Search

Hydromulch spreading as a crop and land management technique might show important advantages over plastic films. Pulp from recovered paper and cardboard coming from paper mills, blended with several additives to develop biodegradable hydromulches, could be spread for weed control in perennial crops such as fruit orchards and vineyards. In the present work, 24 blends were prepared by mixing paper pulp with different additives: (a) wheat straw, rice hulls, and substrate used for mushroom cultivation on the one hand as fillers, and (b) rice bran, white glue, sodium silicate and powered gypsum on the other hand as agglomerating agents. The blends were tested with a texture analyser to evaluate their mechanical properties, testing the puncture resistance (24 blends) and the tensile strength (15 blends). Scanning electron photomicrographs of some blends were obtained in order to explore the relationship between their components and the mechanical properties. The results indicate the advisability of using a blend prepared with paper pulp, wheat straw (sieved at 2.5 mm) and gypsum. An environmentally controlled experiment was performed on this and another hydromulch in which rice husk substituted wheat straw to evaluate their efficiency for reducing seedling weed emergence, using propagules of four common summer weeds. The barrier effect of the hydromulches reduced seedling emergence from 64.6% to 95.9%. In general, the percentage of dead seedlings underneath was greater than that which passed through the barrier, making the hydromulches promising tools for preventing seedling emergence and for managing the weed seed bank in field conditions., Postprint (updated version)

Lithium-sulfur (Li-S) battery is next generation battery technology but it's commercialization is obstructed primarily due to the shuttling effect of lithium polysulfides (LiPSs). Herein, we report an effective approach using pencil coated pyrolyzed cellulose filter paper as an interlayer to suppress the LiPSs dissolution into the electrolyte and thus allowing effective utilization of active sulfur cathode. Here, the binder clay particles (mainly SiO2) of pencil graphite facilitate the adsorption of LiPSs, whereas graphite increases the electrical conductivity and acts as a physical barrier to LiPSs. To investigate further, we utilize three different grades of pencil (4B, HB, 5H) which vary in terms of clay (SiO2) composition. It is observed that the HB pencil coated interlayer has the right balance of silica and graphite, which results in an impressive initial capacity of 1352 and 995 mAh g−1 at the current density of 0.1 and 0.5 A g−1, respectively. The cell exhibit high cycling stability of 900 mAh g−1 at 1 A g−1 (3.0 C) for 350 cycles with a slow capacity decay of 0.07% per cycle. The phenomenon of LiPSs adsorption is further understood using post-cycling analysis, H-cell adsorption testing, and shuttle factor calculation for the development of commercial Li-S batteries. © 2020 Elsevier B.V.

Lithium-sulfur (Li-S) battery is next generation battery technology but it's commercialization is obstructed primarily due to the shuttling effect of lithium polysulfides (LiPSs). Herein, we report an effective approach using pencil coated pyrolyzed cellulose filter paper as an interlayer to suppress the LiPSs dissolution into the electrolyte and thus allowing effective utilization of active sulfur cathode. Here, the binder clay particles (mainly SiO2) of pencil graphite facilitate the adsorption of LiPSs, whereas graphite increases the electrical conductivity and acts as a physical barrier to LiPSs. To investigate further, we utilize three different grades of pencil (4B, HB, 5H) which vary in terms of clay (SiO2) composition. It is observed that the HB pencil coated interlayer has the right balance of silica and graphite, which results in an impressive initial capacity of 1352 and 995 mAh g−1 at the current density of 0.1 and 0.5 A g−1, respectively. The cell exhibit high cycling stability of 900 mAh g−1 at 1 A g−1 (3.0 C) for 350 cycles with a slow capacity decay of 0.07% per cycle. The phenomenon of LiPSs adsorption is further understood using post-cycling analysis, H-cell adsorption testing, and shuttle factor calculation for the development of commercial Li-S batteries. © 2020 Elsevier B.V.

