Search

Here, we describe novel, chemically cross-linked, self-molding particulate polymer sorbents that are utilized as a molding-type solid-phase extraction medium (M-SPEM), which exhibits high permeability and rigidness. To fabricate such M-SPEM, first, polyethyleneimine (PEI)-modified reversed-phase (RP)-type particulate sorbents were synthesized, thereafter, they were chemically cross-linked by a polymer having many epoxy groups together with additional PEI. By optimizing the binding conditions of the particulate sorbents, the resultant M-SPEM has almost the same adsorption properties as the corresponding unmolded particulate sorbent for some polar (e.g., uracil and adenine) compounds. The binding technique proposed here is expected to facilitate the fabrication of molding-type sorbents and improve the performance of the SPE procedure., (© 2022. The Author(s), under exclusive licence to The Japan Society for Analytical Chemistry.)

Hydrophilic interaction chromatography (HILIC)-type sorbents were newly developed for the solid-phase extraction (SPE) of polar compounds. Two methacrylate-base resins with different cross-linking monomers and pore properties were synthesized, and three polyethyleneimines (PEIs) with different molecular weights were modified onto each base resin. In both cases, PEIs with a molecular weight of 10,000 (PEI-10,000) exhibited the highest adsorption properties for polar compounds (uracil, uridine, adenosine, cytidine, and guanosine). To control the water-enriched layer at the surface of the PEI-10,000-modified sorbents, the additive amount of PEI-10,000 in the modified reaction was also optimized. When 10 times the amount of PEI-10,000 to each base resin was added, an improvement in adsorption property was observed. Moreover, the use of a nonaqueous sample solution (100% acetonitrile) during the sample loading process drastically improved adsorption, especially for uracil (about 80%) and adenosine (100%). These results indicate that the formation of a strong water-enriched layer at the surface of sorbents with an effective expression of hydrophilic interaction was an important factor in the adsorption properties of polar compounds in HILIC mode-SPE., (© 2022. The Author(s), under exclusive licence to The Japan Society for Analytical Chemistry.)

A simple and low-cost method of fabricating an optical fiber for a surface plasmon resonance (SPR) sensor was proposed. The method is based on the electroless nickel plating and subsequent displacement gold plating of the core of the optical fiber. The thickness of the nickel and gold thin films deposited on the core of the optical fiber could be controlled by measuring the reflected light intensity from the tip of the optical fiber during the plating processes. The sensitivity and resolution of the SPR sensor with the fabricated optical fiber in the refractive index range from 1.333 to 1.348 were 1324.3 nm/RIU and 7.6 × 10 -4 RIU, respectively. The developed SPR sensor was successfully used in the determination of immunoglobulin A (IgA) in human saliva. The IgA quantification results obtained by the SPR sensor were in excellent agreement with those obtained by conventional enzyme-linked immunosorbent assay using a 96-well microtiter plate., (Copyright © 2021 Elsevier B.V. All rights reserved.)

A fabrication method of molding-type solid-phase extraction media (M-SPEM) bound with commercially available adhesive is presented. Six pieces of M-SPEM were prepared by heating each kneaded product of a particulate sorbent and an adhesive inserted into a six-hole cylindrical mold for hardening under an open system and normal pressure. The particulate sorbent contained in M-SPEM was divinylbenzene-based reversed-phase mode solid-phase extractants that we have reported. An examination of several adhesives showed that the moldability of M-SPEM depended on the composition and properties of the adhesive. The optimized procedure can be used to prepare an M-SPEM containing an 85 wt% particulate sorbent (particulate sorbent/adhesive, 100 mg/17 mg; particle diameter, 90-150 µm), and the M-SPEM has a specific surface area of about 500 m 2 /g. The established procedure in this study can bind particulate sorbents together, which showed almost no reductions in the adsorption property and liquid permeability compared with those of the particulate sorbent., (© 2022. The Author(s), under exclusive licence to The Japan Society for Analytical Chemistry.)

We developed a small fluorescence microplate reader with an organic photodiode (OPD) array. The OPD array has nine OPDs that have a large light receiving area (9.62 mm 2 per one OPD). Since the OPD array is fabricated on a flat glass plate, it can be placed just below microwells and can detect fluorescence emitted through the entire surface of the microwell bottom. The analytical performance of the developed plate reader was evaluated by measuring an aqueous solution of resorufin. The limit of detection (LOD) for resorufin (0.01-0.05 μM) was lower than that obtained with a plate reader equipped with nine inorganic photodiodes developed in a previous study (0.30 μM) and a commercially available microplate reader (0.16 μM). These results indicate that the large light receiving area improves the detection performance of the system. In addition, the developed reader was successfully used to quantify immunoglobulin A (IgA) in human saliva. The LOD for IgA was estimated to be 1.2 ng/mL, which is low enough to objectively evaluate human stress., (Copyright © 2021 Elsevier B.V. All rights reserved.)

With the aim of developing efficient flow-through microreactors for high-throughput organic synthesis, in this work, microreactors were fabricated by chemically immobilizing palladium-, nickel-, iron-, and copper-based catalysts onto ligand-modified poly(glycidyl methacrylate- co -ethylene dimethacrylate) [poly(GMA- co -EDMA)] monoliths, which were prepared inside a silicosteel tubing (10 cm long with an inner diameter of 1.0 mm) and modified with several ligands including 5-amino-1,10-phenanthroline (APHEN), iminodiacetic acid (IDA), and iminodimethyl phosphonic acid (IDP). The performance of the resulting microreactors in Suzuki-Miyaura cross-coupling reactions was evaluated, finding that the poly(GMA- co -EDMA) monolith chemically modified with 5-amino-1,10-phenanthroline as a binding site for the palladium catalyst provided an excellent flow-through performance, enabling highly efficient and rapid reactions with high product yields. Moreover, this monolithic microreactor maintained its good activity and efficiency during prolonged use.

In response to cholesterol deprivation, SCAP escorts SREBP transcription factors from the endoplasmic reticulum to the Golgi complex for their proteolytic activation, leading to gene expression for cholesterol synthesis and uptake. Here, we show that in cholesterol-fed cells, ER-localized SCAP interacts through Sac1 phosphatidylinositol 4-phosphate (PI4P) phosphatase with a VAP-OSBP complex, which mediates counter-transport of ER cholesterol and Golgi PI4P at ER-Golgi membrane contact sites (MCSs). SCAP knockdown inhibited the turnover of PI4P, perhaps due to a cholesterol transport defect, and altered the subcellular distribution of the VAP-OSBP complex. As in the case of perturbation of lipid transfer complexes at ER-Golgi MCSs, SCAP knockdown inhibited the biogenesis of the trans-Golgi network-derived transport carriers CARTS, which was reversed by expression of wild-type SCAP or a Golgi transport-defective mutant, but not of cholesterol sensing-defective mutants. Altogether, our findings reveal a new role for SCAP under cholesterol-fed conditions in the facilitation of CARTS biogenesis via ER-Golgi MCSs, depending on the ER cholesterol., (© 2020 Wakana et al.)

