Search

Methylene blue (MB) is a most commonly used synthetic dye in the textile industry. It is an extremely carcinogenic phenothiazine derivative and therefore needs to be removed from the water bodies. In the present study, a single-step hydrothermal novel synthesis of carbon quantum dots (CQDs) extracted from biomass of chicken feathers has been performed, and the synthesized CQDs were applied to remove MB present in the aqueous samples. A number of techniques such as ultraviolet-visible (UV-Vis) spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD) were used to characterize the samples for the conformity purposes. SEM and XRD analysis showed that CQDs are highly crystalline and have spherical structures with an average particle diameter of 35 nm. In the presence of 0.2 g of synthesized CQDs, MB dye degraded drastically under the sunlight. The rate of degradation was studied by determining the absorbance of the degraded sample with time relevant to untreated sample. The % degradation achieved during first 60 min of time was approximately 92% which increased minimally to a value of only 95% after 100 min of time. The ease of synthesis of carbon dots at low cost contributes hugely to their utilizations as an efficient photocatalyst for the degradation of aqueous pollutants. The opted approach to synthesize CQDs is cost-effective and eco-friendly and demonstrates excellent potential to remove MB from the aqueous samples.

In present work, facile synthesis of a biocompatible hybrid biosorbent based on diethylenetriaminepentaacetic acid (DTPA) modified chitosan immobilized in organo-functionalized sodium alginate matrix (DTPA-MCSA) was carried out. DTPA-MCSA was casted in microspherical hydrogel beads. Three dimensional microporous geometry of the biosorbent remained well preserved as observed in SEM analysis which revealed the improved mechanical strength of the alginate matrix. Surface functionalization of base biopolymers was confirmed by FTIR and SEM analysis. Equilibrium sorption studies using DTPA-MCSA for Cu(II) from aqueous medium were carried out in batch mode and found considerably dependent on pH, contact sorption time, temperature and initial copper concentration. Isothermal sorption data showed close correlation with Langmuir model as evident from nonlinear fitting of data (R 2 ˜ 0.99) at different temperatures. The experimental sorption capacity (q e) was found nearly 67 mg/g using 100 mg/L initial concentration of copper ions. Kinetic studies were conducted using different initial concentrations for better elucidation of results and it showed better correlation with pseudo second order rate equation which unveiled that strong ion pair coordination and complexation exist between Cu(II) and newly grafted chelating sites of DTPA-MCSA. Thermodynamic parameters suggested that the adsorption process is spontaneous and endothermic. The results concluded that DTPA-MCSA could be a better candidate for adsorptive remediation of copper ions from liquid waste.

The kinetics of polypropylene pyrolysis has been studied under isothermal and non-isothermal conditions using Arrhenius and Kissinger–Akahira–Sunose (KAS) equations. Under isothermal conditions, applying first order kinetic model, activation energy (Ea) and pre-exponential factor (A) were investigated and observed as 119.7 kJ mol−1 and 1.2 × 1010 min−1, while in case of non-isothermal kinetics using Kissinger–Akahira–Sunose method, the average Ea and A were found to be 91.23 kJ mol−1 and 2.3 × 107 min−1, respectively. A comparison among the isothermal and non-isothermal reactions was made on the basis of kinetics parameters. The results from both the methods showed trivial variation in kinetic parameters of the pyrolysis reaction which may be due to two major reasons. Firstly, the selection of the kinetic model applied and secondly the inconsistency due to various experimental conditions used which can be reduced at optimized conditions. As the disposal of plastic materials need reliable kinetics information to model their decomposition reactions, therefore, the kinetics data thus obtained from pyrolysis reaction of model polypropylene will help in the utilization of polypropylene waste as energy source on industrial scale.