Lithium-sulfur (Li-S) battery is next generation battery technology but it's commercialization is obstructed primarily due to the shuttling effect of lithium polysulfides (LiPSs). Herein, we report an effective approach using pencil coated pyrolyzed cellulose filter paper as an interlayer to suppress the LiPSs dissolution into the electrolyte and thus allowing effective utilization of active sulfur cathode. Here, the binder clay particles (mainly SiO2) of pencil graphite facilitate the adsorption of LiPSs, whereas graphite increases the electrical conductivity and acts as a physical barrier to LiPSs. To investigate further, we utilize three different grades of pencil (4B, HB, 5H) which vary in terms of clay (SiO2) composition. It is observed that the HB pencil coated interlayer has the right balance of silica and graphite, which results in an impressive initial capacity of 1352 and 995 mAh g−1 at the current density of 0.1 and 0.5 A g−1, respectively. The cell exhibit high cycling stability of 900 mAh g−1 at 1 A g−1 (3.0 C) for 350 cycles with a slow capacity decay of 0.07% per cycle. The phenomenon of LiPSs adsorption is further understood using post-cycling analysis, H-cell adsorption testing, and shuttle factor calculation for the development of commercial Li-S batteries. © 2020 Elsevier B.V.

Lithium-sulfur (Li-S) battery is next generation battery technology but it's commercialization is obstructed primarily due to the shuttling effect of lithium polysulfides (LiPSs). Herein, we report an effective approach using pencil coated pyrolyzed cellulose filter paper as an interlayer to suppress the LiPSs dissolution into the electrolyte and thus allowing effective utilization of active sulfur cathode. Here, the binder clay particles (mainly SiO2) of pencil graphite facilitate the adsorption of LiPSs, whereas graphite increases the electrical conductivity and acts as a physical barrier to LiPSs. To investigate further, we utilize three different grades of pencil (4B, HB, 5H) which vary in terms of clay (SiO2) composition. It is observed that the HB pencil coated interlayer has the right balance of silica and graphite, which results in an impressive initial capacity of 1352 and 995 mAh g−1 at the current density of 0.1 and 0.5 A g−1, respectively. The cell exhibit high cycling stability of 900 mAh g−1 at 1 A g−1 (3.0 C) for 350 cycles with a slow capacity decay of 0.07% per cycle. The phenomenon of LiPSs adsorption is further understood using post-cycling analysis, H-cell adsorption testing, and shuttle factor calculation for the development of commercial Li-S batteries. © 2020 Elsevier B.V.

Antibiotic resistance (AR) is becoming a worldwide threat due to the increasing occurrence of antibiotic-resistant pathogenic bacterial strains. There is a general consensus about the potential implications of the use of antibiotics in livestock on the onset of antibiotic resistant bacteria (ARB), mainly through meat consumption. However, the ever-increasing use of reclaimed wastewater (RWW) in agriculture may also contribute significantly to the non-accounted exposure to antibiotics, ARB, and antibiotic resistance genes (ARGs). This position paper aims at evaluating the current knowledge concerning the occurrence of antibiotics, ARBs, and ARGs in edible parts of different common crops irrigated with RWW. We will discuss which regulations on the use of RWW may contribute to the minimization of the prevalence of these contaminants in crops, and provide recommendations on how to minimize the impact of these practices.

© 2020 The Authors Integrated geographic modelling and simulation is a computational means to improve understanding of the environment. With the development of Service Oriented Architecture (SOA) and web technologies, it is possible to conduct open, extensible integrated geographic modelling across a network in which resources can be accessed and integrated, and further distributed geographic simulations can be performed. This open web-distributed modelling and simulation approach is likely to enhance the use of existing resources and can attract diverse participants. With this approach, participants from different physical locations or domains of expertise can perform comprehensive modelling and simulation tasks collaboratively. This paper reviews past integrated modelling and simulation systems, highlighting the associated development challenges when moving to an open web-distributed system. A conceptual framework is proposed to introduce a roadmap from a system design perspective, with potential use cases provided. The four components of this conceptual framework - a set of standards, a resource sharing environment, a collaborative integrated modelling environment, and a distributed simulation environment - are also discussed in detail with the goal of advancing this emerging field.

Epithelioid hemangioendothelioma (EHE) is an ultra-rare, translocated, vascular sarcoma. EHE clinical behavior is variable, ranging from that of a low-grade malignancy to that of a high-grade sarcoma and it is marked by a high propensity for systemic involvement. No active systemic agents are currently approved specifically for EHE, which is typically refractory to the antitumor drugs used in sarcomas. The degree of uncertainty in selecting the most appropriate therapy for EHE patients and the lack of guidelines on the clinical management of the disease make the adoption of new treatments inconsistent across the world, resulting in suboptimal outcomes for many EHE patients. To address the shortcoming, a global consensus meeting was organized in December 2020 under the umbrella of the European Society for Medical Oncology (ESMO) involving >80 experts from several disciplines from Europe, North America and Asia, together with a patient representative from the EHE Group, a global, disease-specific patient advocacy group, and Sarcoma Patient EuroNet (SPAEN). The meeting was aimed at defining, by consensus, evidence-based best practices for the optimal approach to primary and metastatic EHE. The consensus achieved during that meeting is the subject of the present publication.

