Search

This paper aimed to determine the characteristics of physical and mechanical properties of rice straw hand sheet and investigated the optimal conditions for making rice straw paper. The chemical composition of rice straw determined with the TAPPI standards. The conditions of making paper hand sheet composed of pulping time: 2 hours, 4 hours, pulping temperature: 100°C, 130°C, pulping solvent: 2 wt% NaOH, 4 wt% NaOH and bleaching: unbleached pulp, bleached pulp with 2% H2O2. The paper hand sheet was tested based on TAPPI methods, basic weight TAPPI- T410-om-93, thickness TAPPI- T411-om-89, moisture content TAPPI- T412-om-93, brightness TAPPI T452 om-92, opacity TAPPI standard T 425 om-91, burst strength TAPPI T403 om-97, tensile strength TAPPI T494 om-01, and tear strength TAPPI-T414-om-88. The results showed that the optimal conditions of rice straw hand sheet including pulping time: 2 hours, pulping temperature: 100°C, pulping solvent: 2 wt% NaOH, and bleaching: unbleached pulp gave the highest the physical and mechanical properties form other conditions. This conditions showed as the basic weight 62.27 g/m2, thickness 259.30 µ, opacity 93.34 ISO%, burst strength 64.75 kPa.m2/g, tensile strength 95.33 N.m/g, and tear strength 473.55mN.m2/g. In this condition, the paper hand sheet used at the lowest concentration of pulping solvent and non-bleached, which reduces environmental pollution.

Anode surface plays important role for extracellular electron transfer (EET) of exoelectrogenic microbes in microbial fuel cell (MFC). In this report, the electrochemical performance of a TiO2 nanorod array modified carbon paper electrode (TiO2 NRs/CP) is greatly improved by controlled chemical etching process. The etching process keeps the array morphology but yields obvious hollows on tops of TiO2 nanorods. The etched electrode (TiO2 NRs-HOT/CP) exhibits better hydrophilicity than carbon paper (CP) and TiO2 NRs/CP electrode as seen from smaller contact angle (CA) and more attached microbes S.loihica PV-4. Meanwhile, the hollows allow higher local concentration of microbial self-secreted flavins that can act as electron mediators for interfacial electron transfer of PV-4 through in-direct pathway. Accordingly, PV-4 produces larger current density at TiO2 NRs-HOT/CP electrode with maximum current density of 0.038 mA cm –2, which was much higher than that at CP electrode, and almost five times higher than that at un-etched TiO2 NRs/CP electrode.

Panicum repens is a species of grass known by many common names, including torpedo grass, creeping panic, panic rampant, couch panicum, wainaku grass, quack grass, dog-tooth grass, and bullet grass. The paper has been made from non-wood materials for long times. This research was used Panicum repens for made grass pulp as non-wood fiber. The influence of sodium hydroxide (NaOH) concentrations on properties of pulp from Panicum repens was investigated under room temperature. NaOH concentration levels were varied at 0%, 5%, 10%, 15%, and 20%, respectively. Moreover, Paper pulp from Panicum repens was observed by scanning electron microscope (SEM). This research has controlled the length of fiber approximately 0.5-2.5 cm before soaked with NaOH concentration at 1 hour and soak with water for controlled pH value at 7-8. Paper pulp was formed on a sieve. The result showed that color of paper pulp made from Panicum repens was light brown and green. SEM showed that NaOH concentration affects the physical properties of paper pulp. Moreover, true density of paper pulp was also investigated in this research.

In order to study the corresponding relationship between the design and fashion of tea gift package, this paper will analyze and discuss the color design and packaging style of tea gift package. Besides, this paper will also do research on the cultural origin of tea and the value of package, and analyze the influence of package on consumers. Finally, based on the research, the author had design a tea gift package that is in accordance with the current trend. This study uses bright yellow and orange as predominant colors to present nobleness of tea of Alishan. The colors used on the packaging will render people associate with harvest in autumn.

In this study, we chose 12 commonly available paper towels from the local market. The compression properties of the paper towels were examined by Kawabata Evaluation System for Fabric (KES-F). Three compression properties namely: (i) compressional linearity (LC), (ii) compression energy (WC) and (iii) compressional resilience (RC) were examined. The experimental results revealed that the compression properties varied within the different paper towels. RC vlaue was used as the key property for discussing the compression properties of paper towels. When different compression properties were correlated and analysed, it was found that no relationship was noted within different compression properties. On the other hand, there was not significant statistically relationship between weight and thickness to RC. It is hope that the results from this study can help the indurstry to improve the compression properties of paper towels for local market.

