Search

Most marine renewable energy (MRE) technologies are still in their infancy. Many uncertainties remain regarding MRE systems’ impacts on the marine environment and species where they are deployed, which is one of the major hurdles for these systems to be widely adopted at a commercial scale. Currently, the primary technologies to monitor marine animals’ behavior around existing or potential MRE deployment sites are optical and acoustic imaging. However, these methods cannot identify individual animals and thus are less useful in identifying protected species and studying their behavior. Implantable acoustic transmitters with unique identification codes could serve as a complementary technology. To minimize potential bias introduced to the study results, the implanted transmitters must be sufficiently small and light to not affect the animals’ behavior while still having acceptable signal strengths and service life. Recently, we developed a new miniaturized acoustic transmitter that offers a significantly improved signal strength and service life (140 days [projected value] at a 5-s transmission interval) in a smaller and lighter package (0.45 g in the air), compared to the existing technologies. The detection range and detection efficiency of the new transmitter were tested in an actual marine environment and demonstrated a detection range of up to 330 m, a 65% improvement over the existing commercial counterparts operating at similar frequencies. Here, we report the design principles, performance, and manufacturing procedure of the transmitter. Theoretical estimates of the detection range, the actual range, and detection efficiency results from the field testing are presented.

Sulfonamide antibiotics are potentially harmful to the ecological environment and human health, and control of pollution with these compounds has received much attention. In this study, removal of the four sulfonamides sulfamethoxazole, sulfamethazine, sulfamethazine, and sulfamethoxam- ine from the water was investigated using a composite material prepared from peanut shells and sulfonamide-degrading bacteria. Adsorption–degradation of the sulfonamides with the composite material was investigated using orthogonal static experiments and dynamic experiments. Scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectrometry, and other microscopic detections and analytical techniques were used to explore the mechanism of action. When the sulfonamide concentration was 0.5 mg/L, the removal rates (%) of sulfamethoxazole, sulfamethazine, sulfamethazine, and sulfamethoxamine by the peanut shell composite were 89.69%, 78.39%, 71.38%, and 88.55%, respectively. The optimum conditions for preparation of the composite material were 50 mL of basic medium, a peanut shell:bacteria ratio of 1.5 g/2.5 mL, and a fixation time of 36 h. The dynamic experiments showed that the composite material performed well for removal of sulfonamides present at the low (0.05 mg/L) and high (5.0 mg/L) concentrations, with average removal rates of 79.89% and 61.53%, respectively. The removal of sulfonamides in water by the composite material occurred mainly by physical and chemical adsorption and biodegradation. Physical and chemical adsorption occurred through the porous structure and active functional groups (C–O, –OH, N=C–O, CH, C=O, –CH3, and –CH2–) of the peanut shell composite. Biodegradation mainly involved metabolism by sulfonamide-degrading bacteria immobilized on the peanut shells.

Recently, an acoustic microtag, called the Eel–Lamprey Acoustic Tag (ELAT), was developed for use in juvenile American Eel Anguilla rostrataand Pacific Lamprey Entosphenus tridentatus. The ELAT (12.0 × 2.0 mm; 0.088 g in air) has the potential to be used to study other small‐bodied fishes. In this pilot study, juvenile Chinook Salmon Oncorhynchus tshawytscha52–99 mm fork length (FL) were surgically implanted with an ELAT (n= 99) or remained untagged (control; n= 101). Fish were held for 30 d to evaluate survival, tag retention, and growth. Survival did not differ significantly between control (n= 98 or 97.0%) and tagged fish (n= 95 or 95.9%). Logistic regression analysis suggested that survival was influenced by initial FL and tag burden. Mortalities only occurred in tagged fish with initial FLs of ≤65 mm (FL range = 57–65 mm; tag burdens = 3.8–5.9%). However, a tagged fish with an initial FL of 62 mm or an initial tag burden of 4.1% (FL range = 58–64 mm) was predicted to have a 90% chance of survival, and the smallest fish that survived the study was 54 mm FL (1.8 g; tag burden = 4.9%). Tag retention was high (99%), with only one fish expelling an ELAT during the study. Control fish grew slightly larger than the tagged individuals, but differences in final pooled FLs and weight gains were not significant. Our results demonstrate the successful surgical implantation of the ELAT into Chinook Salmon as small as 54 mm FL (1.8 g).

