Search

The presented study focused on developing an innovative decision-making framework to select the best renewable-power-plant technologies, considering comprehensive techno-economic and environmental variables. Due to the favourable conditions, Australia was selected as the case study. A fuzzy-logic method and analytical hierarchy process were applied to prioritize different renewable-energy power plants. The techno-economic factors included levelized cost of energy, initial cost, simple payback time, and operation and maintenance costs along with environmental factors including carbon payback time, energy payback time and greenhouse-gas emissions were used to rank the power plants. The results showed that the capital cost and simple payback time had the highest priority from an economic point of view. In comparison, greenhouse-gas emissions and carbon payback time were the dominant environmental factors. The analysis results provided economic and environmental priority tables for developing different power plants in the current state and a future scenario by 2030. The fuzzy results and pairwise composite matrix of alternatives indicated that the onshore wind, offshore wind, single-axis tracker polycrystalline photovoltaic, single-axis tracker monocrystalline photovoltaic, fix-tilted polycrystalline photovoltaic and fix-tilted monocrystalline photovoltaic scored the highest in the current state. In contrast, by 2030, the single-axis tracker photovoltaic power plants will be the best choice in the future scenario in Australia. Finally, the results were used and analysed to recommend and suggest several policy implementations and future research studies.

The share of biofuels in the transportation sector is increasing. Previous studies revealed that the use of biofuels decreases the size of particles (which is linked to an increase in particulate toxicity). Current emission regulations do not consider small particles (sub-23 nm); however, there is a focus in future emissions regulations on small particles. These and the fact that within cold-start emissions are higher than during the warmed-up operation highlight the importance of a research that studies particulate matter emissions during cold-start. This research investigates the influence of biofuel on PN and PM concentration, size distribution, median diameter and cumulative share at different size ranges (including sub-23 nm and nucleation mode) during cold-start and warm-up operations using diesel and 10, 15 and 20% mixture (coconut biofuel blended with diesel). During cold-start, between 19 and 29% of total PN and less than 0.8% of total PM were related to the nucleation mode (sub-50 nm). Out of that, the share of sub-23 nm was up to 9% for PN while less than 0.02% for PM. By using biofuel, PN increased between 27 and 57% at cold-start; while, the increase was between 4 and 19% during hot-operation. The median diameter also decreased at cold-start and the nucleation mode particles (including sub-23 nm particles) significantly increased. This is an important observation because using biofuel can have a more adverse impact within cold-start period which is inevitable in most vehicles’ daily driving schedules.

Four types of fuels blended with diesel in scaling proportion were used in a diesel engine to generate 13 different soot samples. The samples were characterised for their thermal-induced oxidation process with DSC and TGA from which the mass loss during each of three phases and 6 critical temperatures was obtained per sample. With the same samples, soot chemical structure was characterised by Raman, XPS and TEM. This analysis provided information on different carbon chemical structures, O/C ratio on the sample surface, and nanostructure (fringe length and tortuosity). It was observed that generally for oxygenated fuel blends, the soot samples are more reactive, have more O functional groups on the carbon layer edge plane and have smaller polyaromatic layer size than reference diesel soots, while aromatic fuel blends show the opposite trends. However, the trend was not distinctive for all the samples analysed. Nevertheless, the two groups of data are highly correlated which implies that the chemical structure is the underlying reason dominating the soot reactivity. Specifically, the soot samples with more O functional groups and/or C–C bonds on the edge plane, are more reactive, they lose more mass at the lower temperature range and require lower temperature to initiate oxidation.

The concentration, nature, and persistence of particulate matter (PM)-bound reactive oxygen species (ROS) are of significant interest in understanding how atmospheric pollution affects health. However, the inherent difficulties in their measurement, particularly regarding the so-called "short-lived" ROS, have limited our understanding of their persistence and concentrations in the atmosphere. This paper aims to address this limitation through the analysis of PM-bound ROS measurements from the Particle Into Nitroxide Quencher (PINQ) system at an atmospheric monitoring site in the city of Heshan, Guangdong Province, China. The measured daily average and standard deviation for the measurement period was 0.050 ± 0.017 nmol·m-3. The averaged measured concentration of ROS per mass of PM and standard deviation was 0.0012 ± nmol·mg. The dataset was also correlated with standard pollutants, and a simplified model was constructed to separate the contributions of short-lived (t1/2 = 5 min) and long-lived (t1/2 ∼ infinity) ROS to total concentration using ozone, carbon monoxide, and PM mass. This showed that the short-lived ROS contribute an average of 33% of the daily PM-bound ROS burden over the measurement period, up to 52% of daily average on elevated days, and up to 71% for hourly averages. These results highlight the need for accurate measurements of short-lived ROS and provide the starting point for a general model to predict PM-bound ROS concentrations using widely available standard pollutants for future epidemiological research.

Diesel emissions contain high levels of particulate matter (PM) which can have a severe effect on the airways. Diesel PM can be effectively reduced with the substitution of diesel fuel with a biofuel such as vegetable oil. Unfortunately, very little is known about the cellular effects of these alternative diesel emissions on the airways. The aim of this study was to test whether coconut oil substitution in diesel fuel reduces the adverse effect of diesel emission exposure on human bronchial epithelial cells. Human bronchial epithelial cells were cultured at air-liquid interface for 7 days and exposed to diesel engine emissions from conventional diesel fuel or diesel fuel blended with raw coconut oil at low (10%), moderate (15%) and high (20%) proportions. Cell viability, inflammation, antioxidant production and xenobiotic metabolism were measured. Compared to conventional diesel, low fractional coconut oil substitution (10% and 15%) reduced inflammation and increased antioxidant expression, whereas higher fractional coconut oil (20%) reduced cell viability and increased inflammation. Therefore, cellular responses after exposure to alternative diesel emission are dependent on fuel composition.

The share of biofuels in the fuel market has increased over the last several decades. This is related to their potential to reduce the emissions including particulate matter. It has been frequently reported that the fuel oxygen content is the main reason for the reduction in particulate matter emissions. To understand the effect of fuel oxygen content on morphology and nanostructure characteristics of soot particles, different fuels such as diesel, coconut biodiesel and triacetin were tested in a diesel engine with various mixing proportions. The fuel blending was done in such a way that overall oxygen content of fuel was kept in range of 0% to 14% (wt.%). The soot particles were sampled from the engine exhaust system and analysed with a transmission electron microscope (TEM) at low and high spatial resolution. The TEM images were post-processed with the help of an in-house developed image analysis program to determine the morphology and nanostructure characteristics. The results show that oxygenated fuel blends emit smaller sized soot particles forming compact aggregates. The investigation of the internal structure of soot particles show disordered arrangement of graphene layers for fuels up to 11.01% fuel oxygen content (pure biodiesel); however, the opposite trend was observed for fuel blends with triacetin which could be related to the presence of oxygen in a different chemical functional group.