[This corrects the article DOI: 10.1016/j.waojou.2019.100080.].

Proteins play a crucial role in metabolism, in maintaining fluid and acid-base balance and antibody synthesis. Dietary proteins are important nutrients and are classified into: 1) animal proteins (meat, fish, poultry, eggs and dairy), and, 2) plant proteins (legumes, nuts and soy). Dietary modification is one of the most important lifestyle changes that has been shown to significantly decrease the risk of cardiovascular (CV) disease (CVD) by attenuating related risk factors. The CVD burden is reduced by optimum diet through replacement of unprocessed meat with low saturated fat, animal proteins and plant proteins. In view of the available evidence, it has become acceptable to emphasize the role of optimum nutrition to maintain arterial and CV health. Such healthy diets are thought to increase satiety, facilitate weight loss, and improve CV risk. Different studies have compared the benefits of omnivorous and vegetarian diets. Animal protein related risk has been suggested to be greater with red or processed meat over and above poultry, fish and nuts, which carry a lower risk for CVD. In contrast, others have shown no association of red meat intake with CVD. The aim of this expert opinion recommendation was to elucidate the different impact of animal vs vegetable protein on modifying cardiometabolic risk factors. Many observational and interventional studies confirmed that increasing protein intake, especially plant-based proteins and certain animal-based proteins (poultry, fish, unprocessed red meat low in saturated fats and low-fat dairy products) have a positive effect in modifying cardiometabolic risk factors. Red meat intake correlates with increased CVD risk, mainly because of its non-protein ingredients (saturated fats). However, the way red meat is cooked and preserved matters. Thus, it is recommended to substitute red meat with poultry or fish in order to lower CVD risk. Specific amino acids have favourable results in modifying major risk factors for CVD, suc

Epithelioid hemangioendothelioma (EHE) is an ultra-rare, translocated, vascular sarcoma. EHE clinical behavior is variable, ranging from that of a low-grade malignancy to that of a high-grade sarcoma and it is marked by a high propensity for systemic involvement. No active systemic agents are currently approved specifically for EHE, which is typically refractory to the antitumor drugs used in sarcomas. The degree of uncertainty in selecting the most appropriate therapy for EHE patients and the lack of guidelines on the clinical management of the disease make the adoption of new treatments inconsistent across the world, resulting in suboptimal outcomes for many EHE patients. To address the shortcoming, a global consensus meeting was organized in December 2020 under the umbrella of the European Society for Medical Oncology (ESMO) involving >80 experts from several disciplines from Europe, North America and Asia, together with a patient representative from the EHE Group, a global, disease-specific patient advocacy group, and Sarcoma Patient EuroNet (SPAEN). The meeting was aimed at defining, by consensus, evidence-based best practices for the optimal approach to primary and metastatic EHE. The consensus achieved during that meeting is the subject of the present publication.

Pandemics are a recurring theme in human history, with evidence from the beginning of civilization up to the current Corona virus disease 2019 (COVID-19) pandemic. The genotype of the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus that has paralyzed the entire world since early 2020 is most closely related to a coronavirus from bats, eventually passed via Pangolins, although is not identical (Zhu et al., 2020). One of the most accredited hypotheses is that the virus first infected a human at or near a wet market in Wuhan, in the Hubei region of China; this city was the epicenter of the outbreak. In spite of some dis-information which circulates in the social media, it is clear that the virus originates in the over-exploitation of a wildlife at risk of transmission of diseases to humans and, moreover, in danger of extinction. In spite of the very numerous alerts which have been given in the past about the risk of a major outbreak coming from bats which host a high number of SARS viruses, the uncontrolled use of wildlife as a source of meat, bones, scales, blood, horns, hair and many other tissues has never ceased. These products, coming from poaching of endangered and not farmed species, feed both un-official and official markets of food or/and pharmacopeia. We should clearly affirm here that these processes should stop in a near future as they are not only destroying biodiversity but also producing pandemics which have major socio-economical consequences.