In this study, 12 commercially available paper towels were collected from the local market. Their tensile properties were investigated by Kawabata Evaluation System for Fabric (KES-F). Four tensile properties namely: (i) extensibility (EMT), (ii) tensile energy (WT), (iii) tensile resilience (RT) and (iv) linearity of WT (LT) were evaluated. Experimental results revealed that the tensile properties varied within the products. EMT was used as the key property for discussing the tensile properties of paper towels. However, when the different tensile properties were correlated, it was found that WT/RT, WT/EMT and RT/EMT had strong Pearson correlation. In addition, there was no significant statistically relationship between weight and thickness to EMT. Based on this study, it can provide some information about the tensile properties of paper towels in local market which may help the industry for further improving the product quality.

12 commercially available paper towels were collected from the local market and studied in this paper. Kawabata Evaluation System for Fabric (KES-F) was used for evaluating their bending properties. Two bending properties namely: (i) bending rigidity (B) and (ii) bending moment (2HB) were evaluated. Experimental results indciated that the bending properties varied within the products. B was used as the key property for discussing the bending properties of paper towels. When the correlations of different bending properties were investigated, it was found that no significant was found between B and 2HB. However, there was significant statistically relationship between weight and B but no relationship between thickness and B. With the use of the results, the product developer could improve the bending properties of the paper towels.

In this paper, we collected 12 commercially available paper towels from the local market and their shearing properties were evaluated by Kawabata Evaluation System for Fabric (KES-F). Three properties namely: (i) shear rigidity (G), (ii) shear stress at 0.5º (2HG) and (iii) shear stress at 5º (2HG5) were studied. Experimental results revealed that the shearing properties varied within the products. G was used as the key property for discussing the shearing properties of paper towels. However, in correlating different shearing properties, it was found that 2HG and 2HG5 had strong Pearson correlation. However, no significant statistically relationship between weight and thickness to G was found. This study may provide data for the industry for the improvement of shearing properties of paper towels for local market.

The quality of product of manufacturing industries depends on dimension accurately and surface roughness quality. There are many types of surface defects and levels of surface roughness quality. Ironing process is one type of metal forming process, which aims to reduce the wall thickness of the cup-shaped or pipes products, thus increasing the height of the wall. Manually surface inspection procedures are very inadequate to ensure the surface in guaranteed quality. To ensure strict requirements of customers, the surface defect inspection based on image processing techniques has been found to be very effective and popular over the last two decades. The paper has been reviewed some papers based on image processing for defect detection. It has been tried to find some alternatives of useful methods for product surface defect detection of ironing process.

Biocomposites sheets were prepared by compression molding from mixtures of corn starch plasticized by glycerol as matrix and cellulose fibers, extracted from used office paper, as reinforcement filler with contents ranging from 0 to 8% wt/wt of fibers to matrix. Properties of composites were determined by mechanical tensile test, differential scanning calorimetry, thermogravimetric analysis, water absorption measurement, and scanning electron microscopy. The results showed that higher fibers content raised the tensile strength and elastic modulus up to 109% and 112%, respectively, when compared to the non-reinforced thermoplastic starch (TPS). The addition of the fibers improved the thermal resistance and decreased the water absorption up to 63.6%. Scanning electron microscopy illustrated a good adhesion between matrix and fibers.

In this study, 12 commercially available paper towels were collected from the market. Their shearing properties were evaluated by Kawabata Evaluation System for Fabric (KES-F). Three properties namely: (i) coefficient of friction (MIU), (ii) deviation of MIU (MMD) and (iii) geometric roughness (SMD). Experimental results revealed that the surface properties varied within the products. When different properties were correlated, it was found that there was not significantly relationship between MIU, MMD and SMD. However, weight and thickness had well statistically relationship to SMD.

Examples of solid and liquid electrical insulations for power transformer are mineral oil and cellulose based paper. As transformers performed their function to step-up or step-down voltage level, its’ insulations will be degraded. Paper insulation is considered the most critical component in a transformer insulation system because it is not easily replaced if compared to oil where it is easily reconditioned in-order to remove water and contaminants. Studies show that temperature, moisture contents and oxygen contributed to paper insulation degradation. Moisture and furanic compound were produced from these deterioration processes. This paper is focused on the formation and effect of moisture to Kraft paper’s life. Levels of moisture contents were obtained from in-service power distribution transformers. These data then is used to assess the Kraft paper’s life by means of Weibull plot. This study shows that level of moisture contents can be used to assess the life of Kraft paper insulation.

