Search

The Grain Impact Analyser and Dust Accumulator (GIADA) instrument onboard Rosetta studied the dust environment of comet 67P/Churyumov–Gerasimenko from 3.7 au inbound, through perihelion, to 3.8 au outbound, measuring the dust flow and the dynamic properties of individual particles. GIADA is composed of three subsystems: (1) Grain Detection System (GDS); (2) Impact Sensor (IS); and (3) Micro-Balances System (MBS). Monitoring the subsystems’ performance during operations is an important element for the correct calibration of scientific measurements. In this paper, we analyse the GIADA inflight calibration data obtained by internal calibration devices for the three subsystems during the period from 1 August 2014 to 31 October 2015. The calibration data testify a nominal behaviour of the instrument during these fifteen months of mission; the only exception is a minor loss of sensitivity for one of the two GDS receivers, attributed to dust contamination.© 2017 COSPAR

The Rosetta probe, orbiting Jupiter-family comet 67P/Churyumov-Gerasimenko, has been detecting individual dust particles of mass larger than 10(-10) kg by means of the GIADA dust collector and the OSIRIS Wide Angle Camera and Narrow Angle Camera since 2014 August and will continue until 2016 September. Detections of single dust particles allow us to estimate the anisotropic dust flux from 67P, infer the dust loss rate and size distribution at the surface of the sunlit nucleus, and see whether the dust size distribution of 67P evolves in time. The velocity of the Rosetta orbiter, relative to 67P, is much lower than the dust velocity measured by GIADA, thus dust counts when GIADA is nadir-pointing will directly provide the dust flux. In OSIRIS observations, the dust flux is derived from the measurement of the dust space density close to the spacecraft. Under the assumption of radial expansion of the dust, observations in the nadir direction provide the distance of the particles by measuring their trail length, with a parallax baseline determined by the motion of the spacecraft. The dust size distribution at sizes > 1 mm observed by OSIRIS is consistent with a differential power index of -4, which was derived from models of 67P's trail. At sizes <1 mm, the size distribution observed by GIADA shows a strong time evolution, with a differential power index drifting from -2 beyond 2 au to -3.7 at perihelion, in agreement with the evolution derived from coma and tail models based on ground-based data. The refractory-to-water mass ratio of the nucleus is close to six during the entire inbound orbit and at perihelion.

Critical measurements for understanding accretion and the dust/gas ratio in the solar nebula, where planets were forming 4.5 billion years ago, are being obtained by the GIADA (Grain Impact Analyser and Dust Accumulator) experiment on the European Space Agency's Rosetta spacecraft orbiting comet 67P/Churyumov-Gerasimenko. Between 3.6 and 3.4 astronomical units inbound, GIADA and OSIRIS (Optical, Spectroscopic, and Infrared Remote Imaging System) detected 35 outflowing grains of mass 10-10 to 10-7 kilograms, and 48 grains of mass 10-5 to 10-2 kilograms, respectively. Combined with gas data from the MIRO (Microwave Instrument for the Rosetta Orbiter) and ROSINA (Rosetta Orbiter Spectrometer for Ion and Neutral Analysis) instruments, we find a dust/gas mass ratio of 4 ± 2 averaged over the sunlit nucleus surface. A cloud of larger grains also encircles the nucleus in bound orbits from the previous perihelion. The largest orbiting clumps are meter-sized, confirming the dust/gas ratio of 3 inferred at perihelion from models of dust comae and trails. © 2015, American Association for the Advancement of Science. All rights reserved.

Any evolving system can change of state via thermal mechanisms (hopping a barrier) or via quantum tunneling. Most of the time, efficient classical mechanisms dominate at high temperatures. This is why an increase of the temperature can initiate the chemistry. We present here an experimental investigation of O-atom diffusion and reactivity on water ice. We explore the 6-25 K temperature range at sub-monolayer surface coverages. We derive the diffusion temperature law and observe the transition from quantum to classical diffusion. Despite of the high mass of O, quantum tunneling is efficient even at 6 K. As a consequence, the solid-state astrochemistry of cold regions should be reconsidered and should include the possibility of forming larger organic molecules than previously expected., Comment: 13 pages, 4 figures

Any evolving system can change of state via thermal mechanisms (hopping a barrier) or via quantum tunneling. Most of the time, efficient classical mechanisms dominate at high temperatures. This is why an increase of the temperature can initiate the chemistry. We present here an experimental investigation of O-atom diffusion and reactivity on water ice. We explore the 6-25 K temperature range at sub-monolayer surface coverages. We derive the diffusion temperature law and observe the transition from quantum to classical diffusion. Despite of the high mass of O, quantum tunneling is efficient even at 6 K. As a consequence, the solid-state astrochemistry of cold regions should be reconsidered and should include the possibility of forming larger organic molecules than previously expected., Comment: 13 pages, 4 figures