The handling of a particulate sorbent for solid-phase extraction is often troublesome because it causes static clinging and scattering. To overcome this problem, a production method for a simple molding-type solid-phase extraction medium (M-SPEM) was developed in this study by using commercially available adhesives. The content of a particulate sorbent can increase to as much as 85 wt% in the M-SPEM. Because of the high content, the proposed M-SPEMs have a higher specific surface area than previous monolithic media.

Hydrophilic interaction chromatography (HILIC) has attractive attention for the separation of water-soluble compounds via HPLC. There are, however, few studies on the pretreatment of the HILIC-type solid-phase extraction (SPE) due to the difficulty of obtaining the HILIC-type sorbent. Therefore, the development of HILIC-type sorbents for SPE is essential. In this study, four different hydrophilic copolymers, namely diallylamine-maleic acid copolymer (DAM), diallylamine-acrylamide copolymer (DAA), allylamine-maleic acid copolymer (MAM), and partly methylcarbonylated allylamine acetate copolymer (MAC), were immobilized on glycidyl methacrylate (GMA)-base resin, and their adsorptive properties were evaluated. The results of the physical and adsorptive properties indicated that a balance between the water content of the water-enriched layer on sorbent and the amount of hydrophilic copolymer immobilized on the GMA-base resin was vital for the adsorption in HILIC-type sorbent for SPE.

We developed hydrophilic interaction chromatography (HILIC)-type sorbents modified with nucleobases for solid phase extraction (SPE). The synthesized hydrophilic base resins were modified by each nucleobase (adenine, guanine, and cytosine). The measurement of the amount of water content indicated that each nucleobase-modified sorbent had a water layer. To evaluate the adsorption properties in the HILIC mode, we chose two nucleobases (uracil and adenine) and four nucleosides (uridine, adenosine, cytidine, guanosine) as water-soluble analytes, which were loaded into an SPE cartridge packed with the nucleobase-modified sorbent. Firstly, 95% acetonitrile (ACN) solutions were used in the process of conditioning and sample loading of the above polar analytes. High recoveries of the analytes were observed in each nucleobase-modified sorbent, and the Diol-type sorbent (no modification with any of the nucleobases) did not adsorb each water-soluble analyte. On the basis of this result, a 98% ACN solution was used during the process of conditioning and sample loading to decrease the concentration of water in the sample, which potentially inhibited the formation of hydrogen bonding between each analyte and the modified nucleobase. Considerable improvements of recoveries were observed in Adenine- and Cytosine-modified sorbents. These results were possibly attributed to the effective expression of hydrogen bonding by decreasing water concentration in the sample solution. Although a non-aqueous (100% ACN) sample solution can be expected to obtain higher recoveries compared with the 98% ACN solution, a decrease in recoveries was observed in Adenine-modified sorbent. From these results, the highest adsorption property was observed in Adenine-modified sorbent using 98% ACN as a sample condition, and the combination of this sample condition and sorbent is effective for high adsorption under HILIC condition. Moreover, we also revealed that a balance between the thickness of water layer and the modification amount of nucleobase is important for retention in the HILIC-type sorbent., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

A highly sensitive method for determining urine homogentisic acid (HGA) is required to provide adequate diagnosis and therapy for alkaptonuria in early stages. In this study, we developed a highly sensitive high-performance liquid chromatography with electrochemical detection (HPLC-ECD) for determining HGA in urine. In order to obtain a chromatogram of HGA by HPLC-ECD, an oxidation current was monitored at +0.5 V vs. Ag/AgCl. The peak heights of HGA showed linearity (r = 0.999) ranging from 4.2 ng/mL to 168 ng/mL, and the detection limit was 1.2 ng/mL (signal-to-noise ratio, S/N = 3). In recovery tests using human control urine spiked with an HGA standard, the recoveries of HGA were more than 93.2 %, and the relative standard deviations (n = 6) were less than 1.9 %. As an in vivo application using male Wistar rats, the level of urine HGA, which was metabolized from tyrosine in tyrosine-enriched food, was determined by this HPLC-ECD method. The determination of HGA in urine by this HPLC-ECD method requires only 0.1 mL of a rat urine specimen and simple sample preparation consisting of dilution and filtration., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

A multiple channel-type concentric grid nebulizer (m-CGrid) was developed for realizing efficient online standard addition in inductively coupled plasma optical emission spectrometry (ICP-OES) without premixing of liquids before nebulization. The m-CGrid can nebulize two independent liquids without premixing due to a unique structure, having two independent liquid-flow capillaries inside a single nozzle and a grid screen (over 350 mesh per inch) placed on the hole of the nozzle. The grid acts as both a flow damper and sieve; two liquids are well-mixed with a gas flow in a small space just before the grid screen, and the mixture breaks up into small droplets by passing through the grid. The m-CGrid nebulizer provides almost the same or better spray performance compared with a conventional nebulizer, such as Meinhard nebulizer; the primary aerosols were much finer (D 50 : 2.9 and 3.1 μm for two channels) than those generated with Meinhard nebulizer type C (D 50 : 19.5 μm). The signal intensities in ICP-OES obtained with two liquid channels were almost the same and were 2- to 3-fold higher than that obtained with the Meinhard nebulizer for 23 elements. The performance of m-CGrid in an online standard addition was demonstrated in the analysis of NIST SRM1577b bovine liver and NIES No. 3 Chrorella. The analytical results were in good agreement with their certified values.

Long noncoding RNAs (lncRNAs) are non-protein-coding transcripts >200 nucleotides in length that have been shown to play important roles in various biological processes. The mechanisms underlying the induction of lncRNA expression by chemical exposure remain to be determined. We identified a novel class of short-lived lncRNAs with half-lives (t 1/2 ) ≤4 hours in human HeLa Tet-off cells, which have been suggested to express many lncRNAs with regulatory functions. As they may affect various human biological processes, short-lived lncRNAs may be useful indicators of the degree of stress on chemical exposure. In the present study, we identified four short-lived lncRNAs, designated as OIP5-AS1, FLJ46906, LINC01137, and GABPB1-AS1, which showed significantly upregulated expression following exposure to hydrogen peroxide (oxidative stress), mercury II chloride (heavy metal stress), and etoposide (DNA damage stress) in human HepG2 cells. These lncRNAs may be useful indicators of chemical stress responses. The levels of these lncRNAs in the cells were increased because of chemical stress-induced prolongation of their decay. These lncRNAs were degraded by nuclear RNases, which are components of the exosome and XRN2, and chemical exposure inhibited the RNase activities within the cells.