This paper presents the performance investigations of the spatial domain image watermarking for camera-captured images on different types of printers and printable materials. We examine the effects of our previous watermarking method based on the modification of image pixels on three types of printers, i.e. inkjet, laser and photo printers, and four different types of printing papers, i.e. uncoated, matte, glossy and semi-glossy papers. In the experiments, the DSLR camera is used as tool to capture the printed watermarked images, while the image registration technique based on projective transformation is used to diminish the RST and perspective distortions in the captured image. The performances in terms of extracted watermark accuracy at equivalent watermarked image quality on different types of printers and printing papers are measured and compared.

The increasing demand in wood fibre consumptions especially in pulp and paper making has pushed forward the search for alternative fibre resources. Non-wood derived fibre could be good candidates due to its abundance availability. Agriculture residues or non-wood annual plants are good potential fibre resource for pulp and paper making. The objective of this study is to determine the suitability of cogon grass as an alternative fibre for pulp and paper making by analysing its chemical and surface morphological properties. The holocellulose, cellulose, lignin, 1% NaOH solubility, hot water solubility and ash contents were quantified to analyse its chemical characteristics. Quantification of chemical compositions was conducted in accordance with relevant Technical Association of the Pulp and Paper Industry (TAPPI) Tests, Kurscher-Hoffner and Chlorite methods. Scanning electron microscopy (SEM) was used to visualize the surface morphology of the cogon grass fibre. Results obtained indicate that the holocellulose (64.93%) content is comparable with other published non-woods and the lignin (5.67%) content is favourably the lowest. In addition, the hot water and 1% NaOH solubilities are (3.83%) and (19.64%) respectively. SEM images show that cogon grass fibres contained abundance and long fibres which provide good strength of the produced handsheet. Based on the chemical and surface morphological properties analyses, cogon grass is a good alternative fibre resource especially for pulp and paper making industries.

This paper describes simulation of combustion characteristics under high ambient and high injection of biodiesel combustion by using CFD simulation. Diesel engine performance and emissions is strongly couple with fuel atomization and spray processes, which in turn are strongly influenced by injector flow dynamics. The principal objective of this research is to seek the effect of temperature and pressure on the spray characteristics, as well as fuel-air mixing characteristics. Experiments were performed in a constant volume chamber at specified ambient gas temperature and pressure. This research was continued with injecting diesel fuel into the chamber using a Bosch common rail system. Direct photography technique with a digital camera was used to clarify the real images of spray pattern, liquid length and vapor penetration. The method of the simulation of real phenomenon of diesel combustion with optical access rapid compression machine is also reviewed and experimental results are presented. The liquid phase of the spray reaches a maximum penetration distance soon after the start of injection, while the vapor phase of the spray continues to penetrate downstream. The condition to which the fuel is affected was estimated by combining information on the block temperature, ambient temperature and photographs of the spray. The increases in ambient pressure inside the chamber resulting in gain of spray area and wider spray angle. Thus predominantly promotes for a better fuel-air mixing. All of the experiments will be conducted and run by using CFD. The simulation will show in the form of images.

Langmuir-Blodgett technique was applied to build optically homogeneous film of functionalized multi-walled carbon nanotubes (MWCNTs) on paper substrate. The palladium (Pd) nanoparticles were drop-casted onto MWCNTs network films before being exposed in hydrogen (H2) gas molecules environment under vacuum and atmospheric pressure at room temperature. The results demonstrate that the functionalized MWCNTs dispersed with Pd nanoparticles show good H2 sensing response on paper substrate where the sensitivity of around 10 % was recorded at only 2 minutes exposure time.

Magnetic stripe cards and magnetic recording paper are commonly used in credit cards, identity cards, and transportation tickets. Barium ferrite was used to prepare magnetic inks and the magnetic ink was coated onto the paper substrate to obtain the magnetic papers. The crystal structure of barium ferrite was characterized by X-ray diffraction (XRD) and the magnetic property of barium ferrite was tested by vibrating sample magnetometer (VSM) The performance of the magnetic recording paper and the surface morphology of the coating magnetic layer were also characterized. The results show that the magnetic ink based on barium ferrite with the formula of 41wt% of the barium ferrite powder, 14wt% of polyurethane, 36wt% of solvent and 9wt% of PVP has good printing characteristics and the magnetic recording papers have good performance.

