Search

The present work investigates the mechanical properties of a composite material composed of multi-walled carbon nanotubes (MWCNTs), nano-aluminum powder (NAP), and glass fibers (GF) for five different compositions. The study further investigated how MWCNTs contribute to maintaining the mechanical properties of nanocomposites when exposed to elevated temperatures, up to 180 °C. The evaluation of impact strength revealed that the nanocomposite, composed of 2 % MWCNTs, 15 % NAP, and 10 % GF, demonstrated the greatest impact strength. At room temperature, the composite containing 2 % MWCNTs, 5 % NAP, and 20 % GF exhibited the highest ultimate tensile strength (UTS). Conversely, at elevated temperatures reaching up to 180 °C, the highest UTS was observed in the composition with 2 % MWCNTs, 10 % NAP, and 15 % GF. The hardness of the nanocomposite was influenced by its composition; at room temperature, the maximum hardness was observed in the mixture containing 2 % MWCNTs, 20 % NAP, and 5 % GF. In contrast, at elevated temperatures, the composition with 2 % MWCNTs, 5 % NAP, and 20 % GF exhibited the highest hardness. Overall, the study found that incorporating GF and NAP improved the mechanical properties of the composite. These results indicate that the composite's performance could be further optimized for specific applications through the addition of filler materials., Competing Interests: The authors declare the following financial interests/personal relationships which may be considered as potential competing interests., (© 2024 The Authors.)

Short glass fibers are generally used in posterior dental restorations to enhance the mechanical properties and improve the material microstructure. Two resin-based composites (S0 and SF) were formulated and characterized to investigate the influence of zirconium in their characteristics and properties. The organic part of the investigated materials was the same (BisGMA, TEGDMA, and a photochemical polymerization system), and in the inorganic part, besides quart, glassA, and hydroxylapatite with Zn, sample S0 contained strontium glass with zirconium and sample SF contained fiber powder of chopped zirconium. The samples were characterized by the degree of conversion (DC), mechanical properties, water sorption (WS), scanning electron microscopy (SEM), atomic force microscopy (AFM) before and after the WS test, and antimicrobial properties. The results obtained were subjected to one-way ANOVA and Tukey's statistical tests. Both samples had a high DC. Regarding the mechanical properties, both samples were very similar, except DTS, which was higher for the composite without fibers. After 14 days, the WS value of the SF sample was lower than that of the S0 sample. Water caused significant changes in the topography of the SF sample, but thanks to its antimicrobial properties and the diffusion phenomenon, SF had a more pronounced antimicrobial effect. This study shows that the addition of appropriate amounts of Sr-Zr-glass powder gives the material in which it is added similar properties to material containing chopped zirconium glass fiber powder. According to the antimicrobial test results, resin composites containing experimental zirconia fillings can be considered in future in vitro clinical studies for posterior reconstructions with significantly improved mechanical properties.

This study experimentally investigates the influence of metal chips and glass fibers on the mode I fracture toughness, energy absorption, and tensile strength of polymer concretes (PCs) manufactured by waste aggregates. A substantial portion of the materials employed in manufacturing and enhancing the tested polymer concrete are sourced from waste material. To achieve this, semi-circular bend (SCB) samples were fabricated, both with and without a central crack, to analyze the strength and fracture behavior of the composite specimens. The specimens incorporated varying weight percentages comprising 50 wt% coarse mineral aggregate, 25 wt% fine mineral aggregate, and 25 wt% epoxy resin. Metal chips and glass fibers were introduced at 2, 4, and 8 wt% of the PC material to enhance its mechanical response. Subsequently, the specimens underwent 3-point bending tests to obtain tensile strength, mode I fracture toughness, and energy absorption up to failure. The findings revealed that adding 4% brass chips along with 4% glass fibers significantly enhanced energy absorption (by a factor of 3.8). However, using 4% glass fibers alone improved it even more (by a factor of 10.5). According to the results, glass fibers have a greater impact than brass chips. Introducing 8% glass fibers enhanced the fracture energy by 92%. However, in unfilled samples, aggregate fracture and separation hindered crack propagation, and filled samples presented added barriers, resulting in multiple-site cracking.

Glass fibers (GFs) are commonly used as reinforcements for advanced polymer composites. To improve the interfacial shear properties and mechanical properties of GF-reinforced composites (GFRPs), carbon nanotubes (CNTs) are directly grafted onto GFs using chemical vapor deposition (CVD). However, this process requires high temperatures, which causes thermal degradation of GFs, deteriorating their mechanical properties. In this study, a low-temperature CNT-grafting process was investigated using a bimetallic catalyst introduced onto a GF fiber surface via precursor solutions. The mechanical properties of the CNT-grafted GFs fabricated at different CVD temperatures were evaluated; they consistently showed low tensile strengths at temperatures above 400 °C. Subsequently, various CNT-grafted GFRPs were manufactured, and their mechanical properties were characterized. Interestingly, the flexural strengths of the composites increased with maintained tensile strength, despite a deterioration of the CNT-grafted GF reinforcements due to the CVD process. This could be attributed to the improved interfacial shear strength (IFSS) of the CNT-grafted GFs at the fiber level, and the enhanced compressive strength and interlaminar shear strength (ILSS) of CNT-grafted GFRPs at the composite level. Considering the properties of GF through CVD processes, particularly in relation to temperature, and factors such as IFSS, ILSS, tensile, compressive and flexural properties of composite materials, grafting CNTs on GF via a CVD system demonstrated its highest optimality at 450 °C., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 The Authors. Published by Elsevier Ltd.)

"Interleaving" is widely used for interlaminar toughening of fiber-reinforced composites, and the structure of interleaving is one of the important factors affecting the toughening efficiency of laminates. Several experiments have demonstrated that compared to continuous and dense structures, toughening layers with structural heterogeneity can trigger multiple toughening mechanisms and have better toughening effects. On this basis, this work further investigates the application of heterogeneous toughening phases in interlaminar toughening of bidirectional GFRP. CNT was selected to construct toughening phases, which was introduced into the interlaminar of composites through efficient spraying methods. By controlling the amount of CNT, various structures of CNT toughening layers were obtained. The fracture toughness of modified laminates was tested, and their toughening mechanism was analyzed based on fracture surface observation. The results indicate that the optimal CNT usage (0.5 gsm) can increase the initial and extended values of interlayer fracture toughness by 136.0% and 82.0%, respectively. The solvent acetone sprayed with CNT can dissolve and re-precipitate a portion of the sizing agent on the surface of the fibers, which improves the bonding of the fibers to the resin. More importantly, larger discrete particles are formed between the layers, guiding the cracks to deflect in the orientation of the toughened layer. This generates additional energy dissipation and ultimately presents an optimal toughening effect.

