Search

The increasing accumulation of rock waste obtained due to ore processing and its environmental impacts, such as acid mine drainage and elevated concentrations of heavy metals in soils, necessitates the transformation of mining technologies based on the concept of circular waste management. The research is aimed at improving the parameters of the mechanical activation effect produced on technogenic georesources, as well as at expanding the application scope of disintegrators in the field of using the partial backfill of the mined-out space when developing stratified deposits. In this regard, the research purpose was to substantiate the parameters of extracting metals from enrichment tailings using their mechanochemical activation to ensure cyclic waste management. The research involved the application of three-dimensional interpolation methods used for processing the data and the graphical representation. As a result, the following was found to be characteristic of the waste of the Sadonsky mine management. The degree of extracting zinc from pre-activated tailings increases logarithmically when the H 2 SO 4 concentration and the NaCl proportion decrease 3.5 times. The degree of extracting lead from the activated tailings increases according to the Fourier law when decreasing the NaCl mass concentration, and an optimal range of the H 2 SO 4 (0.38-0.51%) proportion decreases six times. One of the key results of the research is the justification of expanding the scope of applying disintegrators in the case of a directed activation influence exerted on the components of the stowing strips. The obtained results expand the understanding of the mechanism of the influence of the mechanochemical activation of dry tailings on the reactivity unevenness when extracting several metals from them.

The aim of this study was to investigate cutting force when milling 40 × 13 stainless steel samples obtained via electron-beam surfacing. The samples were obtained by surfacing the wire made from the martensitic 40 × 13 stainless steel. The microstructure of the samples and the hardness are discussed in the present study. Emphasis is placed on the study of cutting forces when handling the samples. The structure of the samples obtained by electron-beam surfacing consisted of tempered martensite. The average hardness of the samples was similar to the hardness obtained after quenching and tempering the samples-576 HV for horizontally printed workpieces and 525 HV for vertically printed workpieces. High-speed milling, high-efficiency milling, and conventional milling have been proven to be suitable for handling such workpieces. This study shows that an increase in milling width leads to a gradual decrease in specific cutting force. As the milling depth increases, the specific cutting force decreases intensively at first but then more slowly with time. Machining the workpieces made of the martensitic stainless steel and produced by electron-beam surfacing requires the use of purely carbide mills with a diameter of at least 12 mm. Using a high-speed steel as a tool material results in the rapid failure of the tool. The cutting conditions during the investigation allowed for a decrease in the temperature of the cutting edge, cutting force, and the low-rigid end mill bending. Therefore, this study has made it possible to select modes that allow for a reduction in the vibration of the lathe-fixture-tool-part system.

The increase in the share of physical and technical processing methods in the arsenal of deburring technologies used in modern production is associated both with the use of difficult-to-machine materials, such as beryllium bronze and the 29 NK alloy, and with the need to solve technological problems for the production of small-sized products with hard-to-reach surfaces. The aim of the study is to improve the processes of blade processing of small-sized parts made of beryllium bronze and the 29 NK alloy to provide rational conditions for thermal pulse deburring. Surface samples were experimentally obtained after turning in different modes on a CITIZEN CINCOM K16E-VII automatic lathe equipped with an Applitec micromechanics tool. The surface quality and burr characteristics were examined using a JEOL JIB-Z4500 electron microscope and a ContourGT-K optical profilometer. The program Statistica 6 allowed processing of the results. The relationship between the parameters of the turning mode and the thickness of the root of the burrs formed on the machined surface, the limitation of which is one of the conditions for the application of the thermal pulse method, was established. The obtained empirical regression dependencies establish a rational range of cutting mode parameters, and the implementation of the formulated recommendations for setting blade modes ensures deburring by the thermal pulse method in compliance with the requirements of drawing under maximum processing performance.

This article is devoted to the development of a classification method based on an artificial neural network architecture to solve the problem of recognizing the sources of acoustic influences recorded by a phase-sensitive OTDR. At the initial stage of signal processing, we propose the use of a band-pass filter to collect data sets with an increased signal-to-noise ratio. When solving the classification problem, we study three widely used convolutional neural network architectures: AlexNet, ResNet50, and DenseNet169. As a result of computational experiments, it is shown that the AlexNet and DenseNet169 architectures can obtain accuracies above 90%. In addition, we propose a novel CNN architecture based on AlexNet, which obtains the best results; in particular, its accuracy is above 98%. The advantages of the proposed model include low power consumption (400 mW) and high speed (0.032 s per net evaluation). In further studies, in order to increase the accuracy, reliability, and data invariance, the use of new algorithms for the filtering and extraction of acoustic signals recorded by a phase-sensitive reflectometer will be considered.