Search

Severe damage or collapse of reinforced concrete dapped-end beams (RC-DEBs) may occur during the service life. The collapse of the Concorde overpass structure in Laval, Quebec, Canada, in 2006 revealed the causes of collapse, i.e., insufficient shear strength (no stirrups), misplacement of hanger reinforcement, etc. In addition, the inspection report of RC half-joint bridges in England until 2018 expressed that damages or failures of half-joint structures can be attributed to the poor condition of structures or non-compliant reinforcement detailing. These conditions exhibited how important it is to understand the proper detailing of dapped-end reinforcement. To date, some studies have performed investigations on the effect of inadequate dapped-end reinforcement on the structural behavior of DEBs. However, the results of the research to date were not yet complete enough to disclose the role of each group of dapped-end reinforcement in resisting the working load. Therefore, this study was carried out to investigate the main role of each group of dapped-end reinforcement separately on the structural performance of RC-DEBs. Eight large-scaled RC-DEBs (with sizes of 1800 mm length, 120 mm width and 250 mm height) were prepared, cast and cured. All DEB specimens were tested under the three-point loading up to failure. To localize the effect of shear failure, the shear span-depth ratio (av⁄d) of 1.43 was set. Test results exhibited that arrangement of a specific group of dapped-end reinforcement separately affects the structural performance of DEBs significantly. The diagonal reinforcement (DR) group was found to be more effective than the vertical hanger reinforcement (HR) group. The failure load capacity of the DR group (DEB-18) achieved 0.29 times that of the control beam (DEB-3). Meantime, the nib flexure reinforcement (NFR) group demonstrated the most important role in the structural performance of DEBs compared to other dapped-end reinforcement groups. The failure load capacity of the NFR group (DEB-39) reached 0.62 times that of the control beam, while rupture deflection of the NFR group also exhibited the highest value than other groups, i.e., 0.62 times that of the control beam. In addition, analysis results of rosette strain gages (RSGs) data indicated that regions near to re-entrant corner and its vicinity experienced the highest stress concentration factor (SCF) compared to other places of the beams. These regions were more susceptible to experiencing the first crack, progressive crack, damage or failure first than other regions of DEBs. The greater the value of SCF, the greater the probability of collapse occurring in the related structural elements, which is also followed by a lower failure load capacity. DEB-1 (without dapped-end reinforcement) has the highest SCF (205.68), and the lowest failure load capacity (12.58 kN), whilst DEB-3 (with the complete dapped-end reinforcement) has the lowest SCF (79.62), but the highest failure load capacity (105.26 kN). Obviously, DEB-3 can withstand the working load properly. Its adequate dapped-end reinforcement is able to accommodate and distribute the high stress flows in the dapped-end region properly, which causes the SCF value to decrease.

Noise is continuously treated as an annoyance to humans and indeed commotion contamination shows up within the environment, causing inconvenience. This is likewise interesting to the engineering tactic that inclines to develop this noise proliferation. The basics of the sound-retaining proliferation, sound-absorbing properties, and its variables were rarely considered by previous researchers. Thus, the acoustic performance and sound insulation of constructions have gained significance over the last five decades due to the trend for accommodating inner-city flat and multi-story residential building condominiums. Due to this dilemma, the proliferation of high-driven entertaining schemes has engaged extraordinary demands on building for its acoustic performance. Yet, construction industries worldwide have started to mainly use sound-absorbing concrete to reduce the frequency of sounds in opened-and-closed areas and increase sound insulation. As reported, the concrete acoustic properties generally rely on its density, exhibiting that the lighter ones, such as cellular concrete, will absorb more sound than high-density concretes. However, this paper has an objective to afford a wide-ranging review of sound-absorbing acoustic concretes, including the measurement techniques and insulation characteristics of building materials and the sound absorption properties of construction materials. It is also intended to extensively review to provide insights into the possible use of a typical sound-absorbing acoustic concrete in today’s building industry to enhance housing occupants’ efficiency, comfort, well-being, and safety.