The formation of water molecules from the reaction between ozone (O3) and D-atoms is studied experimentally for the first time. Ozone is deposited on non-porous amorphous solid water ice (H2O), and D-atoms are then sent onto the sample held at 10 K. HDO molecules are detected during the desorption of the whole substrate where isotope mixing takes place, indicating that water synthesis has occurred. The efficiency of water formation via hydrogenation of ozone is of the same order of magnitude of that found for reactions involving O atoms or O2 molecules and exhibits no apparent activation barrier. These experiments validate the assumption made by models using ozone as one of the precursors of water formation via solid-state chemistry on interstellar dust grains., Comment: 16 pages, 2 figures, to be published on ApJL

The formation of water molecules from the reaction between ozone (O3) and D-atoms is studied experimentally for the first time. Ozone is deposited on non-porous amorphous solid water ice (H2O), and D-atoms are then sent onto the sample held at 10 K. HDO molecules are detected during the desorption of the whole substrate where isotope mixing takes place, indicating that water synthesis has occurred. The efficiency of water formation via hydrogenation of ozone is of the same order of magnitude of that found for reactions involving O atoms or O2 molecules and exhibits no apparent activation barrier. These experiments validate the assumption made by models using ozone as one of the precursors of water formation via solid-state chemistry on interstellar dust grains., Comment: 16 pages, 2 figures, to be published on ApJL

Comet 67P/Churyumov-Gerasimenko (67P hereinafter) is characterized by a dust transfer from the southern hemi-nucleus to the night-side northern dust deposits, which constrains the dust-to-ices mass ratio inside the nucleus to values a factor of 2 larger than that provided by the lost mass of gas and non-volatiles. This applies to all comets because the gas density in all night comae cannot prevent the dust fallback. Taking into account Grain Impact Analyser and Dust Accumulator (GIADA) data collected during the entire Rosetta mission, we update the average dust bulk density to ρD=785 +520/−115 $\rho {}{}_{\rm D} = 785_{-115}^{+520}$ kg m$^-3$ that, coupled to the 67P nucleus bulk density, confirms an average dust-to-ices mass ratio δ = 7.5 inside 67P. The improved dust densities are consistent with a mixture of (20 ± 8) per cent of ices, (4 ± 1) per cent of Fe sulphides, (22 ± 2) per cent of silicates and (54 ± 5) per cent of hydrocarbons, on average volume abundances. These values correspond to solar chemical abundances, as suggested by the elemental C/Fe ratio observed in 67P. The ice content in 67P matches that inferred in Kuiper belt objects, (20 ± 12) per cent on average volume abundance and suggests a water content in all trans-Neptunian objects lower than in CI chondrites. The 67P icy pebbles and the dust collected by GIADA have a microporosity of (49 ± 5) and (59 ± 8) per cent, respectively.

Solar System formation models predict that the building-blocks of planetesimals were mm- to cm-sized pebbles, aggregates of ices and non-volatile materials, consistent with the compact particles ejected by comet 67P/Churyumov-Gerasimenko (67P hereafter) and detected by GIADA (Grain Impact Analyzer and Dust Accumulator) on-board the Rosetta spacecraft. Planetesimals were formed by the gentle gravitational accretion of pebbles, so that they have an internal macroporosity of 40%. We measure the average dust bulk density ${\rho}D = 795 _{-65}^{+840} kg m^{-3}$ that, coupled to the 67P nucleus bulk density, provides the average dust-to-ices mass ratio δ = 8.5. We find that the measured densities of the 67P pebbles are consistent with a mixture of (15 ± 6)% of ices, (5 ± 2)% of Fe-sulfides, (28 ± 5)% of silicates, and (52 ± 12)% of hydrocarbons, in average volume abundances. This composition matches both the solar and CI-chondritic chemical abundances, thus showing that GIADA has sampled the typical non-volatile composition of the pebbles that formed all planetesimals. The GIADA data do not constrain the abundance of amorphous silicates vs. crystalline Mg,Fe- olivines and pyroxenes. We find that the pebbles have a microporosity of (52 ± 8)% (internal volume filling factor φP = 0.48±0.08), implying an average porosity for the 67P nucleus of (71 ± 8)%, lower than previously estimated.