Degradation of polymer composites is a significant problem in many engineering aspects. Due to the interaction of various degradation factors during the exploitation of composites, a synergistic effect of destruction is observed. The article describes the phenomena occurring in glass fiber reinforced polyester laminates under the influence of ultraviolet radiation (UV) in an aquatic environment. The laminates were exposed to UV-A, UV-B and UV-C radiation for 1000 h in free-air and underwater conditions. During the test, the materials were immersed at stable depth of 1 mm and 10 mm, respectively. The three-point bending tests performed on the samples after being exposed to UV showed an increase in the flexural strength of the composites. Simultaneously, degradation of the outer surface layer was observed. The degradation removed the thin resin film from the surface which resulted in a direct exposure of the reinforcing fibers to the environment. The transformations taking place in the deeper layers of the composite increased the mechanical strength due to the additional cross-linking reactions excited by the energy arising from the radiation. Moreover, the formation of polymer structures from free styrene remaining after the technological process and the occurrence of free radical reactions as a result of the cage effect was also observed., (© 2024. The Author(s).)

The chemical structure of the surface of glass fibers, including silanized fibers, was studied. Highly efficient heat-resistant composites were obtained by impregnating silanized glass fiber with a polysulfone solution, and the effect of modification of the surface of glass fibers on the physical, mechanical and thermophysical properties of the composite materials was studied. As a result of the study, it was found that the fiber-to-polymer ratio of 70/30 wt.% showed the best mechanical properties for composites reinforced with pre-heat-treated and silanized glass fibers. It has been established that the chemical treatment of the glass fibers with silanes makes it possible to increase the mechanical properties by 1.5 times compared to composites reinforced with initial fibers. It was found that the use of silane coupling agents made it possible to increase the thermal stability of the composites. Mechanisms that improve the interfacial interaction between the glass fibers and the polymer matrix have been identified. It has been shown that an increase in adhesion occurs both due to the uniform distribution of the polymer on the surface of the glass fibers and due to the improved wettability of the fibers by the polymer. An interpenetrating network was formed in the interfacial region, providing a chemical bond between the functional groups on the surface of the glass fiber and the polymer matrix, which was formed as a result of treating the glass fiber surface with silanes, It has been shown that when treated with aminopropyltriethoxysilane, significant functional unprotonated amino groups NH + /NH 2 + are formed on the surface of the fibers; such free amino groups, oriented in the direction from the fiber surface, form strong bonds with the matrix polymer. Based on experimental data, the chemical structure of the polymer/glass fiber interface was identified.

Electronic waste (e-waste) is one of the fastest-growing waste streams in the world and Europe is classified as the first producer in terms of per capita amount. To reduce the environmental impact of e-waste, it is important to recycle it. This work shows the possibility of reusing glassy substrates, derived from the MW-assisted acidic leaching of Waste Printed Circuit Boards (WPCBs), as an adsorbent material. The results revealed an excellent adsorption capability against methylene blue (MB; aqueous solutions in the concentration range 10 -5 M-2 × 10 -5 M, at pH = 7.5). Comparisons were performed with reference samples such as activated carbons (ACs), the adsorbent mostly used at the industrial level; untreated PCB samples; and ground glass slides. The obtained results show that MW-treated WPCB powder outperformed both ground glass and ground untreated PCBs in MB adsorption, almost matching AC adsorption. The use of this new adsorbent obtained through the valorization of e-waste offers advantages not only in terms of cost but also in terms of environmental sustainability.

Composite resin is universally used for posterior teeth restorations. Fibers have been suggested for the mechanical improvement of the restorations. This study assessed the fracture resistance of class II fiber-reinforced composite restorations and compared it with the fracture resistance of three control groups: (1) healthy teeth, (2) non-fiber-reinforced restorations and (3) unrestored cavities. A search was performed using PubMed, Web of Science and Google Scholar from 15 May to 12 June 2023. Only in vitro studies from the last 10 years were included for this systematic analysis. This study was registered in the PROSPERO database, it followed PRISMA guidelines and the risk of bias was assessed using the QUIN tool. Fracture resistance median values, in Newtons (N), were calculated for the experimental and control groups (95% confidence interval). For pairwise comparison, nonparametric tests ( p < 0.05) were applied. Twenty-four in vitro studies met the inclusion criteria. The fracture resistance of the experimental group was 976.0 N and differed ( p < 0.05) from all controls. The experimental group showed lower values of fracture resistance than healthy teeth (1459.9 N; p = 0.048) but higher values than non-fiber-reinforced restorations (771.0 N; p = 0.008) and unrestored cavities (386.6 N; p < 0.001). In vitro systematic outcomes evidenced that glass and/or polyethylene fibers improved the fracture resistance of composite restorations.

Objective: to investigate and compare the reinforcing effects of glass fibers (GFs) and ZrO 2 nanoparticles at different ratios on the Flexural Strength (FS), Microhardness (MH), and Surface Roughness (SR) of autopolymerizing provisional PMMA., Methods: A total of one hundred and twenty specimens of autopolymerizing PMMA were prepared for FS, MH, and SR tests and grouped as follows: no additives (control group), for the tested groups, different ratios of GFs and ZrO 2 at 5% of autopolymerizing PMMA were incorporated. The ratios of GFs/ZrO 2 nanoparticles were 0%-5%, 1%-4%, 2%-3%, 2.5%-2.5%, 3%-2%, 4%-1% and 5%-0% (n = 5). The FS was evaluated using the three-point bending test, MH was evaluated using the Vickers microhardness tester and SR was evaluated using a contact-type profilometer. Data were analyzed using ANOVA, Tukey's test, and Person correlation at 0.05 level of significance ., Results: The unreinforced group had the lowest FS, MH, and SR mean values followed by (0%GFs + 5% ZrO 2 ), (1% GFs + 4% ZrO 2 ), (2% GFs + 3% ZrO 2 ), (2.5% GFs + 2.5% ZrO 2 ), (3% GFs + 2% ZrO 2 ), (4% GFs + 1% ZrO 2 ) and (5% GFs + 0% ZrO 2 ) which had the highest values., Conclusion: Hybrid reinforcement with GFs, ZrO 2 nanoparticles, or a combination of them effectively improved flexural strength and microhardness of autopolymerizing provisional PMMA that would create provisional restorations with extended clinical service. GFs demonstrated superior reinforcing effects compared to ZrO 2 nanoparticles. However, reinforcement with 2.5-5% GFs increased the surface roughness for provisional restoration., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2023 The Authors.)

Under high temperatures, fiber-reinforced polymers are destroyed, releasing heat, smoke, and harmful volatile substances. Therefore, composite structural elements must have sufficient fire resistance to meet the requirements established by building codes and regulations. Fire resistance of composite materials can be improved by using mineral fillers as flame-retardant additives in resin compositions. This article analyzes the effect of fire-retardant additives on mechanical properties and fire behavior of pultruded composite profiles. Five resin mixtures based on vinyl ester epoxy and on brominated vinyl ester epoxy modified with alumina trihydrate and triphenyl phosphate were prepared for pultrusion of strip profiles of 150 mm × 3.5 mm. A series of tests have been conducted to determine mechanical properties (tensile, flexural, compression, and interlaminar shear) and fire behavior (ignitability, flammability, combustibility, toxicity, smoke generation, and flame spread) of composites. It was found that additives impair mechanical properties of materials, as they the take place of reinforcing fibers and reduce the volume fraction of reinforcing fibers. Profiles based on non-brominated vinyl ester epoxy have higher tensile, compressive, and flexural properties than those based on brominated vinyl ester epoxy by 7%, 30%, and 36%, respectively. Profiles based on non-brominated epoxy resin emit less smoke compared to those based on brominated epoxy resin. Brominated epoxy-based profiles have a flue gas temperature which is seven times lower compared to those based on the non-brominated epoxy. Mineral fillers retard the spread of flame over the composite material surface by as much as 4 times and reduce smoke generation by 30%.