When iminodiacetic acid chelating-resin solid phase extraction (SPE) was used for the preconcentration of rare earth elements (REEs) in river water samples around sewage treatment plant (STP), low recovery values for heavy REEs were observed. In order to find out the reason for the low recovery, in the present paper, organic ligands in the STP effluent, which may compete with iminodiacetic acids, were analyzed by GC-NPD. It was found that EDTA was contained in the STP effluent at several-100 nM level and interfered with the adsorption of REEs, especially heavy REEs (present at pM level) on the chelating-resin due to the formation of stable complexes. Therefore, acid treatment was applied to decompose EDTA molecules. As a result of acid treatment with HNO 3 and H 2 O 2 at 170 °C for 4 h, all REEs were almost quantitatively recovered from the STP effluent with chelating-resin SPE with good reproducibility. After the acid treatment and subsequent 40-times preconcentration with SPE, all REEs in river water samples were precisely determined by ICP-MS at several-10 to sub pg mL -1 levels., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

Coccolithophorids, unicellular marine microalgae, have calcified scales with elaborate structures, called coccoliths, on the cell surface. Coccoliths generally comprise a base plate, CaCO 3 , and a crystal coat consisting of acidic polysaccharides. In this study, the in vitro calcification conditions on the base plate of Pleurochrysis haptonemofera were examined to determine the functions of the base plate and acidic polysaccharides (Ph-PS-1, -2, and -3). When EDTA-treated coccoliths (acidic polysaccharide-free base plates) or low pH-treated coccoliths (whole acidic polysaccharide-containing base plates) were used, mineralization was not detected on the base plate. In contrast, in the case of coccoliths which were decalcified by lowering of the pH and then treated with urea (Ph-PS-2-containing base plates), distinct aggregates, probably containing CaCO 3 , were observed only on the rim of the base plates. Energy dispersive X-ray spectroscopy (EDS) confirmed that the aggregates contained Ca and O, although X-ray diffraction analysis did not reveal any evidence of crystalline materials. Also, in vitro mineralization experiments performed on EDTA-treated coccoliths using isolated acidic polysaccharides demonstrated that the Ca-containing aggregates were markedly formed only in the presence of Ph-PS-2. Furthermore, in vitro mineralization experiments conducted on protein-extracted base plates suggested that the coccolith-associated protein(s) are involved in the Ca deposition. These findings suggest that Ph-PS-2 associated with the protein(s) on the base plate rim initiates Ca 2+ binding at the beginning of coccolith formation, and some other factors are required for subsequent calcite formation.

Electrochemically active bacteria (EAB) receive considerable attention for their utility in bioelectrochemical processes. Although electrode potentials are known to affect the metabolic activity of EAB, it is unclear whether EAB are able to sense and respond to electrode potentials. Here, we show that, in the presence of a high-potential electrode, a model EAB Shewanella oneidensis MR-1 can utilize NADH-dependent catabolic pathways and a background formate-dependent pathway to achieve high growth yield. We also show that an Arc regulatory system is involved in sensing electrode potentials and regulating the expression of catabolic genes, including those for NADH dehydrogenase. We suggest that these findings may facilitate the use of EAB in biotechnological processes and offer the molecular bases for their ecological strategies in natural habitats.

Whole transcriptome analyses have revealed a large number of novel long non-coding RNAs (lncRNAs). Although accumulating evidence demonstrates that lncRNAs play important roles in regulating gene expression, the detailed mechanisms of action of most lncRNAs remain unclear. We previously reported that a novel class of lncRNAs with a short half-life (t1/2 < 4 h) in HeLa cells, termed short-lived non-coding transcripts (SLiTs), are closely associated with physiological and pathological functions. In this study, we focused on 26 SLiTs and nuclear-enriched abundant lncRNA, MALAT1(t1/2 of 7.6 h in HeLa cells) in neural stem cells (NSCs) derived from human induced pluripotent stem cells, and identified four SLiTs (TUG1, GAS5, FAM222-AS1, and SNHG15) that were affected by the following typical chemical stresses (oxidative stress, heavy metal stress and protein synthesis stress). We also found the expression levels of LINC00152 (t1/2 of 2.1 h in NSCs), MALAT1 (t1/2 of 1.8 h in NSCs), and their neighboring genes were elevated proportionally to the chemical doses. Moreover, we confirmed that the overexpression of LINC00152 or MALAT1 upregulated the expressions of their neighboring genes even in the absence of chemical stress. These results reveal that LINC00152 and MALAT1 modulate their neighboring genes, and thus provide a deeper understanding of the functions of lncRNAs.

A stable two-phase sheath flow using tetrahydrofuran (THF) for an inner flow and water for an outer flow was formed in a glass capillary, and worked as a stable liquid-core/liquid-cladding optical waveguide (THF/water LLW). Although THF and water were miscible with any ratio, the length of the stable THF/water LLW at 0.9 - 2.1 cm s -1 reached at least 150 mm. The THF/water LLW was applied to the observation of extraction behavior of solvatochromic fluorescence dye, 1-anilino-8-naphtalene sulfonate (ANS), through the THF/water interface. ANS was added to the water phase (clad solution) and its fluorescence, which was excited with the guided light (355 nm) through the LLW, was observed by changing the position of the detector. While the ANS stayed in the region of 70% THF to the end of the LLW without the addition of cationic surfactant, hexadecyltrimethylammonium ion (CTA + ) at pH 3 and 11, the ion-pair of ANS and CTA + was extracted into the higher concentration region of THF with the addition of CTA + at pH 11.

Sulfoquinovosyl diacylglycerol is one of the lipids that construct thylakoid membranes, and is distributed from cyanobacteria to plastids in plants including a red lineage. One of the most primitive red algae, Cyanidioschyzon melorae, similar to cyanobacteria and green plants, possesses homologs of the SQD1 and SQD2 genes that code for UDP-sulfoquinovose and sulfoquinovosyl diacylglycerol synthases, respectively, for the synthesis of sulfoquinovosyl diacylglycerol. We here revealed the structural properties of SQD1 and SQD2 homologs in C. melorae intrinsic to those of the authentic proteins, and verified their enzymatic functions through heterologous expression in cyanobacterial disruptants as to the corresponding genes. The results demonstrated that the system of sulfoquinovosyl diacylglycerol synthesis could have been conserved through evolution of cyanobacteria to plastids in a red lineage, which is compatible with the monophyletic origin of plastids., (Copyright © 2016 Elsevier Inc. All rights reserved.)

The unicellular red alga Galdieria sulphuraria grows efficiently and produces a large amount of biomass in acidic conditions at high temperatures. It has great potential to produce biofuels and other beneficial compounds without becoming contaminated with other organisms. In G. sulphuraria, biomass measurements and glycogen and lipid analyses demonstrated that the amounts and compositions of glycogen and lipids differed when cells were grown under autotrophic, mixotrophic, and heterotrophic conditions. Maximum biomass production was obtained in the mixotrophic culture. High amounts of glycogen were obtained in the mixotrophic cultures, while the amounts of neutral lipids were similar between mixotrophic and heterotrophic cultures. The amounts of neutral lipids were highest in red algae, including thermophiles. Glycogen structure and fatty acids compositions largely depended on the growth conditions., (Copyright © 2015. Published by Elsevier Ltd.)