The chemical composition and evolution of secondary organic aerosol (SOA) in the atmosphere represents one of the largest uncertainties in our current understanding of air quality. Despite vast research, the toxicological mechanisms relating to adverse human health effects upon exposure to particulate matter are still poorly understood. Particle-bound reactive oxygen species (ROS) may substantially contribute to observed health effects by influencing aerosol oxidative potential (OP). The role of radicals in both the formation and aging of aerosol, as well as their contribution to aerosol OP, remains highly uncertain. The profluorescent spin trap BPEAnit (9,10-bis(phenylethynyl)anthracenenitroxide), previously utilized to study combustion-generated aerosol, has been applied to provide the first estimate of particle-bound radical concentrations in SOA. We demonstrate that SOA from different atmospherically important VOC precursors have different particle-bound radical concentrations, estimated for the ozonolysis of α-pinene (0.020 ± 0.0050 nmol/μg), limonene (0.0059 ± 0.0010 nmol/μg), and β-caryophyllene (0.0025 ± 0.00080 nmol/μg), highlighting the potential importance of OH-initiated formation of particle-bound organic radicals. Additionally, the lifetime of particle-bound radical species in α-pinene SOA was estimated, and a pseudo-first-order rate constant of k = 7.3 ± 1.7 × 10–3 s–1 was derived, implying a radical lifetime on the order of minutes.

In numerous epidemiological studies, exposure to particulate matter (PM) has been associated with negative health outcomes. It has been established so far that the detrimental health effects of particles cannot be explained by a single parameter, such as particle mass, as the complexity of chemical composition and reactivity of particles are not always represented by the mass loadings. The oxidative potential (OP) of aerosol particles represents a promising indicator of their potential toxicity. To develop strategies and regulations at improving the air quality, an increasing number of studies are focused on the application of source apportionment (SA) of PM., while a limited number of SA investigations have been applied to OP. In this review previous research of SA of atmospheric PM oxidative potential and proposed guidelines for future studies are summarized. Most of the research studies were carried out in an urban area and focused on PM2.5, while few studies examined other PM fractions. It was noted that the three dominant contributors to OP were biomass burning (9-97%), secondary aerosols (6-67%) and traffic/vehicles (16-88%). The presence of other factors that contributed to the increase of OP to a lesser extent depended on the location and season. Further, a considerable discrepancy in the contribution of various OP vs. PM sources was discovered using SA models. Because of this, the use of SA is not equivalent when considering the mass of PM and its toxicity.

A comprehensive analysis of combustion behaviour during cold, intermediately cold, warm and hot start stages of a diesel engine are presented. Experiments were conducted at 1500 rpm and 2000 rpm, and the discretisation of engine warm up into stages was facilitated by designing a custom drive cycle. Advanced injection timing, observed during the cold start period, led to longer ignition delay, shorter combustion duration, higher peak pressure and a higher peak apparent heat release rate (AHRR). The peak pressure was ~30% and 20% and the AHRR was ~2 to 5% and ±1% higher at 1500 rpm and 2000 rpm, respectively, during cold start, compared to the intermediate cold start. A retarded injection strategy during the intermediate cold start phase led to shorter ignition delay, longer combustion duration, lower peak pressure and lower peak AHRR. At 2000 rpm, an exceptional combustion behaviour led to a ~27% reduction in the AHRR at 25% load. Longer ignition delays and shorter combustion durations at 25% load were observed during the intermediately cold, warm and hot start segments. The mass fraction burned (MFB) was calculated using a single zone combustion model to analyse combustion parameters such as crank angle (CA) at 50% MFB, AHRR@CA50 and CA duration for 10–90% MFB.

This study investigates the morphology and nanostructure of soot particles during cold-start and hot-start engine operation of a diesel engine using oxygenated fuels. The soot samples were analysed using transmission electron microscopy. The oxygen content in the fuel was varied between 0 and 12%. The results showed that the primary particles during cold-start have significantly smaller size when compared to hot-start engine operation. The addition of oxygenated fuels also resulted in smaller sized primary particles. Smaller radius of gyration and higher fractal dimension of soot aggregates during cold-start would mean smaller aggregate size with a more compact structure. Shorter fringes with a higher inter-fringe spacing for cold-start would mean lower graphitisation of soot particles that could be related to higher oxidation reactivity of soot particles.

Atmospheric semi-volatile organic compounds (SVOCs) are complex in their chemical and toxicological characteristics with sources from both primary combustion emissions and secondary oxygenated aerosol formation processes. In this study, thermal desorption of PM2.5 in association with online measurement of reactive oxygen species (ROS) was carried out to study the role of SVOCs in its gas-particle partitioning. The mass concentrations of PM2.5, black carbon (BC) and p-PAHs downstream of a thermodenuder were measured online at different temperature settings (25, 50, 100, and 200 °C) to characterize PM physico-chemical properties. While the mass concentrations of PM2.5 and p-PAHs reduced to ∼34% at 200 °C compared to that in ambient temperature, BC mass concentration has decreased by 30% at the highest temperature. Furthermore, the submicron particle size distribution showed reduced particle number concentration in Aitken mode at 200 °C heating. The ROS, measured by Particle-into-Nitroxide-Quencher, also showed reduction and followed a similar trend with PM measurements, where the total ROS decreased by 12%, 31%, and 53% at 50 °C, 100 °C, and 200 °C, respectively, compared to the ambient sample. When a HEPA filter was included in the upstream of samples, 39% of gas phase ROS reduction was observed at 200 °C. This provided a good estimate of the contribution of SVOCs in ROS production in PM2.5, where decreased SVOCs concentration at 200 °C increased the percentage of particle surface area. This concludes that the surface chemistry of these organic coatings on the particles is important for assessing the health impacts of PM.