This study carried out a comprehensive review to determine the carbonation process that causes the most deterioration and destruction of concrete. The carbonation mechanism involved using carbon dioxide (CO2) to penetrate the concrete pore system into the atmosphere and reduce the alkalinity by decreasing the pH level around the reinforcement and initiation of the corrosion process. The use of bacteria in the concrete was to increase the pH of the concrete by producing urease enzyme. This technique may help to maintain concrete alkalinity in high levels, even when the carbonation process occurs, because the CO2 accelerates to the concrete and then converts directly to calcium carbonate, CaCO3. Consequently, the self-healing of the cracks and the pores occurred as a result of the carbonation process and bacteria enzyme reaction. As a result of these reactions, the concrete steel is protected, and the concrete properties and durability may improve. However, there are several factors that control carbonation which have been grouped into internal and external factors. Many studies on carbonation have been carried out to explore the effect of bacteria to improve durability and concrete strength. However, an in-depth literature review revealed that the use of bacteria as a self-healing mechanism can still be improved upon. This review aimed to highlight and discuss the possibility of applying bacteria in concrete to improve reinforcement concrete.

Engineered cementitious composite (ECC) was discovered as a new substitute of conventional concrete as it provides better results in terms of tensile strain, reaching beyond 3%. From then, more studies were done to partially replace crumb rubber with sand to achieve a more sustainable and eco-friendlier composite from the original ECC. However, the elastic modulus of ECC was noticeably degraded. This could bring potential unseen dangerous consequences as the fatigue might happen at any time without any sign. The replacement of crumb rubber was then found to not only bring a more sustainable and eco-friendlier result but also increase the ductility and the durability of the composite, with lighter specific gravity compared to conventional concrete. This study investigated the effects of crumb rubber (CR) and graphene oxide (GO) toward the deformable properties of rubberized ECC, including the compressive strength, elastic modulus, Poisson&rsquo, s ratio, and drying shrinkage. Central composite design (CCD) was utilized to provide 13 reasonable trial mixtures with the ranging level of CR replacement from 0&ndash, 30% and that of GO from 0.01&ndash, 0.08%. The results show that GO increased the strength of the developed GO-RECC. It was also found that the addition of CR and GO to ECC brought a notable improvement in mechanical and deformable properties. The predicted model that was developed using response surface methodology (RSM) shows that the variables (compression strength, elastic modulus, Poisson&rsquo, s ratio, and drying shrinkage) rely on the independent (CR and GO) variables and are highly correlated.

The push for sustainability in the construction sector has demanded the use of increasingly renewable resources. These natural fibers are biodegradable and non-toxic, and their mechanical capabilities are superior to those of synthetic fibers in terms of strength and durability. A lot of research recommends coconut fibers as an alternative to synthetic fibers. However, the knowledge is scattered, and no one can easily judge the suitability of coconut fibers in concrete. This paper presents a summary of research progress on coconut fiber (natural fibers) reinforced concrete. The effects of coconut fibers on the properties of concrete are reviewed. Factors affecting the fresh, hardened, and durability properties of concrete reinforced with coconut fiber are discussed. Results indicate that coconut fiber improved the mechanical performance of concrete due to crack prevention, similar to the synthetic fibers but decreased the flowability of concrete. However, coconut fibers improved flexure strength more effectively than compressive strength. Furthermore, improvement in some durability performance was also observed, but less information is available in this regard. Moreover, the optimum dose is an important parameter for high-strength concrete. The majority of researchers indicate that 3.0% coconut fiber is the optimum dose. The overall study demonstrates that coconut fibers have the creditability to be used in concrete instead of synthetic fibers.

Fine aggregate and cement have been partially replaced by 10% and 56% crumb rubber and class F-fly ash, respectively, in order to manufacture rubberized concrete interlocking bricks (RCIBs). The newly developed product has been used for masonry construction without the need for mortar (mortarless), and the experimental testing under compression load was investigated by Al-Fakih et al. Therefore, in line with that, this study carried out finite element (FE) analysis for experimental result validation of masonry walls and prisms made of RCIBs. ANSYS software was utilized to implement the FE analysis, and a plasticity detailed micro-modeling approach was adopted. Parametric studies were carried out on masonry prisms to investigate the effect of the slenderness ratio and the elastic modulus of grout on the prism behavior. The results found that the adopted FE model has the ability to predict the structural response, such as compressive strength, stiffness, and failure mechanism, of the interlocking masonry prisms with about a 90% agreement with the experimental results. Based on the parametric studies, the compressive strength for a 6-course prism is approximately 68% less than a 3-course prism and 60% less than a 5-course prism, which means that the slenderness ratio plays a vital role in the behavior of the RCIB masonry prism under the vertical compression load. Moreover, the results showed that the difference between FE and experimental results of the walls was less than 16%, indicating a good match. The findings also reported that masonry walls and prisms experienced higher ductility measured by the post-failure loading under compression. The finite element model can be used for further investigation of masonry systems built with rubberized concrete interlocking bricks.