In this study, chemical modification of chitosan has been carried out using epichlorohydrin as crosslinking agent and ethyl acetoacetate as a modifier to graft acetoacetyl moiety. The said organo-functionalization on chitosan and sodium alginate not only offered a novel support for TiO2 immobilization but also enhanced sorption performance for Ni(II) recovery from aqueous medium. So, a composite consisting of acetoacetyl moiety grafted chitosan, sodium alginate and titanium oxide (EAA-MCS/TiO2) was prepared and characterized by fourier transform-infra red (FT-IR) spectroscopy and scanning electron microscopy (SEM). The hybrid composite (3EAA-MCS/TiO2) which had TiO2 to EAA-MCS mass ratio of 20.0% by weight showed maximum sorption efficiency. The formulated sorbent was conditioned in the form of hydrogel beads for operation. Isothermal sorption and kinetics studies were performed at pH = 6.0 to configure the nature of sorption. Pseudo-2nd order rate expression better explained the sorption kinetics and chemisorption is the predominant mode of uptake. Langmuir adsorption model better explained the sorption process (R 2 ∼ 0.99) and maximum monolayer sorption capacity (q m ) at sorption/desorption dynamic equilibrium was computed as 403 mg/g at optimized pH.

Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG geförderten) Allianz- bzw. Nationallizenz frei zugänglich. This publication is with permission of the rights owner freely accessible due to an Alliance licence and a national licence (funded by the DFG, German Research Foundation) respectively. This article describes the catalytic cracking of low-density polyethylene over attapulgite clay and iron substituted tungstophosphate/attapulgite clay (Fe-POM/attapulgite) composite materials to evaluate their suitability and performance for recycling of plastic waste into liquid fuel. The prepared catalysts enhanced the yield of liquid fuel (hydrocarbons) produced in cracking process. A maximum yield of 82% liquid oil fraction with a negligible amount of coke was obtained for 50% Fe-POM/attapulgite composite. Whereas, only 68% liquid oil fractions with a large amount of solid black residue was produced in case of non-catalytic pyrolysis. Moreover, Fe-POM/attapulgite clay composites showed higher selectivity towards lower hydrocarbons (C5–C12) with aliphatic hydrocarbons as major fractions. These synthesised composite catalysts significantly lowered the pyrolysis temperature from 375°C to 310°C. Hence, recovery of valuable fuel oil from polyethylene using these synthesised catalysts suggested their applicability for energy production from plastic waste at industrial level as well as for effective environment pollution control.

In this study, organo-funtionalization of sodium-alginate has been carried out using phenylsemicarbazide as modifier to graft N, O-donor atoms containing functional groups (amino-carbamate moieties) to offer novel support for TiO2 immobilization. Hybrid composite made of aminocarbamated alginate, carboxymethyl chitosan (CMC) and titanium oxide TiO2 (MCA-TiO2) was prepared for the promising adsorptive remediation of Ni(II). FT-IR, SEM-EDX were employed to characterize MCA-TiO2. The optimization of TiO2 to modified alginate mass ratio was carried out and hydrogel beads with TiO2/MCA mass ratio of 10.0% (2MCA-TiO2) revealed highest sorption efficiency. The produced sorbents were adapted in the form of hydrogel beads for operation. Organic functionalization based on aminocarbamate ( O CO NHNH2) moieties on linear chains of alginate embedded additional chelating functional sites which enhanced sorption and selectivity. Batch mode experiments were conducted for optimization of pH and sorbent dose. Equilibrium sorption, kinetic and thermodynamic studies were performed to pattern the nature of sorption. Kinetic data was found in close agreement with pseudo-second order rate expression (PSORE). Isothermal equilibrium sorption data was well fitted with Langmuir adsorption model. Maximum sorption capacity was evaluated as 229 mg/g at 298 K and pH = 6.0.

Microbial fuel cells (MFCs), a technology that converts chemical energy into electrical energy, have been regarded as the most suitable method for sustainable energy production. However, most MFCs generate a low power output, limiting their large-scale industrial applications. Here, we introduce a high-performancesingle-chambered microbial fuel cell (SCMFC) based on carbon fiber anode and zinc oxide nanoparticle (ZnO NP)-fabricated copper cathode. Furthermore, best optimized conditions of temperature, pH, substrate, external resistance, and cathode fabrication were also considered to evaluate the performance of this SCMFC in treating potato wastewater along with bioenergy production. Results indicated that chemical oxygen demand (COD) could be effectively removed (80%) and maximum voltage, current density, and power density were 1.58 V, 0.235 mA/cm2, and 0.3714 mW/cm2, respectively. Hence, the SCMFC used in this study has a higher potential to treat potato wastewater along with high power production.