Trace elemental analysis of single yeast cells with time-resolved inductively coupled plasma mass spectrometry (ICP-MS) was successfully carried out, where a high efficiency cell introduction system (HECIS) consisting of the high performance concentric nebulizer (HPCN) and a low-volume (15 mL) on-axis spray chamber utilizing a sheath gas flow were used. Cell adsorption to the flow injector and sample tubing was reduced with the addition of a simple 4.3 mmol L(-1) of NaCl solution to the cell suspension and cell flowing liquid, allowing consecutive measurements without fear of significant contamination from previous measurements. Initially using a quadrupole mass analyzer ICP-MS (ICP-QMS) at its lowest integration time (10 ms), current spikes corresponding to separate cell events were detected for several elements (Mg, P, Ca, Mn, Fe, Cu, and Zn) on the introduction of the cell suspension. On comparing the number of peaks in the spectrum for phosphorous with the cell count using a haemocytometer, a reproducible cell transport efficiency of 75.0 ± 4.7% was achieved. Preliminary experiments into using time of flight ICP-MS (ICP-TOFMS) for single-cell analysis were carried out, allowing quasi-simultaneous multielement detection. The spectra of Mg, P, Ca, Mn, Fe, Cu, and Zn, with a time resolution of 1 ms were simultaneously obtained in one measurement. A relatively strong correlation was observed for the spectra between P and Zn (correlation factor 0.69), P and Mg (0.63), and Mg and Zn (0.63). These results indicate that the time resolved quasi-simultaneous multielement measurement may be useful for the correlation analysis of multielements in cells.

In this paper, we report on the preparation of a microbore-scale (1 mm i.d.) anion-exchange monolithic column suitable not only for analytical purposes but also for potentially preparative applications. In order to meet the conflicting requirements of high permeability and good mechanical strength, the following two-step procedure was applied. First, an epoxy-containing monolith was synthesized by in situ copolymerization of glycidyl methacrylate (GMA) and ethylene dimethacrylate (EDMA) within the confines of a silicosteel tubing of 1.02 mm i.d. and 1/16" o.d. in the presence of a ternary porogenic mixture of 1-propanol, 1,4-butanediol, and water. The monolithic matrix was subsequently converted into weak anion-exchanger via the ring-opening reaction of epoxy group with diethyl amine. The dynamic binding capacity was 21.4 mg mL(-1) for bovine serum albumin (BSA) at 10% breakthrough. The morphology and porous structure of this monolith were assessed by scanning electron microscope (SEM) and inverse size exclusion chromatography (ISEC). To optimize the separation efficiency, the effects of various chromatographic parameters upon the separation of DNA fragments were investigated. The resulting monolithic anion exchanger demonstrated good potential for the separation of both single- and double-stranded DNA molecules using a gradient elution with NaCl in Tris-HCl buffer (20 mM). Oligodeoxythymidylic acids (dT(12)-dT(18)) were successfully resolved at pH 8, while the fragments of 20 bp DNA ladder, 100 bp DNA ladder, and pBR322-HaeIII digest were efficiently separated at pH 9., (Copyright © 2012 Elsevier B.V. All rights reserved.)

In this paper, we describe a method for the preparation of easy-to-use reversed-phase monolithic microbore columns. Polyetheretherketone (PEEK) tubing with an outer diameter of 1/16″ and an inner diameter of 1.0 mm was used as a column housing (empty column), and in it lauryl methacrylate (LMA) was copolymerized with ethylene dimethacrylate (EDMA). In order to chemically anchor the polymer monolith to the tube wall, the inner wall surface was pretreated by the following two-step procedure. (1) 50% sulfuric acid was filled into the PEEK tubing and left to stand for 6 h to generate sulfonate groups on the surface. (2) After washing with Milli-Q water, the sulfonated PEEK surface was brought into contact with 1 M glycidyl methacrylate in dichloromethane (or acetone) at 40°C for 4 h to introduce methacryloyl groups via the reaction of sulfonate groups and epoxy groups. Mechanical strength and column efficiency of the resulting monoliths were evaluated through the separation of a series of alkylbenzenes in acetonitrile-water (50:50, v/v) eluent over the flow rate range of 50-750 μL/min (corresponding to 1.7-25.5 mm/s). The poly(LMA-co-EDMA) monolith provided acceptable column efficiency of 2000 theoretical plates/10 cm (HETP value of 50 μm) for amylbenzene (separation factor k=40) and low flow resistance of 0.5 MPa/10 cm at a normal flow rate of 50 μL/min. The methacryloylated PEEK tubing tightly held the monolith, and the monolithic column exhibited good pressure resistance up to 15 MPa, allowing rapid separation at a 15-20 fold higher flow rate than normal., (Copyright © 2012 Elsevier B.V. All rights reserved.)

Accurate quantification of DNA is highly important in various fields. Determination of phosphorus by ICP-MS is one of the most effective methods for accurate quantification of DNA due to the fixed stoichiometry of phosphate to this molecule. In this paper, a smart and reliable method for accurate quantification of DNA fragments and oligodeoxythymidilic acids by hyphenated HPLC/ICP-MS equipped with a highly efficient interface device is presented. The interface was constructed of a home-made capillary-attached micronebulizer and temperature-controllable cyclonic spray chamber (IsoMist). As a separation column for DNA samples, home-made methacrylate-based weak anion-exchange monolith was employed. Some parameters, which include composition of mobile phase, gradient program, inner and outer diameters of capillary, temperature of spray chamber etc., were optimized to find the best performance for separation and accurate quantification of DNA samples. The proposed system could achieve many advantages, such as total consumption for small amount sample analysis, salt-tolerance for hyphenated analysis, high accuracy and precision for quantitative analysis. Using this proposed system, the samples of 20 bp DNA ladder (20, 40, 60, 80, 100, 120, 140, 160, 180, 200, 300, 400, 500 base pairs) and oligodeoxythymidilic acids (dT(12-18)) were rapidly separated and accurately quantified., (Copyright © 2011 Elsevier B.V. All rights reserved.)

Clinical research indicates that negative calcium balance is associated with low bone mass, rapid bone loss, and high fracture rates. However, some studies revealed that not only calcium is involved in bone strengthening as risk factor of fracture osteoporosis. Thus, in this report, the difference of metallic and nonmetallic elements in osteoporosis and normal bones was studied by high-resolution inductively coupled plasma mass spectrometry (HR-ICP-MS). The influence of these elements on bone metabolic processes is also discussed. Inclusion criteria of bone samples consist of postmenopausal woman, trabecular bone fracture, normal and osteoporosis BMD value, and no history of previous disease. The results showed that the concentration of B, Al, S, V, Co, Mo, Te, Ba, La, Ni, As, and Ca/P ratio is higher in osteoporosis than normal. These atomic minerals have negative role to imbalance between bone resorption and bone formation activity. Conversely, concentrations of Na, Mg, P, K, Ca, Cr, Pd, Ag, Mn, Fe, Cu, Zn, Rb, Sr, Pb, and Se are lower in osteoporosis than in normal bones. Among these atoms, known to have important roles in bone structure, we found involvement of atomic mineral and calcium which are considerable to contribute to osteoporotic phenomena.

The distributions of eleven elements in a peanut seed were obtained by elemental imaging with laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The distribution of Mo was significantly different to those of other elements, such as K, P, and Mg. It was also confirmed that this typical enrichment of Mo was not dependent on the region where the peanut seed was planted. The enrichment of Mo was observed in the radicle of peanut seed, and was further confirmed by the isotopic ratio of Mo.