Previous studies reported that the electrical output of triboelectric nanogenerator (TENG) materials is higher at low temperatures (below −20 °C) than at room temperature, indicating that a TENG device may be suitable in low-temperature environments such as the Arctic Ocean. However, research on TENG systems for extreme weather conditions (temperatures as low as) −40 °C is lacking. This paper presents the design of Arctic-TENG, which efficiently generates electricity to power a satellite communication system in Arctic Ocean conditions. Arctic-TENG was designed for low-temperature operations and performs better at cold temperatures than at room temperature. Using an out-of-water wave simulator at 0.2 Hz, the peak power density of Arctic-TENG reached 21.4 W/m3. Realistic energy requirements were obtained by implementing a satellite communication system, and the available energy from Arctic-TENG was measured and evaluated considering the available wave energy in the Arctic Ocean. The total energy generated per year from Arctic-TENG is 8.59 kJ. One Arctic-TENG can transmit 540 bytes of data per day over a year, which demonstrates the power supply capability of Arctic-TENG for long-term operation of a satellite communication system.

The current minimum size for tagging Chinook Salmon Oncorhynchus tshawytschain the Columbia River basin with acoustic transmitters is ≥95 mm FL. Using a newly developed cylindrical microacoustic transmitter (AT; weight in air, 0.22 g), our objective was to evaluate the minimum size of Chinook Salmon for tagging. We measured Chinook Salmon survival and the retention of transmitters and viscera after their exposure to rapid decompression (n= 399) or shear forces (n= 308) that simulated dam passage. Fish (69–107 mm FL) were implanted with an AT (AT‐only) or an AT and a PIT tag (weight in air = 0.10 g; AT+PIT) through a 3‐mm incision with no sutures, or did not receive an incision or tag (untagged control fish). Tag burden averaged 2.9% (range, 1.4–6.2%) in the AT‐only group and 4.2% (range, 2.0–7.9%) in the AT+PIT group. Proportional survival and the retention of transmitters and viscera was significantly lower for AT‐only (0.70) and AT+PIT (0.54) fish than for untagged fish (0.85) after their exposure to pressure change scenarios. No transmitters were fully expelled, but 9% of AT‐only and 22% of AT+PIT salmon had protruding viscera or transmitters. Following shear exposure, the proportional survival and retention of transmitters and viscera was significantly lower for AT‐only (0.70) and AT+PIT (0.61) fish than for untagged fish (0.98). Visceral expulsion was attributed to 90% and 93% of mortal injuries in AT‐only and AT+PIT fish, respectively. In both tests the tagged fish suffered more mortal injuries and death than did untagged fish over the range of tag burdens tested, and no tag burden threshold below which tagged and untagged fish performed similarly was found. As such, a generalized linear model that included tag burden as a predictor variable provided the best fit to the survival data. Without a significant tag burden threshold, we recommend the minimum size for tagging Chinook Salmon using the transmitters and PIT tags evaluated, applied with a 3‐mm incision and no sutures, should remain at 95 mm FL.

Microbatteries play a critical role in determining the lifetime of downsized sensors, wearable devices, medical applications, and animal acoustic telemetry transmitters among others. More often, structural batteries are required from the perspective of aesthetics and space utilization, which is however rarely explored. Herein, we discuss the fundamental issues associated with the rational design of practically usable high energy microbatteries. The tubular shape of the cell further allows the flexible integration of microelectronics. A functioning acoustic micro-transmitter continuously powered by this tubular battery has been successfully demonstrated. Multiple design features adopted to accommodate large mechanical stress during the rolling process are discussed providing new insights in designing the structural microbatteries for emerging technologies.

