoriented CT sagittal and MRI sagittal T1 series orthogonal to the scapular plane. On both CT and MRI scans, we measured the area of the supraspinatus, infraspinatus–teres minor, and subscapularis on 2 standardized slices as previously described. We calculated intraclass correlation coefficients and mean differences. Results For the 30 subjects included, when MRI and CT were compared, the mean intraclass correlation coefficients were 0.989 (95% confidence interval [CI], 0.976-0.995) for the supraspinatus, 0.978 (95% CI, 0.954-0.989) for the infraspinatus–teres minor, and 0.977 (95% CI, 0.952-0.989) for the subscapularis. The mean differences were 0.2 cm2 (95% CI, 0.0-0.4 cm2) for the supraspinatus (P =.052), 0.8 cm2 (95% CI, 0.1-1.4 cm2) for the infraspinatus–teres minor (P =.029), and –0.3 cm2 (95% CI, –1.2 to 0.5 cm2) for the subscapularis (P =.407). Conclusion CT provides nearly equivalent measures of cuff muscle area to an MRI technique with previously validated reliability and accuracy. While CT underestimates the infraspinatus area as compared with MRI, the difference is less than 1 cm2 and thus likely clinically insignificant. [ABSTRACT FROM AUTHOR]

Abstract Various surgical techniques exist for rotator cuff repair that provide a suitable environment for tendon–bone healing. Arthroscopic recreation of transosseous repairs, which had previously been performed by open or miniopen techniques, can now be performed; however, arthroscopic, transosseous passage of suture material can be challenging technically. There are potential biologic and cost-saving advantages of arthroscopic transosseous rotator cuff repair that make an efficient and reproducible technique desirable for arthroscopists. The technique for arthroscopic transosseous rotator cuff repair using a knotless anchor-based system is demonstrated in the current Technical Note. Potential advantages of this construct include excellent biomechanics, enhanced footprint vascularization, and utility in poor bone quality while using minimal anchor numbers. Further studies will be needed to elucidate healing rates and clinical outcomes. [ABSTRACT FROM AUTHOR]

Background The objectives of this study were to determine whether glenoid inclination (1) could be measured accurately on magnetic resonance imaging (MRI) using computed tomography (CT) as a gold standard, (2) could be measured reliably on MRI, and (3) whether it differed between patients with rotator cuff tears and age-matched controls without evidence of rotator cuff tears or glenohumeral osteoarthritis. Methods In this comparative retrospective radiographic study, we measured glenoid inclination on T1 coronal MRI corrected into the plane of the scapula. We determined accuracy by comparison with CT and inter-rater reliability. We compared glenoid inclination between patients with full-thickness rotator cuff tears and patients aged >50 years without evidence of a rotator cuff tear or glenohumeral arthritis. An a priori power analysis determined adequate power to detect a 2° difference in glenoid inclination. Results (1) In a validation cohort of 37 patients with MRI and CT, the intraclass correlation coefficient was 0.877, with a mean difference of 0° (95% confidence interval, −1° to 1°). (2) For MRI inclination, the inter-rater intraclass correlation coefficient was 0.911. (3) Superior glenoid inclination was 2° higher (range, 1°-4°, P  < .001) in the rotator cuff tear group of 192 patients than in the control cohort of 107 patients. Conclusions Glenoid inclination can be accurately and reliably measured on MRI. Although superior glenoid inclination is statistically greater in those with rotator cuff tears than in patients of similar age without rotator cuff tears or glenohumeral arthritis, the difference is likely below clinical significance. [ABSTRACT FROM AUTHOR]

Background The purpose of this study was to determine the effect of humeral articular component positioning on changes in patient-reported outcomes after anatomic total shoulder arthroplasty. Methods This was a retrospective series of consecutive patients at 2 high-volume referral centers. The study included patients with (1) a preoperative and postoperative radiograph demonstrating a perfect or nearly perfect profile of the humerus and implant and (2) Simple Shoulder Test, visual analog scale for pain, and American Society of Shoulder and Elbow Surgeons (ASES) Standardized Shoulder Assessment scores preoperatively and at greater than 2 years postoperatively. Head height, head diameter, tuberosity-to-head height distance, inclination, and medial offset of the center of rotation (COR) were measured preoperatively and postoperatively. Distance and direction from the ideal COR to the reconstructed center of rotation was measured. Measurements were correlated with improvement in functional outcomes. Results The study included 95 patients, aged 66 ± 9 years, with a mean follow-up of 4.3 ± 1.7 years. An a priori power analysis suggested that a sample size of 95 patients provided 80% power to detect correlations of R 2  = 0.07. The COR shift was >2 mm in 62% of patients and >4 mm 15%. Thirty-two percent had a change of ASES of <21 points. On multivariate analysis, there were no significant associations between any change in measured prosthetic radiographic parameters and changes in the visual analog scale, Simple Shoulder Test, or ASES scores ( P  > .05). Conclusion In this retrospective analysis of total shoulder arthroplasty in which most components were well positioned, humeral component positioning did not associate with change in postoperative outcomes. These findings should be prospectively confirmed. [ABSTRACT FROM AUTHOR]