A method for multielement analysis of micro-volume biological sample by inductively coupled plasma mass spectrometry (ICP-MS) with a highly efficient sample introduction system was presented. The sample introduction system was the combination of (1) an inert loop injection unit and (2) a high performance concentric nebulizer (HPCN) coupled with a temperature controllable cyclone chamber. The loop injection unit could introduce 20 μL samples into the carrier liquid flow of 10 μL min(-1) producing a stable signal for 100s without any dilution. The injection loop is continuously washed with 0.1M HNO(3) carrier solution during the measurement, thereby much improving sample throughput. The HPCN is a triple tube concentric nebulizer, which can generate fine aerosols and provide a stable and highly measurement sensitivity in ICP-MS at a liquid flow rate less than 10 μL min(-1). With the combination of the chamber heating at 60°C, the sensitivity obtained with the proposed sample introduction system at the liquid flow rate of 10 μL min(-1) was almost the same as that with a common concentric nebulizer and cyclone chamber system at the liquid flow rate of 1 mL min(-1), though the sample consumption rate of the HPCN was two orders of the magnitude lower than that of the common nebulizer. The validation of the proposed system was performed by analyzing the NIST SRM 1577b Bovine Liver. The observed values for 12 elements such as Na, P, S, K, Ca, Mn, Fe, Co, Cu, Zn, Mo, Cd were in good agreement with their certified values and information value. Satisfactory analytical results for 14 elements such as Na, Mg, P, S, K, Ca, Cr, Mn, Fe, Ni, Cu, Zn, Y, Ba in Escherichia coli sample were also obtained. The proposed sample introduction system was quite effective in the cases when only micro-volume of biological sample is available., (Copyright © 2011 Elsevier B.V. All rights reserved.)

Adipose tissue-derived stem cells (ASCs) have shown promise in cell therapy because of their ability to self-renew damaged or diseased organs and easy harvest. To ensure the distribution and quantification of the ASCs injected from tail vein, several whole-body imaging techniques including fluorescence optical imaging with quantum dots (QDs) have been employed, but they may suffer from insufficient sensitivity and accuracy. Here, we report quantitative distribution of ASCs in various organs (heart, lung, liver, spleen, and kidney) of mice, which were intravenously injected with QDs-labeled ASCs (QDs-ASCs), through the detection of QDs-derived metallic components by inductively coupled plasma mass spectrometry (ICPMS). For accurate and precise determination, each organ was harvested and completely digested with a mixture of HNO(3) and H(2)O(2) in a microwave oven prior to ICPMS measurement, which was equipped with a microflow injection system and a laboratory-made capillary-attached micronebulizer. After optimization, 16 elements including major components (Cd, Se, and Te) of QDs and essential elements (Na, K, Mg, Ca, P, S, Mn, Fe, Co, Cu, Zn, Se, Sr, and Mo) were successfully determined in the organs. As compared to untreated mice, QDs-ASCs-treated mice showed significantly higher levels of Cd and Te in all organs, and as expected, the molar ratio of Cd to Te in each organ was in good agreement with the molar composition ratio in the QDs. This result indicates that the increment of Cd (or Te) can be used as a tracer for calculating the distribution of ASCs in mice organs. As a result of the calculation, 36.8%, 19.1%, 0.59%, 0.49%, and 0.25% of the total ASCs injected were estimated to be distributed in the liver, lung, heart, spleen, and kidney, respectively.

Poly(lauryl methacrylate-co-ethylene dimethacrylate) monoliths were in situ synthesized within the confines of a silicosteel tubing of 1.02 mm i.d. and 1/16" o.d. for microbore reversed-phase HPLC. In order to obtain practically useful monoliths with adequate column efficiency, low flow resistance, and good mechanical strength, some parameters such as total monomer concentration (%T), cross-linking degree (%C) and polymerization temperature were optimized. High-efficiency monoliths were successfully obtained by thermal polymerization of a monomer mixture (40%T, 10%C) with a binary porogenic solvent consisting of 1-propanol and 1,4-butandiol (7:4, v/v) at a high temperature of 90 °C. The morphology and porous structure of the resulting monoliths were assessed by scanning electron microscope (SEM) and inverse size exclusion chromatography (ISEC), while the column performance was evaluated through the separations of a series of alkylbenzenes in acetonitrile-water (50:50, v/v) eluent. At a normal flow rate of 50 μL/min (corresponding to 1.66 mm/s), the optimized monolithic columns typically exhibited theoretical plate numbers of 6000 plates/10 cm-long column for amylbenzene (k>40), and the pressure drop was always less than 1 MPa/10 cm. The monoliths, which were chemically anchored to the tube inner wall surface using a bifunctional silylation agent, exhibited adequate mechanical strength of up to 12-13 MPa, and were properly operated at 10 times higher flow rate than normal, reducing the separation time to one tenth. The lauryl methacrylate-based monolithic column was applied to a rapid and efficient separation of ten common proteins such as aprotinin, ribonuclease A, insulin, cytochrome c, trypsin, transferrin, conalbumin, myoglobin, β-amylase, and ovalbumin in the precipitation-redissolution mode. Using a linear CH(3)CN gradient elution at a flow rate of 500 μL/min (10-times higher flow rate), 10 proteins were baseline separated within 2 min., (Copyright © 2011 Elsevier B.V. All rights reserved.)

A syringe-based sample pretreatment tool, named herein "tip-in chelating monolith", has been developed for simple and facile solid phase microextraction (SPME) of trace elements in natural waters. The tip-in chelating monolith was directly prepared within the confines of a commercially available syringe filter tip by a two-step process: (1) in situ polymerization of a monomer solution consisting of 22.5% glycidyl methacrylate (GMA), 7.5% ethylene glycol dimethacrylate (EDMA), 35% 1-propanol, 28% 1,4-butanediol, and 7% water and (2) its subsequent modification with 1molL(-1) of iminodiacetate solution (adjusted to pH 10) via ring-opening reaction of epoxide. The adsorption properties of the tip-in chelating monolith thus obtained were evaluated through an adsorption/desorption experiment, where the effects of sample solution pH and eluent on the SPME of trace metals and metalloids were systematically examined. Consequently, when sample solution pH was adjusted to 5.0 and 0.9mL of 2molL(-1) nitric acid was used as an eluent, good recoveries of more than 80% were obtained for 27 elements in a single-step extraction. The proposed SPME method was validated through the analysis of two river water certified reference materials (CRMs: JSAC 0301-1 and NMIJ 7201-a). After 50-fold preconcentration (from 50mL of the original river water sample to 1.0mL of final analysis solution), 22 trace elements including Ti, Fe, Co, Ni, Cu, Ga, Cd, Sn and REEs were quantitatively determined by inductively coupled plasma mass spectrometry (ICP-MS). The analytical detection limits were in the range from 0.000003microgL(-1) for Ho to 0.18microgL(-1) for Fe. Good agreement of the observed values with the certified or reference values indicates that the proposed SPME using the tip-in chelating monolith is practically applicable.