The novel flexible pressure sensor with skin-like stretchability and sensibility has attracted tremendous attention in academic and industrial world in recent years. And it also has demonstrated great potential in the applications of electronic skin and wearable devices. It is significant and challenging to develop a highly sensitive flexible pressure sensor with a simple, low energy consuming and low cost method. In this paper, the silver nanowires (AgNWs) as electrode material were synthesized by polyol process. The polydimethylsiloxane (PDMS) was chosen as a flexible substrate and polyimide (PI) film as dielectric layer. The AgNWs based electrode was prepared in two methods. One is coating the AgNWs on photographic paper followed by in situ PDMS curing. Another one is suction filtration of the AgNWs suspension followed by glass slide transfer and PDMS curing. Then the capacitive pressure sensor was packaged in a sandwich structure with two face to face electrodes and a PI film in the middle. The sensitivity of the sensor as well as the micro-structure of the electrodes was compared and studied. The results indicate that the roughness of the electrode based on AgNWs/PDMS micro-structure plays an important role in the sensitivity of sensor. The as-prepared flexible pressure sensor demonstrates high sensitivity of 0.65kPa-1. In addition, the fabrication method is simple, low energy consuming and low cost, which has great potential in the detection of pulse, heart rate, sound vibration and other tiny pressure.

A huge number of available Life Cycle Assessment (LCA) studies have shown that data availability for paper products is enormous regionally. In Malaysia, LCA practices are considered uncommon attributed to the lack of data availability and LCA practitioner itself. Therefore, a cradle to cradle study has been carried out to determine the potential impacts arise from the recycled paper production in Malaysia. LCA methodology used in this study including goal and scope definition, inventory analysis (LCI), impact assessment (LCIA) and interpretation is based on ISO 14040 and ISO 14044 framework. A series of input-output data collection has been carried out and the collected data was calculated by using Simapro software followed by data evaluation using Eco-indicator 99 method. The results showed that the most significant impacts generated throughout the system were fossil fuel and resources at the midpoint and endpoint level respectively. This can be attributed to a high consumption of chemicals and energy in the pulp and paper manufacturing process. As a consequence, a comprehensive practice in mill specifically on chemicals and resources include water and energy consumption, as well as the waste management and recycling system needs to be addressed explicitly to mitigate the relevant impacts.

Noise is one of the problems that often occur in urban areas due to the traffic condition. Noise in a building design depends on the choice of materials as sound absorbers. The type of sound dampening material that already exists is a porous material, a resonator, and a panel. The material often used as an absorber is porous materials, because it is relatively cheaper and lighter, especially to reduce the noise in the narrow spaces such as housing and offices. Various substitutes are made from cheap materials, such as the use of recycled materials of egg tray paper with the size of 40 x 40 centimeters. This is a quantitative research that will measure the place of egg tray paper in reducing noise, using a Sound Level Meter. The use of the egg tray paper is able to show an adequate acoustic quality as noise absorbers, with the average value of NR 22-26 dB.

There are too many waste that has the capability in undermine the environment, including paper waste. The unused paper waste collected from one office only could reach two tons a year. To decrease the possibility of paper waste in ruining the environment, it can be recycled to be any usable things. One example is recycle the paper waste into paper brick as building material. Before the brick can be used, it needs to be tested whether it can create a thermal comfort or not. So the objectives of the research are to find the ability of paper brick in create thermal comfort, and compare it with the red brick that is commonly used by people. The method used in this research is field measurement using model and hygrometer as a tool. The result of the research is that the paper brick can create a thermal comfort in some hours of a day. But it turns out that it is not better than the red brick in decreasing the outside temperature. The temperature inside the building with a red brick is lower that the temperature in the building with the paper brick.

As an important document for the description and communication of transport policies, transport white papers have drawn special attention in western countries. This paper studies European transport white papers with the aim to explore their merits for reference. Firstly, the paper reviews the chronological development of European transport white papers to give a holistic view. Then, three European transport white papers that have critical historical meanings are analyzed in details, inspecting their issue background and policy objectives. Moreover, the features of European transport white papers are summarized, which include the concentration on chief problem, thorough action plan and flexible content system. These features deserve learning for other authorities when developing transport white papers.

This paper aimed at the quality of the transparent paper package, developed a machine vision detection system and successfully applied it in production line. A variety of transparent paper defects are detected out. This system makes the transparent paper packing quality b improved and provides good reference for the application of the technology of machine vision detection.

Along with the widespread use of food wrap paper, it is very important to discuss the migration of lead in paper. The migration of lead from six kinds of food wrap papers under different temperatures (5 °C, 25°C, 35°C, 60°C and 85°C) were investigated by using water as an imitation in this paper. It was found that the initial migration rate was affected by the sizing degree of paper, but the final migration ratio was mainly decided by initial concentration of lead in paper, and the migration rate increased with the increasing of temperature.