Reservoir operations may alter the characteristics of Flood Frequency Curve (FFC) and challenge the basic assumption of stationarity used in flood frequency analysis. This paper presents a combined data‐modeling analysis of reservoir as a nonlinear filter of runoff routing that alters the FFCs. A dimensionless Reservoir Impact Index (RII), defined as the total upstream reservoir storage capacity normalized by the annual streamflow volume, is used to quantify reservoir regulation effects. Analyses are performed for 388 river stations in the contiguous U.S. using the first two moments of the FFC, mean annual maximum flood (MAF) and coefficient of variations (CV), calculated for the pre and post‐dam periods. It is found that MAF generally decreases with increasing RII but stabilizes when RII exceeds a threshold value, and CV increases with RII until a threshold value beyond which CV decreases with RII. Hence depending on the magnitude of RII, reservoir regulation acts as a filter to increase or reduce the nonlinearity of the natural runoff routing process and alters flood characteristics. The nonlinear relationships of MAF and CV with RII can be captured by three reservoir models with different levels of complexity, suggesting that they emerge from the basic flood control function of reservoirs. However, the threshold RII values in the nonlinear relationships depend on the more detailed reservoir operations and objectives that can only be captured by the more complex reservoir models. Our conceptual model may help improve flood‐risk assessment and mitigation in regulated river systems at the regional scale. Nonlinear filtering effects of reservoirs on FFCs analyzedThreshold behavior revealed in FFC changing with reservoir regulation capacityUnderlying processes consistently identified using models with varying complexity

Triboelectric nanogenerator (TENG) systems have been demonstrated to generate power with high density. However, the electrical output power obtained from wave energy harvesting using TENG systems is typically limited to several milliwatts. To address this limitation and support various ocean buoy systems, an efficient method to scale-up TENG systems is required. In this paper, we present a self-powered ocean buoy (SPOB) incorporating a disk-type, soft-contact, mechanical frequency regulator TENG (DSMFR-TENG). The mechanical frequency regulator (MFR) enables the conversion of low-frequency wave energy to high-speed mechanical rotation, facilitating high power generation with the disk-type TENG. The SPOB was tested in a wave tank, reaching a peak power output of 470mW and an average power output of 130mW after the MFR released the rotational energy. To further enhance the functionality of the buoy, the DSMFR-TENG and a microcontroller, temperature sensor, and acoustic transmitter were integrated with the SPOB. The acoustic transmitter successfully transmitted signals 7, 23, and 30 times over a one-minute period at wave frequencies of 0.33Hz, 0.5Hz, and 1Hz, respectively, thereby demonstrating the power supply capability of the TENG system for ocean buoys.

Cylindrical triboelectric nanogenerators (C-TENGs) have been designed for low frequency wave energy harvesting. However, the random, and low amplitude and frequency of the ocean waves represent a major challenge for the operation and performance of most C-TENGs. A C-TENG must be able to operate and be triggered by any wave conditions, even in the middle of the ocean, with uniform, low amplitude, and low frequency water waves. Here, a frequency-multiplied cylindrical TENG (FMC-TENG) that uses magnets to store potential energy and instantly release it to produce high frequency kinetic energy, was designed to increase the operating frequency of the TENG using low frequency, uniform water waves and increase the power generated. A semi-analytical modeling of the FMC-TENG was performed to theoretically verify its effectiveness. Then, the electrical characteristics of the FMC-TENG were evaluated by comparison with a conventional C-TENG in a wave motion simulator. The FMC-TENG was optimized in a 12 m long water tank, and its peak power density reached 6.67 W/m3under a wave frequency of 0.33 Hz. Finally, an array of FMC-TENGs successfully powered an acoustic transmitter, demonstrating the ability to power an ocean observation system.