Metal ions were determined by ESI-MS in the negative ion mode as monovalent negative ions of their aminopolycarboxylic acid (APC) complexes, e.g., [Al(cydta)](-), [Pb(Hcydta)](-), where excess amounts of the APC agents were added to sample solutions. Among several APCs studied, we chose trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid (CyDTA) as the best chelating agent because of higher stabilities and higher sensitivities of the complexes. The ionization efficiency of these metal complexes was strongly affected by the presence of matrix salts, e.g., NaCl, KNO(3), and etc. Thus, a size exclusion column (Sephadex G-10) was used for the online separation of the metal-APC complexes from other matrix salts. This method was successfully applied to the quantitative analyses for total amounts of Al, Ni, Cu, Zn, and Pb in the biological certified reference materials, olive leaves (BCR-062) and plankton (BCR-414). The detection limits of the present methods for these elements were several to several ten nanomolar levels. Moreover, this approach was extended to determine ultratraces of fluoride based on the formation of the ternary complex of aluminum, fluoride and nitrilotriacetic acid (NTA), i.e., [AlF(nta)](-). Its detection limit was 10 nM and was 2 orders of magnitude better than that of a fluoride ion selective electrode method. This method was applied to determine fluoride in tap water, river water, and green tea samples.

A syringe-driven chelating column (SDCC) was applied to develop an on-line preconcentration/inductively coupled plasma mass spectrometry (ICP-MS) method for preconcentration and determination of rare earth elements (REEs) in seawater samples. The present on-line preconcentration system consists of only one pump, two valves, an SDCC, an ICP-MS, several connectors, and Teflon tubes. Optimizations of adsorption pH condition, sample loading flow rate, and integration range were carried out to achieve optimum measurement conditions for REEs in seawater sample. Six minutes was enough for a preconcentration and measurement cycle using 10 mL of seawater sample, where the detection limits for different REEs were in the range of 0.005 pg mL(-1) to 0.09 pg mL(-1). Analytical results of REEs in a seawater certified reference material (CRM), NASS-5, confirmed the usefulness of the present method. Furthermore, concentrations of REEs in Nikkawa Beach coastal seawater were determined and discussed with shale normalized REE distribution pattern.

A lanthanum (La) coprecipitation method with low sample consumption was explored for the preconcentration of oxo-anion forming elements prior to a measurement by inductively coupled plasma mass spectrometry (ICP-MS). The preconcentration procedure was composed of two main steps: (1) the formation of a coprecipitate with the lowest possible La and (2) the redissolution of target analytes with minimal use of nitric acid, and the elimination of high concentration La from the analysis sample. Each step was performed in a 25 mL-volume syringe to reduce the sample consumption and to avoid contamination from the experimental environment. Various parameters, such as the concentration and volume of La added into the sample solution, the precipitation pH, the aging time, and the volume of HNO(3) were optimized to obtain good recoveries and high detection sensitivities for V, As, Sb, and W, which could be hardly recovered by solid-phase extraction using a chelating resin. The obtained method was evaluated through the analysis of seawater reference materials (CASS-4 and NASS-5). The recoveries exceeded 80%, and the observed values were in good agreement with the certified values.

The use of electrospray ionization mass spectrometry (ESI-MS) in negative ion mode was investigated as a direct probe for identifying Al species in Al-accumulating hydrangea (Hydrangea macrophylla) samples. Cell sap solutions of hydrangea leaves were purified using Sephadex G-10 liquid chromatography and each fraction was analyzed using ESI-MS and ESI-MS/MS to identify Al species. In hydrangea leaves, a 1:1 Al-citrate complex was found as [AlH(-1)cit](-) (m/z 215), where H(3)cit denotes citric acid. This result is consistent with that of Ma et al. who used (27)Al-NMR.

A tandem preconcentration method integrating chelating resin adsorption and La coprecipitation was applied to an analysis of Lake Baikal water by high-resolution ICP-MS. As a result, 56 elements were determined in Lake Baikal water: Ca, Na, Mg, K, Si, Sr, B, Li, Ba, P, Fe, Al, Mo, Zn, Mn, Rb, U, As, V, Cu, Pb, W, Y, Cs, Se, Cr, Ni, Ti, Sb, Zr, Sn, Co, Cd, Rh, Te, Hf, Nb, Ru, Ga, Sc, Th, Bi, and all-rare earth elements (all-REEs), except for Pm. The concentrations of these elements covered a range of nine orders of magnitude, from approximately 17 microg mL(-1) of Ca to less than 50 fg mL(-1) of Tm. The elemental concentrations in Lake Baikal water were compared with reference data.

The multielement determination of trace metals in seawater was carried out by inductively coupled plasma mass spectrometry (ICP-MS) with aid of a down-sized chelating resin-packed minicolumn for preconcentration. The down-sized chelating resin-packed minicolumn was constructed with two syringe filters (DISMIC 13HP and Millex-LH) and an iminodiacetate chelating resin (Chelex 100, 200-400mesh), with which trace metals in 50mL of original seawater sample were concentrated into 0.50mL of 2M nitric acid, and then 100-fold preconcentration of trace metals was achieved. Then, 0.50mL analysis solution was subjected to the multielement determination by ICP-MS equipped with a MicroMist nebulizer for micro-sampling introduction. The preconcentration and elution parameters such as the sample-loading flow rate, the amount of 1M ammonium acetate for elimination of matrix elements, and the amount of 2M nitric acid for eluting trace metals were optimized to obtain good recoveries and analytical detection limits for trace metals. The analytical results for V, Mn, Co, Ni, Cu, Zn, Mo, Cd, Pb, and U in three kinds of seawater certified reference materials (CRMs; CASS-3, NASS-4, and NASS-5) agreed well with their certified values. The observed values of rare earth elements (REEs) in the above seawater CRMs were also consistent with the reference values. Therefore, the compiled reference values for the concentrations of REEs in CASS-3, NASS-4, and NASS-5 were proposed based on the observed values and reference data for REEs in these CRMs.

Although ion exchange is often depicted as a process driven by electrostatic forces, ionic solvation or hydrophobic forces contribute greatly to ion exchange selectivity and is often the dominant factor. On a variety of commercial anion exchange columns, monovalent ClO4- elutes after doubly charged SO42- and even triply charged PO43-. For identically charged alkali metal ions, electrostatic charge densities based on crystal radii would suggest Li+ to be the most strongly retained on a cation exchanger. In practice, it is typically the least strongly held cation on most cation exchangers, because of its very high hydration energy and with most eluents its capacity factor approaches zero. Even when the ion is very poorly solvated, as with tetraalkylammonium (NR4+) cations, there has never been a report on a polymeric ion exchanger of an ideal electrostatic selectivity order where NR4+ cations elute in their increasing charge density order: R = n-butyl first, followed by n-propyl, ethyl, and last, methyl. We show that this selectivity order is easily achieved on recently described methracrylate-based monolithic capillary cation exchange columns (Ueki, Y.; Umemura, T.; Li, J. X.; Odake, T; Tsunoda, K. Anal. Chem. 2004, 76, 7007-7012) with minor amounts of hydroorganic modifiers. Indeed, under such conditions, Li+ (and other alkali cations) elutes after NMe4+.