As a kind of environmentally friendly material, microfibrillated cellulose (MFC) has the following advantages: renewable raw materials, easy recycling, biodegradable, safety and so on. It can be combined with antibacterial agents to prepare the antibacterial packing materials for food. In this paper, the nano-ZnO was modified by titanate coupling agent TM-38s at first,determines the best dosage of TM-38 is 3% in the modification process,the dosage of the isopropyl alcohol for 40ml,improving its dispersibility. And then added in the MFC suspension to formulate the antibacterial coating for antibacterial coated paper preparation. The changes of antibacterial properties of the paper before and after coating were investigated in this study. The results showed that the paper had a significant antibacterial activity to e. coli and staphylococcus aureus (the antibacterial circle was bigger than 15 mm).When the nano-ZnO dosage was 2.5wt%, the antibacterial properties of the coated paper could reach the best situation. Application of the antibacterial caoated paper to the food packaging could restrain and kill the microorganisms on the food surface effectively, prolong the shelf life of food, and improve the food safety.

In order to improve the printing quality, 10 kinds of different manufacturers, different gram weight offset paper are used in this title, measure the quantitative, thickness, gloss, K&N values, and roughness of those paper. Print papers through IGTAIC2-5, calculate the ink transfer rate and transfer parameters. Using SPSS to analysis relationship between the performance of paper and ink transfer rate, transfer parameter b, k, f ' by using mathematical methods. The research results show that the performance of the paper affect ink transfer rate and transfer parameter b, k, f '; The tightness, roughness ,glossiness and K&N value have notable effect on the ink transfer rate and transfer parameter k; transfer parameter b, f ' has no remarkable influence.

In order to investigate the influence of coating layer characteristics on the dynamic permeability and printing of ink-jet paper, coating was prepared by the precipitated calcium carbonate (PCC) and white latex used as bottom coating (recipe label:A,B),and coating formula was made by silica (SiO2) and polyvinyl alcohol used as surface coating (recipe label:a,b,c).Then paper were coated respectively on single bottom, single surface and multilayer. Then the dynamic permeability and printing of ink-jet paper were analyzed systematically. The results showed that whether single layer or multilayer, the values of Ct, Ci were minimum when the ration of pigment and adhesive was 70:30, because the hole diameter of the coating layer was smallest, and the absorption was strongest, so the dynamic permeability was best, and the ability of ink absorption was best, color density and tone reproducibility were best. It concluded that when the proportion of SiO2 and PVA was 70:30, the dynamic permeability and printing ability of ink-jet paper were relative better.

The organic contaminants which in the printing inks or varnish of paper (board) surface can migrate via paper (board) to the packed food (simulants) in the form of gases and do harm to the health of consumers.To predict the concentration of them in the packed food (simulants) at a given storage time, the migration model of them was established. For a sheet of paper consists of several layers of interlaced fibers, the organic contaminants can be traped by the fibers when they penetrate to the inner layers by the capillaries in the printing process, so the linear coefficient of retardation Rm was introduced to modify the Fick’s Laws, and the diffusion equationwas gotten. It demonstrated that the values of Rm increase with the increasing of molecular weight of surrogates, and decrease with the increasing of migration temperature. And the diffusion coefficients Dp of phenol, 2, 6-Dissopropyl naphthalenes (2,6-DIPNs) and dibuthyl phthalate (DBP) in the kraft paper board were range from 10-5 to 10-4 at 75°C and 100°C. Then the migration model was validated by migration experimental tests, and the model described the profile of the experimental values very well.

The bonding mechanism between water-based UV curable ink and active groups on paper’s fiber during curing process was studied in this paper. Low viscosity water-based UV-cured resin was synthesized by epoxy resins, epoxy diluent, acrylic acid and maleic anhydride in the presence of catalyst. The viscosity of the synthesis system and synthetic products were significantly reduced when epoxy diluent was added to replace parts of the epoxy resin. Epoxy diluent was very useful in reducing the viscosity of the product, but over-dose would have negative effects on the quality of the cured film. The water-based epoxy acrylate prepolymer was used as the substitution for the ink to investigate the binding mechanism between the active groups of prepolymer and fiber under UV irradiation. The prepolymer and photoinitiator were mixed and the mixture was diluted to an appropriate viscosity by a small amount of water, then printed on the paper by the method of analog printing and curred by UV curing machine. The printed paper was used to extract lignin by enzymatic/mild acidolysis. FT-IR was used to characterize the changes of the active groups in lignin. The results showed that the changes of active groups in lignin were founded in the existence of ultraviolet and photoinitiator, which consistent with the change of double bonds in prepolymer. The free radicals produced by photoinitiator in curing process not only promoted the double bonds to polymerize, but also accelerated the active groups of lignin binding. Experiments show that chemical bonds exist between them.

