Search

The perceptual experience of the transition between coupled rooms remains a little investigated area of research. This paper presents a pipeline for auralising the transition between coupled rooms, utilising a time-varying partitioned convolution for fast position-dependent switching between spatial room impulse responses (SRIRs) and parametric binaural rendering over highly acoustically transparent headphones, with in-situ calibration to the corresponding real-world acoustics. The system is verified by an in-situ listening test with both real and virtual stimuli, conducted in six degrees-of-freedom virtual reality with three-dimensional visuals from measured room models. Results show that the auralisation is rated as highly natural, equalling the naturalness of the corresponding real world auditory stimuli. This pipeline is therefore appropriate for testing of coupled room transition algorithms and SRIR interpolation techniques, as well as non-in-situ testing.

© 2017 Elsevier B.V. Background and purpose: To perform a quantitative analysis of the accuracy and precision of Kilovoltage Intrafraction Monitoring (KIM) six degree-of-freedom (6DoF) prostate motion measurements during treatments. Material and methods: Real-time 6DoF prostate motion was acquired using KIM for 14 prostate cancer patients (377 fractions). KIM outputs the 6DoF prostate motion, combining 3D translation and 3D rotational motion information relative to its planning position. The corresponding groundtruth target motion was obtained post-treatment based on kV/MV triangulation. The accuracy and precision of the 6DoF KIM motion estimates were calculated as the mean and standard deviation differences compared with the ground-truth. Results: The accuracy ± precision of real-time 6DoF KIM−measured prostate motion were 0.2 ± 1.3° for rotations and 0.1 ± 0.5 mm for translations, respectively. The magnitude of KIM-measured motion was well-correlated with the magnitude of ground-truth motion resulting in Pearson correlation coefficients of ≥0.88 in all DoF. Conclusions: The results demonstrate that KIM is capable of providing the real-time 6DoF prostate target motion during patient treatments with an accuracy ± precision of within 0.2 ± 1.3° and 0.1 ± 0.5 mm for rotation and translation, respectively. As KIM only requires a single X-ray imager, which is available on most modern cancer radiotherapy devices, there is potential for widespread adoption of this technology.

Purpose To establish a streamlined end‐to‐end test of a 6 degrees‐of‐freedom (6DoF) robotic table using a 3D printed phantom for periodic quality assurance. Methods A 3D printed phantom was fabricated with translational and rotational offsets and an imbedded central ball‐bearing (BB). The phantom underwent each step of the radiation therapy process: CT simulation in a straight orientation, plan generation using the treatment planning software, setup to offset marks at the linac, registration and corrected 6DoF table adjustments via hidden target test, delivery of a Winston‐Lutz test to the BB, and verification of table positioning via field and laser lights. The registration values, maximum total displacement of the combined Winston‐Lutz fields, and a pass or fail criterion of the laser and field lights were recorded. The quality assurance process for each of the three linacs were performed for the first 30 days. Results Within a 95% confidence interval, the overall uncertainty values for both translation and rotation were below 1.0 mm and 0.5° for each linac respectively. When combining the registration values and other uncertainties for all three linacs, the average deviations were within 2.0 mm and 1.0° of the designed translation and rotation offsets of the 3D print respectively. For all three linacs, the maximum total deviation for the Winston‐Lutz test did not exceed 1.0 mm. Laser and light field verification was within tolerance every day for all three linacs given the latest guidance documentation for table repositioning. Conclusion The 3D printer is capable of accurately fabricating a quality assurance phantom for 6DoF positioning verification. The end‐to‐end workflow allows for a more efficient test of the 6DoF mechanics while including other important tests needed for routine quality assurance.

For spacecraft in low-perigee orbits, atmospheric drag presents one of the largest uncertainties in dynamics modeling. These uncertainties are particularly relevant to small satellites, which often fly in the LEO regime and produce control forces and torques comparable in magnitude to drag. In this study, a six degrees-of-freedom orbital dynamics model with drag perturbations is developed, and several applications of the model are investigated. The model is used to evaluate differential drag dynamics for the MR and MRS SAT microsatellite pair, and the implications to collision avoidance and end-of-life procedures are discussed. Preliminary propellant usage estimates for the mission are also generated. A modified method for determining ballistic coefficient using relative satellite navigation data is introduced and compared to previous methods.