This paper proposes a new type of lightweight concrete called bubble concrete, which was developed by mixing concrete with high-strength hollow bodies. In the present study, concave and spherical steel hollow bodies were used not only to form multiple cavities in the concrete but also to transfer internal stresses. Through compression tests, the shape effects and distribution effects of the hollow bodies on the strength and Young’s modulus of concrete were investigated. In addition, the mechanical characteristics of the bubble concrete were simulated by nonlinear elastoplastic finite element analysis to study the stress distribution and failure mechanism. The results indicate that with the proper combination, bubble concrete can reduce its density to 1.971–2.003 g/cm3 (83.3–84.7%, compared to control concrete) and its strength reaches 27.536–28.954 N/mm2.

Most Malaysian rural houses are categorized as non-engineered buildings and vulnerable to damage during events such as windstorms due to the fact that these houses lack engineering considerations. These houses are characterized by having an attached kitchen house, and many of these houses were previously damaged by thunderstorms. The current research investigated the air flow characteristics changes surrounding these houses as a result of the presence of the kitchen. The roof pitch, position, gap height, and overhang were investigated using computational fluid dynamics (CFD) simulations. The results showed that the kitchen position at the center resulted in a slight increase in the suction on the ridge of the roof; however, it significantly altered the flow pattern in the windward and leeward directions. The results also showed that the roof overhang, roof pitch, and kitchen position contributed severely to the damage of the rural house. Moreover, the highest suction occurred at the roof ridge when the kitchen was located at the center of the rural house (Cp = −2.28). Therefore, the authors believe that it is more advantageous to have a kitchen connected to the core as it reduces the pressure on the roof of the core during thunderstorm events.

This paper reports the findings of the effect of elevated temperature on the compressive strength and durability properties of crumb rubber engineered cementitious composite (CR-ECC). The CR-ECC has been tested for its compressive strength and chemical resistance test against acid and sulphate attack. Different proportions of crumb rubber (CR) in partial replacement to the fine aggregate and polyvinyl alcohol (PVA) fiber have been utilized from 0 to 5% and 0 to 2%. The experiments were designed based on a central composite design (CCD) technique of response surface methodology (RSM). After 28 days curing, the samples were preconditioned and exposed to high temperatures of 100 &deg, C, 200 &deg, C, 300 &deg, C, 400 &deg, C, 500 &deg, C, 600 &deg, C, 700 &deg, C, 800 &deg, C, 900 &deg, C, and 1000 &deg, C for one hour. Although the residual compressive strength of CR-ECC was negatively affected by elevated temperature, no explosive spalling was noticed for all mixes, even at 1000 &deg, C. Results indicated that CR-ECC experiences slight weight gain and a reduction in strength when exposed to the acidic environment. Due to the reduced permeability, CR-ECC experienced less effect when in sulphate environment. The response models were generated and validated by analysis of variance (ANOVA). The difference between adjusted R-squared and predicted R-squared values for each model was less than 0.2, and they possess at least a 95% level of confidence.

An experimental study is conducted to determine the influence of secondary reinforcement on the behaviour of corbels fabricated with three different types of high-performance fiber-reinforced cementitious composites, including engineered cementitious concrete (ECC), high-performance steel fiber-reinforced composite (HPSFRC), and hybrid fiber-reinforced composite (HyFRC). Two shear span-to-depth ratios (a/d = 0.75 and 1.0) are explored. The mechanical properties of the composites in terms of tensile, compressive, and flexural strengths are investigated. Next, the structural behaviour of the high-performance cementitious composite corbels in terms of ultimate load capacity, ductility, and failure modes under the three-point bending test are investigated. The secondary reinforcement is proven to significantly affect stiffness and ultimately load capacity of all three high-performance composite corbels with an aspect ratio of 0.75. However, the secondary reinforcement was more impactful for the HPSFRC corbels, with 51% increase of ultimate strength. Moreover, in terms of damage, fewer cracks occurred in ECC corbels. HPSFRC corbels displayed the highest level of ductility and deformation capacity compared to the other specimens. The results were comparatively analyzed against the predicted results using truss and plastic truss models which provided relatively reliable shear strength.