Search

Earth-abundant oxides are promising candidates as effective and low-cost catalysts for the oxygen evolution reaction (OER) in alkaline media, which remains one of the bottlenecks in electrolysis and artificial photosynthesis. A fundamental understanding of the atomic-scale reaction mechanism during OER could drive further progress, but a stable model system has yet to be provided. Here we show that Fe3O4 single crystal surfaces, prepared in ultrahigh vacuum (UHV) are stable in alkaline electrolytein the range pH 7-14 and under OER conditions in 1 M NaOH. Fe3O4(001) and Fe3O4(110) surfaces were studied with X-ray photoelectron spectroscopy, low-energy electron diffraction, and scanning tunneling microscopy in UHV, and atomic force microscopy in air. Fe3O4(110) is found to be more reactive for oxidative water splitting than (001)-oriented magnetite samples. Magnetite is electrically conductive, and the structure and properties of its major facets are well understood in UHV. With these newly obtained results, we propose magnetite (Fe3O4) as a promising model system for further mechanistic studies of electrochemical reactions in alkaline media and under highly oxidizing conditions.

Earth-abundant oxides are promising candidates as effective and low-cost catalysts for the oxygen evolution reaction (OER) in alkaline media, which remains one of the bottlenecks in electrolysis and artificial photosynthesis. A fundamental understanding of the atomic-scale reaction mechanism during OER could drive further progress, but a stable model system has yet to be provided. Here we show that Fe3O4 single crystal surfaces, prepared in ultrahigh vacuum (UHV) are stable in alkaline electrolytein the range pH 7-14 and under OER conditions in 1 M NaOH. Fe3O4(001) and Fe3O4(110) surfaces were studied with X-ray photoelectron spectroscopy, low-energy electron diffraction, and scanning tunneling microscopy in UHV, and atomic force microscopy in air. Fe3O4(110) is found to be more reactive for oxidative water splitting than (001)-oriented magnetite samples. Magnetite is electrically conductive, and the structure and properties of its major facets are well understood in UHV. With these newly obtained results, we propose magnetite (Fe3O4) as a promising model system for further mechanistic studies of electrochemical reactions in alkaline media and under highly oxidizing conditions.

The photoactivity of methanol adsorbed on the anatase TiO2 (101) surface was studied by a combination of scanning tunneling microscopy (STM), temperature-programmed desorption (TPD), X-ray photoemission spectroscopy (XPS), and density functional theory (DFT) calculations. Isolated methanol molecules adsorbed at the anatase (101) surface show a negligible photoactivity. Two ways of methanol activation were found. First, methoxy groups formed by reaction of methanol with coadsorbed O2 molecules or terminal OH groups are photoactive, and they turn into formaldehyde upon UV illumination. The methoxy species show an unusual C 1s core-level shift of 1.4 eV compared to methanol; their chemical assignment was verified by DFT calculations with inclusion of final-state effects. The second way of methanol activation opens at methanol coverages above 0.5 monolayer (ML), and methyl formate is produced in this reaction pathway. The adsorption of methanol in the coverage regime from 0 to 2 ML is described in detail; it is key for understanding the photocatalytic behavior at high coverages. There, a hydrogen-bonding network is established in the adsorbed methanol layer, and consequently, methanol dissociation becomes energetically more favorable. DFT calculations show that dissociation of the methanol molecule is always the key requirement for hole transfer from the substrate to the adsorbed methanol. We show that the hydrogen-bonding network established in the methanol layer dramatically changes the kinetics of proton transfer during the photoreaction.

The rutile TiO2(011) surface exhibits a (2 × 1) reconstruction when prepared by standard techniques in ultrahigh vacuum (UHV). Here we report that a restructuring occurs upon exposing the surface to liquid water at room temperature. The experiment was performed in a dedicated UHV system, equipped for direct and clean transfer of samples between UHV and liquid environment. After exposure to liquid water, an overlayer with a (2 × 1) symmetry was observed containing two dissociated water molecules per unit cell. The two OH groups yield an apparent "c(2 × 1)" symmetry in scanning tunneling microscopy (STM) images. On the basis of STM analysis and density functional theory (DFT) calculations, this overlayer is attributed to dissociated water on top of the unreconstructed (1 × 1) surface. Investigation of possible adsorption structures and analysis of the domain boundaries in this structure provide strong evidence that the original (2 × 1) reconstruction is lifted. Unlike the (2 × 1) reconstruction, the (1 × 1) surface has an appropriate density and symmetry of adsorption sites. The possibility of contaminant-induced restructuring was excluded based on X-ray photoelectron spectroscopy (XPS) and low-energy He+ ion scattering (LEIS) measurements.