Methyl orange (MO) is a highly carcinogenic and harmful contaminant, which has been extensively reported for its detrimental impact on human and aquatic life. The photodegradation of MO into less toxic products has gained much attention over the past few decades. Herein we have reviewed the recent advancement in designing of nanomaterials (NMs) stabilized on different fabricating assemblies and their application in photocatalysis of MO dye. These photocatalytic systems possess various advantages and disadvantages. Graphene-based supported materials on different NMs are highly reported photocatalysts for photocatalysis of MO dye. Recent advancement, parameters affecting photocatalytic studies, kinetics and photocatalytic mechanism of MO have been thoroughly explained in this review. Future outcomes are also provided for extending the development of scientific research in this field.

The current study is based on the synthesis and characterization of ZnO–NiO/rGO nanohybrid for photocatalytic degradation of organic pollutants. The physicochemical properties of synthesized products were estimated by X-ray diffraction technique (XRD), Fourier transform infrared spectroscopy (FTIR), field emission-scanning electron microscopy (FESEM), and Ultraviolet–Visible spectroscopy. The diffraction data showed the formation of binary metal oxide nanocomposite, containing ZnO in hexagonal whereas NiO in the cubic crystalline phase. XRD results revealed that the calculated crystallite size of NiO and ZnO in the ZnO–NiO nanocomposite was

Coronavirus Disease-2019 (COVID-19), emerged in Wuhan (China) during December 2019, has now grown into a global scale pandemic that is influencing the civilization of the whole world. As of 25th March 2020, the World Health Organization (WHO) has released 65 situation reports starting from 23rd January 2020 to 26th March 2020 regarding this new disease. The virus has now been identified and named as Severe Acute Respiratory Syndrome Coronavirus-2 (SARS-- CoV-2). Total confirmed cases documented across the globe have reached up to 462,684 including 20,834 confirmed deaths from this disease as of 26th March 2020. This study focuses on the essential developments, or response procedures opted by the various countries and presents an elaborative account of the various steps taken by the Pakistan government to respond to this dynamic situation. As a third world country, the fall out of these actions can have severe repercussions. This study attempted to highlight some of the peculiar trials Pakistan is facing in these challenging times and discusses the effect of COVID-19 from the perspective of the third world nation. We believe that this study will provide a realistic picture of the current scenario taking place in Pakistan and will assist the government and concerned institutions/agencies in developing better plans for effectively dealing with this COVID-19 virus.

The aim of the study was to synthesize zinc oxide nanoparticles (ZnONPs) composite with clay by a novel route and then to explore the capability of composite of ZnONPs and silty clay (SC) as adsorbents for Pb (II) eradication from aqueous media by batch adsorption method. The effect of different operating factors like temperature, pH, dose and time of contact on the adsorption process were studied to optimize the conditions. Langmuir, Freundlich, Dubinin–Radushkevich (D-R) and Temkin isotherms were applied for the interpretation of the process. The R2 and q values obtained from Langmuir model suggested that the process is best interpreted by this model. The values of adsorption capacity (qm) noted were 12.43 mg·g−1 and 14.54 mg·g−1 on SC and ZnONPs-SC respectively. The kinetic studies exposed that pseudo second order (PSO) kinetics is followed by the processes suggesting that more than one steps are involved to control the rate of reactions. Various thermodynamic variables such as change in free energy (ΔGϴ), change in enthalpy (ΔHϴ) and change in entropy (ΔSϴ) were calculated. Thermodynamic data suggested that Pb (II) adsorption on SC and ZnONPs-SC are spontaneous, endothermic and feasible processes.