The composite SiOx/polymer films are deposited as a top-coatings onto the paper substrates by radio frequency (RF) reactive magnetron co-sputtered two targets, silica and dicyclopentadiene dioxide cured with maleic anhydride (DCPD/MA).The samples prepared by changing PSiO2 /PDCPD/MA, the ratio of RF powers density delivered to the individual target from 0.1 to 10 so as to prepare different SiOx content coatings. The wettability, mechanical properties, color reproduction printability, chemical characterization of the coatings are discussed in this paper, using contact angle measurements, electronic tensile testing machine, off-set printing test and FTIR. The static contact angle of water ranges from 129.7 to 90.7 o and tensile performance has improved significantly as the ratio of RF powers density change from 0.1 to 10. The ink density and depth of color during off-set printing are visually improved by using papers with hydrophobic surfaces coated composite films.

The gray balance in color printing is the basis of accurate color reproduction. In essence, it reproduces accurate gray value by using color ink. In this paper, we choose three kinds of papers with different whiteness, use the same ink -jet printer and the same ink to print gray balance test charts and measure neutral gray blocks in order to draw the gray balance curves. Experimental result shows that the characteristic of gray balance curves obtained by this method are different from those obtained by traditional method. Especially in bright tone, the gray balance data gets a better adjustment, which can improve the exact color reproduction in ink-jet printing.

The experiment studied effects of paper on the height and glossiness of UV ink-jet 3D printing. The results showed that there all existed penetrations between the 1st ink layer and three kinds of paper, the bigger the roughness and bulk of paper were, the larger the penetration was, and penetration between the 1st ink and paper was obviously larger than that between two ink layers. Penetration between two ink layers was stable, almost not affected by paper. The bigger the roughness and bulk of paper were, the smaller the glossiness of ink layer was. There appeared directional ink strips on ink layer on three kinds of paper, beginning from the 3rd ink layer, there also appeared ink pits on ink layer on paper whose roughness and bulk were the biggest, which showed printer precision was also an important factor for the glossiness, apart from paper. Thus, the tight and smooth paper should be selected in UV ink-jet 3D printing. Before printing, pretreatment should be done to exclude the influence of the 1st ink layer and the ink strips.

Most paper-based 3D color printers are plagued by the problem of slow printing speed, which is caused by the double-sided coloration for A4 office paper during the printing process. In order to resolve this issue, we propose a new fast and reliable coloration algorithm using geometric information in STL file, given the existing slicing methods. During the entire process, the colored surface is determined by D value that represents the positive or negative slope of layer in the 3D model after slicing. Colored inks with corresponding permeability are used to print single-sided or double-sided to accelerate the printing speed. For the given 3D models, the efficiency of the speedup is discussed and qualitatively analyzed. The results show that the proposed algorithm can increase the printing speed of paper-based 3D color printers, based on the existing materials and apparatus, at a lower cost than the common approaches.

By using printability tester for printing on ordinary white cardboard and light beam hologram paper, measuring spectral information and chrominance information of the two samples, and then perform spectral fitting by analyses their color characteristics, The aim of this research was to propose one method for color calculation of printing on light beam hologram papers, according to the color information of ordinary white cardboard.

Green and environmental protection has become a theme of contemporary furniture design. As a unique furniture material, paper has characteristics like wide source, easy processing, non-toxic and pollution-free. It has been used in the development and design of furniture. Paper furniture has broad application prospects.

This paper defines the efficiency similarity of different motor driving devices. Based on the efficiency function characteristics which can be approximately considered a concave, non-negative function through the origin, we present a kind of optimal control method for a felt driven by three different motors in paper machine. It gives the minimum total power consumption. The optimal control method is to keep the same torque rate for each motor driving device. This method is independent of the linearity or nonlinearity of the system and has no need for the system’s state equation or transfer function. Since the shapes of efficiency functions in nature are similar, the conclusion can also be applied to the energy optimization of other general devices.

This paper mainly discuss the effect of beating on OCC pulp fiber morphology and paper physical Strength. After the treatment with PFI, the beating degree were ranged from 25 ° SR rises from 56 °SR, the fiber morphologies were greatly changed, and appeared splitting and brooming. Physical results showed that beating can improve strength properties of OCC pulp in the proper degree, 46°SR was the best result in this study.

This paper has a brief introduction to a algorithm that can automatically identify the defective cutting region when automatic paper cutter does quality analysis. The algorithm analyzed the characteristics of processed shear mark image,detected defects,found a critical point of defective part ,then a unique regional recognition algorithm was developed based on the basis of the general processing algorithm. The algorithms can pinpoint the region that cutting defects exist according to the coordinates of critical point accurately, improve the efficiency of quality analysis, and also has stated that image processing is available in the regional recognition of automatic paper cutter.

