Search

We present a method to estimate high frequency rotary motion of a highly compact electrostatic micro-scanner using the same electrodes for both actuation and sensing. The accuracy of estimated rotary motion is critical for reducing blur and distortion in image reconstruction applications with the micro-scanner given its changing dynamics due to perturbations such as temperature. To overcome the limitation that no dedicated sensing electrodes are available in the proposed applications due to size constraints, the method adopts electromechanical amplitude modulation (EAM) to separate motion signal from parasitic capacitance feedthrough, and a novel non-linear measurement model is derived to characterize the relationship between large out-of-plane angular motion and circuit output. To estimate motion, an extended Kalman filter (EKF) and an unscented Kalman filter (UKF) are implemented, incorporating a process model based on the micro-scanner's parametric resonant dynamics and the measurement model. Experimental results show that compared to estimation without using the measurement model, our method is able to improve the rotary motion estimation accuracy of the micro-scanner significantly, with a reduction of root-mean-square error (RMSE) in phase shift of 86.1%, and a reduction of RMSE in angular position error of 78.5 %.

Nanostructured Indium(III) oxide (In₂O₃) films deposited by low temperature pulsed electron deposition (LPED) technique on customized alumina printed circuit boards have been manufactured and characterized as gas sensing devices. Their electrical properties have monitored directly during deposition to optimize their sensing performance. Experimental results with oxidizing (NO₂) as well as reducing (CO) gases in both air and inert gas carriers are discussed and modeled.

Geometric correction is fundamental in producing high quality satellite data products. However, the geometric correction for ocean color sensors, e.g., Geostationary Ocean Color Imager (GOCI), is challenging because the traditional method based on ground control points (GCPs) cannot be applied when the shoreline is absent. In this study, we develop a hybrid geometric correction method, which applies shoreline matching and frequency matching on slots with shorelines and without shorelines, respectively. Frequency matching has been proposed to estimate the relative orientation between GOCI slots without a shoreline. In this paper, we extend our earlier research for absolute orientation and geometric correction by combining frequency matching results with shoreline matching ones. The proposed method consists of four parts: Initial sensor modeling of slots without shorelines, precise sensor modeling through shoreline matching, relative orientation modeling by frequency matching, and generation of geometric correction results using a combination of the two matching procedures. Initial sensor modeling uses the sensor model equation for GOCI and metadata in order to remove geometric distortion due to the Earth's rotation and curvature in the slots without shorelines. Precise sensor modeling is performed with shoreline matching and random sample consensus (RANSAC) in the slots with shorelines. Frequency matching computes position shifts for slots without shorelines with respect to the precisely corrected slots with shorelines. GOCI Level 1B scenes are generated by combining the results from shoreline matching and frequency matching. We analyzed the accuracy of shoreline matching alone against that of the combination of shoreline matching and frequency matching. Both methods yielded a similar accuracy of 1.2 km, which supports the idea that frequency matching can replace traditional shoreline matching for slots without visible shorelines.

In-depth analysis and performance evaluation of sensor fusion-based estimators may be critical when performed using real-world sensor data. For this reason, simulation is widely recognized as one of the most powerful tools for algorithm benchmarking. In this paper, we present a simulation framework suitable for assessing the performance of sensor fusion-based pose estimators. The systems used for implementing the framework were magnetic/inertial measurement units (MIMUs) and a camera, although the addition of further sensing modalities is straightforward. Typical nuisance factors were also included for each sensor. The proposed simulation environment was validated using real-life sensor data employed for motion tracking. The higher mismatch between real and simulated sensors was about 5% of the measured quantity (for the camera simulation), whereas a lower correlation was found for an axis of the gyroscope (0.90). In addition, a real benchmarking example of an extended Kalman filter for pose estimation from MIMU and camera data is presented.

Inductive Loop Detectors (ILDs) are the most commonly used sensors in traffic management systems. This paper shows that some spectral features extracted from the Fourier Transform (FT) of inductive signatures do not depend on the vehicle speed. Such a property is used to propose a novel method for vehicle classification based on only one signature acquired from a sensor single-loop, in contrast to standard methods using two sensor loops. Our proposal will be evaluated by means of real inductive signatures captured with our hardware prototype.

Signal strength-based positioning in wireless sensor networks is a key technology for seamless, ubiquitous localization, especially in areas where Global Navigation Satellite System (GNSS) signals propagate poorly. To enable wireless local area network (WLAN) location fingerprinting in larger areas while maintaining accuracy, methods to reduce the effort of radio map creation must be consolidated and automatized. Gaussian process regression has been applied to overcome this issue, also with auspicious results, but the fit of the model was never thoroughly assessed. Instead, most studies trained a readily available model, relying on the zero mean and squared exponential covariance function, without further scrutinization. This paper studies the Gaussian process regression model selection for WLAN fingerprinting in indoor and outdoor environments. We train several models for indoor/outdoor- and combined areas; we evaluate them quantitatively and compare them by means of adequate model measures, hence assessing the fit of these models directly. To illuminate the quality of the model fit, the residuals of the proposed model are investigated, as well. Comparative experiments on the positioning performance verify and conclude the model selection. In this way, we show that the standard model is not the most appropriate, discuss alternatives and present our best candidate.

The Ocean Bottom Seismometer (OBS) is a key instrument for the geophysical study of sea sub-bottom layers. At present, more reliable autonomous instruments capable of recording underwater for long periods of time and therefore handling large data storage are needed. This paper presents a new Ocean Bottom Seismometer designed to be used in long duration seismic surveys. Power consumption and noise level of the acquisition system are the key points to optimize the autonomy and the data quality. To achieve our goals, a new low power data logger with high resolution and Signal-to-Noise Ratio (SNR) based on Compact Flash memory card is designed to enable continuous data acquisition. The equipment represents the achievement of joint work from different scientific and technological disciplines as electronics, mechanics, acoustics, communications, information technology, marine geophysics, etc. This easy to handle and sophisticated equipment allows the recording of useful controlled source and passive seismic data, as well as other time varying data, with multiple applications in marine environment research. We have been working on a series of prototypes for ten years to improve many of the aspects that make the equipment easy to handle and useful to work in deep-water areas. Ocean Bottom Seismometers (OBS) have received growing attention from the geoscience community during the last forty years. OBS sensors recording motion of the ocean floor hold key information in order to study offshore seismicity and to explore the Earth's crust. In a seismic survey, a series of OBSs are placed on the seabed of the area under study, where they record either natural seismic activity or acoustic signals generated by compressed air-guns on the ocean surface. The resulting data sets are subsequently used to model both the earthquake locations and the crustal structure.