Pandemics are a recurring theme in human history, with evidence from the beginning of civilization up to the current Corona virus disease 2019 (COVID-19) pandemic. The genotype of the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus that has paralyzed the entire world since early 2020 is most closely related to a coronavirus from bats, eventually passed via Pangolins, although is not identical (Zhu et al., 2020). One of the most accredited hypotheses is that the virus first infected a human at or near a wet market in Wuhan, in the Hubei region of China; this city was the epicenter of the outbreak. In spite of some dis-information which circulates in the social media, it is clear that the virus originates in the over-exploitation of a wildlife at risk of transmission of diseases to humans and, moreover, in danger of extinction. In spite of the very numerous alerts which have been given in the past about the risk of a major outbreak coming from bats which host a high number of SARS viruses, the uncontrolled use of wildlife as a source of meat, bones, scales, blood, horns, hair and many other tissues has never ceased. These products, coming from poaching of endangered and not farmed species, feed both un-official and official markets of food or/and pharmacopeia. We should clearly affirm here that these processes should stop in a near future as they are not only destroying biodiversity but also producing pandemics which have major socio-economical consequences.

Epithelioid hemangioendothelioma (EHE) is an ultra-rare, translocated, vascular sarcoma. EHE clinical behavior is variable, ranging from that of a low-grade malignancy to that of a high-grade sarcoma and it is marked by a high propensity for systemic involvement. No active systemic agents are currently approved specifically for EHE, which is typically refractory to the antitumor drugs used in sarcomas. The degree of uncertainty in selecting the most appropriate therapy for EHE patients and the lack of guidelines on the clinical management of the disease make the adoption of new treatments inconsistent across the world, resulting in suboptimal outcomes for many EHE patients. To address the shortcoming, a global consensus meeting was organized in December 2020 under the umbrella of the European Society for Medical Oncology (ESMO) involving >80 experts from several disciplines from Europe, North America and Asia, together with a patient representative from the EHE Group, a global, disease-specific patient advocacy group, and Sarcoma Patient EuroNet (SPAEN). The meeting was aimed at defining, by consensus, evidence-based best practices for the optimal approach to primary and metastatic EHE. The consensus achieved during that meeting is the subject of the present publication.

Epithelioid hemangioendothelioma (EHE) is an ultra-rare, translocated, vascular sarcoma. EHE clinical behavior is variable, ranging from that of a low-grade malignancy to that of a high-grade sarcoma and it is marked by a high propensity for systemic involvement. No active systemic agents are currently approved specifically for EHE, which is typically refractory to the antitumor drugs used in sarcomas. The degree of uncertainty in selecting the most appropriate therapy for EHE patients and the lack of guidelines on the clinical management of the disease make the adoption of new treatments inconsistent across the world, resulting in suboptimal outcomes for many EHE patients. To address the shortcoming, a global consensus meeting was organized in December 2020 under the umbrella of the European Society for Medical Oncology (ESMO) involving >80 experts from several disciplines from Europe, North America and Asia, together with a patient representative from the EHE Group, a global, disease-specific patient advocacy group, and Sarcoma Patient EuroNet (SPAEN). The meeting was aimed at defining, by consensus, evidence-based best practices for the optimal approach to primary and metastatic EHE. The consensus achieved during that meeting is the subject of the present publication.

Epithelioid hemangioendothelioma (EHE) is an ultra-rare, translocated, vascular sarcoma. EHE clinical behavior is variable, ranging from that of a low-grade malignancy to that of a high-grade sarcoma and it is marked by a high propensity for systemic involvement. No active systemic agents are currently approved specifically for EHE, which is typically refractory to the antitumor drugs used in sarcomas. The degree of uncertainty in selecting the most appropriate therapy for EHE patients and the lack of guidelines on the clinical management of the disease make the adoption of new treatments inconsistent across the world, resulting in suboptimal outcomes for many EHE patients. To address the shortcoming, a global consensus meeting was organized in December 2020 under the umbrella of the European Society for Medical Oncology (ESMO) involving >80 experts from several disciplines from Europe, North America and Asia, together with a patient representative from the EHE Group, a global, disease-specific patient advocacy group, and Sarcoma Patient EuroNet (SPAEN). The meeting was aimed at defining, by consensus, evidence-based best practices for the optimal approach to primary and metastatic EHE. The consensus achieved during that meeting is the subject of the present publication.