Noise pollution is a workplace hazard which causes loss of hearing, depending on the sound pressure level and duration of exposure. Because duration of exposure is usually uncontrollable, sound absorbers are used to reduce the value of sound pressure level. A common method to reduce noise is to use porous sound absorbers made out of mineral wools or glass fibres. However, these materials pose health risks and are non-recyclable. This project aimed to fabricate a sound absorber using recycled paper which is in the form of egg cartons as an alternative to the abovementioned fibres. Paper fibres posses high fibre porosity and can be manufactured in a manner which the properties can be easily controlled, making them ideal to be made into sound absorbers. Furthermore, they are biodegradable, do not pose health risks and can be manufactured into different shapes easily. Recycled paper was first turned into pulp, blended and poured into moulds. Different amounts of pulp was compressed until the sample size was approximately 20 mm thick and then dried in a furnace dryer at 600C for 12 hours. The samples were tested using a two-microphone, transfer function impedance tubes according to the ISO 10534-2 standard. Its porosity was determined using a modified wash basin method. The results indicate that the optimum panel has an average noise reduction coefficient, (NRC) of 0.50, which qualifies it to be used as a sound absorbing material. It also encounters its maximum value of 0.98 which occurred at the 1575-1675 Hz range. When compared to other materials, recycled paper has similar properties as coir fibre and is quite comparable to other commercial sound absorbers at the same thickness.

Peer review is a new phenomenon in the process of internationalization of academic journals, but also a worldwide problem. In this paper, the development and practical application of peer review system are sort out, which are based on objective data research of domestic and international academic journals; the problems of network online published papers in practice are analyzed and explored by modern advanced network technology as the application tool, and how scientific orientation are they to play an effective role. The purpose of paper is in order to ensure the impartiality of the academic council, spread rapidly and use information resources, and further promote to enhance the overall level of academic journals.

According to the features of paper currency CIS image, the fuzzy set theory is initial used to improve the contrast of banknote target and background, paper money’s edge pixels are obtained by scanning, and then the sub-pixel edges are fitted by least square method; in the fitting process, the error threshold method is applied for eliminating noisy edge points, then slope correction of paper money is carried out according to the angle of sub-pixel edge line and the note area is extracted, finally, fuzzy enhancement is used for the extracted image again. Experiments show that, this method has good versatility, high accuracy and strong anti-interference ability, it can even extract the paper currency area effectively in the edge deterioration and unfilled corner condition, and the enhanced image is in favor of subsequent paper currency recognition.

Moisture has a detrimental effect on oil-paper insulation life by lowering electrical breakdown strength. How does the space charge behavior of the oil-paper insulation system consisted by oil gap and oil immersed insulation pressboard with different moisture content? The space charge characteristics of the mixed insulation consisted of oil gap and pressboard with three moisture content were investigated using the PEA measurement system. The space charge accumulation behaviors at the interface between oil gap and pressboard were analyzed. The distortion of the electrical field in the oil gap and pressboard was also analyzed. Results show that there are many charges injected into the oil and the pressboard. The charges accumulated at the interface between oil gap and pressboard. The charges accumulated in the mixed insulation system become less with the moisture content increased. The difference of the electric field strength in the oil gap and pressboard become smaller with the moisture content increased.

The paper currency image recognition method based on Gabor filter set is discussed in this paper. According to the paper currency image features, the suitable parameters of Gabor filter set are selected for the extraction of paper currency characteristics, the multi-scale and multi-directional texture characteristics of paper currency image are gotten; then the texture images are meshed, and the row and column projection sum of grid pixels' average grey are calculated, finally, the template match method based on grid projection characteristics is used for paper currency recognition. Experiments show that, this method has strong anti-interference ability, it can raise the recognition rate of old or dirty paper currency greatly, and it costs little time.

A novel method has been developed to detect 1,2-benzisothiazolin-3-one (BIT) in paper for food packaging by hydrothermal extraction coupled with fluorescence spectroscopy in paper for food package. Parameters affecting fluorescence intensity have been evaluated, including the pH of solvents and the effect of surfactants. It turned out to be that fluorescent spectroscopy was a sensitive and easy method to determine BIT in paper package. The regression equation obtained was liner, and the correction coefficient was 99.9%, the limit detection (LOD) was 25.3μg/L, method detection limit (MDL) was 0.25mg/kg, which turned out that this method was sensitive and precise to determine BIT in food package.