The International Agency of Research on Cancer identifies high-temperature frying, which features prominently in Chinese cooking, as producing group 2A carcinogens. This study simultaneously characterized particulate and gaseous-phase cooking emissions, monitored their reactive oxygen species (ROS) concentrations, and evaluated their impact on genetic damage and expression in exposed human bronchial epithelial cells. Five types of edible oil, three kinds of seasonings, and two dishes were assessed. Among tested edible oils, heating of soybean oil released the largest particle number concentration (2.09 × 1013 particles/(g cooking material and oil)·h) and volatile organic compounds (VOCs) emissions (12103.42 μg/(g cooking material and oil)·h). Heating of lard produced the greatest particle mass concentration (0.75 mg/(g cooking material and oil)·h). The main finding was that sunflower and rapeseed oils produced the highest ROS concentrations (80.48 and 71.75 nmol/(g cooking material and oil)·h, respectively). ROS formation most likely occurred during the autoxidation of both polyunsaturated and monounsaturated fatty acids. Among all the tested parameters, only ROS concentrations exhibited consistency with cell viability and showed significant correlations with the expression levels of CYP1A1, HIF-1a, and especially with IL-8 (the marker for oxidative stress within the cell). These findings indicate that ROS concentration is potentially a suitable metric for direct assessment of exposure levels and potential toxicity.

This study investigates the effect of engine temperature during cold start and hot start engine operation on particulate matter emissions and engine performance parameters. In addition to a fundamental study on cold start operation and the effect of lubricating oil during combustion, this research introduces important knowledge about regulated particulate number emissions and particulate size distribution during cold start, which is an emerging area in the literature. A further aspect of this work is to introduce waste lubricating oil as a fuel. By using diesel and two blends of diesel with 1 and 5% waste lubricating oil in a 6-cylinder turbocharged engine on a cold start custom test, this investigation studied particle number (PN), friction losses and combustion instability with diesel and waste lubricating oil fuel blends. In order to understand and explain the results the following were also studied: particle size distribution and median diameter, engine oil, coolant and exhaust gas temperatures, start of injection, friction mean effective pressure (FMEP), mechanical efficiency, coefficient of variation (CoV) of engine speed, CoV of indicated mean effective pressure (IMEP) and maximum rate of pressure rise were also studied. The results showed that during cold start the increase in engine temperature was associated with an increase in PN and size of particles, and a decrease in FMEP and maximum rate of pressure rise. Compared to a warmed up engine, during cold start, PN, start of injection and mechanical efficiency were lower; while FMEP, CoV of IMEP and maximum rate of pressure rise were higher. Adding 5% waste lubricating oil to the fuel was associated with a decrease in PN (during cold start), decreased particle size, maximum rate of pressure rise and CoV of IMEP and was associated with an increase in PN and nucleation mode particles (during hot start) and FMEP.

Using waste paper as fuel for domestic heating is a beneficial recycling option for small island developing states where there are lacks of resources for energy and waste treatment. However, there are concerns about the impact of air pollutants emitted from the burning of the self-made paper briquettes as household air pollution is recognised as the greatest environmental risk for human. In this study, combustion tests were carried out for paper briquettes made in one Pacific island and three commercial fuels in Australia including wood briquettes, kindling firewood and coal briquettes in order to: 1) characterise the emissions of three criteria air pollutants including particulate matters, CO and NOx including their emission factors (EF) from the tested fuels; and 2) compare the EFs among the tested fuels and with others reported in the literature. The results showed that waste paper briquettes burned quickly and generated high temperature but the heat value is relatively low. Paper briquettes and coal briquettes produced higher CO concentration than the others while paper briquettes generated the highest NOx level. Only PM2.5 concentration emitted from paper briquettes was similar to kindling firewood and lower than wood briquettes. Burning of paper briquettes and wood briquettes produced particulate matter with large average count median diameter (72 and 68 nm) than coal briquette and kindling firewood (45 and 51 nm). The EFs for CO, NOx and PM2.5 of paper briquettes were within the range of EFs reported in this study as well as in the literature. Overall, the results suggested that using paper briquettes as fuel for domestic heating will not likely to generate higher level of three major air pollutants compared to other traditional fuels.

Mosquito-repellent incense is popular for dispelling mosquitos indoors in Asia, Africa and South America. However, the released large amounts of particulate and gaseous pollutants have a negative effect on human health. We conducted real-time measurements in laboratory chamber to characterize the particulate matter, volatile organic species (VOCs), reactive oxygen species (ROS) released from the Disc and Liquid mosquito-repellent incenses using. And further to evaluate the secondary organic aerosol (SOA) formation potential indoors attributed to the main VOCs species and the health exposure risk. Results show that the disk type produces more particles but less VOCs. The particle number concentration produced by the disc and the liquid types were 130085 part/cm3 and 7963 part/cm3, respectively. The former one concentrated at the size bins below 100 nm, in comparison with the latter one mainly between 100 and 500 nm. Burning disk type produced particles carrying much higher oxidative potential (OP) 0.0430 nmol/mg. The VOCs species produced by the disc and liquid types were mainly VOC to m/z 79(benzene) and VOC to m/z 33(methanol), and the corresponding benzene concentration were 40.7 ppb and 58.6 ppb, respectively, and the methanol concentration was 26.3 ppb and 35.2 ppb, respectively. SOA formation rate related to benzene of liquid type using was larger compared to disk type, which was 0.015 mg/(m3s) and 0.012 mg/(m3s), respectively. The health risk assessment coefficient of the disc and liquid types were 6.2×10−5 and 9.1×10−5, respectively, both exceeding the limit of 1×10−6, indicating mosquito-repellent incenses is harmful to human health.

Cooking fume produced by oil and food at a high temperature releases large amount of fine particulate matter (PM) which have a potential hazard to human health. This chamber study investigated particle emission characteristics originated from using four types of oil (soybean oil, olive oil, peanut oil and lard) and different kinds of food materials (meat and vegetable). The corresponding emission factors (EFs) of number, mass, surface area and volume for particles were discussed. Temporal variation of size-fractionated particle concentration showed that olive oil produced the highest number PM concentration for the entire cooking process. Multiple path particle dosimetry (MPPD) model was performed to predict deposition in the human respiratory tract. Results showed that the pulmonary airway deposition fraction was the largest. It was also found that particles produced from olive oil led to the highest deposition. We strongly recommend minimizing the moisture content of ingredients before cooking and giving priority to the use of peanut oil instead of olive oil to reduce human exposure to PM.