Magnetic resonance imaging (MRI) is the most important paraclinical tool for assessing drug response in multiple sclerosis (MS) clinical trials. As such, MRI has also been widely used in preclinical research to investigate drug efficacy and pathogenic aspects in MS animal models. Keeping track of all published preclinical imaging studies, and possible new therapeutic approaches, has become difficult considering the abundance of studies. Moreover, comparisons between studies are hampered by methodological differences, especially since small differences in an MRI protocol can lead to large differences in tissue contrast. We therefore provide a comprehensive qualitative overview of preclinical MRI studies in the field of neuroinflammatory and demyelinating diseases, aiming to summarize experimental setup, MRI methodology, and risk of bias. We also provide estimates of the effects of tested therapeutic interventions by a meta-analysis. Finally, to improve the standardization of preclinical experiments, we propose guidelines on technical aspects of MRI and reporting that can serve as a framework for future preclinical studies using MRI in MS animal models. By implementing these guidelines, clinical translation of findings will be facilitated, and could possibly reduce experimental animal numbers.

The deposition of chemical reagent inks on paper is a crucial step in the development and fabrication of microfluidic paper-based analytical devices (mu PADs). A pen-plotting approach, delivering chemical ink deposition using technical pens filled with reagents and inserted into a desktop electronic plotter, is shown herein to be a versatile, low-cost, simple, rapid, reproducible, and high-throughput solution. The volume of the deposited ink was quantified gravimetrically, confirming that nanoliter volumes of reagents can be deposited reproducibly (e.g. 7.55 +/- 0.37 nL/mm for a plotting speed of 10 cm/s) in detection zones of mu PADs, typically spatially defined using wax printing. This approach was further investigated with regard to deposition of reagents in different geometrical forms (circular and linear), so demonstrating its applicability for preparation of mu PADs with flexible design and application. By adjusting the plotting speed for linear deposition, lines with a relatively large range of widths (approximate to 628-1192 mm) were created. Circular deposition was also demonstrated via delivery of reagents within wax printed circular fluidic barriers of a range of diameters (inner diameter = 1.5-7 mm). These capabilities were practically demonstrated via the fabrication of mu PADs, based upon differing detection principles for determination of aluminum in natural waters using Morin as the fluorescent reagent. Traditional mu PADs based on digital image colorimetry (DIC) were produced using circular deposition, whilst distance-based mu PADs exploited linear deposition. Both types of mu PADs developed using this method showed excellent precision for determination of trace concentrations of aluminium (average RSDs = 3.38% and 6.45%, and LODs = 0.5 ng (0.25 ppm) and 2 ng (0.5 ppm), for traditional and distance-based detection, respectively).

The deposition of chemical reagent inks on paper is a crucial step in the development and fabrication of microfluidic paper-based analytical devices (mu PADs). A pen-plotting approach, delivering chemical ink deposition using technical pens filled with reagents and inserted into a desktop electronic plotter, is shown herein to be a versatile, low-cost, simple, rapid, reproducible, and high-throughput solution. The volume of the deposited ink was quantified gravimetrically, confirming that nanoliter volumes of reagents can be deposited reproducibly (e.g. 7.55 +/- 0.37 nL/mm for a plotting speed of 10 cm/s) in detection zones of mu PADs, typically spatially defined using wax printing. This approach was further investigated with regard to deposition of reagents in different geometrical forms (circular and linear), so demonstrating its applicability for preparation of mu PADs with flexible design and application. By adjusting the plotting speed for linear deposition, lines with a relatively large range of widths (approximate to 628-1192 mm) were created. Circular deposition was also demonstrated via delivery of reagents within wax printed circular fluidic barriers of a range of diameters (inner diameter = 1.5-7 mm). These capabilities were practically demonstrated via the fabrication of mu PADs, based upon differing detection principles for determination of aluminum in natural waters using Morin as the fluorescent reagent. Traditional mu PADs based on digital image colorimetry (DIC) were produced using circular deposition, whilst distance-based mu PADs exploited linear deposition. Both types of mu PADs developed using this method showed excellent precision for determination of trace concentrations of aluminium (average RSDs = 3.38% and 6.45%, and LODs = 0.5 ng (0.25 ppm) and 2 ng (0.5 ppm), for traditional and distance-based detection, respectively).