Chum Salmon Oncorhynchus ketaalevins developing in gravel downstream of Bonneville Dam on the Columbia River are exposed to elevated total dissolved gas (TDG) when water is spilled to move migrating salmon smolts to the ocean. We studied whether alevins that were exposed to six levels of dissolved gas ranging from 100% to 130% TDG at three development periods between hatch and emergence (hereafter, early, middle, and late stages) experienced differential mortality, growth, gas bubble disease, or seawater tolerance. Each life stage was exposed for 49 d (early stage), 28 d (middle stage), or 15 d (late stage) beginning at 13, 34, and 47 d posthatch, respectively, through emergence. Mortality for all stages was estimated to be 8% (95% confidence interval [CI] = 4–12%) when dissolved gas levels were less than 117% TDG. Mortality increased as dissolved gas levels rose above 117% TDG; the lethal concentration producing 50% mortality was 128.7% TDG (95% CI = 127.2–130.3% TDG) in the early and middle stages. There was no evidence that gas exposure affected growth. The proportion of fish with gas bubble disease increased with increasing gas concentrations, and bubbles occurred most commonly in the nares and gastrointestinal tract. Early stage fish exhibited higher ratios of filamental to lamellar gill chloride cells than late-stage fish, and these ratios increased and decreased for early and late-stage fish, respectively, as gas levels increased; however, there were no significant differences in mortality between life stages after 96 h in seawater. The study results suggest that water quality guidelines for dissolved gas (=105% TDG) offer a conservative level of protection to Chum Salmon alevins incubating in gravel habitat downstream of Bonneville Dam. Received June 1, 2012; accepted November 13, 2012

AbstractChum Salmon Oncorhynchus ketaalevins developing in gravel downstream of Bonneville Dam on the Columbia River are exposed to elevated total dissolved gas (TDG) when water is spilled to move migrating salmon smolts to the ocean. We studied whether alevins that were exposed to six levels of dissolved gas ranging from 100% to 130% TDG at three development periods between hatch and emergence (hereafter, early, middle, and late stages) experienced differential mortality, growth, gas bubble disease, or seawater tolerance. Each life stage was exposed for 49 d (early stage), 28 d (middle stage), or 15 d (late stage) beginning at 13, 34, and 47 d posthatch, respectively, through emergence. Mortality for all stages was estimated to be 8% (95% confidence interval [CI] = 4–12%) when dissolved gas levels were less than 117% TDG. Mortality increased as dissolved gas levels rose above 117% TDG; the lethal concentration producing 50% mortality was 128.7% TDG (95% CI = 127.2–130.3% TDG) in the early and middle stages. There was no evidence that gas exposure affected growth. The proportion of fish with gas bubble disease increased with increasing gas concentrations, and bubbles occurred most commonly in the nares and gastrointestinal tract. Early stage fish exhibited higher ratios of filamental to lamellar gill chloride cells than late-stage fish, and these ratios increased and decreased for early and late-stage fish, respectively, as gas levels increased; however, there were no significant differences in mortality between life stages after 96 h in seawater. The study results suggest that water quality guidelines for dissolved gas (≤105% TDG) offer a conservative level of protection to Chum Salmon alevins incubating in gravel habitat downstream of Bonneville Dam.Received June 1, 2012; accepted November 13, 2012