© 2019 Elsevier Ltd Rising concerns over environmental and health issues of internal combustion engines, along with growing energy demands, have motivated investigation into alternative fuels derived from biomasses, such as biodiesel. Investigating engine and exhaust emission behaviour of such alternative fuels is vital in order to assess suitability for further utilisation. Since many parameters are relevant, an effective multivariate analysis tool is required to identify the underlying factors that affect the engine performance and exhaust emissions. This study utilises principal component analysis (PCA) to present a comprehensive correlation of various engine performance and emission parameters in a compression ignition engine using diesel, biodiesel and triacetin. The results show that structure-borne acoustic emission is strongly correlated with engine parameters. Brake specific NOx, primary particle diameter and fringe length increases by increasing the rate of pressure rise. Longer ignition delay and higher engine speeds can increase the nucleation particle emissions. Higher air-fuel equivalence ratio can increase the oxidative potential of the soot by increasing fringe distance and tortuosity. The availability of oxygen in the cylinder, from the intake air or fuel, can increase soot aggregate compactness. Fuel oxygen content reduces particle mass and particle number in the accumulation mode; however, they increase the proportion of oxygenated organic species. PCA results for particle chemical and physical characteristics show that soot particles reactivity increases with fuel oxygen content.

In the transportation sector, the share of biofuels such as biodiesel is increasing and it is known that such fuels significantly affect NOx emissions. In addition to NOx emission from diesel engines, which is a significant challenge to vehicle manufacturers in the most recent emissions regulation (Euro 6.2), this study investigates NO2 which is a toxic emission that is currently unregulated but is a focus to be regulated in the next regulation (Euro 7). This manuscript studies how the increasing share of biofuels affects the NO2, NOx, and NO2/NOx ratio during cold-start (in which the after-treatment systems are not well-effective and mostly happens in urban areas). Using a turbocharged cummins diesel engine (with common-rail system) fueled with diesel and biofuel derived from coconut (10 and 20% blending ratio), this study divides the engine warm-up period into 7 stages and investigates official cold- and hot-operation periods in addition to some intermediate stages that are not defined as cold in the regulation and also cannot be considered as hot-operation. Engine coolant, lubricating oil and exhaust temperatures, injection timing, cylinder pressure, and rate of heat release data were used to explain the observed trends. Results showed that cold-operation NOx, NO2, and NO2/NOx ratio were 31–60%, 1.14–2.42 times, and 3–8% higher than the hot-operation, respectively. In most stages, NO2 and the NO2/NOx ratio with diesel had the lowest value and they increased with an increase of biofuel in the blend. An injection strategy change significantly shifted the in-cylinder pressure and heat release diagrams, aligned with the sudden NOx drop during the engine warm-up. The adverse effect of cold-operation on NOx emissions increased with increasing biofuel share.

Carbonyl compounds are important constituents of photochemical smog and important precursors of photochemical smog formation. In order to investigate concentrations and types of carbonyls generated during cooking process, the influence of cooking styles, food materials, oil types and purification facilities were investigated. Silica cartridge impregnated with 2,4-dinitrophenylhydrazine (2,4-DNPH) and high performance liquid chromatography (HPLC) were adopted for collecting and analyzing samples. Results showed that the emission factors (EFs) of carbonyls (C1-C8) produced from cooking emissions varied within the range of 0.669–1.596 μg/kg. In relation to cooking styles, Barbecue (1.596 μg/kg) > Frying (1.530 μg/kg) > Teppanyaki (1.229 μg/kg) > Stir-frying (0.699 μg/kg), while C1-C3 carbonyls accounted for over 85% for the carbonyls concentrations. Regarding the food materials, generally, carbonyl emissions from meat dishes were greater than for non-meat dishes. Among different oil types used, cooking with sunflower oil resulted in the highest carbonyl emissions. In addition, carbonyls produced from frying carried the highest health risk. The high-voltage electrostatic methodology applied to remove carbonyls did not show as efficient for this purpose. Formaldehyde was found to be the largest contributor to ozone formation potential (OFP).

Cooking oil fumes (COF) contain massive particulate matter. Chronic exposure to cooking oil fumes constitutes a health hazard. This study aims to measure the COF exposure level during a typical Chinese domestic cooking process and evaluate whether a short-term exposure at this level entails deleterious cardiopulmonary, inflammatory health effects and oxidative stress. 6 young healthy students were recruited to conduct a contrast experiment in a kitchen chamber. Every participant cooked successively three typical Chinese dishes twice a day for two consecutive days, during which the particle mass and number concentration in the breathing zone were monitored. A slot around the pan supplied air at varied rates during cooking, resulting in altered exposure dose. Before the experiment and after their cooking, the levels of biomarkers were measured including 8 biomarkers for lung function, fractional exhaled nitric oxide for respiratory inflammation, blood pressure for cardiovascular risks and three biomarkers in urine for oxidative stress. PM2.5 concentration and particle number concentration in 0.02–6.25 μm were 10.97 ± 9.53 mg/m3 and 23.12 ± 18.27 103/cm3 in the breathing zone under normal ventilation condition and might triple under poor ventilation. Health measurements showed that forced vital capacity and vital capacity declined significantly after the fourth cooking process. Peak expiratory flow rose significantly after the third cooking. Meanwhile, forced expiratory flows at 25% of the vital capacity also increased significantly after both the third and fourth cooking. However, a single short-term exposure to COF of around 20 min does not explicitly entail significant health risks.

Chinese-style cooking often involves volatilization of oils which can potentially produce a large number of pollutants, which have adverse impact on environment and human health. Therefore, we have reviewed 75 published studies associated with research topic among Mainland China, Hong Kong and Taiwan, involving studies on the roles of food ingredients and oil type, cooking style impacting on generated pollutants, and human health. The highest concentration occurred including: 1) when peat, wood, and raw coal were used in stoves; 2) olive oil was adopted; 3) cooking with high temperatures; and 4) without cleaning technology. We conclude that PM concentrations for cooking emissions were between 0.14 and 24.46mg/cm3. VOC concentrations varied from 0.35 to 3.41mg/m3. Barbeque produced the greatest mass concentrations compared to Sichuan cuisine, canteen and other restaurants. The PAHs concentration emitted from the exhaust stacks, dining area and kitchen ranged from 0.0175μg/m3 to 83μg/m3. The largest amount of gaseous pollutants emitted was recorded during incomplete combustion of fuel or when a low combustion efficiency (CO2/ (CO+CO2)