Electrochemical surface science of oxides is an emerging field with expected high impact in developing, for instance, rationally designed catalysts. The aim in such catalysts is to replace noble metals by earth-abundant elements, yet without sacrificing activity. Gaining an atomic-level understanding of such systems hinges on the use of experimental surface characterization techniques such as scanning tunneling microscopy (STM), in which tungsten tips have been the most widely used probes, both in vacuum and under electrochemical conditions. Here, we present an in situ STM study with atomic resolution that shows how tungsten(VI) oxide, spontaneously generated at a W STM tip, forms 1D adsorbates on oxide substrates. By comparing the behavior of rutile TiO2(110) and magnetite Fe3O4(001) in aqueous solution, we hypothesize that, below the point of zero charge of the oxide substrate, electrostatics causes water-soluble WO3 to efficiently adsorb and form linear chains in a self-limiting manner up to submonolayer coverage. The 1D oligomers can be manipulated and nanopatterned in situ with a scanning probe tip. As WO3 spontaneously forms under all conditions of potential and pH at the tungsten-aqueous solution interface, this phenomenon also identifies an important caveat regarding the usability of tungsten tips in electrochemical surface science of oxides and other highly adsorptive materials. (Chemical Equation Presented).

The rutile TiO2(011) surface exhibits a (2 × 1) reconstruction when prepared by standard techniques in ultrahigh vacuum (UHV). Here we report that a restructuring occurs upon exposing the surface to liquid water at room temperature. The experiment was performed in a dedicated UHV system, equipped for direct and clean transfer of samples between UHV and liquid environment. After exposure to liquid water, an overlayer with a (2 × 1) symmetry was observed containing two dissociated water molecules per unit cell. The two OH groups yield an apparent "c(2 × 1)" symmetry in scanning tunneling microscopy (STM) images. On the basis of STM analysis and density functional theory (DFT) calculations, this overlayer is attributed to dissociated water on top of the unreconstructed (1 × 1) surface. Investigation of possible adsorption structures and analysis of the domain boundaries in this structure provide strong evidence that the original (2 × 1) reconstruction is lifted. Unlike the (2 × 1) reconstruction, the (1 × 1) surface has an appropriate density and symmetry of adsorption sites. The possibility of contaminant-induced restructuring was excluded based on X-ray photoelectron spectroscopy (XPS) and low-energy He+ ion scattering (LEIS) measurements.

The photoactivity of methanol adsorbed on the anatase TiO2 (101) surface was studied by a combination of scanning tunneling microscopy (STM), temperature-programmed desorption (TPD), X-ray photoemission spectroscopy (XPS), and density functional theory (DFT) calculations. Isolated methanol molecules adsorbed at the anatase (101) surface show a negligible photoactivity. Two ways of methanol activation were found. First, methoxy groups formed by reaction of methanol with coadsorbed O2 molecules or terminal OH groups are photoactive, and they turn into formaldehyde upon UV illumination. The methoxy species show an unusual C 1s core-level shift of 1.4 eV compared to methanol; their chemical assignment was verified by DFT calculations with inclusion of final-state effects. The second way of methanol activation opens at methanol coverages above 0.5 monolayer (ML), and methyl formate is produced in this reaction pathway. The adsorption of methanol in the coverage regime from 0 to 2 ML is described in detail; it is key for understanding the photocatalytic behavior at high coverages. There, a hydrogen-bonding network is established in the adsorbed methanol layer, and consequently, methanol dissociation becomes energetically more favorable. DFT calculations show that dissociation of the methanol molecule is always the key requirement for hole transfer from the substrate to the adsorbed methanol. We show that the hydrogen-bonding network established in the methanol layer dramatically changes the kinetics of proton transfer during the photoreaction.

Formaldehyde (CH2O) adsorption on the anatase TiO2(101) surface was studied with a combination of experimental and theoretical methods. Scanning tunneling microscopy, noncontact atomic force microscopy, temperature-programmed desorption, and X-ray photoelectron spectroscopy were employed on the experimental side. Density functional theory was used to calculate formaldehyde adsorption configurations and energy barriers for transitions between them. At low coverages (<0.25 monolayer), CH2O binds via its oxygen atom to the surface 5-coordinated Ti atoms Ti5c (monodentate configuration). At higher coverages, many adsorption configurations with comparable adsorption energies coexist, including a bidentate configuration and paraformaldehyde chains. The adsorption energies of all possible adsorption configurations lie in the range from 0.6 to 0.8 eV. Upon annealing, all formaldehyde molecules desorb below room temperature; no other reaction products were detected.

High-quality Sn-doped In2O3 (ITO) films were grown epitaxially on yttria stabilized zirconia (111) with oxygen-plasma assisted molecular beam epitaxy (MBE). The 12 nm thick films, containing 2–6% Sn, are fully oxidized. Angle-resolved x-ray photoelectron spectroscopy (ARXPS) confirms that the Sn dopant substitutes In atoms in the bixbyite lattice. From XPS peak shape analysis and spectroscopic ellipsometry measurements it is estimated that, in a film with 6 at.% Sn, ~1/3 of the Sn atoms are electrically active. Reflection high energy electron diffraction (RHEED) shows a flat surface morphology and scanning tunneling microscopy (STM) shows terraces several hundred nanometers in width. The terraces consist of 10 nm wide orientational domains, which are attributed to the initial nucleation of the film. Low energy electron diffraction (LEED) and STM results show a bulk-terminated (1×1) surface, which is supported by first-principles density functional theory (DFT) calculations. Atomically resolved STM images are consistent with Tersoff–Hamann calculations that show that surface In atoms are imaged bright or dark, depending on the configuration of their O neighbors. The coordination of surface atoms on the In2O3(111)–1×1 surface is analyzed in terms of their possible role in surface chemical reactions.