The increase in industrialization and development has tremendously diminished fossil fuel resources. Moreover, the excessive use of fossil fuels has resulted in the release of various toxic gases and an increase in global warming. Hence, necessitating the need to search for a renewable energy source. In this study, sesame waste biomass (SWB), which is abundantly available in Pakistan, has been used as feedstock for obtaining bio-oil using the pyrolysis technique. Pyrolysis was carried out using thermogravimetry and a pyrolysis chamber. Firstly, thermogravimetric analysis was performed on biomass with/without a laboratory synthesized catalyst Ni/Co/MCM-41 in nitrogen at different temperature programmed rates of 5, 10, 15, and 20 °C/min. A four-stage weight loss was observed that pointed toward the vaporization of water, and degradation of hemicelluloses, cellulose, and lignin. The kinetics parameters were determined using the Kissinger equation. The activation energy for the decomposition reaction of hemicelluloses, cellulose, and lignin, without catalyst, was observed as 133.02, 141.33, and 191.22 kJ/mol, respectively, however, with catalyst it was found as 91.45, 99.76, and 149.65 kJ/mol, respectively. In the catalyzed reaction the results showed the lowest activation energy, which is an indication of the fact that the catalyst is successful in reducing the activation energy to a sufficient level. As the TG/DTG showed active degradation between 200 and 400 °C, therefore, the waste sesame biomass over Ni-Co/MCM-41 was pyrolyzed within the same temperature range in the pyrolysis chamber. Temperature and time were optimized for maximum oil yield. A maximum oil yield of 38% was achieved at 330 °C and 20 min. The oil obtained was studied using GCMS. The physicochemical characteristics of the oil were assessed, and it was found that if the oil was upgraded properly, it could serve as a fuel for commercial use.

The detection of human serum albumin (HSA) is of significant clinical importance in disease diagnoses. In this work, polymer-based synthetic receptors are designed by incorporating Ag-ZnS microspheres in molecularly imprinted poly(methacrylic acid-co-ethylene glycol dimethacrylate) (MIPs) for the gravimetric detection of HSA. Among different compositions of Ag-ZnS@MIPs, MIPs having methacrylic acid and ethylene glycol dimethacrylate volume ratio of 3:2 exhibit enhanced HSA sensitivity in the concentration range of 5–200 ng/mL. A remarkably low threshold limit of detection (LOD = 0.364 ng/mL) is achieved with quartz crystal microbalance (QCM) based gravimetric sensors. Furthermore, the Ag-ZnS@MIPs/QCM sensors show high selectivity for HSA compared to other proteins, e.g., bovine serum albumin (BSA), glycoprotein, ribonuclease, and lysozyme. Hence, the gravimetric quantification of HSA realizes a highly sensitive, selective, and label-free detection mechanism with a limit of quantification down to 1.1 ng/mL.

Pyrolysis of Prunus dulcis was performed in the presence off our catalysts (ZnCl2, Fe2O3, Alumina, and ZSM-5) using a fixed bed tubular reactor. The factors affecting the product yield were premedi...

In this study, the essential oil composition and antibacterial activity of the resin of Canarium strictum Roxb. was investigated. The oil was extracted by microwave-assisted extraction and analyzed...

In this study, we reviewed the biogenic route for the synthesis of iron nanomaterials (Fe-NMs) with special emphasis on recent progress. Natural products or its derivatives including extract of pla...

This study covers chemical profiling of leaf essential oil of Plectranthus scutellarioides (L.) R.Br along with the first report on its antibacterial activity. The extraction was performed by micro...

In present work, Semolina being used as biomass served to be the polymer matrix within which ZnO nanoparticles were incorporated. ZnO nanoparticles were biogenically synthesized using Syzygium cumi...

Copper and copper oxide nanoparticles (Co/CoO NPs) were synthesized by a green approach using Syzygium cumini leaf extract. The formation of synthesized Co/CoO NPs was monitored by using UV–Visible...

A microbial fuel cell is an efficient, cost-effective, and green methodology for electricity production and wastewater treatment. A single chambered microbial fuel cell (SCMFC) was designed to gene...