Highlights • Gas phase emissions can be potentially as hazardous as the particle phase ones. • Gas phase diesel exhaust has a stronger inflammation effect on human lung cells. • Fuel oxygen content is negatively correlated to the gas phase OP. • Total VOC content is not correlated to the gas phase OP. • Idling produces emissions with the highest OP in the gas phase. Abstract The oxidative potential (OP) of the gas phase is an important and neglected aspect of environmental toxicity. Whilst prolonged exposure to particulate matter (PM) associated reactive oxygen species (ROS) have been shown to lead to negative health effects, the potential for compounds in gas phase to cause similar effects is yet to be understood. In this study we describe: the significance of the gas phase OP generated through vehicle emissions; discuss the origin and evolution of species contributing to measured OP; and report on the impact of gas phase OP on human lung cells. The model aerosol for this study was exhaust emitted from a Euro III Common-rail diesel engine fuelled with different blends of diesel and biodiesel. The gas phase of these emissions was found to be potentially as hazardous as the particle phase. Fuel oxygen content was found to negatively correlate with the gas phase OP, and positively correlate with particle phase OP. This signifies a complex interaction between reactive species present in gas and particle phase. Furthermore, this interaction has an overarching effect on the OP of both particle and gas phase, and therefore the toxicity of combustion emissions.

The large (26-fold over the past 25 years) increase in the on-road vehicle fleet in China has raised sustainability concerns regarding air pollution prevention, energy conservation, and climate change mitigation. China has established integrated emission control policies and measures since the 1990s, including implementation of emission standards for new vehicles, inspection and maintenance programs for in-use vehicles, improvement in fuel quality, promotion of sustainable transportation and alternative fuel vehicles, and traffic management programs. As a result, emissions of major air pollutants from on-road vehicles in China have peaked and are now declining despite increasing vehicle population. As might be expected, progress in addressing vehicle emissions has not always been smooth and challenges such as the lack of low sulfur fuels, frauds over production conformity and in-use inspection tests, and unreliable retrofit programs have been encountered. Considering the high emission density from vehicles in East China, enhanced vehicle, fuel and transportation strategies will be required to address vehicle emissions in China. We project the total vehicle population in China to reach 400-500 million by 2030. Serious air pollution problems in many cities of China, in particular high ambient PM2.5 concentration, have led to pressure to accelerate the progress on vehicle emission reduction. A notable example is the draft China 6 emission standard released in May 2016, which contains more stringent emission limits than those in the Euro 6 regulations, and adds a real world emission testing protocol and a 48-h evaporation testing procedure including diurnal and hot soak emissions. A scenario (PC[1]) considered in this study suggests that increasingly stringent standards for vehicle emissions could mitigate total vehicle emissions of HC, CO, NOX and PM2.5 in 2030 by approximately 39%, 57%, 59% and 79%, respectively, compared with 2013 levels. With additional actions to control the future light-duty passenger vehicle population growth and use, and introduce alternative fuels and new energy vehicles, the China total vehicle emissions of HC, CO, NOX and PM2.5 in 2030 could be reduced by approximately 57%, 71%, 67% and 84%, respectively, (the PC[2] scenario) relative to 2013. This paper provides detailed policy roadmaps and technical options related to these future emission reductions for governmental stakeholders.

To estimate the oxidative potential (OP) of particulate matter (PM), two commonly used cell-free, molecular probes were applied: dithiothreitol (DTT) and dichloro-dihydro-fluorescein diacetate (DCFH-DA), and their performance was compared with 9,10-bis (phenylethynyl) anthracene-nitroxide (BPEAnit). To the best of our knowledge, this is the first study in which the performance of the DTT and DCFH has been compared with the BPEAnit probe. The average concentrations of PM, organic carbon (OC) and elemental carbon (EC) for fine (PM2.5) and coarse (PM10) particles were determined. The results were 44.8 ± 13.7, 9.8 ± 5.1 and 9.3 ± 4.8 µg·m−3 for PM2.5 and 75.5 ± 25.1, 16.3 ± 8.7 and 11.8 ± 5.3 µg·m−3 for PM10, respectively, for PM, OC and EC. The water-soluble organic carbon (WSOC) fraction accounted for 42 ± 14% and 28 ± 9% of organic carbon in PM2.5 and PM10, respectively. The average volume normalized OP values for the three assays depended on both the sampling periods and the PM fractions. The OPBPEAnit had its peak at 2 p.m.; in the afternoon, it was three times higher compared to the morning and late afternoon values. The DCFH and BPEAnit results were correlated (r = 0.64), while there was no good agreement between the BPEAnit and the DTT (r = 0.14). The total organic content of PM does not necessarily represent oxidative capacity and it shows varying correlation with the OP. With respect to the two PM fractions studied, the OP was mostly associated with smaller particles.

This manuscript details the application of a profluorescent nitroxide (PFN) for the online quantification of radical concentrations on particulate matter (PM) using an improved Particle Into Nitroxide Quencher (PINQ). A miniature flow-through fluorimeter developed specifically for use with the 9,10-bis(phenylethynyl)anthracene-nitroxide (BPEAnit) probe was integrated into the PINQ, along with automated gas phase corrections through periodic high efficiency particle arrestor (HEPA) filtering. The resulting instrument is capable of unattended sampling and was operated with a minimum time resolution of 2.5 min. Details of the fluorimeter design and examples of data processing are provided, and results from a chamber study of side-stream cigarette smoke and ambient monitoring campaign in Guangzhou, China are presented. Primary cigarette smoke was shown to have both short-lived (t1/2 = 27 min) and long-lived (t1/2 = indefinite) PM-bound reactive oxygen species (ROS) components which had previously only been observed in secondary organic aerosol (SOA).

Waste management cost for Australia is increasing every year, and thus, it is important to find alternative ways to use the waste. For example, essential oil has a significant waste stream that can be utilized in vehicles of their producers. However, some of the essential oils contain oxygen which considerably affects engine performance, emission, and combustion characteristics of diesel engines. Thus, this research paper will try to evaluate the essential oils as a replacement of diesel fuel to operate a multicylider diesel engine. For this study, two essential oils are selected which contain different oxygenated functional groups, tea tree oil (5.4% oxygen) and eucalyptus oil (8.4% oxygen), with an aim to evaluate the effect of these functional groups on engine performance and emission parameters. These oils were blended with neat diesel (0% oxygen) to obtain a blend cotaining 2.2% oxygen by weight. The blends produced similar brake power; however, brake-specific fuel consumption (BSFC) increased for eucalyptus oil blends (2.4–3.7%) and tea tree oil blends (3.9–5.3%). Essential oil–diesel blends resulted in less CO and increased NOX emission, produced similar peak pressure, and indicated mean effective pressure. The results then lead to the conclusion that oxygenated essential oils can have a role to reduce dependency of agricultural sector on diesel in the near future.