A sensitive and fast-responsive evanescent wave absorption sensor has been constructed for pH measurements in highly acidic ranges. This sensor is based on a pH-dependent color change of protoporphyrin IX (PPIX). For the sensitive detection, a visible attenuated total reflection spectrometer with a slab optical waveguide (SOWG) was laboratory-made, and the guiding layer surface was modified with a PPIX-immobilized acrylamide-based thin membrane. The sensing membrane with a thickness of approximately 1 mum was directly fabricated on the SOWG glass surface by copolymerization of acrylamide, N,N'-methylene bisacrylamide, and PPIX in the narrow space confined by a cover plate. PPIX possesses two double bonds in its structure, and so it can be covalently incorporated into the membrane. The response characteristics of the PPIX-immobilized optode membrane were explored using aqueous solutions with different concentrations of HNO(3) or HCl. The optode membrane provided characteristic Soret band absorption spectra depending on the hydrogen ion concentration; the absorbance at 410 nm increased with increasing the concentrations in the range of 0.15-2 M, corresponding to the range of pH -0.3 to 0.8. The absorption signal reached 90% of its final value within 10 s, while the absorption signal was quite readily returned to background level simply by passing 2 mL of distilled water through a flow cell with a volume of 16.5 muL placed on the SOWG. Due to the rapid response and reversibility, this sensor could be operated in a flow-through mode as well as in a conventional static mode, where deionized water was conveniently used as a carrier and conditioning solution. In terms of the stability and precision, this sensor showed no significant change in response even after 100 assays and after being stored in a dry condition for over 6 months. Relative standard deviations for 10 replicate measurements were less than 1.8% in the linear range, and the detection limit calculated from 3 times of the standard deviation was 0.02 pH unit.

Hexyl methacrylate (HMA)-based monolithic semi-micro columns were prepared by in situ polymerization within the confines of 1.02-mm-i.d. silicosteel tubing for reversed-phase and/or precipitation-redissolution liquid chromatography. Practically useful monolithic columns with adequate separation efficiency, high permeability, and good mechanical strength were successfully obtained using a polymerization mixture comprising 24% hexyl methacrylate (HMA), 6% ethylene dimethacrylate (EDMA), 44.5% 1-propanol, and 25.5% 1,4-butanediol. The column performance was evaluated through the separations of a series of alkylbenzenes. At a normal flow rate of 50 microL min(-1), the produced HMA-based monolithic columns typically exhibited 3,000 theoretical plates for a 20-cm-long column, and the pressure drop was generally less than 1 MPa per 20 cm. The monolithic columns were resistant to at least 15 MPa, and could be properly operated at 15-20 times higher flow rate than normal, reducing the separation time to 1/15-1/20. The HMA-based monolithic columns were applied to rapid and efficient separations of proteins such as ribonuclease A, cytochrome c, transferrin, and ovalbumin in the precipitation-redissolution mode. Using a CH(3)CN gradient elution at a flow rate of 1,000 microL min(-1), four proteins were baseline separated within 20 s.

A flow injection analysis system was built with a liquid core waveguide spectrophotometric detector using an 80 cm Teflon AF-1600 capillary tube (2,2-bistrifluoromethyl-4,5-difluoro-1,3-dioxole/tetrafluoroethylene). The system was applied to determine nitrite ion in river water samples. The lower limit of detection for nitrite was 2.1 nmol dm(-3) (0.1 ng dm(-3) as NO(2)(-)) and the relative standard deviation of measurements was typically 0.56% (n = 5) at 0.21 micromol dm(-3).

Low flow-resistant alkyl methacrylate-based monolithic stationary phases of different hydrophobicity were constructed for reversed-phase capillary liquid chromatography by thermally initiated radical polymerization of respective methacrylate ester monomer with different alkyl chain (C2, C4, C6, C12, C18) and ethylene glycol dimethacrylate (EDMA) in a 250 microm i.d. fused silica capillary. The hydrophobicity was basically controlled by changing the length and/or the density of the alkyl-chain, while the composition and the ratio of porogenic solvent were adjusted to obtain highly permeable rigid monoliths with adequate column efficiency. Among the prepared monolithic stationary phases, C18-methacrylate monoliths polymerized from a binary porogenic solvent of isoamyl alcohol and 1,4-buthandiol exhibited the most promising performance in terms of hydraulic resistance and column efficiency. The pressure drops of 20-cm long monolithic columns were below approximately 0.4 MPa at a normal linear velocity of 1mm/s (a flow rate of 3 microL/min), and the numbers of theoretical plates for alkylbenzenes mostly exceeded 3000 plates/20 cm. The produced monolithic columns had good mechanical strength for high pressure and temperature, and could be properly operated even at a temperature of 80 degrees C and at a pressure of at least 33 MPa. At 80 degrees C, the theoretical plate numbers reached 6000 plates/20 cm because of the enhanced mass transfer. Due to the novel hydraulic resistance and mechanical strength, the separation time could be reduced 120-fold simply by raising the flow rate and column temperature.

Speciation of mercury in salmon egg cell cytoplasm was investigated by surfactant-mediated high-performance liquid chromatography/inductively coupled plasma mass spectrometry (HPLC/ICP-MS), where an ODS (octadecylsilica) column coated with a bile acid derivative, CHAPS (3-[(3-cholamidopropyl)-dimethylammonio]-1-propane sulfonate), was used for species separation. Prior to the speciation analysis, total Hg in the cell cytoplasm was determined by ICP-MS at m/z 202 in a flow injection mode. For the precise measurement, salmon egg cell cytoplasm was diluted five-fold with 0.1M Tris (Tris(hydroxymethyl)aminomethane)-HNO(3) buffer solution, and the standard addition method was employed. Thus, the total concentration of Hg in cell cytoplasm was estimated to be 12.4ngg(-1) on the wet weight basis. Next, the cell cytoplasm diluted five-fold with 0.1M Tris-HNO(3) buffer solution was analyzed by surfactant-mediated HPLC with the dual detection system of a UV absorption detector and an ICP-MS instrument. Two peaks corresponding to some proteins and small molecules were mainly observed in those chromatograms. When salmon egg cell cytoplasm was diluted five-fold with 0.01M Tris buffer solution or pure water, some precipitates appeared probably because of precipitation of hydrophobic proteins in cytoplasm. After the precipitates were eliminated with a membrane filter, the filtrate was subjected to the analysis by surfactant-mediated HPLC/UV/ICP-MS. As a result, the peaks for small molecular species of Hg were clearly observed at the retention time near 4.0min (corresponding to low-molecular weight zone) in the chromatograms with UV absorption detection as well as with Hg- and S-specific ICP-MS detections. The small molecule bound with Hg was identified as cysteine through the cysteine-spiked experiment. In addition, the protein fraction on the chromatogram obtained by using the CHAPS-coated ODS column was further analyzed by SEC (size exclusion chromatography). Consequently, several protein peaks with molecular weight of 300, 50 and 12kDa were observed in all the detections of UV absorption, Hg and Se, although two peaks among them were coincident in the case of S. These results indicate that Hg in salmon egg cell cytoplasm binds with proteins containing selenocysteine and/or cysteine residues in proteins.

