Search

The development of scalable membrane-based separation processes has attracted considerable interest on laboratory and industrial scales. Polyvinylidene fluoride (PVDF) is one of the most widely used fluoropolymer materials for membrane fabrication due to its excellent mechanical strength, good thermal stability and chemical resistance as well as aging resistance. However, the hydrophobic nature of PVDF has resulted in serious membrane fouling during the filtration process. From the past decade, the embedment of hydrophilic materials in/on PVDF-based membranes can significantly alter the membrane’s morphology and surface properties. Therefore, based on most articles retrieved from Web of Science, Scopus, Google Scholar, etc., this article provides the overview of the recent development of PVDF-based membranes during the recent several decades. The detailed information regarding PVDF as a polymer material as well as the main challenge in the development of PVDF-based membranes with better performance was summarised. Moreover, the factors influencing membrane fouling including surface hydrophilicity, roughness and charge are also addressed. Then, the PVDF-based membrane preparation and its recent modification via the blending method were discussed. Finally, the overview and future perspective of PVDF-based membrane development are reviewed. Overall, it can be concluded that PVDF-based membranes have great potential for further advances towards the development of membrane technologies for the future.

The development of scalable membrane-based separation processes has attracted considerable interest on laboratory and industrial scales. Polyvinylidene fluoride (PVDF) is one of the most widely used fluoropolymer materials for membrane fabrication due to its excellent mechanical strength, good thermal stability and chemical resistance as well as aging resistance. However, the hydrophobic nature of PVDF has resulted in serious membrane fouling during the filtration process. From the past decade, the embedment of hydrophilic materials in/on PVDF-based membranes can significantly alter the membrane’s morphology and surface properties. Therefore, based on most articles retrieved from Web of Science, Scopus, Google Scholar, etc., this article provides the overview of the recent development of PVDF-based membranes during the recent several decades. The detailed information regarding PVDF as a polymer material as well as the main challenge in the development of PVDF-based membranes with better performance was summarised. Moreover, the factors influencing membrane fouling including surface hydrophilicity, roughness and charge are also addressed. Then, the PVDF-based membrane preparation and its recent modification via the blending method were discussed. Finally, the overview and future perspective of PVDF-based membrane development are reviewed. Overall, it can be concluded that PVDF-based membranes have great potential for further advances towards the development of membrane technologies for the future.

Exposure of synthetic dye, such as methylene blue (MB), in water bodies led to a serious threat to living things because they are toxic and non-degradable. Amongst the introduced dye removal methods, membrane separation process can be considered a powerful technique for treating dye contamination. However, this method commonly sufered from drawbacks, such as short membrane lifetime, low permeability and selectivity. To overcome these issues, graphene oxide (GO) and titanium dioxide (TiO2) were used as additives to fabricate polyethersulfone (PES)- and polyvinylidene fuoride (PVDF)-based hybrid membranes via non-solvent-induced phase separation method. Prior to membrane fabrication, GO was synthesised via electrochemical exfoliation method assisted by customised triple-tail surfactant. The potential of PES- and PVDF-based hybrid membranes for wastewater treatment has been discussed widely. However, direct comparison between these two polymeric membranes is not critically discussed for MB dye separation application yet. Therefore, this study is aimed at evaluating the performance of diferent types of polymers (e.g. PES and PVDF) in terms of membrane morphology, properties, dye rejection and antifouling ability. Results showed that the incorporation of GO and TiO2 alters the morphology of the fabricated membranes and afects dye rejection further, as well as their antifouling performance. In contrast with pristine membrane, PES-GO/TiO2 and PVDF-GO/TiO2 possessed high hydrophilicity, as indicated by their low contact angle (67.38° and 62.12°, respectively). Based on this study, PVDF-GO/TiO2 showed higher porosity value (94.88%), permeability (87.32 L/ m2 hMPa) and MB rejection rate (92.63%), as well as fux recovery ratio value of>100% as compared with others. Overall, the incorporation of GO and TiO2 with PVDF polymer are proven to be efective hybrid materials of membrane fabrication for dye rejection application in the near future. The polymer material’s intrinsic prope

Exposure of synthetic dye, such as methylene blue (MB), in water bodies led to a serious threat to living things because they are toxic and non-degradable. Amongst the introduced dye removal methods, membrane separation process can be considered a powerful technique for treating dye contamination. However, this method commonly sufered from drawbacks, such as short membrane lifetime, low permeability and selectivity. To overcome these issues, graphene oxide (GO) and titanium dioxide (TiO2) were used as additives to fabricate polyethersulfone (PES)- and polyvinylidene fuoride (PVDF)-based hybrid membranes via non-solvent-induced phase separation method. Prior to membrane fabrication, GO was synthesised via electrochemical exfoliation method assisted by customised triple-tail surfactant. The potential of PES- and PVDF-based hybrid membranes for wastewater treatment has been discussed widely. However, direct comparison between these two polymeric membranes is not critically discussed for MB dye separation application yet. Therefore, this study is aimed at evaluating the performance of diferent types of polymers (e.g. PES and PVDF) in terms of membrane morphology, properties, dye rejection and antifouling ability. Results showed that the incorporation of GO and TiO2 alters the morphology of the fabricated membranes and afects dye rejection further, as well as their antifouling performance. In contrast with pristine membrane, PES-GO/TiO2 and PVDF-GO/TiO2 possessed high hydrophilicity, as indicated by their low contact angle (67.38° and 62.12°, respectively). Based on this study, PVDF-GO/TiO2 showed higher porosity value (94.88%), permeability (87.32 L/ m2 hMPa) and MB rejection rate (92.63%), as well as fux recovery ratio value of>100% as compared with others. Overall, the incorporation of GO and TiO2 with PVDF polymer are proven to be efective hybrid materials of membrane fabrication for dye rejection application in the near future. The polymer material’s intrinsic prope

In this work, the role of reduced graphene oxide (rGO) with hyperbranched surfactant and its hybridisation with multiwalled carbon nanotubes (MWCNTs) and platinum (Pt) nanoparticles (NPs) as counter electrode (CE) were investigated to determine the photovoltaic performance of dye-sensitised solar cells (DSSCs). Sodium 1,4-is(neopentyloxy)-3-(neopentyloxycarbonyl)- 1,4-dioxobutane-2-sulphonate (TC14) surfactant was utilised as dispersing and stabilising agent in electrochemical exfoliation to synthesise graphene oxide (GO) as initial solution for rGO production prior to its further hybridisation and fabrication as thin film. A chemical reduction process utilising hydrazine hydrate was conducted to produce rGO due to the low temperature process and water-based GO solution. Subsequently, hybrid solution was prepared by mixing 1 wt% MWCNTs into the produced rGO solution. TC14-rGO and TC14-rGO_MWCNTs hybrid solution were transferred into fluorine-doped tin oxide substrate to fabricate thin film by spraying deposition method. Finally, the CE films were prepared by coating with thin Pt NPs. Photoanode film was prepared by a two-step process: hydrothermal growth method to synthesise titanium dioxide nanowires (TiO2 NWs) and subsequent squeegee method to apply TiO2 NPs. According to solar simulator measurement, the highest energy conversion efficiency (η) was achieved by using CE-based TC14-rGO_MWCNTs/Pt (1.553%), with the highest short current density of 4.424 mA/cm2. The highest η was due to the high conductivity of CE hybrid film and the morphology of fabricated TiO2 NWs/TiO2 NPs. Consequently, the dye adsorption was high, and the photovoltaic performance of DSSCs was increased. This result also showed that rGO and rGO_MWCNTs hybrid can be used as considerable potential candidate materials to replace Pt gradually.