Almost one third of the world's population uses biomass fuel for cooking and heating, contributing significantly to exposure from indoor air pollution. Common biomass fuels include wood, dung and crop residues. Burning of biomass fuels in poorly ventilated indoor household areas leads to the emission of toxic particulate matter and volatile gasses which, when inhaled, result in inflammation and oxidative stress in the lungs. This toxicity can, like that of cigarette smoking, lead to the development of chronic obstructive pulmonary disease (COPD), which is characterized by exertional breathlessness, cough and sputum production, with the presence of chronic airflow obstruction on spirometry. Inflammation and oxidative stress have been identified as key cellular and molecular mechanisms in the pathogenesis of COPD. Cigarette smoke exposure is considered to be the main risk factor for COPD. Spirometry testing is recognized as the gold standard for diagnosing and grading the severity of airflow obstruction.

Rising pollution levels resulting from vehicular emissions and the depletion of petroleum-based fuels have left mankind in pursuit of alternatives. There are stringent regulations around the world to control the particulate matter (PM) emissions from internal combustion engines. To this end, researchers have been exploring different measures to reduce PM emissions such as using modern combustion techniques, after-treatment systems such as diesel particulate filter (DPF) and gasoline particulate filter (GPF), and alternative fuels. Alternative fuels such as biodiesel (derived from edible, nonedible, and waste resources), alcohol fuels (ethanol, n-butanol, and n-pentanol), and fuel additives have been investigated over the last decade. PM characterization and toxicity analysis is still growing as researchers are developing methodologies to reduce particle emissions using various approaches such as fuel modification and after-treatment devices. To address these aspects, this review paper studies the PM characteristics, health issues, PM physical and chemical properties, and the effect of alternative fuels such as biodiesel, alcohol fuels, and oxygenated additives on PM emissions from diesel engines. In addition, the correlation between physical and chemical properties of alternate fuels and the characteristics of PM emissions is explored.

Soot particles, mainly coming from fuel combustion, affect climate forcing through absorbing light and also result in adverse human health outcomes. Though biodiesel or additives blending with diesel was considered environmentally friendly, the understanding on absorbing and oxidative capacity of soot emitted from them are still unclear. The water-soluble organic carbon (WSOC) content, surface chemical structure, light absorption and oxidative potential (OPDTT) of soot from biodiesel/diesel and chemicals/diesel blends were investigated utilizing total organic carbon analyzer, X-ray photoelectron spectrometer, ultraviolet–visible spectrophotometry and dithiothreitol (DTT) assay. The differences and correlations between soot properties were statistically analyzed. Chemicals/diesel blends soot owned significantly higher WSOC content, ratio of mass absorbing efficiency (MAE) in 250 and 365 nm (E2/E3), OPDTT, and higher surface carbonyl content. Coconut biodiesel/diesel blends soot contained evidently higher aromatic carbon–oxygen single bond (Ar_C–O) content, and higher MAE365. The individual comparison of biodiesel/diesel blends showed 20% coconut biodiesel blend owned the lowest WSOC, E2/E3 and OPDTT, while highest Ar_C–O and MAE365, representing strongest absorbing properties. Association analysis showed OPDTT was significantly positively correlated with WSOC. Further, the evident negative correlation between MAE365 and OPDTT was observed. Our results showed coconut biodiesel/diesel blends soot induced lower levels of oxidative potential, whereas absorption of light was higher, which have far reaching consequences on climate forcing. Therefore, it is important to evaluate the balance point between light-absorbing properties and oxidative potential, under the wide use of biodiesel.

Emissions from ships at berth are small compared to the total ship emissions; however, they are one of the main contributors to pollutants in the air of densely-populated areas, consequently heavily affecting public health. This is due to auxiliary marine engines being used to generate electric power and steam for heating and providing services. The present study has been conducted on an engine representative of a marine auxiliary, which was a heavy duty, six-cylinder, turbocharged and after-cooled engine with a high pressure common rail injection system. Engine performance and emission characterisations during cold start are the focus of this paper, since cold start is significantly influential. Three tested fuels were used, including the reference diesel and two IMO (International Maritime Organization) compliant spiked fuels. The research engine was operated at a constant speed and 25% load condition after 12 h cooled soak. Results show that during cold start, significant heat generated from combustion is used to heat the engine block, coolant and lubricant. During the first minute, compared to the second minute, emissions of particle number (PN), carbon monoxide (CO), particulate matter (PM), and nitrogen oxides (NO x) were approximately 10, 4, 2 and 1.5 times higher, respectively. The engine control unit (ECU) plays a vital role in reducing engine emissions by changing the engine injection strategy based on the engine coolant temperature. IMO-compliant fuels, which were higher viscosity fuels associated with high sulphur content, resulted in an engine emission increase during cold start. It should be taken into account that auxiliary marine diesel engines, working at partial load conditions during cold start, contribute considerably to emissions in coastal areas. It demonstrates a need to implement practical measures, such as engine pre-heating, to obtain both environmental and public health advantages in coastal areas.

INTRODUCTION: Chronic obstructive pulmonary disease (COPD) will be the third leading cause of death world-wide by 2020. Prolonged exposure to particulate matter is associated with COPD progression and mortality. Diesel emissions are a major contributor to particulate matter pollution. In this study we test a therapeutic antioxidant, N-acetylcysteine (NAC), for its ability to protect bronchial epithelial cells (pHBECs) from patients with COPD from adverse effects of diesel emission exposure. METHODS: pHBECs from patients with or without COPD were cultured at air-liquid interface (ALI). Cells were exposed to diesel emissions for 30 min with or without 3-h post-exposure treatment with 5 mM N-acetylcysteine (NAC). Filtered laboratory air was tested as a negative control. Cell responses (cell viability, inflammation and oxidative stress) and gene expression profiles for intracellular and immune signaling were assessed. RESULTS: Diesel emissions exposure increased IL-8 secretion and production, antioxidant production, and cytochrome P450 1a1 (CYP1a1) mRNA expression and suppressed superoxide dismutase-1 (SOD1) mRNA expression in bronchial epithelial cells from COPD patients. Treatment with N-acetyl cysteine attenuated the suppression of SOD1. Nanostring gene expression profiling of the filtered air controls showed COPD epithelial cells have increased expression of MHC class II and an interferon signaling profile. CONCLUSIONS: This study indicates that bronchial epithelial cells from COPD patients may be vulnerable to diesel emission exposure due to reduced antioxidant capacity, and elevated CYP1a1 mRNA expression. NAC did not appear to offer protection. Future research will be needed to explore other means of recovering oxidant capacity in COPD airways.