A novel pyrazole grafted MCM-41 hybrid has been synthesized by post-grafting method for targeted water purification. MCM-41 was first functionalized with 3-aminopropyltriethoxysilane (APTES) followed by immobilization of acyl functionalized pyrazole derivative through Schiff’s base formation. Fourier transform infrared (FTIR) spectroscopy, solid state 13C nuclear magnetic resonance (NMR) spectroscopy, thermogravimetric analysis (TGA) and elemental analysis confirmed the covalent attachment of organic moiety to the silica surface, whilst scanning electron microscope (SEM) and N2 adsorption–desorption analysis confirmed the structural integrity and the preservation of mesoporous structure of MCM-41 during surface modification. The novel material showed excellent results for the removal of Pb(II) metal ions with highest adsorption capacity (qe) of 2416 mg g−1. With this adsorption capacity, the prepared hybrid efficiently removed 96.6% of Pb(II) metal ions from aqueous solution using minimum adsorbent concentration (1 mg) ever reported. The adsorbent was reused for five cycles with minimum 94.85% removal efficiency after simple treatment with 6 N HCl. This reusable adsorbent may further be applied for heavy metal removal from industrial effluent.

A novel hybrid biocomposite based on amino-thiocarbamate derivative of alginate, carboxymethyl chitosan and TiO2 (TiO2/TSC-CMC) was fabricated and characterized using Fourier transform Infrared spectroscopy (FTIR), Scanning electron microscopy (SEM) and Energy dispersive X-ray spectroscopy (EDX). The TiO2/TSC-CMC mass ratio (5.0–30.0%) was optimized and 3TiO2/TSC-CMC (hydrogel beads with TiO2/TSC-CMC mass ratio of 20.0%) was selected as the best sorbent for effective biosorption of Ni(II). Batch sorption experiments were conducted, instantaneous and equilibrium sorption capacities were investigated as function of pH, sorbent dose, initial metal concentration, contact time and temperature. Kinetic data could be well explained through pseudo second order rate equation (PSORE) depicting that the rate determining step involves the transfer of electron density from sorbent functional sites to central metal ion. Langmuir model fitted well with isothermal sorption data and maximum monolayer sorption capacity (qm) was computed as 172 mg/g at pH 6.0 and temperature 298 K. The values of thermodynamic parameters such as standard enthalpy change (16.94 kJ/mol) and standard Gibbs energy change (−18.67, −19.48, −20.57, and −21.38 kJ/mol) and standard entropy change (0.12 kJ/mol·K) concluded that sorption process is endothermic, spontaneous and resulted with increase in randomness. Hence, 3TiO2/TSC-CMC was found efficient and reusable sorbent.

In the present work, the slow pyrolysis has been executed in a tubular shaped fixed bed reactor using corn cob as biomass and superparamagnetic iron oxide nanoparticles (Fe3O4-NPs) as a catalyst. F...

The potentials of silty clay (SC), acquired from Chaman, Balochistan, were investigated as adsorbent for Ni (II) and Cd (II) removal from contaminated media. The influence of different operating factors like dose, pH, temperature, and time of contact was explored, and optimum values were noted under batch adsorption method. Isothermal study was conducted with varying concentrations of solutions on optimized conditions and different adsorption models i.e., Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D–R) isotherm, which were employed to interpret the process. The isothermal data of both Ni (II) and Cd (II) were well fitted to Langmuir isotherm suggesting the formation of monolayer of metal ions on silty clay. The values of adsorption capacity noted for Ni (II) and Cd (II) were 3.603 mg·g−1 and 5.480 mg·g−1, respectively. Kinetic studies affirmed that pseudo second order (PSO) kinetics was being obeyed by the removal of Ni (II) and Cd (II). Thermodynamic variables like free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were calculated. The negative value of ΔG° and the positive values of ΔH° and ΔS° unfolded that the removal process of both metal ions of by SC was spontaneous, endothermic and feasible.

