Search

Introduction This study assessed the frequency of dentinal microcracks using a cadaver mandible model in teeth instrumented with TRUShape (TS; Dentsply Sirona, York, PA), WaveOne Gold (WO, Dentsply Sirona), or K-files (KF) compared with an uninstrumented control group (CG). Methods Fifteen human mandibles with 95 single-rooted teeth were randomly distributed into the following groups: CG (no preparation, n = 11), TS ( n = 28), WO ( n = 28), and KF (step-back preparation with K-Flex-o-files [Dentsply Sirona], n = 28). Teeth were prepared to apical sizes of #25/.06 or #25/.07; overlying bone was removed, and then teeth were lifted out of the socket and sectioned at 3, 6, and 9 mm from the apex using a low-speed saw. Resulting slices were photographed at 20× and 25× magnification. Three independent and blinded evaluators assessed the images for the presence of dentinal microcracks and their extension, direction, and location. The chi-square test was used for statistical analysis ( P < .05). Results In the final sample of 83 teeth for the 4 groups, microcracks were found in 10 of 33, 13 of 66, 16 of 69, and 21 of 81 sections for CG, TS, WO, and KF, respectively. There were no significant differences in the frequency of microcracks among the CG, TS, WO, or KF instruments overall or when comparing section levels (3 mm [ P = .9], 6 mm [ P = .18], or 9 mm [ P = .69], respectively, from the apex). There were also no significant differences in the extension, direction, or location of the dentinal microcracks among all groups ( P > .05). Conclusions There was no difference in the frequency of microcracks among the experimental groups instrumented with TS, WO, and KF or uninstrumented controls. [ABSTRACT FROM AUTHOR]

Currently, there are no studies evaluating the impact of 3-dimensional (3D) printed models on endodontic surgical treatment planning. The aims of this study were: 1) to determine if 3D models could influence treatment planning; and 2) to assess the effect of 3D supported planning on operator confidence. Endodontic practitioners (n = 25) were asked to analyze a preselected cone beam computed tomography (CBCT) scan of an endodontic surgical case and answer a questionnaire that elucidated their surgical approach. After 30 days, the same participants were asked to analyze the same CBCT scan. Additionally, participants were asked to study and to perform a mock osteotomy on a 3D printed model. The participants responded to the same questionnaire along with a new set of questions. Responses were statistically analyzed using chi square test followed by either logistic or ordered regression analysis. Adjustment for multiple comparison analysis was done using a Bonferroni correction. Statistical significance was set at ≤0.005. The availability of both the 3D printed model and the CBCT scan resulted in statistically significant differences in the participants' responses to their ability to detect bone landmarks, predict the location of osteotomy, and to determine the following: size of osteotomy, angle of instrumentation, involvement of critical structures in flap reflection and involvement of vital structures during curettage. In addition, the participants' confidence in performing surgery was found to be significantly higher. The availability of 3D printed models did not alter the participants' surgical approach but it significantly improved their confidence for endodontic microsurgery. [ABSTRACT FROM AUTHOR]

Mineral trioxide aggregate (MTA) has been a revolutionary material in endodontics. Since its introduction in the 1990s several studies have demonstrated its use in various clinical applications. MTA has been extensively studied and is currently used for perforation repairs, apexifications, regenerative procedures, apexogenesis, pulpotomies, and pulp capping. This article will review the history, composition, research findings, and clinical applications of this versatile endodontic material. [ABSTRACT FROM AUTHOR]

Mineral trioxide aggregate (MTA) has been a revolutionary material in endodontics. Since its introduction in the 1990s several studies have demonstrated its use in various clinical applications. MTA has been extensively studied and is currently used for perforation repairs, apexifications, regenerative procedures, apexogenesis, pulpotomies, and pulp capping. This article will review the history, composition, research findings, and clinical applications of this versatile endodontic material. [ABSTRACT FROM AUTHOR]

Introduction The purpose of this prospective clinical study was to evaluate the clinical outcome of endodontic microsurgery on roots exhibiting the presence or absence of dentinal defects at 1-year and 3-year follow-up period. Methods One hundred fifty-five teeth were treated with periapical microsurgery using a modern microsurgical protocol in a private practice setting. The root apices were resected and inspected for dentinal defects with a surgical operating microscope and a 0.8-mm head diameter light-emitting diode microscope diagnostic probe light. After inspection, root-end preparations were performed using ultrasonic tips, and root-end fillings were placed. Follow-up visits occurred at 1 year and 3 years postoperatively. The primary outcome measure used was the change in the radiographic apical bone density, and the secondary outcome measure used was the absence of clinical symptoms. Results Of the 155 treated teeth, a total of 134 teeth were assessed at the 1-year follow-up and 127 teeth at the 3-year evaluation. In the “intact” group, 94.8% healed at 1 year, and 97.3% healed at 3 years. In the “dentinal defect” group, 29.8% healed at 1 year, and 31.5% healed at 3 years. The baseline root condition of either “dentinal defect” or “intact” showed a statistical difference in the healing outcome at both 1 and 3 years. Conclusions This prospective periapical microsurgery study showed a significant superior clinical outcome for intact roots when compared with roots with dentinal defects at both 1 year and at 3 years postoperatively. [ABSTRACT FROM AUTHOR]