NOx emissions from diesel engines are a concern from both environmental and health perspectives. Recently this attention has targeted cold-start emissions highlighting that emission after-treatment systems are not effective in this period. Using a 6-cylinder, turbocharged, common-rail diesel engine, the current research investigates NOx emissions during cold-start using different engine performance parameters. In addition, it studies the influence of waste lubricating oil on NOx emissions introducing it as a fuel additive (1 and 5% by volume). To interpret the NOx formation, this study evaluates different parameters: exhaust gas temperature, engine oil temperature, engine coolant temperature, start of injection/combustion, in-cylinder pressure, heat release rate, maximum in-cylinder pressure and maximum rate of pressure rise. This study clarified how cold-start NOx increases as the engine is warming up while in general cold-start NOx is higher than hot-start. Results showed that in comparison with warmed up condition, during cold-start NOx, maximum in-cylinder pressure and maximum rate of pressure rise were higher; while start of injection, start of combustion and ignition delay were lower. During cold-start increased engine temperature was associated with decreasing maximum rate of pressure rise and peak apparent heat release rate. During cold-start NOx increased with temperature and it dropped sharply due to the delayed start of injection. This study also showed that using waste lubricating oil decreased NOx and maximum rate of pressure rise; and increased maximum in-cylinder pressure. NOx had a direct correlation with the maximum rate of pressure rise; and an inverse correlation with the maximum in-cylinder pressure.

The airborne particulate matter (PM) is known to cause adverse pulmonary and cardiovascular health effects. This study investigated the diurnal characteristics of PM induced PM-bound ROS from real time measurements in typical roadside and urban background sites in Hong Kong, and identified potential influencing factors to its variation in atmosphere. A nitroxide probe (BPEAnit) was employed in the real-time measurement of separate PM and gas phase induced reactive oxygen species (ROS) with a Particle-into-Liquid-Sampler. Measurements were carried in 2 h intervals over a 24 h period, and repeated for 6 days at each site. The total ROS (particle + gas phase) measurements resulted in multiple peaks at 08:00, 16:00 and 20:00 h time periods at background site, compared to non-intermittent decrease/increase trends at roadside. The total ROS generation was noted significantly higher by 50–100% (n = 6 p < .05) at roadside compared to the background site. While the contribution of PM2.5- and gas phase-induced ROS to the total ROS was on average 48 ± 8% and 52 ± 8% across 24 h at background site, the ratio of gas phase-induced ROS increased to 79 ± 4% and that of particle phase decreased to 21 ± 4% at roadside site. The total ROS well correlated with black carbon (BC) and particle-bound PAHs (p-PAHs), which are 4–8 fold and 10–20 fold higher at roadside than background. The ratio of p-PAHs/BC was high at roadside during peak hours compared to late nights suggesting fresh PM may have induced more total ROS generation compared to aged aerosols using this specific ROS probe.

Presented in this paper is an in-depth analysis of the impact of engine start during various stages of engine warm up (cold, intermediate, and hot start stages) on the performance and emissions of a heavy-duty diesel engine. The experiments were performed at constant engine speeds of 1500 and 2000 rpm on a custom designed drive cycle. The intermediate start stage was found to be longer than the cold start stage. The oil warm up lagged the coolant warm up by approximately 10 &deg, C. During the cold start stage, as the coolant temperature increased from ~25 to 60 &deg, C, the brake specific fuel consumption (BSFC) decreased by approximately 2% to 10%. In the intermediate start stage, as the coolant temperature reached 70 &deg, C and the injection retarded, the indicated mean effective pressure (IMEP) and the brake mean effective pressure (BMEP) decreased by approximately 2% to 3%, while the friction mean effective pressure (FMEP) decreased by approximately 60%. In this stage, the NOx emissions decreased by approximately 25% to 45%, while the HC emissions increased by approximately 12% to 18%. The normalised FMEP showed that higher energy losses at lower loads were most likely contributing to the heating of the lubricating oil.

Urban airborne particles contain a wide spectrum of components, known to have harmful effects on human health. This study reports a detailed investigation of fine particulate matter (PM2.5), chemical content and oxidative potential derived from two different urban environments. During summer and winter, 20-day campaigns were conducted at Belgrade city center (urban-background site – UB) and Bor (urban-industrial site – UI). Using various analytical techniques, carbonaceous compounds, water-soluble inorganic ions, major and trace elements were determined, while the oxidative potential of PM2.5 was estimated by dichloro-dihydro-fluorescein diacetate (DCFH-DA) assay (OPDCFH values). The mean PM2.5 concentrations in both urban environments were above the recommended daily value, and the dominant PM2.5 mass contributor was organic matter (29–55%). The OC/EC ratio was significantly higher at UB site during winter, which was an indication of a considerable contribution of secondary organic carbon to the overall organic carbon (OC). Water-soluble organic carbon (WSOC) was also higher at UB than at UI site, and it probably came from the same sources as OC. In general, the different partition of secondary organic aerosol (SOA) in warm and cold periods affected the number of organic components. Sulfates and nitrates were the most abundant ions at both sites and they counted approximately 40% (summer) and 50% (winter) of total ions. Further, the concentrations of the most elements, particularly some potentially carcinogenic elements such as As, Cd and Pb were significantly higher at UI, due to the emissions from the copper smelter complex in the vicinity. The mean OPDCFH values were similar during the summer at both sampling sites, whereas a statistically significant difference between sites was noticed in favor of UB environment in winter.

Metallic composition of diesel particulate matter, even though a relatively small proportion of total mass, can reveal important information regarding engine conditions, fuel/lubricating oil characteristics and for health impacts. In this study, a detailed investigation into the metallic elemental composition at different particle diameter sizes has been undertaken. A bivariate statistical analysis was performed in order to investigate the correlation between the metallic element, measured engine performance and engine emission variables. Major sources of metallic elements in the emitted particles are considered in this study, including the fuel and lubricating oil compositions, engine wear emissions and metal-containing dust in the ambient air. Metallic solid ultrafine-particles (Dp 100 nm). Calculated correlation matrices show a clear effect of engine load conditions and fuel S contents on particle number and mass emissions.

