Search

Frequency response analysis (FRA) is being employed worldwide as one of the main methods for the internal condition assessment of transformers due to its capability of detecting mechanical changes. Nonetheless, the objective interpretation of FRA measurements is still a challenge for the industry. This is mainly attributable to the lack of complete data from the same or similar units. A large database of FRA measurements can contribute to improving classification algorithms and lead to a more objective interpretation. Due to their destructive nature, mechanical deformations cannot be performed on real transformers to collect data from different scenarios. The use of simulation and laboratory transformer models is necessary. This research contribution is based on a new method using Finite Element Method simulation and a lumped element circuit to obtain FRA traces from a laboratory model at healthy and faulty states, along with an optimization method to improve capacitive parameters from estimated values. The results show that measured and simulated FRA traces are in good agreement. Furthermore, the faulty FRA traces were analyzed to obtain the characterization of faults based on the variation of the lumped element’s parameters. This supports the use of the proposed method in the generation of faulty frequency response traces and its further use in classifying and localizing faults in the transformer windings. The proposed approach is therefore tailored for generating a larger and unique database of FRA traces with industrial importance and academic significance.

In the last decades, a large focus is being placed on the sustainability and safety of the power transformer spectrum. Ester liquids, which have interesting properties such as high fire point and biodegradability, are gaining needed attraction. Since in-service condition, thermal aging deteriorates the physicochemical and electrical properties of liquid dielectrics, it is important to study their long-term behavior. In this contribution, the pre-breakdown and breakdown behavior of ester fluids (synthetic and natural) under AC stress are investigated. Important characteristics, such as partial discharge pre-inception voltage, partial discharge inception voltage, breakdown voltage, average streamer velocity, and inception electric field, were assessed. The influence of the radius of curvature (of high voltage needle electrode) as well as the thermal degradation of typical ester liquids are also discussed. Mineral oil was also included in the tests loop as a benchmark for comparative purposes. It is found that the pre-inception voltage of ester liquids was, in most cases, higher than that of mineral oil. For a given radius of curvature, the streamer inception and breakdown voltages decreased with thermal aging. During the streamer initiation, the electric field at the electrode tip decreased with the increase in the radius of curvature. The velocity of the streamers seems to increase with the decrease in the radius of curvature. The period of vulnerability, the so-called “delay time”, seems to be independent of the aging or the radius of curvature for a given condition of the liquid.

The degradation of the insulation system in liquid-filled power transformers is a serious concern for electric power utilities. The insulation system’s ageing is accelerated by moisture, acids, oxidation products, and other decay particles (soluble and colloidal). The presence of these ageing by-products is detrimental to the insulation system and may further lead to premature ageing and serious consequences. The ageing mechanisms of oil-paper insulation are complex, highly interrelated, and strongly temperature-dependent. The operating temperature of the transformer insulating system has a direct relationship with the loading profile. The major aspect that is witnessed with the fluctuating temperatures is moisture migration and subsequent bubble evolution. In other words, gas bubbles evolve from the release of water vapor from the cellulosic insulation wrapped around the transformer windings. The models presented in the existing standards, such as the IEC Std. 60076-7:2018 and the IEEE Std. C57.91:2011, are mainly based on the insulation temperature, which acts as a key parameter. Several studies have investigated the moisture dynamics and bubbling phenomenon as a function of the water content in the paper and the state of the insulation system. Some studies have reported different prototypes for the estimation of the bubble inception temperatures under selected conditions. However, there are various attributes of the insulation system that are to be considered, especially when expanding the models for the alternative liquids. This paper reviews various evaluation models reported in the literature that help understand the bubbling phenomenon in transformer insulation. The discussions also keep us in the loop on the estimation of bubbling behavior in alternative dielectric liquids and key attributable factors for use in transformers. In addition, useful tutorial elements focusing on the bubbling issue in transformers as well as some critical analyses are addressed for future research on this topic.

The paper presents a physics-based method to calculate in real time the distribution of temperature in the active part of liquid immersed power transformers (LIPT) in a transient thermal processes during grid operation. The method is based on the detailed dynamic thermal-hydraulic network model (THNM). Commonly, up to now, lumped models have been used, whereby the temperatures are calculated at a few points (top-oil and hot-spot), and the parameters are determined from basic or extended temperature-rise tests and/or field operation. Numerous simplifications are made in such models and the accuracy of calculation decreases when the transformer operates outside the range of tested values (cooling stage, loading). The dynamic THNM reaches the optimum of accuracy and simplicity, being feasible for on-line application. The paper presents fundamental equations of dynamic THNM, which are structurally different from static THNM equations. The paper offers the numerical solver for the case of a closed-loop thermosyphon. To apply the method for real transformer grid operation, there is a need to develop details as in static THNM, which has been used to calculate the distribution of the temperatures in LIPT thermal design. The paper proves the concept of dynamic THNM using the experimental results of a closed-loop thermosyphon small-scale model, previously published by authors from McGill University in 2017. The comparison of dynamic THNM with measurements on that model are presented in the paper.