The deposition of chemical reagent inks on paper is a crucial step in the development and fabrication of microfluidic paper-based analytical devices (mu PADs). A pen-plotting approach, delivering chemical ink deposition using technical pens filled with reagents and inserted into a desktop electronic plotter, is shown herein to be a versatile, low-cost, simple, rapid, reproducible, and high-throughput solution. The volume of the deposited ink was quantified gravimetrically, confirming that nanoliter volumes of reagents can be deposited reproducibly (e.g. 7.55 +/- 0.37 nL/mm for a plotting speed of 10 cm/s) in detection zones of mu PADs, typically spatially defined using wax printing. This approach was further investigated with regard to deposition of reagents in different geometrical forms (circular and linear), so demonstrating its applicability for preparation of mu PADs with flexible design and application. By adjusting the plotting speed for linear deposition, lines with a relatively large range of widths (approximate to 628-1192 mm) were created. Circular deposition was also demonstrated via delivery of reagents within wax printed circular fluidic barriers of a range of diameters (inner diameter = 1.5-7 mm). These capabilities were practically demonstrated via the fabrication of mu PADs, based upon differing detection principles for determination of aluminum in natural waters using Morin as the fluorescent reagent. Traditional mu PADs based on digital image colorimetry (DIC) were produced using circular deposition, whilst distance-based mu PADs exploited linear deposition. Both types of mu PADs developed using this method showed excellent precision for determination of trace concentrations of aluminium (average RSDs = 3.38% and 6.45%, and LODs = 0.5 ng (0.25 ppm) and 2 ng (0.5 ppm), for traditional and distance-based detection, respectively).

The deposition of chemical reagent inks on paper is a crucial step in the development and fabrication of microfluidic paper-based analytical devices (mu PADs). A pen-plotting approach, delivering chemical ink deposition using technical pens filled with reagents and inserted into a desktop electronic plotter, is shown herein to be a versatile, low-cost, simple, rapid, reproducible, and high-throughput solution. The volume of the deposited ink was quantified gravimetrically, confirming that nanoliter volumes of reagents can be deposited reproducibly (e.g. 7.55 +/- 0.37 nL/mm for a plotting speed of 10 cm/s) in detection zones of mu PADs, typically spatially defined using wax printing. This approach was further investigated with regard to deposition of reagents in different geometrical forms (circular and linear), so demonstrating its applicability for preparation of mu PADs with flexible design and application. By adjusting the plotting speed for linear deposition, lines with a relatively large range of widths (approximate to 628-1192 mm) were created. Circular deposition was also demonstrated via delivery of reagents within wax printed circular fluidic barriers of a range of diameters (inner diameter = 1.5-7 mm). These capabilities were practically demonstrated via the fabrication of mu PADs, based upon differing detection principles for determination of aluminum in natural waters using Morin as the fluorescent reagent. Traditional mu PADs based on digital image colorimetry (DIC) were produced using circular deposition, whilst distance-based mu PADs exploited linear deposition. Both types of mu PADs developed using this method showed excellent precision for determination of trace concentrations of aluminium (average RSDs = 3.38% and 6.45%, and LODs = 0.5 ng (0.25 ppm) and 2 ng (0.5 ppm), for traditional and distance-based detection, respectively).

The deposition of chemical reagent inks on paper is a crucial step in the development and fabrication of microfluidic paper-based analytical devices (mu PADs). A pen-plotting approach, delivering chemical ink deposition using technical pens filled with reagents and inserted into a desktop electronic plotter, is shown herein to be a versatile, low-cost, simple, rapid, reproducible, and high-throughput solution. The volume of the deposited ink was quantified gravimetrically, confirming that nanoliter volumes of reagents can be deposited reproducibly (e.g. 7.55 +/- 0.37 nL/mm for a plotting speed of 10 cm/s) in detection zones of mu PADs, typically spatially defined using wax printing. This approach was further investigated with regard to deposition of reagents in different geometrical forms (circular and linear), so demonstrating its applicability for preparation of mu PADs with flexible design and application. By adjusting the plotting speed for linear deposition, lines with a relatively large range of widths (approximate to 628-1192 mm) were created. Circular deposition was also demonstrated via delivery of reagents within wax printed circular fluidic barriers of a range of diameters (inner diameter = 1.5-7 mm). These capabilities were practically demonstrated via the fabrication of mu PADs, based upon differing detection principles for determination of aluminum in natural waters using Morin as the fluorescent reagent. Traditional mu PADs based on digital image colorimetry (DIC) were produced using circular deposition, whilst distance-based mu PADs exploited linear deposition. Both types of mu PADs developed using this method showed excellent precision for determination of trace concentrations of aluminium (average RSDs = 3.38% and 6.45%, and LODs = 0.5 ng (0.25 ppm) and 2 ng (0.5 ppm), for traditional and distance-based detection, respectively).