AbstractDetermining the fate of juvenile fish that are exposed to elevated temperatures is complicated by the fact that the optimum temperature for the growth and survival of salmonids decreases as the amount of food becomes restricted. In this study, naturally produced juvenile Snake River fall Chinook salmon Oncorhynchus tshawytschawere fed daily ration levels of 1, 4, or 8% of their body weight and exposed to either constant temperatures (10–14°C) or fluctuating temperatures that mimicked the heating rate (1.5°C/h) and maximum daily temperatures (19–23°C) of entrapment pools that form along the shoreline downstream of Hells Canyon Dam when river flows are altered to meet electric power demand. The survival rate for all groups was 99.9%, and there was no evidence that juvenile fall Chinook salmon fed reduced rations and exposed to constant temperatures grew to a greater extent than juvenile fall Chinook salmon exposed to fluctuating temperatures. The only exception was with the 1% ration level in which juvenile fall Chinook salmon that were exposed to a constant 10°C added more weight over the 14-d exposure period (1% of body weight per day [WT/d]) than fish exposed to temperatures that fluctuated from 10°C to 19.0°C (0.3% WT/d) and from 10°C to 22°C daily (0% WT/d). We conclude that the lack of difference in growth rates between the fluctuating and constant temperature regimes at daily ration levels of at least 4% stems from the facts that the rate of temperature change in this study was within the acclimation range for growth, the daily average temperatures were less than thermal optimum values, and the temperature amplitudes were within lethal limits.Received January 16, 2010; accepted November 22, 2010

Determining the fate of juvenile fish that are exposed to elevated temperatures is complicated by the fact that the optimum temperature for the growth and survival of salmonids decreases as the amount of food becomes restricted. In this study, naturally produced juvenile Snake River fall Chinook salmon Oncorhynchus tshawytschawere fed daily ration levels of 1, 4, or 8% of their body weight and exposed to either constant temperatures (10–14°C) or fluctuating temperatures that mimicked the heating rate (1.5°C/h) and maximum daily temperatures (19–23°C) of entrapment pools that form along the shoreline downstream of Hells Canyon Dam when river flows are altered to meet electric power demand. The survival rate for all groups was 99.9%, and there was no evidence that juvenile fall Chinook salmon fed reduced rations and exposed to constant temperatures grew to a greater extent than juvenile fall Chinook salmon exposed to fluctuating temperatures. The only exception was with the 1% ration level in which juvenile fall Chinook salmon that were exposed to a constant 10°C added more weight over the 14-d exposure period (1% of body weight per day [WT/d]) than fish exposed to temperatures that fluctuated from 10°C to 19.0°C (0.3% WT/d) and from 10°C to 22°C daily (0% WT/d). We conclude that the lack of difference in growth rates between the fluctuating and constant temperature regimes at daily ration levels of at least 4% stems from the facts that the rate of temperature change in this study was within the acclimation range for growth, the daily average temperatures were less than thermal optimum values, and the temperature amplitudes were within lethal limits.

Development of more eco-friendly hydroelectric facilities requires better understanding of the biological response of juvenile fish when they migrate through the turbines and other downstream passage facilities. Juvenile fall Chinook salmon Oncorhynchus tshawytschawere exposed to turbulent shear flows in a laboratory by using a fast-fish-to-slow-water mechanism in which test fish were carried by the fast-moving water of a submerged turbulent jet into the slow-moving water of a flume. Fish were released at six nozzle velocities: 6.1 (reference control), 12.2, 15.2, 18.3, 21.3, and 22.9 m/s. The onset of minor and major injuries occurred at 15.2 and 21.3 m/s, respectively. The acceleration magnitude threshold (m/s2) of major injury for the fast-fish-to-slow-water mechanism in this study was found to be significantly higher than that for a slow-fish-to-fast-water mechanism used in a previous study in which test fish were introduced into a turbulent jet from slow-moving water through an introduction tube placed just outside the edge of the jet. Fish responded differently and sustained different injuries when they were subjected to turbulent shear flows under the two exposure mechanisms. This information is applicable to the design and operation of turbines and spillways because these two tested mechanisms simulate the severe hydraulic events fish usually experience during passage at hydropower dams.