The Grain Impact Analyser and Dust Accumulator (GIADA) instrument onboard Rosetta studied the dust environment of comet 67P/Churyumov–Gerasimenko from 3.7 au inbound, through perihelion, to 3.8 au outbound, measuring the dust flow and the dynamic properties of individual particles. GIADA is composed of three subsystems: 1) Grain Detection System (GDS); 2) Impact Sensor (IS); and 3) Micro-Balances System (MBS). Monitoring the subsystems’ performance during operations is an important element for the correct calibration of scientific measurements. In this paper, we analyse the GIADA inflight calibration data obtained by internal calibration devices for the three subsystems during the period from 1 August 2014 to 31 October 2015. The calibration data testify a nominal behaviour of the instrument during these fifteen months of mission; the only exception is a minor loss of sensitivity for one of the two GDS receivers, attributed to dust contamination.

GIADA (Grain Impact Analyzer and Dust Accumulator) on-board the Rosetta space probe is designed to measure the momentum, mass and speed of individual dust particles escaping the nucleus of comet 67P/Churyumov-Gerasimenko (hereafter 67P). From August 2014 to June 2016 Rosetta escorted comet 67P during its journey around the Sun. Here we focus on GIADA data taken between 2015 January and 2016 February which included 67P's perihelion passage. To better understand cometary activity and more specifically the presence of dust structures in cometary comae, we mapped the spatial distribution of dust density in 67P's coma. In this manner we could track the evolution of high density regions of coma dust and their connections with nucleus illumination conditions, namely tracking 67P's seasons. We also studied the link between dust particle speeds and their masses with respect to heliocentric distance, i.e. the level of cometary activity. This allowed us to derive a global and a local correlation of the dust particles’ speed distribution with respect to the H2O production rate.

The Rosetta probe, orbiting Jupiter-family comet 67P/Churyumov–Gerasimenko, has been detecting individual dust particles of mass larger than 10^(−10) kg by means of the GIADA dust collector and the OSIRIS Wide Angle Camera and Narrow Angle Camera since 2014 August and will continue until 2016 September. Detections of single dust particles allow us to estimate the anisotropic dust flux from 67P, infer the dust loss rate and size distribution at the surface of the sunlit nucleus, and see whether the dust size distribution of 67P evolves in time. The velocity of the Rosetta orbiter, relative to 67P, is much lower than the dust velocity measured by GIADA, thus dust counts when GIADA is nadir-pointing will directly provide the dust flux. In OSIRIS observations, the dust flux is derived from the measurement of the dust space density close to the spacecraft. Under the assumption of radial expansion of the dust, observations in the nadir direction provide the distance of the particles by measuring their trail length, with a parallax baseline determined by the motion of the spacecraft. The dust size distribution at sizes >1 mm observed by OSIRIS is consistent with a differential power index of −4, which was derived from models of 67P’s trail. At sizes <1 mm, the size distribution observed by GIADA shows a strong time evolution, with a differential power index drifting from −2 beyond 2 au to −3.7 at perihelion, in agreement with the evolution derived from coma and tail models based on ground-based data. The refractory-to-water mass ratio of the nucleus is close to six during the entire inbound orbit and at perihelion.

GIADA (Grain Impact Analyser and Dust Accumulator) on-board the Rosetta mission to comet 67P/Churyumov-Gerasimenko was designed to study the physical and dynamical properties of dust particles ejected by the comet during the encounter. In this paper we report the results of the analysis of data collected by GIADA during the past seven years of the cruise phase. During this period the GIADA detection subsystems were switched on for periodic in-flight payload checkouts to monitor their state of-health including potential changes in its performance that could affect its data collection. Only slight variations in sensitivity and dynamical range were identified that will not affect the GIADA measurement capability during the Rosetta comet encounter and rendezvous phase. The GIADA microbalance system detected the presence of low-volatility material over a period of about 169 days when the GIADA cover remained partially opened. It is highly probable that this material originated from the spacecraft itself, as a spacecraft’s outgassing was observed by the ROSINA mass spectrometer (on-board Rosetta) during the cruise phase. The identification of the low-volatility mass deposited on the microbalances as self-contamination will allow us to evaluate the mass rate background to be subtracted from the GIADA science data. These results obtained from GIADA cruise data analysis coupled with laboratory calibration data obtained from measurements using the GIADA spare model for selected cometary dust analogs will be the basis for the interpretation of the GIADA scientific data.