The formation conditions and characteristics of a liquid/liquid optical waveguide (LLW) were studied using a two-phase sheath flow, where the inner organic phase flow acted as the core and the outer aqueous flow acted as the clad. In immiscible solvent systems, i.e., toluene/water and diethyl ether/water systems, the LLWs were formed in the range of higher than ca. 600 of the Reynolds number (Re), where the linear velocity of the organic solvent was much higher than that of the aqueous solution. On the other hand, in a miscible solvent system, i.e., a tetrahydrofuran/water system, a stable LLW was formed in the range of a much lower Re than in immiscible systems. Moreover, the molecules at the toluene/water interface of the LLW were observed with both fluorescence and absorbance measurement systems. In particular, the change in the fluorescence spectrum of 1-anilino-8-naphthalenesulfonate (ANS) at the interface within 1 ms was observed by this method, indicating the usefulness of the LLW for a fast kinetic study of a liquid/liquid interface.

An octadecylsilica (ODS) column modified with zwitterionic/nonionic mixed surfactants was evaluated for the direct injection determination of inorganic anions in biological fluids by ion chromatography. A zwitterionic surfactant (sulfobetaine-type) and a nonionic surfactant (polyoxyethylene-type) were used for a stationary-phase modification. When aqueous electrolyte solutions with concentrations of sub-mM to several mM were used as a mobile phase, the zwitterionic surfactant coated on the ODS surface exhibited unique separation selectivity for ionic species, while the nonionic surfactant coated on the ODS might have formed a hydrophilic network over the ODS surface and restricted matrix proteins from adsorbing on the stationary phase. Consequently, the mixed surfactant-modified column system allowed an efficient ion chromatographic separation of inorganic anions as well as a size-exclusive removal of column-fouling proteins. This separation system was applied to the direct injection determination of UV-absorbing anions in human saliva. The detection limits for nitrite, nitrate, iodide and thiocyanate were 3.1, 2.7, 4.5 and 25 microM, respectively, with UV detection at 210 nm (injection volume; 20 microl), and their relative standard deviations for 5 replicate measurements of saliva samples spiked with 100 microM each of those anions were 1.4, 0.9, 2.2 and 5.5%, respectively.

A sub-second, time-resolved, linear dichroism (LD) measurement system was constructed, fitted with a slab optical waveguide (SOWG), and utilized to observe the adsorption process of methylene blue (MB) onto silica surfaces. In the system, a semiconductor laser (670nm) was used as the light source and the out-coupled beam from the SOWG was split by a polarizing beam splitter into two polarized beams (TE and TM modes) to allow sequential linear dichroic ratio data to be obtained; the acquisition rate was 11 data sets per second. For an MB solution that contained no sodium dodecylbenzenesulfonate (DBS), in contact with a bare silica surface, a clear decrease occurred in the average orientation angle of adsorbed MB in the initial stages of the adsorption process. This result may correspond to a change in the chemical form of MB from monomer to dimer.

The determination of 34 trace metals in a river water certified reference material (CRM), i.e. JSAC 0301-1, which was issued by the Japan Society for Analytical Chemistry in January 2004, was performed by ICP-MS with a high efficiency nebulizer after preconcentration with a laboratory-made chelating resin-packed minicolumn, with which trace metals were concentrated 100-fold from 50 mL of a river water sample to 0.5 mL of the final analysis solution. Trace metals in JSAC 0301-1 were observed in the concentration range from 19 microg L(-1) of Al to 0.000053 microg L(-1) of Bi. It was found that most of the concentrations of trace metals, including rare earth elements (REEs), in JSAC 0301-1 were lower than those in JAC 0031, which was also a previously issued CRM prepared with water from the same river as that of JSAC 0301-1. The low concentrations of trace metals in JSAC 0301-1 might be attributed to the fact that there was a heavy rain before collecting the original water sample to prepare the present CRM. Furthermore, the REE distribution patterns of JSAC 0301-1, JAC 0031 and the average values of river water samples in Japan were parallel to each other. These results indicate that the distributions of REEs in JSAC 0301-1 and JAC 0031 were the typical ones of river water samples in Japan.

A new isoelectric focusing (IEF) system for two-dimensional polyacrylamide gel electrophoresis (2-D PAGE) has been proposed. In this system, a super-soft and tough IEF gel was achieved by casting polyacrylamide gel down to 2.0% T using a loose multifilament string (LMS) of nylon as a gel support. The IEF apparatus for the LMS-gel, fabricated from acrylic boards, had a cooling water chamber, and eliminated the need of electrode solutions by directly connecting the two ends of individual gels to platinum electrodes. The carrier ampholyte-generated pH gradients using the new IEF system was stable over a long duration of time and a wide range of voltages, and the IEF time became shorter using a 2.0% T gel than using a 4.0% T gel. Also, the LMS-gels prepared in different runs exhibited excellent reproducibility. The new IEF system was applied to 2-D PAGE of a chicken skeletal muscle extract, and it was found that the protein loading capacity, protein entry into the LMS-gels, and protein transfer efficiency from the first-dimensional to the second-dimensional gels were significantly improved by using a low-concentration (2.5% T) gel. Also, proteins of high molecular weight of more than 200 kDa were observed in the 2-D maps, and therefore the new IEF system has a very good potential to be applied for fast 2-D PAGE of high molecular-weight proteins.

Polymer-based strong cation-exchange monolithic capillary columns with different capacities were constructed for ion chromatography by radical polymerization of glycidyl methacrylate (GMA) and ethylene dimethacrylate in a 250-microm-i.d. fused-silica capillary and its subsequent sulfonation based on ring opening of epoxides with 1 M Na(2)SO(3). The cation-exchange capacities can easily and reproducibly be controlled in the range of up to 300 microequiv/mL by changing the immersion time of the epoxy-containing polymer in the Na(2)SO(3) solution. The chromatographic performance of the produced monolithic capillary columns was evaluated through the separation of a model mixture of common cations such as Na(+), NH(4)(+), K(+), Mg(2+), and Ca(2+). As an example, these cations could be well separated from one another on a 15-cm-long cation-exchange monolithic column (column volume, 7.4 microL) with a capacity of 150 microequiv/mL by elution with 10 mM CuSO(4). The pressure drop of this 15-cm column was approximately 1 MPa at a normal linear velocity of 1 mm/s (a flow rate of 3 microL/min), and the numbers of theoretical plates for the cations were above 3000 plates/15 cm. This GMA-based cation-exchange monolithic column could withstand high linear velocities of at least 10 mm/s. Over a period of at least two weeks of continuous use, no significant changes in the selectivity and resolution were observed. The applicability of a flow rate gradient elution and the feasibility of direct injection determination of major cations in human saliva sample were also presented.

27Al NMR spectra of an equimolar (10 mM) Al(III)-citrate system were obtained at different temperatures. The linewidths of the signals decreased in the spectra recorded at elevated temperatures, which enabled us to unequivocally identify the resonance lines. From the spectrum recorded at 65 approximately C, a mononuclear Al(III)-citrate complex was identified at a solution pH of 3.0 in addition to trinuclear Al(III)-citrate complex, which dominated at pH 4.0.