AbstractDevelopment of more eco-friendly hydroelectric facilities requires better understanding of the biological response of juvenile fish when they migrate through the turbines and other downstream passage facilities. Juvenile fall Chinook salmon Oncorhynchus tshawytschawere exposed to turbulent shear flows in a laboratory by using a fast-fish-to-slow-water mechanism in which test fish were carried by the fast-moving water of a submerged turbulent jet into the slow-moving water of a flume. Fish were released at six nozzle velocities: 6.1 (reference control), 12.2, 15.2, 18.3, 21.3, and 22.9 m/s. The onset of minor and major injuries occurred at 15.2 and 21.3 m/s, respectively. The acceleration magnitude threshold (m/s2) of major injury for the fast-fish-to-slow-water mechanism in this study was found to be significantly higher than that for a slow-fish-to-fast-water mechanism used in a previous study in which test fish were introduced into a turbulent jet from slow-moving water through an introduction tube placed just outside the edge of the jet. Fish responded differently and sustained different injuries when they were subjected to turbulent shear flows under the two exposure mechanisms. This information is applicable to the design and operation of turbines and spillways because these two tested mechanisms simulate the severe hydraulic events fish usually experience during passage at hydropower dams.

The incipient lethal temperature (ILT) and critical thermal maximum (CTM) methods are used to set temperature limits for fish. However, the standard application of these methods does not always match the temperature regimes that fish experience in the wild. We used alternative methods to determine the thermal tolerance thresholds of juvenile fall-run Chinook salmon Oncorhynchus tshawytschaexposed to the temperature regimes that are common in the entrapment pools that form along the shoreline of the Snake River when flows are altered to meet electric power demand. A modified CTM test with a steady temperature rise (1.5°C/h) showed that one-half the fish died when temperatures reached 27.4–27.9°C and that survival at 25°C was highly variable; the average time to the first death was 9.1 h, varying from 1.7 to 22.5 h. Over 30 d, 99.8% of the fish in the constant temperature regimes (14–22°C) survived. In the fluctuating temperature regimes (which varied from 10–14°C to 22–27.5°C), overall survival was 97.3%; however, only 83.0% and 88.9% survived in the groups that reached daily maximums of 27°C and 27.5°C, respectively. Growth over 30 d in the constant thermal regimes was nearly twice as high as that in the fluctuating regimes, even when daily average temperatures were similar. The maximum growth was 1.9%/d in terms of fork length [FL] and 11.2%/d in terms of weight (WT) at a constant 20°C. The lowest growth occurred in the two groups exposed to daily temperatures of 27°C or more, namely, 0.7–0.8% (FL) and 2.7–3.4% (WT). The results of this study suggest that thermal tolerance tests that expose juvenile fall Chinook salmon to thermal regimes that match the field conditions in entrapment pools along the shoreline of the Snake River provide higher temperature criteria than the standard ILT and CTM methods.

Insufficient service life and the resulting need for battery replacements have been a great challenge for implantable electronic devices. This is particularly true for animal tracking applications, because recapturing animals is often unlikely once they are released to the wild. To tackle this problem, we developed a biomechanical energy harvester that uses a Macro Fiber Composite™ (MFC) piezoelectric beam to harvest the mechanical energy from animals’ body bending movements as the power source for implantable and wearable devices. Prototypes of an underwater acoustic transmitter using this technology were subdermally implanted into juvenile white sturgeon and their energy harvesting performance was evaluated through the device’s transmissions. The fish successfully recovered from the implantation surgery and freely swam inside a tank. The transmitter prototypes in the fish continually transmitted signals for a period up to 5 weeks. A benchtop test setup was also created to emulate the fish’s body bending, estimate the device’s energy harvesting performance in the live fish, and perform accelerated fatigue testing of the energy harvester by applying test parameters learned from a video study of the fish’s body movement and behavior characteristics. The gradual depolarization of the piezoelectric ceramic material in the MFC under cyclic mechanical loading was the main limiting factor for the life span of the energy harvester. Pathways for improvement are proposed to achieve long-term efficacy of powering implantable and wearable electronic devices.