Glass fibers are widely used in cement-based precast products, given the reinforcing requirements for toughness and strength. However, inferior alkali resistance hinders the effectiveness of glass fibers in reinforcing cement-based materials. In this paper, nanoparticle coatings were applied on the surface of alkali-resistant glass fiber (ARGF) as a protective layer via the in situ chemical reaction of oleic acid (OA) and potassium permanganate (PP). The morphology and constituents of the as-prepared ARGFs were examined using scanning electron microscopy (SEM) and obtaining X-ray photoelectron spectroscopy (XPS) measurements. Mass loss and strength retention were investigated to characterize alkali resistance of modified ARGFs. Results showed that ARGFs could be optimally coated by a layer of MnO 2 -based nanoparticles consisting of approximately 70% MnO 2 , 18% MnO, and 12% MnSiO 3 , when modified with an optimum OA to PP ratio of 10 for 24 h. The dissolution of ARGFs matrix in 4% and 10% NaOH solutions were distinctly delayed to 28 d, as a consequence of the introduction of the MnO 2 -based nanoparticle layer, compared with nontreated ARGF occurring at 3 d in 4% NaOH solution. For the optimally modified ARGFs, the mass loss was controlled to 1.76% and 2.91% after 90 d of corrosion in 4% and 10% NaOH solutions, and the retention of tensile strength was increased by approximately 25%. With respect to the increment in alkali-resistant performance, the modified ARGFs can be promising candidates for wide applications in alkaline cement-based products.

This study aims to analyze strength properties and low-cycle dynamic tests of composite materials modified with glass and basalt fibers. Biopolyamide 4.10 was used as the matrix, and the fiber contents were 15, 30, and 50% by weight. Static tensile tests, impact tests, and determination of mechanical hysteresis loops were carried out as strength tests. The length of the fibers in the produced composites and their processing properties were determined. The composite materials were compared with commercially available glass fiber-reinforced composites with 30 and 50% fiber contents. The results showed that such composites can successfully replace composite materials based on petroleum-based polymeric materials, providing high strength properties and reducing the negative environmental impact by using renewable sources. Composites with 30% basalt fiber composition were characterized by higher tensile strength by about 60% compared to commercially available composites with 30% glass fiber composition and an almost doubly increased Young's modulus. Increasing the content of basalt fibers to 50% results in a further increase in strength properties. Despite the lower tensile strength compared to polyamide 6 with 50% glass fiber content, basalt fibers provided an approximately 10% higher modulus of elasticity.

Unsized single-end rovings are oxygen plasma pretreated and organosilicon plasma coated using plasma nanotechnology to optimize the interphase in glass-fiber-reinforced polyester composites and to determine the achievable range of their shear strength for potential applications. This surface modification of the fibers allows us to vary the shear strength of the composite in the range of 23.1 to 45.2 MPa at reduced financial costs of the process, while the commercial sizing corresponds to 39.2 MPa. The shear strength variability is controlled by the adhesion of the interlayer (plasma nanocoating) due to the variable density of chemical bonds at the interlayer/glass interface. The optimized technological conditions can be used for continuous surface modification of rovings in commercial online fiber-processing systems.

Polymethylmethacrylate (PMMA) has been the most-widely used denture base material in prosthetic dentistry for the last 80 years. It is still one of the best alternatives when new methods are inapplicable. Due to the lack of some physical inadequacies occurring during cyclic use and accidental situations, various reinforcement strategies such as using nanoparticles, wires, fibers, and meshes have been investigated and reported. In this study, it was aimed to conduct a comparative investigation of the effect of fiber additives with different characteristics on the flexural properties of heat-cured PMMA denture base resins. Glass fibers (GFs), polypropylene fibers (PPFs), and carbon fibers (CFs) having 3, 6, and 12 mm lengths and 0.25, 0.50, and 1.0% concentrations ( v / v ) were used for the reinforcement of PMMA denture base resins. The flexural properties (flexural strength, flexural modulus, and maximum deformation) were determined using a three-point bending test, and three-way ANOVA analyses with Bonferroni corrections were performed on the test results. The morphologies of the fracture surfaces were analyzed using scanning electron microscopy. All three fibers exhibited reinforcement in the flexural strength ( p < 0.001) and flexural modulus ( p < 0.001) regardless of their length and concentration. The group with 1.0% 12 mm CF-reinforced PMMA exhibited the greatest flexural strength (94.8 ± 8.8 MPa), and that with 1.0% 3 mm GFs displayed the lowest flexural strength (66.9 ± 10.4 MPa) among the fiber-reinforced groups. The greatest value of the flexural modulus was displayed by the 1.0% 3 mm CF-reinforced resin (3288.3 ± 402.1 MPa). Although the CF-reinforced groups exhibited better flexural properties, CFs are not favorable for use as reinforcement in practice due to the dark gray discoloration of the denture base resin. It was concluded that PPF is a promising material for the reinforcement of heat-cured PMMA denture base resins.

With the development of the automotive industry, a large amount of waste rubber is produced every year. The application and development of recycled rubber concrete (RRC) can effectively reduce 'black pollution' caused by waste rubber. However, the addition of recycled rubber particles can lead to a decrease in the compressive behavior of concrete. Previous research has demonstrated that by preventing crack growth, fiber addition can increase the strength and ductility of concrete. In this work, a total of 28 RRC mixes are designed, and the compressive behavior of RRC reinforced by steel fibers (SFs) and glass fibers (GFs) is investigated. The workability of fresh RRC can be negatively impacted by an increase in both fiber contents, with the GF content having a more notable effect. With the addition of fibers, the maximum increase rates for the compressive strength, elastic modulus, strain at peak stress, and compressive toughness were 27%, 8%, 45%, and 152%, respectively. A constitutive model is concurrently put forward to forecast the stress-strain curves of RRC with various fiber contents. These findings indicate that the maximum improvement in compressive behavior is achieved when the GF content was 0.4% and the SF content was 1.2%. The proposed constitutive model can be used to predict the stress-strain curve of hybrid fiber-reinforced recycled rubber concrete (HFRRRC).