In the present study, a novel biosorbent clay composite, based on carboxymethyl-chitosan/sodium alginate grafted with amino-carbamate moiety/bentonite clay (CA-CMC/Bt) was prepared. The produced sorbent was conditioned in the form of hydrogel beads by ionotropic gelation with Ca(II) ions, and thoroughly characterized using FTIR, XRF, XRD, SEM and zeta potential measurements. FTIR and SEM confirmed the successful grafting and intercalation of clay mineral into modified biopolymer. Hydrogel beads were observed to be very integrated and stable under a wide pH working range (from 2.0 to 12.0). CA-CMC/Bt was employed for adsorptive remediation of Ni(II) from aqueous media. Sorption process was found as a function of various parameters such as sorbent dosage, contact time, pH and initial concentration. Kinetic data could be well explained by pseudo second order rate equation (PSORE), suggesting that complexation or valence forces are playing significant role in the uptake of Ni(II) ions. Isothermal sorption data was analysed using different sorption models such as Langmuir, Freundlich and Sips. Data was well fitted with Langmuir and Sips model, maximum monolayer sorption capacity (qm) was calculated (by non-linear fitting of data) as 159 mg/g at 298 K and pH 5.5. Separation factor (RL) was found as 0 < RL < 1 which indicated favourable sorption. Thermodynamic parameters i.e. ΔGo, ΔHo and ΔSo were quantified and patterned the sorption process as exothermic, spontaneous with increase in system entropy. CA-CMC/Bt was found cost-effective, efficient and reusable material in Ni(II) competitive recovery.

Potential hazardous effects caused by non-biodegradable plastics are considered to be one of the most widely discussed and notable challenges of the 21st century. To address this particular problem, immense efforts have been devoted to the preparation of biodegradable plastics material. This green approach mitigates the major drawbacks e.g. improper waste management, low degradation rates, waste accumulation in water reservoirs and harmful chemical reagents hence providing a natural, economical and biodegradable alternative to the customarily employed non-biodegradable plastics. This review provides an insight into recently engineered biodegradable plastics used for packaging applications. Properties such as barrier/permeation indexes, thermal, electrical and mechanical characteristics of the biodegradable plastics are considered in detail for developing an understanding regarding the fundamentals of biodegradable materials. Recent literature (2010-2018) was classified according to the composition and nature of the used material. Materials such as polylactic acid, polyhydroxyalkanoates, polyhydroxybutyrate, polycaprolactone, starch and cellulose were comprehensively discussed along with their properties and blending agents.

A novel green approach was adopted for carrying out the large scale synthesis of the Zinc oxide nanoflowers (ZNFs). The reducing power of maltose was utilized for reducing the precursor metal salt ...

Today various wastewater treatment methodologies such as chemical oxidation, biological treatment, chemical precipitation, fenton technology, and advanced oxidation processes are used to resolve wa...

A novel and facile green approach was adopted for carrying out the large scale synthesis of the nickel (Ni) and nickel oxide (NiO) nanoparticles (NPs). The seeds extract of Hordeum vulgare plant wh...

Conversion of nitroaniline (NA), a highly toxic pollutant that has been released into aquatic systems due to unmanaged industrial development in recent years, into the less harmful or a useful counterpart is the need of the hour. Various methods for its conversion and removal have been explored. Owing to its nominal features of advanced effectiveness, the chemical reduction of 4-NA using various different nanocatalytic systems is one such approach that has attracted tremendous interest over the past few years. The academic literature has been confined to case studies involving silver (Ag) and gold (Au) nanoparticles, as these are the two most widely used materials for the synthesis of nanocatalytic assemblies. Focus has also been given to sodium borohydride (NaBH4), which is used as a reductant during the chemical reduction of NA. This systematic review summarizes the fundamentals associated with the catalytic degradation of 4-NA, and presents a comprehensive and critical study of the latest modifications used in the synthesis of these catalytic systems. In addition, the kinetics, mechanisms, thermodynamics, as well as the future directions required for understanding this model reaction, have been provided in this particular study.