Search

In the past decades, the German paper industry has been increasing the sustainability of paper production by continuously using more recovered paper. Today, recovered paper is an essential secondary raw material to produce new paper. Nevertheless, around 20 % of the paper produced in Germany is still not returned to the recovered paper stream and instead is mostly thermally used. To further increase the use of fibers from recovered paper as secondary raw material and thus, to reduce primary energy consumption and greenhouse gas emissions, new approaches to recycle recovered paper from mixed waste streams are needed. In the research project "Energy savings in paper production by opening up the value chains of recovered paper from lightweight packaging, residual waste and commercial waste" (EnEWA), a treatment process is developed to recover and recycle recovered paper from the mentioned waste streams. The advanced mechanical process to be newly developed consists of dry-mechanical sorting, the manufacturing of economically usable secondary raw materials (defibration), their wet-mechanical dissolution, separation and hygienization and finally their reuse in paper production. This enables the exploitation of new waste streams in material recycling and thus contributes to reduced energy consumption as well as CO2 emissions within the circular economy. Initial material characterization analyses show that on the one hand the quality of the paper discarded in mixed waste streams is sufficient to be used as secondary raw material and that on the other hand up to 50 % of the paper discarded could have been disposed of within the separate paper collection. The results are incorporated in the development of a sorting process for pre-concentrates, which serves as input material for the treatment process to recover paper fibers. In further steps, the results generated will be integrated, for instance, into the future development of the minimum standard for packaging recycling. [ABSTRACT FROM AUTHOR]

The dissemination of emerging electronic devices increases considerably alongside with the Internet of Things (IoT) paradigm. Some key elements considered in these devices (e.g. rare-earth) are becoming critical materials and are associated with serious environmental concerns. Therefore, there is a major requirement for designing differently our electronic technologies at the early stages of the research process. Many reports present the promising properties of paper-based electronics as meant to address this challenge. Through technical and life cycle assessments, this article discusses the main design levers in terms of material and fabrication process choices for the eco-design of paper-electronics water quality sensors. Our results suggest conscientious choices of conductive nanomaterials and additive fabrication techniques. [ABSTRACT FROM AUTHOR]

In Paper and Pulp (P&P) industry resource management scenarios, such as processing cell(s) efficiency reduction, equipment break-down or failures, alternative energy source (biomass and solar energy) utilization/ synchronization with regular energy sources and management decided change in production rate or product quality often occur in industrial processes causing material flow disruption, energy and production losses. In such scenarios, immediate and appropriate actions are required to be taken to minimize energy and production losses. Emerging resource management options tackle these issues through four different ways i.e., by mixing of readymade pulp at various processing stages, by varying the percentage of input raw material, by adopting a parallel utilization of alternative energy sources and by switching on/off some processing units or parallel working segments. These ways are implementable with immediate effect, accurately monitorable and their degree of application can be regulated within a wide range, thus denoted as adaptive solutions. This research work proposes a discrete-event simulation based real-time resource management technique for paper and pulp industry, wherein some resource management challenges are addressed and solved strategically with adaptive solutions. The presented examples validate that using the developed approach, the effective adaptive strategy can be timely planned to resolve occasionally or permanently happening resource management challenges ensuring an un-interrupted material flow throughout the plant along with the minimization of productivity and energy losses. [ABSTRACT FROM AUTHOR]

It is critical for manufacturers to identify quality issues in production and prevent defective products being delivered to customers. We investigate the use of deep neural networks to perform automatic quality inspections based on image processing to eliminate the current manual inspection. A deep neural network was implemented in a real-world industrial case study, and its ability to detect quality problems was evaluated and analyzed. The results show that the network has an accuracy of 94.5%, which is considered good in comparison to the 70–80% accuracy of a trained human inspector. [ABSTRACT FROM AUTHOR]

Small companies encounter difficulties to adapt to new markets with a sustainable perspective. The subject of this article is a paper transformation company which has been eager to develop the organic farming market by developing a new plant support. Alternatives made from plant fibres or plastics exist, such as jute and polypropylene. The main difficulty of this project was to ecodesign a paper product with a multicriteria approach. The factors considered have been divided into two categories. Firstly, the environmental impacts calculated according to the Life Cycle Assessment methodology (on raw material extraction, manufacturing and end-of-life) are summarised. Secondly, the characteristics of the product are discussed in regards to these results and sustainability questions as part of the interpretation phase. Finally, ways of improvement of the LCA methodology to improve the study in terms of geographical representativeness and societal considerations are discussed. [ABSTRACT FROM AUTHOR]

Life Cycle Assessment (LCA) has been used to evaluate the life-cycle Greenhouse Gas (GHG) emissions of pulp and paper production, and most previous studies rely on process-based models for specific product types (e.g., printing paper), industry-average data, or information from a few mills. In this work, a data-mining approach is used to quantify GHG emissions intensities of different paper products manufactured by the U.S. mills. Facility-level emission data collected from publically available governmental databases and mill-level production data collected from the private sector were integrated to track the GHG emissions for different product lines and paper products in mills (in total, 165 mills were matched and analyzed). The results highlight the ranges of GHG emissions intensities by different product groups and categories, and can be used as a transparent data source for LCA practitioners, policymakers, and the pulp and paper industry to perform further analysis on carbon accounting and strategic planning for GHG mitigation. [ABSTRACT FROM AUTHOR]

Abstract To improve energy efficiency of a Paper & Pulp industry, full capacity utilization of the processing equipment and diverse energy source utilities are promoted, while same time processing of diverse raw materials, meeting of strict processing time requirements, seamless material flow and obtaining required product quality are important concerns to be fulfilled. This is similar to a resources management problem while energy is considered as one of the measurable resources, wherein estimation of energy consumptions is crucial/complicated aspect. Discretized form of energy consumption (approximate energy consumed by unit amount of intermediate products at different intermediate processing stages) concept is utilized here with discrete event simulation for consumed energy estimation/analysis. The research deals with a real time working Paper & Pulp industry resource management problem, wherein overall energy consumption rate and production rate were analyzed for some commonly occurring situation of efficiency reduction of the processing station(s). Energy efficient solutions are evaluated with varying production flow (varying the percentage of raw material) and resources management options (turning on/off paper machines). Energy efficient solution which ensures minimum loss in production rate and minimizes disturbances in material flow is suggested for implementation. [ABSTRACT FROM AUTHOR]

Reducing “energy waste” has helped manufacturing companies to systematically improve their productivity. However, optimization goals related to the resource energy (energy efficiency, demand side management, integration of renewables) are still addressed in an isolated manner. Here we present a stepwise methodology on how to unite the different facets of energy usage in a factory planning process. Our results indicate that addressing the energy related planning goals in an integrated manner helps to reduce both life cycle costs and the environmental impact of factories. Future research will refine the presented planning framework and quantify the correlation between conventional and energy related planning targets. [ABSTRACT FROM AUTHOR]

The power of the rotating transverse paper cutting machine is huge because of unreasonable motion. The paper researched the motion mechanism of the structure, transformed the 3D trajectory of rotating blade and paper cutting marks into the same plane space. Ultimately the motion mechanism of the parameters of cutter and paper cutting are established and the reasonable cutting conditions are founded. At last the parameters are optimized according to the relationship of the planning and useless power consumption, achieve the goal of the roller rotate smoothly and the useless power consumption is zero in theory. [ABSTRACT FROM AUTHOR]