Composite materials with carbon and glass fibers in an epoxy matrix are widely used systems due to their excellent mechanical parameters, and machining is a standard finishing operation in their manufacture. Previous studies focused exclusively on the characteristics of the fibers released into the air. This work aimed to analyze the nature of the material waste that remains on the work surface after machining. The dust on the work surface is made up of fibers and a polymer matrix, and due to its dimensions and chemical stability, it is a potentially dangerous inhalable material currently treated as regular waste. The smallest sizes of destroyed carbon fibers were generated during drilling and grinding (0.1 μm), and the smallest glass fiber particles were generated during milling (0.05 μm). Due to their nature, carbon fibers break by a tough fracture, and glass fibers by a brittle fracture. In both cases, the rupture of the fibers was perpendicular to or at an angle to the longitudinal axis of the fibers. The average lengths of destroyed carbon fibers from the tested processes ranged from 15 to 20 µm and 30 to 60 µm for glass fibers.

This experimental study investigated how defects, in particular fiber misalignment, affect the mechanical behavior of glass fiber composites (GFRP) under compressive loading. GFRP cross-plies with three different types of fiber misalignment, namely a fold, a wave, and an in-plane undulation, were fabricated using the resin transfer molding process. The compressive tests were performed at four different temperatures, in order to investigate the role of a change in the matrix properties on the strength of the composite. The experiments showed that the defects, especially at lower temperatures, had a significant impact on the mechanical properties of the composite, exceeding the proportion of the defects inside the composite. With increasing temperature, the damage mechanism changed from fiber-dominated to matrix-dominated and, in doing so, decreased the significance of fiber misalignment for the mechanical behavior.

Current collectors are indispensable parts that provide electron transport and mechanical support of electrode materials in a battery. Nowadays, thin metal foils made of Cu and Al are used as current collectors of lithium batteries, but they do not contribute to the storage capacity. Therefore, decreasing the weight of current collectors can directly enhance the energy density of a battery. However, limited by the requirements of mechanical strength, it is difficult to reduce the weight of metal foils any further. Herein, a new type of current collectors made of 3D metallic glass-fiber fabrics (MGFs), which shows advantages of super-lightweight (2.9-3.2 mg cm⁻ 2 ), outstanding electrochemical stability for cathodes and anodes of lithium-ion and lithium-metal batteries (LMBs), fire resistance, high strength, and flexibility suitable for roll-to-roll electrode fabrication is reported. The gravimetric energy densities of lithium batteries exhibit improvements of 9-18% by only replacing the metal foils with the MGFs. In addition, MGFs are suitable for the fabrication of flexible batteries. A high-energy-density flexible lithium battery with an outstanding figure of merit of flexible battery (fb FOM ) and flexing stability is demonstrated., (© 2023 Wiley-VCH GmbH.)

Aim: To compare the load-bearing capacity of three and four-unit fixed partial denture (FPD) with two different designs of pontics reinforced with industrial glass fibers at two different positions of the FPD., Materials and Methods: A total of 64 samples were made with Bis-acryl composite temporary material and reinforced with industrial glass fibers (E-glass). The specimens were divided into eight groups (groups I-VIII) depending on the number of units, type of pontic design and area of placement of fibers. A universal testing machine was used to evaluate and compare the load-bearing capacity of the specimens. The evaluated data were statistically analyzed using one-way ANOVA and Bonferroni post hoc tests ( p ≤ 0.05)., Results: Three-unit interim FPD and modified ridge lap pontic design showed greater load-bearing capacity after reinforcement with glass fibers than a four-unit interim FPD and hygienic pontic design, respectively. Fiber placement at the occlusal plus connector area as well as the cervical plus connector area had comparable results., Conclusion: Industrial glass fibers (E-glass) could be used as a cheaper alternative but clinical performance and their safety are yet to be evaluated., Clinical Significance: Reinforcement with industrial-grade glass fibers can be a cheaper option for increasing the load-bearing capacity of interim partial dentures, but it needs to be studied in vivo through further studies.

Introduction: Most denture fractures occur within the mouth due to resin flexural fatigue. For example, the deep labial notch at the high labial frenum causes denture breakage, as can deep scratches and generated processing stresses. The rising cost of annual prosthetic repairs is evidence that the problem of total denture fracture has not been solved. The purpose of this investigation was to evaluate the relative improvement in flexural strength between heat-cured polymethyl methacrylate (PMMA) resin reinforced with glass fibers (GF) and basalt fibers (BF) of varied orientations., Material and Methods: A total of 150 heat-cured acrylic resin specimens of 65x10x3 mm dimension were prepared, 30 of which were left unreinforced (Group A), 30 of which were reinforced with GF in transverse pattern (Group B), 30 of which were reinforced with GF in meshwork pattern (Group C), 30 of which were reinforced with BF in transverse pattern (Group D), and 30 of which were reinforced with BF in meshwork pattern (Group E). All of the samples were put through flexural strength testing on the universal testing machine. One-way ANOVA and the Tukey-Kramer various correlation test (= 0.05) were used in SPSS for Windows to look at the facts., Results: The mean flexural strength for Group A was 46.26±2.26 MPa, 64.98±1.53 MPa for Group B, 76.45±2.67 MPa for Group C, 54.22±2.24 MPa for Group D, and 59.02±2.38 MPa for Group E. Flexural strength was impacted by both the kind of BF and GF reinforcement (F = 768.316, P = 0.001)., Conclusion: Within the limitation of the current research, BF reinforcement outperforms GF reinforcement and unreinforced heat-cured acrylic resin in terms of flexural strength., Competing Interests: The authors have declared that no competing interests exist., (Copyright © 2023, Nayak et al.)

The demand for energy storage is growing, and the disadvantages of lithium-ion batteries are being explored to overcome them. Accordingly, aqueous zinc-ion batteries (ZIBs) are developing very rapidly, owing to their high safety, environmental friendliness, high abundance of resources, and high cost performance. Over the last decade, ZIBs have made remarkable progress through extensive efforts in the field of electrode materials and through fundamental understanding of non-electrode components, such as solid-electrolyte interphase, electrolytes, separators, binders, and current collectors. In particular, the breakthrough in using separators on non-electrode elements should not be overlooked as such separators have proven key to conferring ZIBs with high energy and power density. In this Review, recent progress in the development of separators in ZIBs is comprehensively summarized based on their functions and roles in ZIBs, including the modification of conventional separators and the development of novel separators. Finally, the prospects and future challenges of separators are also discussed to facilitate ZIBs development., (© 2023 Wiley-VCH GmbH.)

Lunar glasses with different origins act as snapshots of their formation processes, providing a rich archive of the Moon's formation and evolution. Here, we reveal diverse glasses from Chang'E-5 (CE-5) lunar regolith, and clarify their physical origins of liquid quenching, vapor deposition and irradiation damage respectively. The series of quenched glasses, including rotation-featured particles, vesicular agglutinates and adhered melts, record multiple-scale impact events. Abundant micro-impact products, like micron- to nano-scale glass droplets or craters, highlight that the regolith is heavily reworked by frequent micrometeorite bombardment. Distinct from Apollo samples, the indigenous ultra-elongated glass fibers drawn from viscous melts and the widespread ultra-thin deposited amorphous rims without nanophase iron particles both indicate a relatively gentle impact environment at the CE-5 landing site. The clarification of multitype CE-5 glasses also provides a catalogue of diverse lunar glasses, meaning that more of the Moon's mysteries, recorded in glasses, could be deciphered in future., (© The Author(s) 2023. Published by Oxford University Press on behalf of China Science Publishing & Media Ltd.)