The deposition of chemical reagent inks on paper is a crucial step in the development and fabrication of microfluidic paper-based analytical devices (mu PADs). A pen-plotting approach, delivering chemical ink deposition using technical pens filled with reagents and inserted into a desktop electronic plotter, is shown herein to be a versatile, low-cost, simple, rapid, reproducible, and high-throughput solution. The volume of the deposited ink was quantified gravimetrically, confirming that nanoliter volumes of reagents can be deposited reproducibly (e.g. 7.55 +/- 0.37 nL/mm for a plotting speed of 10 cm/s) in detection zones of mu PADs, typically spatially defined using wax printing. This approach was further investigated with regard to deposition of reagents in different geometrical forms (circular and linear), so demonstrating its applicability for preparation of mu PADs with flexible design and application. By adjusting the plotting speed for linear deposition, lines with a relatively large range of widths (approximate to 628-1192 mm) were created. Circular deposition was also demonstrated via delivery of reagents within wax printed circular fluidic barriers of a range of diameters (inner diameter = 1.5-7 mm). These capabilities were practically demonstrated via the fabrication of mu PADs, based upon differing detection principles for determination of aluminum in natural waters using Morin as the fluorescent reagent. Traditional mu PADs based on digital image colorimetry (DIC) were produced using circular deposition, whilst distance-based mu PADs exploited linear deposition. Both types of mu PADs developed using this method showed excellent precision for determination of trace concentrations of aluminium (average RSDs = 3.38% and 6.45%, and LODs = 0.5 ng (0.25 ppm) and 2 ng (0.5 ppm), for traditional and distance-based detection, respectively).

Contact with thermal printing paper is a relevant source of dermal exposure to unbonded bisphenol A (BPA). In order to limit this exposure route, the European Union has introduced a drastic reduction in the maximum allowed concentration of BPA in thermal paper produced after beginning of year 2020. This study investigates the suitability of direct analysis in real time (DART), combined with accurate mass spectrometry, as a faster alternative to chromatography-based methods for the quantitative determination of BPA, and three analogues species, in receipts and tickets usually printed on thermal paper. The ionization efficiency of these compounds is evaluated under different conditions, and the effect of instrumental parameters of the DART source in the observed responses is discussed. The yield of the DART desorption-ionization process was greatly improved when compounds are previously converted into their acetyl derivatives; thereafter, the temperature of electronically excited helium atoms was the most relevant of the evaluated instrumental parameters. Under optimized conditions, the reported method provided recoveries in the range from 90 to 110 %, a limit of quantification of 0.004% (w:w), well below the maximum concentration established after 2020 for BPA (0.02%, w:w), and permitted to perform duplicate determinations of each sample extract with a response time around 1 min. The accuracy of BPA levels found in non-spiked samples was confirmed using GC-EI-MS as reference technique. BPA was systematically noticed in the processed samples with concentrations ranging from 0.005% to more than 6%.

Magnesium oxide nanoparticles (MgO NPs) have attracted considerable interest as antimicrobial agents in a wide variety of applications. We report a simple synthetic route towards MgO NPs (average diameter 10 nm) possessing potent antibacterial activity against both Gram-negative and Gram-positive bacteria. Detailed electron microscopy studies show how these particles induce oxidative stress, cell membrane leakage and cell death in bacteria at low NP concentrations, but remain non-toxic to eukaryotic cells. Applying a homogeneous dispersion of these nanoparticles on 18th century paper proved to be a highly effective means of preventing bacterial colonisation without altering the appearance of the paper samples, thus opening the doors to the use of these colourless, low-cost, and scalable nanoparticles for preventing biodeterioration in a range of paper-based objects and surfaces.