Target rotation can considerably impact the delivered radiotherapy dose depending on the tumour shape. More accurate tumour pose during radiotherapy treatment can be acquired through tracking in 6 degrees-of-freedom (6 DoF) rather than in translation only. A novel real-time 6 DoF kilovoltage intrafraction monitoring (KIM) target tracking system has recently been developed. In this study, we experimentally evaluated the accuracy and precision of the 6 DoF KIM implementation. Real-time 6 DoF KIM motion measurements were compared against the ground truth motion retrospectively derived from kV/MV triangulation for a range of lung and prostate tumour motion trajectories as well as for various static poses using a phantom. The accuracy and precision of 6 DoF KIM were calculated as the mean and standard deviation of the differences between KIM and kV/MV triangulation for each DoF, respectively. We found that KIM is able to provide 6 DoF motion with sub-degree and sub-millimetre accuracy and precision for a range of realistic tumour motion.

We report on the development of an all-interferometric optomechatronic sensor for the detection of multi-degrees-of-freedom displacements of a remote target. The prototype system exploits the self-mixing technique and consists only of a laser head, equipped with six laser sources, and a suitably designed reflective target. The feasibility of the system was validated experimentally for both single or multi-degrees-of-freedom measurements, thus demonstrating a simple and inexpensive alternative to costly and bulky existing systems.

The research presented in this thesis describes a substantial part of the design of a prototypical surgical training simulator. The results are intended to be applied in future simulators used to educate and train surgeons for bone milling operations. In earlier work we have developed a haptic bone milling surgery simulator prototype based on three degrees-of-freedom force feedback. The contributions presented here constitute an extension to that work by further developing the haptic algorithms to enable six degrees-of-freedom (6-DOF) haptic feedback. Such feedback is crucial for a realistic haptic experience when interacting in a more complex virtual environment, particularly in milling applications.The main contributions of this thesis are:The developed 6-DOF haptic algorithm is based on the work done by Barbic and James, but differs in that the algorithm is modified and optimized for milling applications. The new algorithm handles the challenging problem of real-time rendering of volume data changes due to material removal, while fulfilling the requirements on stability and smoothness of the kind of haptic applications that we approach. The material removal algorithm and the graphic rendering presented here are based on the earlier research. The new 6-DOF haptic milling algorithm is characterized by voxel-based collision detection, penalty-based and constraint-based haptic feedback, and by using a virtual coupling for stable interaction.Milling a hole in an object in the virtual environment or dragging the virtual tool along the surface of a virtual object shall generate realistic contact force and torque in the correct directions. These are important requirements for a bone milling simulator to be used as a future training tool in the curriculum of surgeons. The goal of this thesis is to present and state the quality of a newly developed 6-DOF haptic milling algorithm. The quality of the algorithm is confirmed through a verification test and a face validity study performed in collaboration with the Division of Orthopedics at the Karolinska University Hospital. In a simulator prototype, the haptic algorithm is implemented together with a new 6-DOF haptic device based on parallel kinematics. This device is developed with workspace, transparency and stiffness characteristics specifically adapted to the particular procedure. This thesis is focuses on the 6-DOF haptic algorithm. QC 20120226

In this paper a design is presented for a precision MEMS-based six degrees-of-freedom (DOFs) manipulator. The purpose of the manipulator is to position a small sample (10 μm × 20 μm × 0.2 μm) in a transmission electron microscope. A parallel kinematic mechanism with slanted leaf-springs is used to convert the motion of six in-plane electrostatic comb-drives into six DOFs at the end-effector. The manipulator design is based on the principles of exact constraint design, resulting in a high actuation compliance (flexibility) combined with a relatively high suspension stiffness. However, due to fabrication limitations overconstrained design has been applied to increase the stiffness in the out-of-plane direction. The result is a relatively large manipulator stroke of 20 μm in all directions combined with a high first vibration mode frequency of 3.8 kHz in relation to the used area of 4.9 mm × 5.2 mm. The motion of the manipulator is guided by elastic elements to avoid backlash, friction, hysteresis and wear, resulting in nanometer resolution position control. The fabrication of the slanted leaf-springs is based on the deposition of silicon nitride (SixNy) on a silicon pyramid, which in turn is obtained by selective crystal plane etching by potassium hydroxide (KOH). The design has been analyzed and optimized with a multibody program using flexible beam theory. A previously developed flexible beam element has been used for modeling the typical relatively large deflections and the resulting position-dependent behavior of compliant mechanisms in MEMS. The multibody modeling has been verified by FEM modeling. Presently only parts of the manipulator have been fabricated. Therefore, a scaled-up version of the manipulator has been fabricated to obtain experimental data and to verify the design and modeling.