This study aimed to compare the effect of fiber reinforcing methods on the flexural strength and failure modes of indirect composite resins. Based on the reinforcement methods, the bar specimens (3 × 3 × 25 mm) were divided into five groups (n = 20). Glass or polyethylene fibers were used for reinforcement of indirect composite resins. Fibers were either light polymerized and mixed with indirect composite resin or mixed with indirect composite resin after resin application and polymerized together. Indirect composite resin without fiber reinforcement was used as control. All five types of specimens were stored in distilled water at 37°C for 24 h. Half of the specimens were additionally thermocycled. Then the specimens were tested in a three-point bending test. Failure types were examined and categorized by using stereo microscope. The data were analyzed using two-way ANOVA and Tukey HSD test. Flexural strength was found to be significantly higher for fiber-reinforced indirect resin composites than control. However, the fiber-reinforced groups did not present any significant difference. Analysis revealed aging does not affect the flexure strength of fiber reinforcement of indirect composite resin. The study concluded that the flexure strength of indirect composite resins was improved with fiber reinforcement. Different fiber reinforcement methods demonstrated similar effects on the flexure strength of indirect composite resin. Reinforcement with glass or polyethylene fibers presented the potential to improve the mechanical properties of indirect composite resins. RESEARCH HIGHLIGHTS: Flexural strength of indirect composite resins are affected by the reinforcement of composites with glass or polyethylene fibers. Aging with thermocycling has no effect on the flexural strength of the indirect composite resins, however can cause catastrophic failures in material., (© 2022 Wiley Periodicals LLC.)

Silanized glass fibers are popular reinforcements of acrylic denture base materials. To increase the number of surface hydroxyl groups and to improve interfacial adhesion between the matrix and reinforcements, acid or base treatments of glass fibers are commonly performed before the silanization. However, limited data are available on the effect of these treatments on the mechanical properties of acrylic matrix composite materials used for denture base applications. In this work, before the silanization of a woven glass fiber fabric (GF) with 3-(trimethoxysilyl) propyl methacrylate, activation pretreatments using HCl and NH 4 OH aqueous solutions have been performed. To characterize the glass surface, FTIR spectroscopy was used. Specimens of cured acrylic denture base resin and composites were divided into five groups: (1) cured acrylic denture base resin-control group; (2) composite with non-silanized GF; (3) composite with silanized GF; (4) composite with NH 4 OH activated and silanized GF; (5) composite with HCl activated and silanized GF. The flexural and impact properties of specimens were evaluated by means of three-point-bending tests and Charpy impact testing, respectively. The residual reactivity of the samples was analyzed using differential scanning calorimetry. The results of mechanical testing showed that acid and base pretreatments of the glass fabric had a positive effect on the flexural modulus of prepared composites but a negative effect on their impact strength. Possible interfacial adhesion mechanisms and the diffusion control of isothermal cure reactions due to vitrification have been discussed.

This work sheds light on the first steps towards using glass fiber waste for semi-structural applications. This work aims to improve the properties of random flax fiber composites by incorporating waste glass fibers (WGF) obtained from the fiber production line. The waste glass fibers were incorporated as a core structure between the flax layers to form a hybrid composite. Two routes of manufacturing viz. vacuum infusion and autoclave were used to identify the optimum route to incorporate the WGF in flax fiber composites. The quality of composites was investigated in terms of residual void content and thickness uniformity. Residual void content was identified to be directly proportional to the WGF content in the composites. With the increase in WGF content, the flexural and impact properties were increased by 47% and 117%, respectively, indicating a positive hybridization effect. Furthermore, a global warming potential indicator was identified to be small, indicating the eco-friendliness of these composites.

The growing demand for polymer composites and their widespread use is inevitably accompanied by the need to know their degradation behavior over a sufficiently long period of time. This study focuses on commercial glass fiber rovings, which were stored in the indoor environment for up to 11 years. Fibers with different storage times, from fresh up to the oldest, were used to produce unidirectional fiber-reinforced polyester composites that were characterized to determine their shear and flexural properties dependent on fiber storage time. A significant decrease in shear strength was observed throughout the aging of the fibers, down to a decrease of 33% for the oldest fibers. An important finding, however, was that the significant decrease in shear strength was only partially reflected in the flexural strength, which corresponded to a decrease of 18% for the oldest fibers at consistent flexural modulus.

The aim of this study is to investigate the influence of different glass fibers made of commercial silicate, borosilicate, and laboratory-made iron-phosphate compositions, on the preparation of polylactic acid (PLA) composites and their structural and physical properties. The thermal, structural, and electrical properties of prepared PLA-glass fiber composites were studied using differential scanning calorimetry, X-ray diffraction, microscopy, and impedance spectroscopy. The structural as well as morphological, thermal, and electrical properties of all PLA-glass composites were found to be very similar and independent of the composition and aspect ratio of glass fibers. All types of glass fibers improve mechanical properties, increase thermal stability, and decrease the electrical conductivity of PLA, thereby producing mechanical strong electrically insulating composite material with potential in various applications.

An ever-growing amount of composite waste will be generated in the upcoming years. New circular strategies based on 3D printing technologies are emerging as potential solutions although 3D-printed products made of recycled composites may require post-processing. Metallization represents a viable way to foster their exploitation for new applications. This paper shows the use of physical vapor deposition sputtering for the metallization of recycled glass fiber-reinforced polymers processed by UV-assisted 3D printing. Different batches of 3D-printed samples were produced, post-processed, and coated with a chromium metallization layer to compare the results before and after the metallization process and to evaluate the quality of the finishing from a qualitative and quantitative point of view. The analysis was conducted by measuring the surface gloss and roughness, analyzing the coating morphology and thickness through the Scanning Electron Microscopy (SEM) micrographs of the cross-sections, and assessing its adhesion with cross-cut tests. The metallization was successfully performed on the different 3D-printed samples, achieving a good homogeneity of the coating surface. Despite the influence of the staircase effect, these results may foster the investigation of new fields of application, as well as the use of different polymer-based composites from end-of-life products, i.e., carbon fiber-reinforced polymers.

Context: Endodontically treated premolars are currently restored with direct bonded techniques in conservative manner enabling them to bear functional stresses homogeneously., Aim: The study aimed to evaluate the effect of placement of compactable glass fibers in reinforcing the endodontically treated teeth in a novel conservative manner., Settings and Design: Research laboratory, in vitro study., Materials and Methods: Seventy-five extracted maxillary premolars were procured. Fifteen teeth were left untreated (Group A) and the remaining teeth were endodontically treated followed by standardized mesio-occluso-distal preparation and randomly assigned to experimental groups ( n = 15) as follows: (B) no restoration, (C) restoration with composite, (D) EverStick ® POST followed by composite, and (E) vertical glass fibers within 3 mm of the coronal root canal space and buccopalatal flaring of the coronal fibers followed by composite. After conditioning and thermocycling, specimens were loaded under a universal testing machine to evaluate fracture resistance and fracture pattern of specimens., Statistical Analysis Used: Obtained scores were statistically analyzed using one-way analysis of variance test for stress analysis, post hoc Tukey's test for intergroup comparison, and Chi-square test for analysis of favorable and unfavorable fracture., Results: The fracture resistance was highest to lowest as follows: Group A > E > C > D > B ( P < 0.001)., Conclusion: EverStick ® POST used in conservative manner improved fracture strength of teeth significantly., Competing Interests: There are no conflicts of interest., (Copyright: © 2022 Journal of Conservative Dentistry.)