Background: The purpose of this study was to simultaneously examine costs, functional outcomes, and tendon healing after arthroscopic rotator cuff repair.Methods: This was a retrospective, single-surgeon, single-hospital study. Pre- and postoperative Simple Shoulder Test (SST), visual analog scale (VAS) pain, and American Shoulder and Elbow Surgeons (ASES) scores, and postoperative magnetic resonance images (MRIs) were obtained. Direct costs were derived using a unique, validated tool. Costs included overall total direct cost, which included facility use costs, medication costs, supply costs, and other ancillary costs.Results: 85 patients had a minimum 1-year follow-up of functional outcomes (mean of 1.24 years, range 1-3.2 years) and 56 of 85 (66%) had postoperative MRI healing data at an average follow-up of 1.3 years (range 1-3.2 years). Increased direct cost was associated with ASA class III (P < .001) compared with ASA class I, procedures performed at the main operative room (P = .017) compared with those at the surgical center, single-row repair (P < .001) compared with double-row repair, medium and large tear sizes (P < .001 and P = .001) compared with small tear, and increased number of anchors (P ≤ .001 or P < .039 for each additional). Arthroscopic biceps tenodesis was associated with decreased improvement in SST, VAS-pain, and ASES scores (P < .001, .012, and .024), whereas infraspinatus atrophy and large/massive tear size was associated with decreased improvement in ASES scores (P = .03). Obesity (P = .004) and smoking (P = .034) were associated with greater improvement in VAS-pain scores as these were associated with decreased preoperative scores. Seventy percent of tears healed.Conclusions: Within our study, factors that increased direct costs were outcome neutral, and factors that improved outcome were cost neutral.Level Of Evidence: Level IV, retrospective. [ABSTRACT FROM AUTHOR]

Background This study evaluated the psychometric properties of the Patient-Reported Outcomes Measurement Information System (PROMIS) Physical Function (PF) instrument administered through computerized adaptive testing (CAT) compared with the traditional full-length Disabilities of the Arm, Shoulder and Hand (DASH). Methods The PROMIS PF CAT and the DASH were administered to 1759 patients seeking care for elbow conditions. This study used Rasch partial credit modeling to analyze the instruments with item fit, internal reliability, response category thresholds, dimensionality, local independence, gender differential item functioning, and floor and ceiling effects. Results The PROMIS PF CAT and DASH had satisfactory item fit for all but 1 item on both measures. Internal reliabilities were high for both measures. Two items on the DASH and 4 items on the PF CAT showed nonordered category thresholds. Unidimensionality was adequate, and local independence was supported for both instruments. Gender bias was found for 4 items on the PF CAT and 12 items on the DASH. Both measures had adequate instrument targeting and satisfactory floor and ceiling effects. Conclusion The PROMIS PF CAT and the DASH both showed sufficient unidimensionality, good item fit, and good local independence with the exception of high levels of gender item bias, particularly for the DASH. Further scale evaluation should address item bias and item response categories for these instruments. Overall, the PROMIS PF CAT is an effective outcome instrument to measure function in patients with elbow disorders that requires significantly fewer questions than the DASH. [ABSTRACT FROM AUTHOR]

Background Very limited information exists about factors affecting direct clinical costs of rotator cuff repair surgery. The purpose of this study was to determine the direct cost of outpatient arthroscopic rotator cuff repair surgery using a unique value-driven outcomes tool and to identify patient- and treatment-related variables affecting cost. Methods Cost data were derived for arthroscopic rotator cuff repairs performed by 3 surgeons from March 2014 to June 2015 using the value-driven outcomes tool. Costs included overall total direct cost, which included facility utilization costs, medication costs, supply costs, and other ancillary costs. Univariate and multivariate regressions were performed to determine the effect of various patient-related and surgical-related factors on costs. Results There were 170 arthroscopic rotator cuff repairs performed during the study period. Multivariate analysis showed significant correlations between higher total direct cost and the presence of a subscapularis repair being performed ( P  = .015) and total number of anchors used ( P  < .0001). Higher body mass index, severe systemic illness, 1 of the 3 surgeons, biceps tenodesis using an anchor, and total sum of anchors were correlated with higher facility utilization costs ( P  < .04). Severe systemic illness, addition of a subscapularis repair, 1 of the 3 surgeons, and additional subacromial decompression were correlated with higher pharmacy costs ( P  < .006). The addition of a subscapularis repair, total sum of anchors, and severe muscle changes to the supraspinatus were correlated with higher supply costs ( P  < .015). Conclusions From a direct cost perspective, implementation of strategies to reduce overall costs should focus on reducing overall anchor quantity or price. [ABSTRACT FROM AUTHOR]

Purpose: To compare the biomechanics of a transosseous equivalent (TOE) repair using medial and lateral anchors with tape to a transosseous knotless (TOK) tape repair with only laterally placed intraosseous anchors.Methods: One of 2 different repairs were performed on 8 paired specimens: (1) transosseous equivalent (TOE) tape repair or (2) transosseous knotless (TOK) tape repair. Specimens were mounted on a materials testing machine and loaded in uniaxial tension to measure cyclic construct gap formation, followed by failure testing. Paired t tests were used to compare gapping, ultimate stiffness, and failure loads. Fisher exact test was used to compare modes of failure (soft tissue failure vs construct failure).Results: Peak cyclic gapping, failure stiffness, and ultimate failure loads did not differ between TOE and TOK repairs (P = .140 for gapping, P = .106 for stiffness, and P = .672 for peak failure loads). All TOK repairs failed via soft tissue failure medial to the medial suture line, with no construct failures. TOE repairs failed more often through construct failure (anchor migration or suture-bone interface cut through) than TOK repairs (P = .026).Conclusion: TOK repairs only failed through soft tissue whereas TOE repairs failed through both soft tissue and the repair construct. Despite 50% fewer suture anchors in the TOK repairs than the TOE repairs, cyclic gapping and ultimate stiffness and failure loads were not significantly different.Clinical Relevance: The transosseous knotless construct presented is a 2-anchor construct that is equivalent in biomechanical function to a traditional 4-anchor construct, reducing anchor load in the tuberosity. [ABSTRACT FROM AUTHOR]