This paper focuses on scraps of paper splicing recovery issues. To deal with complex scraps restoration problem, first the image should be changed as pixel grey level binary image, generating binary matrix, and then classify the scraps using SOM neural network data and feature comparison method. Combining with the Euclidean distance discriminant method, we match the scraps of paper with same edges and obtain a complete stitching schematic finally.

The restoration of regular paper fragments can be solved by edge matching. Edge matching is based primarily on the length and location of the break in writing, however, it is possible that the edges of some regular paper fragments are blank. And so the error of restoration is the inevitable. In this case, it needs manual intervention based on the article content and then eliminate errors. Prior to the establishment of a mathematical model, there is a need for binarization of regular paper fragments with Matlab, then establish vector space model and construct edge contrast matrix, get the order after the Q cluster analysis of fragments. Finally the original picturecan be obtained through splicing and restoring in the order.

When we think of paper-folding, we usually think first of the name that is usually associated with it: origami. But in the field of architecture, origami is more than just imagining an animal or flower which is what this word usually brings to mind. In architecture, we extend the meaning to take in the real essence of the word – that of great structural and constructional loads. The basic unit of origami – the fold – allows us to start manipulating space and even to create space itself. Paper-folding, with its spatial modelling potential, is to three-dimensionality what drawing is to two-dimensionality. It is after all an ancient Japanese art which encapsulates the advantages of intuitive thinking and fast modelling, once the basic elements of folding are known. Heino Engel (2001) in his book “Structural Systems”, describes intensive studies on types of structures which derive from this systematization. And the architect Ming Tang often uses structures in his projects which clearly originate in the concept of origami, and he correlates these structures with sustainable materials. The architect Michael Hansmeyer manages to incorporate all the beauty of the action of folding with the help of a computer, where the final result is a shape that approaches a real application at an architectural level. Over time, there have been numerous people who have found a relationship between the harmony and proportions of paper-folding and their own studies and projects. What is missing is a single point where clear concepts on the possibilities of folding and the results of those who have experimented with it can be brought together. This cataloguing, which is being carried out in this Master’s dissertation, is intended to be a contribution to the design method in architecture, through which the architect may achieve spatial dexterity over a piece of paper.

In order to realize precise control of the vertical inverting feeding of paper, the paper proposes the scheme to analyse the accuracy. Based on the geometric constraint relations of the feeding device, the position constraint equation of the device is established, together with the speed-acceleration formula; and the relationship between the paper inverting deviation angle and its drop height is obtained using the general equation of dynamics of the horizontal projectile motion as vertical inverting accuracy analysis of the device. The results of the study show that the precise control of the vertical inverting feeding of paper can be realized through the control of the angle.

In this study, four types of Waste Paper Sludge Ash (WPSA) were explored for use as Supplementary Cementitious Materials (SCM) in binary system. The WPSA use varies in particle size range and surface area however similar in chemical composition. At first stage, Ordinary Portland Cement (OPC) was replaced by WPSA at 5% mass to mass basis as blended cement. Four size of WPSA was prepared which are unsieve, retained at 63μm, retained at 45μm and pan. WPSA blended cement (WPSABC) was introduced from the four size of WPSA that prepared earlier. Water to cement ratio selected was 0.50 and it keep constant at all type of blended cement. When compared with the control mix, result shows that hydration kinetics is affected by the particle size of WPSA. Pan WPSA has slightly higher peak of hydration kinetics and compressive strength of blended cement. At second stage, Pan WPSA was selected to undergo the further investigation on its performance. Pan WPSABC were prepared at replacement level of 5%, 10%, 15% and 20%, mass to mass basis. Same method and w/c ratio was used and compared with control mix. From the result, it is found that the peak for rate of heat evolution of Pan WPSABC occur earlier and slightly lower as compared to OPC. Pan WPSA also achieved it optimum strength at 5% replacement level which is more than control mix.

Compared with the lithography and traditional technology, ink-jet printing technology has huge advantages such as reducing costs, improving production efficiency and reducing environment damage. The silver nanoparticles conductive ink used as core material in ink-jet printing technology has been greatly developed. At present, the conductive inks for printed circuit usually has high sintering temperature, low adhesion, poor mechanical properties, high cost, which limit the further industrial application. In this paper, nano silver pulp was prepared through liquid phase reduction method, and a self-made protective agent ensured that the particle size distribution of silver particles is about 5nm. The above silver pulp was dispersed in the organic resin to get conductive ink with 20% (wt%) silver content. Under 170°Csintering, the electrical conductivity of the ink layer was 1.15×104S/m.