Based on the wave absorption model of 3D woven fabric and the zero-reflection equations, a new structural design method of 3D electromagnetic (EM) wave-absorbing woven fabrics was obtained. The 3D woven fabrics fabricated by the proposed method had the structure of a bidirectional angle interlock. Continuous S-2 glass fibers were used as the matching layer of this 3D woven fabric, and continuous carbon fibers were used as the absorbing layer. The absorbing layer satisfied the equivalent EM parameters under the condition of zero reflection. The results of the simulation and experiment showed that the performance trends of the 3D wave-absorbing fabric obtained by this method were consistent with the theory, which verified the correctness of the structure design method. The 3D fabrics obtained by this method have the advantages of wide absorbing frequencies and good absorbing performance (-20 dB). This structural design method also has theoretical guiding significance for the development of 3D wave-absorbing fabrics.

Increasing demand for energy-efficient means of transport has steadily intensified the trend towards lightweight components. Thermoplastic glass fiber composites (organo sheets) play a major role in the production of functional automotive components. Organo sheets are cut, shaped and functionalized by injection molding to produce hybrid components, such as those used in car door modules. The cutting process produces a considerable amount of production waste, which has thus far been thermally recycled. This study develops a closed mechanical recycling process and analyzes the different steps of the process. The offcuts were shredded using two shredding methods and implemented directly in the injection-molding process. Using tensile tests and impact bending tests, the material properties of the recycled materials were compared with the virgin material. In addition, fiber length degradation via the injection-molding process and the influence of the waterjet-cutting process on the mechanical properties are investigated. Recycled offcuts are both comparable to new material in terms of mechanical properties and usability, and are also economically and ecologically advantageous. Recycling polypropylene waste with glass fiber reinforcement in a closed loop is an effective way to reduce industrial waste in a sustainable and economical production process.

This study aimed to fabricate nano-hydroxyapatite (nHA) grafted/non-grafted E-glass-fiber-based (nHA/EG) and E-glass fiber (EG) orthodontic retainers and to compare their properties with commercially available retainers. Stainless-steel (SS) retainers and everStick Ortho (EST) were used as control groups. The retainers were evaluated with Raman spectroscopy and bonded to bovine teeth. The samples were fatigued under cyclic loading (120,000 cycles) followed by static load testing. The failure behavior was evaluated under an optical microscope and scanning electron microscope. The strain growth on the orthodontic retainers was assessed (48h and 168h) by an adhesion test using Staphylococcus aureus and Candida albicans . The characteristic peaks of resin and glass fibers were observed, and the debonding force results showed a significant difference among all of the groups. SS retainers showed the highest bonding force, whereas nHA/EG retainers showed a non-significant difference from EG and EST retainers. SS retainers' failure mode occurred mainly at the retainer-composite interface, while breakage occurred in glass-fiber-based retainers. The strains' adhesion to EST and EG was reduced with time. However, it was increased with nHA/EG. Fabrication of nHA/EG retainers was successfully achieved and showed better debonding force compared to other glass-fiber-based groups, whereas non-linear behavior was observed for the strains' adhesion.

A considerable effort to understand the bolted joints' mechanical behavior in pultruded profiles has existed in the literature over the past decades. However, most investigations focused on the single-bolt connections, and only a few works considered single-lap joints. This paper investigates the mechanical performance of a single-lap connection of pultruded glass fiber-reinforced polymer (GFRP) plates owning to the experimental data deficit in the literature. Tensile tests of specimens with different geometries generate a database comprising 80 single-bolt joints. The shear-out failure was predominant for the considered GFRP pultruded plates, with the end length mainly affecting the load-bearing capacity. Hart-Smith's theoretical model overestimated the ultimate resistance of all considered joints-the exceptionally low efficiency of the GFRP composite points out the necessity of additional means for strengthening the drilled connections. Additionally, finite element (FE) software Abaqus simulated the bolted joints; this study employs the user-defined subroutine experimentally verified in the literature. In the considered examples, the ultimate resistance prediction error decreased from 25.7% to 2.9% with increasing the plate thickness (from 4 mm to 8 mm) and width (from 25 mm to 35 mm), which proves the reasonable adequacy of the simplified FE model and makes it a valuable reference for further bolted joints' development.

Combining two types of reinforcement fiber in a common matrix may lead to different failure modes such as micro-cracks between the layers when the structure is subjected to lower stress levels. Real-time damage detection should be integrated into the hybrid composite structure to provide structural integrity and mitigate this problem. This paper outlines the working mechanisms and the fabrication of an integrated capacitive sensor in an intra-ply hybrid composite (2 × 2 twill weave). Uniaxial tensile and flexural tests were conducted to characterize the proposed sensor and provide self-sensing functionality (smart structure). The sensitivity and repeatability of the capacitive sensor were measured to be around 1.3 and 185 µΔ C / Co , respectively. The results illustrate that onset of damage between layers can be detected by in situ monitoring. It can be seen that the initial damage was detected at the turning point where the relative change in capacitance begins to reduce while the load increases. Finite element modeling was also constructed to analyze the test results and explain the reasons behind the turning point. It was shown that the carbon yarns experienced high transverse shear stress (τ xz ) in the crimp region, leading to inter-fiber cracks.

Bird strike, volcanic rock, hailstones, micrometeoroids, or space debris can cause damage to aircraft and space vehicles, therefore their composite materials must have high impact resistance to maximize safety. In a 55% wt. CaCO 3 compression molded short glass fiber polyester GFRP-BMC (bulk molded compound), shortening the nominal 6.4 mm fiber length formulation, by 30 min extended mixing, to 0.44 mm was found to increase Charpy impact values, a uc , without a change in the compression molding equipment. Specimens were cut from square panels in a spiral configuration in conformity with ASTM D 6110-02 for orthotropic panels, the flow direction approximately radially outward from the charge. At a median-fracture probability of P f = 0.50, extended mixing improved a uc by 29%, from 7.43 to 9.59 kJm -2 , and for each solidification texture angle, namely, 0 to 90 (random), 71, 45 and 18 deg, the a uc increased by 25% (6.26 to 7.86 kJm -2 ), 18% (9.36 to 11.07 kJm -2 ), 35% (7.68 to 10.37 kJm -2 ), and 20% (6.96 to 8.36 kJm -2 ), respectively. This strengthening can be explained by an increased number of thermal compressive stress sites between the glass fiber and matrix due to a difference in the coefficient of thermal expansion (CTE) during cool-down, and shrinkage, with an increased number of spaces between fibers, | S f | from 217 to approximately 2950 per mm 3 , enhancing impact energy.

