Search

In this paper, Kevlar or Polysulfonamide (PSA) pulp were used to replace plant fiber pulp partially or completely and by adjusting their ratios and a variety of Kevlar or PSA pulp reinforced activated carbon fiber paper (ACFP) were prepared via wet-laid paper making technology. The influences of addition of Kevlar or PSA pulp on the permeability, mechanical property, filtration performance, adsorption property of ACFP were discussed by maintaining the addition content of activated carbon fiber unchanged. Results showed that with the addition content of Kevlar or PSA pulp increased, the permeability and filtration performance of ACFP decreased obviously, while the bursting strength and the static CCl4 adsorption performances were firstly increased and then decreased. Generally, the permeability and filtration performance of Kevlar pulp reinforced ACFP were slightly worse than that of PSA pulp reinforced ACFP, while the bursting strength as well as the static CCl4 adsorption properties of Kevlar pulp reinforced ACFP were better than that of PSA pulp reinforced ACFP.

Fe-pillared bentonite was made into a paper-like composite by a papermaking technique using pulp fiber and activated carbon fiber. Orange II was used as a model compound to investigate the photocatalytic performance of the paper. SEM analysis showed that the catalytic paper had a porous structure originating from the layered fiber network, with Fe-pillared bentonite mostly embedded in the grooves along the axial direction of the carbon fibers. The optimum preparation conditions were: activated carbon fiber:Fe-pillared bentonite=1:2, activated carbon fiber:pulp fiber=5:3, the charges of Na2SiO3 and PAE were 2.5% based on the Fe-pillared bentonite and 0.4% based on the oven-dry fibers, respectively. The degradation ratio reached 85.2% at 180 min and after that little increase was observed. The catalyst could be repeatedly use and keep a high stability during the first 4 cycling use.

Super absorbent polymer (SAP) and fluff pulp were used as absorbing materials, and the different SAP mass ratio and fluff pulp were applied to paper diaper absorption core layer. Then, the influence of different SAP/fluff pulp in composite core layer on the paper diapers normal saline absorption rate and topsheet run-off were studied. Results showed that SAP has a significant effect on normal saline absorbency respect to fluff pulp. When the normal saline volume increased, the paper diapers absorption rate about normal saline decreased, while the topsheet run-off increased. When the SAP mass ratio to fluff pulp was 0.5:0.5, the liquid absorbency rate was 35.23 g/g, the paper diaper average absorption rate was 3.96 mL/s, and the biggest topsheet run-off was 13.25 g.

The aim of this research was to produce three-layer Medium Density Particleboard (MDP), with the addition of impregnated paper, in the inner layer, in proportions of 1; 5 and 20%. In this study, MDP was composed with particles of small size in outer layers, and larger particles in internal layer. After panel manufacturing, physical and mechanical tests based on Brazilian Code ABNT NBR 14.810 were carried out to determine moisture content; density; thickness swelling; water absorption; modulus of rupture (MOR) and modulus of elasticity (MOE) in static bending and internal adhesion. Test results were compared to commercial panels, produced with 100% Eucalyptus, considering the requirements specified by Brazilian Code. Properties presented values close to normative specifications, indicating positively the possibility of production of MDP using addition of waste paper impregnated.

Rabbit is a traditional textile material and has protein content about 93%. Rabbit hair wastes are abundantly present in textile processing due to its poor spinnability. In order to recycle the waste rabbit fiber effectively, the rabbit protein was researched. The papermaking method was performed for the first time and their properties of the hybrid paper were discussed in this study. Different contents of rabbit protein were successfully prepared and mixed with pulp fibers to remade papers. Finally, performances of these papers were characterized. The results showed that the surface of the rabbit protein paper was flat, white and writing fluently. The ink absorbance of novel paper increased. Moreover mechanical properties of the rabbit protein paper were stronger than the untreated paper. The folding endurance decreased firstly and then increased.

Both water repellency and water vapour barrier properties were endowed at paper surface by coating with beeswax-chitosan latex. It was found that the water vapour transmission rate of coated paper decreased as the drying temperature increased. However, water contact angle was not affected with it. Although the surface morphology deformed at high drying temperature, the roughness values maintained at micro-scale. Further analysis indicated that the water vapour barrier property of coated paper was influenced by the density of the coating layer.

Pulp from the oil palm empty fruit bunches (EFB) was extracted via Alkaline Peroxide Pulping (APP). The pulping process was conducted through three main steps; dewaxing of EFB, impregnation of alkaline peroxide (AP) into EFB and refining of biomass to finally produce the pulp. The varying peroxide levels and number of impregnation stages were found to affect the refining energy consumption and the properties of the resultant pulp and paper. Diagnosis by electron microscopic imaging revealed a strong correlation between paper properties development and paper surface morphologies. By multiplying the stages of the low alkaline peroxide level (2:2.5% AP) impregnation, refining energy could be reduced by 30% while improving brightness and paper mechanical properties. Higher alkaline peroxide level (4:5% AP) could reduce the refining energy by 50% while still improving brightness. Beyond these AP levels (8:10% AP), refining energy could be reduced by 67% by increasing the number of impregnation stages, with positive effects on brightness and paper mechanical properties. The findings suggest that increasing the AP impregnation stages had exposed more active sites to react with AP. The enhanced AP accessibility to EFB structures facilitated mechanical fibrillation of EFB vascular bundles through the refining process. The proper synergy between AP and the adopted mechanical refining was the factor that triggered the liberation of nanocells from EFB biomass and this had ultimately improved paper properties.

Ink penetration and distribution affect the final appearance of printing and usage of ink, which are closely concerned by printer and paper maker. The objective of this experiment was to investigate the relationship between drying and back trap mottle. The different drying temperature was carried out to change the coating structure and properties. Fluorescent ink was used to observe and characterize ink distribution by LSCM. The results indicated that drying temperature affected ink distribution evenness. Higher and lower drying temperature could not contribute to ink absorption uniformity. Appropriate drying temperature could contribute to form the best printability of coated paper. Backtrap mottle was tightly linked with ink penetration evenness and uniform ink absorption leaded to little back trap mottle.

The structure of the coating layer has a strong influence on the optical and physical properties of paper as well as on the print quality. Ink is transferred and sets onto the paper surface in the printing process, which affect printing quality and usage of ink. The objective of this experiment was to investigate the influence of calender on coating surface structure and Printability. The surface structure was explored in the method of numerical and visual analysis using mercury porosimetry measurement and scanning electron microscopy (SEM). The findings indicated that the calender treatment affected the pore size, depth and distribution of the coated paper surface. It could be concluded that Calender could increase the smoothness, gloss and paper surface efficiency of coated paper, which resulted in lower amount of ink usage, lower amount of ink absorption and higher print density.

The electric papers have a wide variety of uses like in transformers, cables and power capacitors. Each application involves different requirements related to its mechanical and electric properties. The kraft is the dielectric paper most used due its high mechanical resistance and a dielectric strength of around 5 kV/mm that is increased up to 30 kV/mm when is impregnated with mineral oil and typically has a density of 0.7, nevertheless continuous improvements in the design, for example, of power transformers raise the need to improve its electrical properties particularly those related to its relative permittivity. In this article, structural parameters such as distribution and pore size of kraft paper and theoretical analysis for possible addition of nanofillers to improve their dielectric behavior are reported. A possible and better criterion for designing transformers can be the employment of kraft paper nano-inserted with 5 % of TiO2 or BaTiO3 stew in mineral oil and immersed in natural ester liquid.