The Grain Impact Analyzer and Dust Accumulator (GIADA) instrument on board ESA’s Rosetta mission is constraining the origin of the dust particles detected within the coma of comet 67 P/Churyumov–Gerasimenko (67P). The collected particles belong to two families: (i) compact particles (ranging in size from 0.03 to 1 mm), witnessing the presence of materials that underwent processing within the solar nebula and (ii) fluffy aggregates (ranging in size from 0.2 to 2.5 mm) of sub-micron grains that may be a record of a primitive component, probably linked to interstellar dust. The dynamics of the fluffy aggregates constrain their equivalent bulk density to <1 kg m-3. These aggregates are charged, fragmented, and decelerated by the spacecraft negative potential and enter GIADA in showers of fragments at speeds <1 m s-1. The density of such optically thick aggregates is consistent with the low bulk density of the nucleus. The mass contribution of the fluffy aggregates to the refractory component of the nucleus is negligible and their coma brightness contribution is less than 15%.

Context. During the period between 15 September 2014 and 4 February 2015, the Rosetta spacecraft accomplished the circular orbit phase around the nucleus of comet 67P/Churyumov-Gerasimenko (67P). The Grain Impact Analyzer and Dust Accumulator (GIADA) onboard Rosetta monitored the 67P coma dust environment for the entire period. Aims. We aim to describe the dust spatial distribution in the coma of comet 67P by means of in situ measurements. We determine dynamical and physical properties of cometary dust particles to support the study of the production process and dust environment modification. Methods. We analyzed GIADA data with respect to the observation geometry and heliocentric distance to describe the coma dust spatial distribution of 67P, to monitor its activity, and to retrieve information on active areas present on its nucleus. We combined GIADA detection information with calibration activity to distinguish different types of particles that populate the coma of 67P: compact particles and fluffy porous aggregates. By means of particle dynamical parameters measured by GIADA, we studied the dust acceleration region. Results. GIADA was able to distinguish different types of particles populating the coma of 67P: compact particles and fluffy porous aggregates. Most of the compact particle detections occurred at latitudes and longitudes where the spacecraft was in view of the comet’s neck region of the nucleus, the so-called Hapi region. This resulted in an oscillation of the compact particle abundance with respect to the spacecraft position and a global increase as the comet moved from 3.36 to 2.43 AU heliocentric distance. The speed of these particles, having masses from 10-10 to 10-7 kg, ranged from 0.3 to 12.2 m s−1. The variation of particle mass and speed distribution with respect to the distance from the nucleus gave indications of the dust acceleration region. The influen

The Grain Impact Analyser and Dust Accumulator (GIADA) instrument onboard Rosetta studied the dust environment of comet 67P/Churyumov–Gerasimenko from 3.7 au inbound, through perihelion, to 3.8 au outbound, measuring the dust flow and the dynamic properties of individual particles. GIADA is composed of three subsystems: 1) Grain Detection System (GDS); 2) Impact Sensor (IS); and 3) Micro-Balances System (MBS). Monitoring the subsystems’ performance during operations is an important element for the correct calibration of scientific measurements. In this paper, we analyse the GIADA inflight calibration data obtained by internal calibration devices for the three subsystems during the period from 1 August 2014 to 31 October 2015. The calibration data testify a nominal behaviour of the instrument during these fifteen months of mission; the only exception is a minor loss of sensitivity for one of the two GDS receivers, attributed to dust contamination.

GIADA (Grain Impact Analyzer and Dust Accumulator) on-board the Rosetta space probe is designed to measure the momentum, mass and speed of individual dust particles escaping the nucleus of comet 67P/Churyumov-Gerasimenko (hereafter 67P). From August 2014 to June 2016 Rosetta escorted comet 67P during its journey around the Sun. Here we focus on GIADA data taken between 2015 January and 2016 February which included 67P's perihelion passage. To better understand cometary activity and more specifically the presence of dust structures in cometary comae, we mapped the spatial distribution of dust density in 67P's coma. In this manner we could track the evolution of high density regions of coma dust and their connections with nucleus illumination conditions, namely tracking 67P's seasons. We also studied the link between dust particle speeds and their masses with respect to heliocentric distance, i.e. the level of cometary activity. This allowed us to derive a global and a local correlation of the dust particles’ speed distribution with respect to the H2O production rate.

The Grain Impact Analyzer and Dust Accumulator (GIADA) instrument on board ESA’s Rosetta mission is constraining the origin of the dust particles detected within the coma of comet 67 P/Churyumov–Gerasimenko (67P). The collected particles belong to two families: (i) compact particles (ranging in size from 0.03 to 1 mm), witnessing the presence of materials that underwent processing within the solar nebula and (ii) fluffy aggregates (ranging in size from 0.2 to 2.5 mm) of sub-micron grains that may be a record of a primitive component, probably linked to interstellar dust. The dynamics of the fluffy aggregates constrain their equivalent bulk density to <1 kg m-3. These aggregates are charged, fragmented, and decelerated by the spacecraft negative potential and enter GIADA in showers of fragments at speeds <1 m s-1. The density of such optically thick aggregates is consistent with the low bulk density of the nucleus. The mass contribution of the fluffy aggregates to the refractory component of the nucleus is negligible and their coma brightness contribution is less than 15%.