Fiber-reinforced polymers (FRPs) are low-density, high-performance composite materials, which find important applications in the automotive, aerospace, and energy industry, to only cite a few. With the increasing concerns about sustainability and environment risks, the problem of the recycling of such complex composite systems has been emerging in politics, industry, and academia. The issue is exacerbated by the increased use of FRPs in the automotive industry and by the expected decommissioning of airplanes and wind turbines amounting to thousands of metric tons of composite materials. Currently, the recycling of FRPs downcycles the entire composite to some form of reinforcement material (typically for cements) or degrades the polymer matrix to recover the fibers. Following the principles of sustainability, the reuse and recycling of the whole composite-fiber and polymer-should be promoted. In this review paper, we report on recent research works that achieve the recycling of both the fiber and matrix phase of FRP composites, with the polymer being either directly recovered or converted to value-added monomers and oligomers.

Glial cell alignment in tissue engineered constructs is essential for achieving functional outcomes in neural recovery. While gelatin methacrylate (GelMA) hydrogel offers superior biocompatibility along with permissive structure and tailorable mechanical properties, phosphate glass fibers (PGFs) can provide physical cues for directionality of neural growth. Aligned PGFs were fabricated by a melt quenching and fiber drawing method and utilized with synthesized GelMA hydrogel. The mechanical properties of GelMA and biocompatibility of the GelMA-PGFs composite were investigated in vitro using rat glial cells. GelMA with 86% methacrylation degree were photo-crosslinked using 0.1%wt photo-initiator (PI). Photocrosslinking under UV exposure for 60 s was used to produce hydrogels (GelMA-60). PGFs were introduced into the GelMA before crosslinking. Storage modulus and loss modulus of GelMA-60 was 24.73 ± 2.52 and 1.08 ± 0.23 kN/m 2 , respectively. Increased cell alignment was observed in GelMA-PGFs compared with GelMA hydrogel alone. These findings suggest GelMA-PGFs can provide glial cells with physical cues necessary to achieve cell alignment. This approach could further be used to achieve glial cell alignment in bioengineered constructs designed to bridge damaged nerve tissue., (© 2021 The Authors. Journal of Biomedical Materials Research Part A published by Wiley Periodicals LLC.)

In this work, laminated polyester thermoset composites based on palm tree fibers extracted from palms leaflets and glass mats fibers were manufactured to develop hybrid compositions with good mechanical properties; the mixture of fibers was elaborated to not exceed 25 vol.%. Samples were prepared with a resin transfer molding (RTM) method and mechanically characterized using tensile and flexural, hardness, and impact tests, and ultrasonic waves as a non-destructive technique. The water sorption of these composite materials was carried out in addition to solar irradiation aging for approximately 300 days to predict the applicability and the long-term performance of the manufactured composites. Results have shown that the use of glass fibers significantly increased all properties; however, an optimum combination of the mixture could be interesting and could be developed with less glass sheet and more natural fibers, which is the goal of this study. On the other hand, exposure to natural sunlight deteriorated the mechanical resistance of the neat resin after only 60 days, while the composites kept high mechanical resistance for 365 days of exposure.

Embedded sensors are key to optimizing processes and products; they collect data that allow time, energy, and materials to be saved, thereby reducing costs. After production, they remain in place and are used to monitor the long-term structural health of buildings or aircraft. Fueled by climate change, sustainable construction materials such as wood and fiber composites are gaining importance. Current sensors are not optimized for use with these materials and often act as defects that cause catastrophic failures. Here, flexible, highly permeable, and imperceptible sensors (iSens) are introduced that integrate seamlessly into a component. Their porous substrates are readily infused with adhesives and withstand harsh conditions. In situ resistive temperature measurements and capacitive sensing allows monitoring of adhesives curing as used in wooden structures and fiber composites. The devices also act as heating elements to reduce the hardening time of the glue. Results are analyzed using numerical simulations and theoretical analysis. The suggested iSens technology is widely applicable and represents a step towards realizing the Internet of Things for construction materials., (© 2021 The Authors. Advanced Materials published by Wiley-VCH GmbH.)

Background: Restoration of endodontically treated teeth is one of the most challenging part of operative dentistry. The introduction of fiber-reinforced composite has provided a considerable opportunity to modify material's behavior and to enhance the response of existing materials., Aim: The aim of the study is to comparatively evaluate the efficacy of fiber-reinforced composite resins and nanohybrid resin impregnated with glass fibers as postendodontic restoration in molars., Materials and Methods: Fifty patients with deep occlusal carious lesion requiring root canal treatment were selected and treated. For postendodontic restoration, it was divided into Group A (Interlig) and Group B (ever-X posterior) which were eventually restored according to the manufacturer's instructions. Patients were recalled for evaluation at 3-, 6-, 12-month interval. The restorations were evaluated according to modified United States Public Health Service Criteria., Statistical Analysis: Chi-square test was used for intergroup comparison., Results: A statistically significant difference was noted in terms of fracture of tooth and ever-X posteriors proved to be a superior material and no statistically significant difference observed for marginal discoloration, marginal integrity, fracture of core-build up and secondary caries at the evaluation period of 1 year., Conclusion: Ever-X posteriors performed better than Interlig group as postendodontic restoration after 1 year of evaluation., Competing Interests: There are no conflicts of interest., (Copyright: © 2022 Journal of Conservative Dentistry.)

In the current study, the utilization of glass and nylon fibers in various percentages are added to enhance the mechanical performance of peach shell lightweight concrete. Glass and nylon fibers were added at 2%, 4%, 6%, and 8% by cement weight. The results showed that, as we added the glass and nylon fibers, the density of peach shell concrete was reduced by 6.6%, and the compressive, split tensile and flexural strength were enhanced by 10.20%, 60.1%, and 63.49%. The highest strength that was obtained in compressive, split tensile, and flexural strength at 56 days was 29.4 MPa, 5.2 MPa, and 6.3 MPa, respectively, with 6% of glass fiber in peach shell concrete. Mechanical test results showed that post-failure toughness and modulus of elasticity of peach shell concrete is enhanced with the utilization of fibers. To verify our lab results, a statistical analysis, such as response surface methodology, was performed to make a statistical model, it was confirmed by both lab results and statistical analysis that the mechanical performance of peach shell concrete could be significantly improved by adding glass fibers as compared to nylon fibers. With the use of fibers, the water absorption and porosity were slightly increased. Hence, the glass and nylon fibers can be used to improve the peach shell concrete mechanical properties to make concrete eco-friendly, sustainable, and lightweight.