[Background and aim] The European Society of Clinical Microbiology and Infectious Diseases (ESCMID) aims to further develop its role in international medical and scientific guidance in the field of Clinical Microbiology and Infectious Diseases, where many types of guidance documents exist. The ESCMID Executive Committee and the Clinical Microbiology and Infection (CMI) editorial board wish to clarify the terminology and format to be used in ESCMID guidance documents submitted for publication in CMI, and to highlight the principles behind ESCMID guidance documents. [Types of guidance documents] There are five types of ESCMID guidance documents: White Papers, Clinical Practice Guidelines, Consensus Statements, State-of-the-Science Statements, and Position Papers. They differ in scope, methods of development, drafting group composition and preferred publication format. Guidance documents can be proposed, developed and published by ESCMID Study Groups, Committees and individual members; often, other scientific societies are involved. The full disclosure of potential conflicts of interest of all drafting group members is a requirement. [Final remarks] Guidance documents constitute a common cultural and scientific background to people in the same and related professions. Also, they are an important educational and training tool. Developing a guidance document is a scientific endeavour, where a sound and transparent development process is needed, requiring multidisciplinary and personal skills.

Currently, testing for immunoglobulin E (IgE) sensitization is the cornerstone of diagnostic evaluation in suspected allergic conditions. This review provides a thorough and updated critical appraisal of the most frequently used diagnostic tests, both in vivo and in vitro. It discusses skin tests, challenges, and serological and cellular in vitro tests, and provides an overview of indications, advantages and disadvantages of each in conditions such as respiratory, food, venom, drug, and occupational allergy. Skin prick testing remains the first line approach in most instances; the added value of serum specific IgE to whole allergen extracts or components, as well as the role of basophil activation tests, is evaluated. Unproven, non-validated, diagnostic tests are also discussed. Throughout the review, the reader must bear in mind the relevance of differentiating between sensitization and allergy; the latter entails not only allergic sensitization, but also clinically relevant symptoms triggered by the culprit allergen.

Question: Does tailored prescription of digitally enabled rehabilitation using affordable devices improve mobility and physical activity in people with mobility limitations admitted to aged care or neurological rehabilitation? Design: Pragmatic, parallel-group, randomised controlled trial with concealed allocation and blinded outcome assessment. Setting: Three inpatient rehabilitation (aged care, neurological rehabilitation) hospitals in Australia. Participants: Adults with reduced mobility (defined using Short Physical Performance Battery score < 12), clinician-assessed capacity for improvement, life expectancy > 12 months, anticipated length of stay at least 10 days from randomisation, and able to maintain standing position (assistance of one person permitted). Key exclusion criteria were cognitive or visual impairment likely to interfere with device use, inability to communicate in English, medical conditions prohibiting exercise and anticipated discharge to nursing home. Randomisation of 300 participants allocated 149 to usual care plus digitally enabled rehabilitation and 151 to usual care only. Interventions: Both groups received usual multidisciplinary rehabilitation care. In addition, the intervention group was prescribed 30 to 60 minutes of digitally enabled rehabilitation (virtual reality video games, activity monitors, tablet and smartphone exercise applications) 5 days a week in hospital and after discharge (using loaned devices) for 6 months. The digitally enabled rehabilitation was individually tailored and progressed by a physiotherapist. Outcome measures: Co-primary outcomes were mobility (performance-based Short Physical Performance Battery) and upright time as a proxy for physical activity (proportion of day upright measured by activPAL, averaged over 7 days) 6 months after randomisation. Secondary outcomes included performance- based and patient-reported measures of mobility and physical activity. Results: A total of 258 participants (129 control

The current health crisis caused by COVID-19 is a challenge for oncology treatment, especially when it comes to radiotherapy. Cancer patients are already known to be very fragile and COVID-19 brings about the risk of severe respiratory complications. In order to treat patients safely while protecting medical teams, the entire health care system must optimize the way it approaches prevention and treatment at a time when social distancing is key to stemming this pandemic. All indications and treatment modalities must be re-discussed. This is particularly the case for radiotherapy of bone metastases for which it is possible to reduce the number of sessions, the frequency of transport and the complexity of treatments. These changes will have to be discussed according to the organization of each radiotherapy department and the health situation, while medical teams must remain vigilant about the risks of complications of bone metastases, particularly spinal metastases. In this short piece, the members of the GEMO (the European Study Group of Bone Metastases) offer a number of recommendations to achieve the above objectives, both in general and in relation to five of the most common situations on radiation therapy for bone metastases.