The Rosetta probe, orbiting Jupiter-family comet 67P/Churyumov–Gerasimenko, has been detecting individual dust particles of mass larger than 10^(−10) kg by means of the GIADA dust collector and the OSIRIS Wide Angle Camera and Narrow Angle Camera since 2014 August and will continue until 2016 September. Detections of single dust particles allow us to estimate the anisotropic dust flux from 67P, infer the dust loss rate and size distribution at the surface of the sunlit nucleus, and see whether the dust size distribution of 67P evolves in time. The velocity of the Rosetta orbiter, relative to 67P, is much lower than the dust velocity measured by GIADA, thus dust counts when GIADA is nadir-pointing will directly provide the dust flux. In OSIRIS observations, the dust flux is derived from the measurement of the dust space density close to the spacecraft. Under the assumption of radial expansion of the dust, observations in the nadir direction provide the distance of the particles by measuring their trail length, with a parallax baseline determined by the motion of the spacecraft. The dust size distribution at sizes >1 mm observed by OSIRIS is consistent with a differential power index of −4, which was derived from models of 67P’s trail. At sizes <1 mm, the size distribution observed by GIADA shows a strong time evolution, with a differential power index drifting from −2 beyond 2 au to −3.7 at perihelion, in agreement with the evolution derived from coma and tail models based on ground-based data. The refractory-to-water mass ratio of the nucleus is close to six during the entire inbound orbit and at perihelion.

Context. During the period between 15 September 2014 and 4 February 2015, the Rosetta spacecraft accomplished the circular orbit phase around the nucleus of comet 67P/Churyumov-Gerasimenko (67P). The Grain Impact Analyzer and Dust Accumulator (GIADA) onboard Rosetta monitored the 67P coma dust environment for the entire period. Aims. We aim to describe the dust spatial distribution in the coma of comet 67P by means of in situ measurements. We determine dynamical and physical properties of cometary dust particles to support the study of the production process and dust environment modification. Methods. We analyzed GIADA data with respect to the observation geometry and heliocentric distance to describe the coma dust spatial distribution of 67P, to monitor its activity, and to retrieve information on active areas present on its nucleus. We combined GIADA detection information with calibration activity to distinguish different types of particles that populate the coma of 67P: compact particles and fluffy porous aggregates. By means of particle dynamical parameters measured by GIADA, we studied the dust acceleration region. Results. GIADA was able to distinguish different types of particles populating the coma of 67P: compact particles and fluffy porous aggregates. Most of the compact particle detections occurred at latitudes and longitudes where the spacecraft was in view of the comet’s neck region of the nucleus, the so-called Hapi region. This resulted in an oscillation of the compact particle abundance with respect to the spacecraft position and a global increase as the comet moved from 3.36 to 2.43 AU heliocentric distance. The speed of these particles, having masses from 10-10 to 10-7 kg, ranged from 0.3 to 12.2 m s−1. The variation of particle mass and speed distribution with respect to the distance from the nucleus gave indications of the dust acceleration region. The influen

GIADA (Grain Impact Analyser and Dust Accumulator) on-board the Rosetta mission to comet 67P/Churyumov-Gerasimenko was designed to study the physical and dynamical properties of dust particles ejected by the comet during the encounter. In this paper we report the results of the analysis of data collected by GIADA during the past seven years of the cruise phase. During this period the GIADA detection subsystems were switched on for periodic in-flight payload checkouts to monitor their state of-health including potential changes in its performance that could affect its data collection. Only slight variations in sensitivity and dynamical range were identified that will not affect the GIADA measurement capability during the Rosetta comet encounter and rendezvous phase. The GIADA microbalance system detected the presence of low-volatility material over a period of about 169 days when the GIADA cover remained partially opened. It is highly probable that this material originated from the spacecraft itself, as a spacecraft’s outgassing was observed by the ROSINA mass spectrometer (on-board Rosetta) during the cruise phase. The identification of the low-volatility mass deposited on the microbalances as self-contamination will allow us to evaluate the mass rate background to be subtracted from the GIADA science data. These results obtained from GIADA cruise data analysis coupled with laboratory calibration data obtained from measurements using the GIADA spare model for selected cometary dust analogs will be the basis for the interpretation of the GIADA scientific data.