Impact resistance is one of the most critical features of composite structures, and therefore, its examination for a new material has a fundamental importance. This paper is devoted to the characterization of the fully recyclable thermoplastic ELIUM acrylic resin reinforced by glass fabric woven, which belongs to a new category of materials requiring advanced testing before their application in responsible elements of engineering structures. Its high strength, low weight as well as low production cost give excellent opportunities for its wide application in the automotive industry as a replacement of the thermoset-based laminates. The study presents an experimental work concerning the effect of damage due to low and high cyclic fatigue aging of two groups of specimens, first with the woven fabric orientations of [0°/90°] 4 and secondly with [45°/45°] 4 , on the low impact velocity properties. The impact resistance was measured in terms of load peak, absorbed energy, penetration threshold and damage analysis. The low velocity impact results indicate that the uniaxial cyclic loading (fatigue aging) of the material leads to the reduction of impact resistance, especially at the high impact energy levels. Scanning Electron Microscopy (SEM) and Computed Tomography (CT) scan observations reveal that the damage area grows with the increase of both strain amplitude and impact energy.

Currently, composite materials dominate among the restorative materials used for direct aesthetic filling. Reinforcement of composites with glass fibers allows for the transfer of greater loads and better durability between the tooth tissue and the filling polymer. New approach to bonding liquid materials with composite with glass fillers is to introduce an additional protective barrier to load a higher force that is, compression test. So, the aim of the study was to analyze the structure of composite fillings, their integrity with tooth tissues and evaluation on the influence of the liquid composite layer on the strength of strength in the compression test. Moreover, the influence of thermal shocks on the bonding with the tooth tissues in the compression test was investigated. According to the results obtained in current research, using the flow composite as a combination with the fiber composite leads to a significant increase in mechanical properties, particularly in the compression test. HIGHLIGHTS: If flow-type composite fluid material are, the greater is strength of composite fillings. Glass fibers composite increase the mechanical strength., (© 2021 Wiley Periodicals LLC.)

UD glass/PA6 coupons with an open hole are subjected to tensile and compressive loading. Three layups: [0/90] 5s , [+45/-45] 5s and [+45/0/-45/90] 3s with a shape based on ASTM D5766 were tested. Both monotonic loading as well as loading-unloading-reloading tests were executed. The strain field on the sample surface was measured with digital image correlation. This allowed identifying the distribution of the strain field during loading, permanent deformation and the evolution of the sample elastic modulus. This information is not frequently measured. Yet, it is vital for the development and validation of advanced failure models. The results indicate that the thermoplastic matrix allows large plastic deformation under tensile loading for the specimens with layup [+45/-45] 5s . In addition, the specimen elastic modulus reduces by about 70%. The other layups show minor permanent deformation, while the elastic modulus reduces by up to 15%. Furthermore, the quasi-isotropic laminate shows a significant post-failure load-bearing capacity under compression loading. The results are complemented with post-mortem damage and fracture observations using optical microscopy and ultrasound inspection.

Due to the sharp and corrosion-prone features of steel fibers, there is a demand for ultra-high-performance concrete (UHPC) reinforced with nonmetallic fibers. In this paper, glass fiber (GF) and the high-performance polypropylene (HPP) fiber were selected to prepare UHPC, and the effects of different fibers on the compressive, tensile and bending properties of UHPC were investigated, experimentally and numerically. Then, the damage evolution of UHPC was further studied numerically, adopting the concrete damaged plasticity (CDP) model. The difference between the simulation values and experimental values was within 5.0%, verifying the reliability of the numerical model. The results indicate that 2.0% fiber content in UHPC provides better mechanical properties. In addition, the glass fiber was more significant in strengthening the effect. Compared with HPP-UHPC, the compressive, tensile and flexural strength of GF-UHPC increased by about 20%, 30% and 40%, respectively. However, the flexural toughness indexes I 5 , I 10 and I 20 of HPP-UHPC were about 1.2, 2.0 and 3.8 times those of GF-UHPC, respectively, showing that the toughening effect of the HPP fiber is better.

In this paper, we report a study on the effects of different ethylene copolymers in improving the impact strength of a fiber-reinforced composite based on a recycled poly(ethylene terephthalate) (rPET) from post-consumer bottles. Different ethylene copolymers have been selected in order to evaluate the effects of the polar co-monomer chemical structure and content. The composite mixtures were prepared via melt extrusion, and the samples were manufactured by injection molding. Impact strength was evaluated using Izod tests, and a morphological study (FESEM) was performed. As a result, a composite with substantially improved impact properties was designed. This study demonstrates that a post-consumer PET from the municipal waste collection of plastic bottles can be successfully used as a matrix of high-performance, injection-molded composites, suitable for use in the automotive sector, among others, with no compromise in terms of mechanical requirements or thermal stability.

The principal objective of the work is to compare among carbon-glass filament wound epoxy matrix hybrid composites with a different fiber ratio made by robotized winding processes and optimize the geometry suitable for the Rocket Propelled Grenade Launcher. ANSYS based finite element analysis was used to predict the axial as well as radial compression behavior. Experimental samples were developed by a robot-controlled filament winding process that was incorporated with continuous resin impregnation. The experimental samples were evaluated for the corresponding compressional properties. Filament wound tubular composite structures were developed by changing the sequence of stacking of hoop layers and helical layers, and also by changing the angle of wind of the helical layers while keeping the sequence constant. The samples were developed from carbon and glass filaments with different carbon proportions (0%, 25%, 50%, 75%, and 100%) and impregnated with epoxy resin. The compressional properties of the tubular composites that were prepared by filament winding were compared with the predicted axial and radial compressional properties from computational modelling using the finite element model. A very high correlation and relatively small prediction error was obtained.

The concrete industry has long been adding discrete fibers to cementitious materials to compensate for their (relatively) low tensile strengths and control possible cracks. Extensive past studies have identified effective strategies to mix and utilize the discrete fibers, but as the fiber material properties advance, so do the properties of the cementitious composites made with them. Thus, it is critical to have a state-of-the-art understanding of not only the effects of individual fiber types on various properties of concrete, but also how those properties are influenced by changing the fiber type. For this purpose, the current study provides a detailed review of the relevant literature pertaining to different fiber types considered for fiber-reinforced concrete (FRC) applications with a focus on their capabilities, limitations, common uses, and most recent advances. To achieve this goal, the main fiber properties that are influential on the characteristics of cementitious composites in the fresh and hardened states are first investigated. The study is then extended to the stability of the identified fibers in alkaline environments and how they bond with cementitious matrices. The effects of fiber type on the workability, pre- and post-peak mechanical properties, shrinkage, and extreme temperature resistance of the FRC are explored as well. In offering holistic comparisons, the outcome of this study provides a comprehensive guide to properly choose and utilize the benefits of fibers in concrete, facilitating an informed design of various FRC products.

The paper describes the mechanical properties, determined on the basis of a tensile strength test of a composite material based on glass-fiber reinforced polyamide and obtained by Selective Laser Sintering-SLS. The material used is PA 3200 GF. Thin walled samples with non-standard nominal thicknesses of 1, 1.4 and 1.8 mm, manufactured in three printing directions X, Y and Z, were used. The description included the impact of printing direction on the geometry of the obtained samples and tensile strength as well as the dependency of tensile strength on the sample thickness. The results can be useful for design engineers and process engineers designing thin-walled components produced with SLS. Thin samples were obtained with a considerable deviation spread of the actual dimension from the nominal one. It was found that the tensile strength of thin samples is much lower than those of standard cross-sections, which should be taken into account in the design of thin-walled elements.