At The Dalles Dam on the Columbia River, fish are believed to sustain injury from exposure to turbulence and from collisions with baffle blocks and end sills in the stilling basin at high spillway discharges. Because taking velocity measurements would be exceedingly difficult in this environment, a system of pressure transducers was installed to record high-frequency pressure data for a range of spillway discharges. The sensors were mounted below two of the spillbays on the tops, faces, and sides of baffle blocks; in the gaps between baffle blocks; and on the top and face of the end sill. Statistical analyses on results from three sensors below one of the two spillways showed that mean pressure increased during head-on flow, decreased in flow separation zones, and was proportional to water depth. Power spectra indicate increased low-frequency spectral power with increased discharge, typical spectral decay rates, and the existence of spectral peaks of possible hydraulic origin. The high-frequency pressure data collected at full scale in extremely turbulent environments will contribute to efforts to improve fish passage and to develop and validate three-dimensional computational fluid dynamics models.

This paper proposes a new node organization mechanism in the storage service provided by the Campus Grid Service Environment. The advantage of this architecture is its ability to aggregate nodes in the order of millions; the corresponding storage space aggregated can attain a petabyte level, which is a significant improvement in comparison with other campus Grids. Furthermore, this architecture is scalable and it can allow more nodes to join the storage pool to increase the storage space. The multilevel linked lists were first developed in order to organize the storage resources that are contributed by the nodes in the campus network. Subsequently, the algorithms were presented to analyze the mechanisms of the nodes: joining and leaving; storage resource scheduling and allocation; and unallocated storage space management. The performance of this system was investigated by employing a stochastic fluid model as the storage space changes with time as a result of the variation of the number of nodes. With this analytical model, the function between the storage allocation probability and the number of nodes was obtained. If more nodes join the campus Grid, the aggregated storage space will provide more available storage resources. If the storage resources allocation rate is less than the storage resources release rate, the available storage resources will increase and vice versa. Copyright © 2006 John Wiley & Sons, Ltd.

High-energy rechargeable lithium metal batteries have been intensively revisited in recent years. Since more researchers started to use pouch cell as the platform to study the fundamentals at relevant scales, safe testing and handling of lithium metal and high-energy lithium metal batteries have become critical. Cautions and safety procedures are needed when handling cycled pouch cells with pulverized lithium metal particles inside. From cell design, electrode preparation, cell fabrication to testing procedure, this work aims to discuss the possible root causes that may initiate cell internal short circuit and raise safety concerns. Safe transfer, disassembly and disposal of cycled Li metal pouch cells are also discussed. The insights provided in this article are applicable for the research on high-energy lithium-ion batteries as well and may inspire more safety strategies to accelerate research innovation by using large-format batteries as the testing vehicle and conduct the research safely.

Modeling analysis of future hydrologic droughts over U.S. is providedRelative contributions from climate change and water managements are quantifiedFuture hydrologic drought will be alleviated by reservoirs but intensified by local water extraction Hydrological drought is a substantial negative deviation from normal hydrologic conditions and is influenced by climate and human activities such as water management. By perturbing the streamflow regime, climate change and water management may significantly alter drought characteristics in the future. Here we utilize a high‐resolution integrated modeling framework that represents water management in terms of both local surface water extraction and reservoir regulation and use the Standardized Streamflow Index to quantify hydrological drought. We explore the impacts of water management on hydrological drought over the contiguous U.S. in a warming climate with and without emissions mitigation. Despite the uncertainty of climate change impacts, local surface water extraction consistently intensifies drought that dominates at the regional to national scale. However, reservoir regulation alleviates drought by enhancing summer flow downstream of reservoirs. The relative dominance of drought intensification or relief is largely determined by the water demand, with drought intensification dominating in regions with intense water demand such as the Great Plains and California, while drought relief dominates in regions with low water demand. At the national level, water management increases the spatial extent of extreme drought despite some alleviations of moderate to severe drought. In an emissions mitigation scenario with increased irrigation demand for bioenergy production, water management intensifies drought more than the business‐as‐usual scenario at the national level, so the impacts of emissions mitigation must be evaluated by considering its benefit in reducing warming and evapotranspiration against its effects on increasing water demand and intensifying drought.