Over the years, oxygenated fuels such as biodiesel and alcohol fuels have been useful in reducing particulate matter (PM) emissions of diesel engines. The presence of oxygen in the fuel impacts the soot oxidation process and thus the morphology and nanostructural characteristics of soot particles change. The nanostructure characteristics of soot particles hold an importance for their oxidation reactivity and toxicity. Higher reactivity and exposure of soot particles to oxygen will affect the regeneration and filtration efficiency of diesel particulate filters. In this study, we investigate the impact of oxygen functional groups on morphology and nanostructure of soot particles by blending different types of essential oil in diesel. The test fuels were prepared by mixing orange oil, tea tree oil, eucalyptus oil and coconut biodiesel to keep an overall oxygen content of 0 and 2.2%. Transmission electron microscopy was used to investigate the physical changes in the nanostructure of soot particles. The primary particle diameter decreases, and fractal dimension of soot aggregates increases for oxygenated fuels. Microscopy reveals that the arrangement of carbon lamellae within the soot particles changes significantly with use of oxygenated as observed by the changes in fringe length, fringe tortuosity and fringe separation distance. Lower fringe length, higher fringe tortuosity and fringe separation distance shows disordered arrangement of carbon layers with more possibility of oxygen attack. The different structural characteristics for oils having same oxygen content shows that formation and structure of soot particles strongly depend upon chemical structure and composition of the fuel.

Presence or generation of reactive oxygen species (ROS) on/by particulate matter (PM) have been implicated in PM-induced health effects. Methodologies to quantify ROS concentrations vary widely both in detection and collection methods. However, there is currently an increasing emphasis on rapid collection and measurement due to observations of short half-live ROS. To address this problem, this manuscript details the design and characterization of a novel instrument named the Particle Into Nitroxide Quencher (PINQ). This instrument combines the BPEAnit ROS assay in conjunction with a purpose-built aerosol collection device, the insoluble aerosol collector (IAC). The IAC continuously collects PM regardless of size or chemistry directly into a liquid sample with a collection efficiency of 0.98 and a low cut-off size of < 20 nm. The sampling time resolution of the PINQ is one minute, with a limit of detection (LOD) of 0.08 nmol m−3 in equivalent BPEAnit-Me concentration per volume of air. This high sample time resolution and sensitivity is achieved due a combination of the highly concentrated IAC liquid sample and the rapid reaction and stability of the BPEAnit probe.

Introduction Diesel emissions have a high level of particulate matter which can cause inflammation and oxidative stress in the airways. A strategy to reduce diesel particulate matter and the associated adverse effects is the use of biodiesels and fuel additives. However, very little is known about the biological effects of these alternative emissions. The aim of this study is to compare the effect of biodiesel and triacetin/biodiesel emissions on primary human bronchial epithelial cells (pHBECs) compared to diesel emissions. Methods pHBECs were exposed to diesel, biodiesel (20%, 50% and 100% biodiesel derived from coconut oil) and triacetin/biodiesel (4% and 10% triacetin) emissions for 30 min at air-liquid interface. Cell viability (cellular metabolism, cell death, CASP3 mRNA expression and BCL2 mRNA expression), inflammation (IL-8 and IL-6 secretion), antioxidant production (HO-1 mRNA expression) and xenobiotic metabolism (CYP1a1 mRNA expression) were measured. Results Biodiesel emissions (B50) reduced cell viability, and increased oxidative stress. Triacetin/biodiesel emissions (B90) decreased cell viability and increased antioxidant production, inflammation and xenobiotic metabolism. Biodiesel emissions (B100) reduced cell viability, and increased IL-8 secretion and xenobiotic metabolism. Conclusions Biodiesel substitution in diesel fuel and triacetin substitution in biodiesel can increase the adverse effects of diesel emissions of pHBECs. Further studies of the effect of these diesel fuel alternatives on pHBECs are required.

Introduction: Diesel particulate matter can cause inflammation and oxidative stress in the airways. A strategy to reduce adverse effects associated with particulate matter in diesel emissions is the use of biodiesels and fuel additives such as triacetin, but very little is known about the health effects of these alternative emissions. The aim of this study is to evaluate the effects of biodiesel and triacetin/biodiesel emissions on primary human bronchial epithelial cells (pHBECs) in comparison to conventional diesel emissions. Methods: Primary HBECs were differentiated at air-liquid interface and exposed to diesel (D100), biodiesel (B20, B50 and B100: 20%, 50% and 100% biodiesel derived from waste cooking oil, respectively) and triacetin/biodiesel (B96 and B90: 4% and 10% triacetin in biodiesel, respectively) emissions for 30 minutes. Indicators of cell viability, inflammation, antioxidant production and xenobiotic metabolism were measured. Results: Biodiesel and triacetin substitution altered the particulate matter composition of the diesel emissions. B50, B90 and B100 significantly increased percentage cell death (75%, 60.9 and 49%, respectively). B50 and B90 significantly increased HO-1 mRNA expression (16.9-fold and 18.3-fold increase, respectively). B90 and B100 significantly increased IL-8 secretion (6.9-fold and 3-fold increase, respectively). Conclusions: Biodiesel fuels and fuel additives (triacetin) reduce particulate matter in diesel emissions, but have adverse effects on bronchial epithelial cell viability, metabolism and antioxidant production, compared to conventional diesel emissions. Further studies of the effect of diesel fuel alternatives on pHBECs are required.

Air pollution exposure is associated with a range of adverse health effects, including cardiovascular and respiratory diseases. Particle-bound ROS has been recognised as one of the prevailing parameters to indicate the toxic potential of airborne particulate matter (PM). The temporal variability of particle-bound ROS is a very important metric crucial for the improvement of public health and risk assessment policies. To our knowledge this is the first study aiming to investigate diurnal ROS profiles in both the particle and gas phase and associate them with diurnal variations of important pollutants. For that purpose, we have successfully applied a new instrument to continuously monitor diurnal ROS profiles at two locations in Hong Kong: a busy roadside and an urban background. Data was collected over both the working week and during weekends. We have observed a high correlation between particle-bound ROS and lower concentrations of black carbon (BC) at the roadside during the working week. These associations were less significant over the weekend and at all times with ozone. Our results suggest that most of the particle-bound ROS from both the particle and the gas phase arises from fresh emission sources directly from the traffic. A very interesting observation came out as a result of this study where measured ROS concentration was decreasing with the rise of ozone in conjunction with particle number, suggesting potential role of ROS in particle growth and aging.